Location Configuration in Centralized CallProcessing Deployment

Hello Friends,
In Centralized Call Processing, What is the parameters or consideration for configuring the Bandwidth in "Location" under CUCM which is different from reserving the RT Bandwidth for that particular site in Gateway?
Do we need to consider the On-Net, VMProfile, Announcements only or still there are more to consider to avoid any CAC issues.
Regards,
Bala

Bala,
This is well described in the CAC section of SRND, you can use the Hub_none location for centrelized resources.
Chris

Similar Messages

Can anybody explain how to configure the Centralized contract in SRM 7

Hi All,
Can anybody explain how to configure the Centralized contract management in SRM 7 with ECC EHP4 ?what are all that need to be perform in PI system.
Thank you,
praveen

Hello,
PI will be required here. You can also refer the config guides maintained at the belwo mentioned location.
Goto URL http://service.sap.com/srm-inst and then navigate to SAP SRM --> SAP SRM Server 7.0 -> Configuration Guides for SAP SRM 7.0
Best Regards,
Rahul

OU For Lync 2013 Central Forest deployment when using GAL Sync

Hello,
We are attempting to set up Lync 2013 in a Central Forest configuration. We have a 2 way forest trust in place. The primary forest being A.com, the secondary forest being B.com. Exchange 2010 is deployed in both forests. Lync 2013 is deployed in forest A.com.
We currently have FIM 2010 installed, using GAL Sync between both forests. For GAL Sync, we have an OU in Forest A.com active directory called GALSync. There are currently contacts in that OU that correspond with the user accounts in forest b.com. Here's
my question:
When configuring FIM MA's for Lync 2013 Central Forest deployment, can I point the LCSCFG.xml file to the SAME GALSync OU we use for GAL Sync? Will it see the contacts already exist and just update with the necessary attributes needed to provision
the forest B.com users for Lync? Do I need to create a separate OU for the Lync MA to use? Or, am I going about this in the wrong way?
Any help you can provide will be greatly appreciated.
Thank you

Thanks for the reply Anthony
Almost right. The only difference is that the remote users will get the autodiscover url and the ews url from their local domain and dns.
Here is how it is setup:
Shared public namespace
mycompany.com (email address and sip address use this in both domains)
Central Forest (mycompany.com)
Lync 2013
Exchange 2013
Autodiscover url
autosdiscover.mycompany.com/autodiscover/autodiscover.xml
192.168.10.10
EWS Url
https://mail.mycompany.com/EWS/Exchange.asmx
192.168.10.11
Remote Forest (Fabrikam.com)
Lync 2010
Exchange 2010
Autodiscover url
autosdiscover.mycompany/autodiscover/autodiscover.xml
192.168.11.23
EWS Url
https://mail.mycompany.com/EWS/Exchange.asmx
192.168.11.24
User in Fabrikam login locally with their Fabrikam credentials. They have a Lync enabled contact in mycompany. There is a 2 way trust in place. They login to mycompany Lync fine.
When they do the autodiscover DNS lookup, they return the same autodiscover and EWS url, but they point to the local Exchange 2010 since their mailbox and user account still resides there and that is the system that the Fabrikam account has access to.
Autodiscover works fine for Outlook.
I will take a look at Fiddler

Fiori CRM apps with central hub deployment

Hello Experts,
We are looking to configure Fiori CRM apps in our landscape with central hub deployment option. Our CRM backend and frontend server (Gateway) are 2 separate systems.
The CRM backend system (CRM 7.0 EHP3) is running NW 7.4 whereas the frontend server where we have installed the Gateway component is running NW 7.31. Can we go ahead and install the CRM UI components on our frontend server or is it mandatory that the frontend server also runs NW 7.4?
Regards,
Saurabh
Tags edited by: Michael Appleby

Hi Masa,
The link you mentioned gives details about the required SAP Gateway Components for NetWeaver 7.3 & 7.4, but does not mention anywhere whether the NetWeaver version of the backend business suite system should necessarily be NW7.4 if we have front-end system on NW7.4.
I am looking to clarify the doubt regarding whether both front-end and back-end systems should be on the same NetWeaver release or it is fine to have front-end on 7.31 and back-end on 7.4
Regards,
Saurabh

Connection Configuration to Central Services Registry in PI7.1

Hi Freinds,
while in CE7.1-
NWA->Configuration Wizard-> I have this set up file Connection Configuration to Central Services Registry to configure the central service registry.
while on PI7.1 EHP-1
I dont have this setup file Connection Configuration to Central Services Registry.
Is this included in Any Configuration service, or with different name?
Regards
chandra Dasari

Hello Chandra
See the link below.
Configuring a Central Services Registry
http://help.sap.com/saphelp_nwpi71/helpdata/EN/46/bb923d06582710e10000000a11466f/content.htm
Regards
Mark

Missing "Connection Configuration to Central Services Registry" in Config Wizard in NWA

Hi,
When we trying to do the following operation [ by referring the document http://www.google.co.in/url?sa=t&rct=j&q=&esrc=s&source=web&cd=5&cad=rja&uact=8&ved=0CD8QFjAE&url=http%3A%2F%2Fdocencia.…]
Configuration Management > Scenarios >
Configuration Wizard > Start the Connection Configuration to Central Services Registry task in NWA for setting up the Service Registry, we don't see this task in the list.
Can someone help me in starting this task ???
Regards,
Samba

Hello Chandra
See the link below.
Configuring a Central Services Registry
http://help.sap.com/saphelp_nwpi71/helpdata/EN/46/bb923d06582710e10000000a11466f/content.htm
Regards
Mark

No SOA configured servers found for deploying

Hi
I am very much novice in BPEL. I have created a very small BPEL process and tried to deploy it in Weblogic Server.I get this message in the deployement log:
[11:55:13 AM] #### Deployment incomplete. ####
[11:55:13 AM] No SOA configured servers found for deploying the archive file:/D:/JDeveloper/mywork/chapter2/EchoComposite/deploy/sca_EchoComposite_rev1.0.jar
(oracle.tip.tools.ide.fabric.deploy.common.SOARemoteDeployer
I checked the entreprise manager (EM) & I discovered that I have no SOA folder ,no soa_infra and no managed server called soa_server1 in my managed servers list!!
can you help me to fiw this please?
regards!
Edited by: 867232 on 7 juil. 2011 05:55

Login to weblogic admin console and go to section "Deployments". Make sure that application SOA-INFRA is in active state. If it is not then check SOA server startup log to find out any errors which could not let SOA-INFRA deploy. You may refer -
No SOA configured servers found for deploying
Regards,
Anuj
Edited by: Anuj Dwivedi on Jul 8, 2011 9:41 AM

Configuration manager 2012 Client Deployment settings.

GPO to push config mgr client
i have added The Configuration Manager templates in GPO
Under Configure Configuration manager 2012 Client Deployment settings.
I have enabled it and what is the command line here
CCMSetup.exe SMSSITECODE=COD FSP=sccm.mydomain.com MP=sccm.mydomain.com
or
SMSSITECODE=COD FSP=sccm.mydomain.com MP=sccm.mydomain.com
or
CCMSetup.exe /MP:sccm.mydomain.com /logon SMSSITECODE=COD SMSSLP=sccm.mydomain.com FSP=sccm.mydomain.com
or
/MP:sccm.mydomain.com /logon SMSSITECODE=COD SMSSLP=sccm.mydomain.com FSP=sccm.mydomain.com

You can use the following:
CCMSetup.exe
SMSSITECODE=COD FSP=sccm.mydomain.com MP=sccm.mydomain.com
http://prajwaldesai.com/deploying-configuration-manager-2012-r2-clients-using-group-policy/
http://methmal132.wordpress.com/2013/02/13/how-to-push-the-sccm-agent-via-gpo/
Regards, Ibrahim Hamdy

How to identify inbound location on a centralized Attendant Console?

I'm trying to find a way to be able to identify for our centralized receptionists the location of the inbound calls.
We have 16 sites set up with Cisco routers as h323 gateways each pointing all incoming calls to the main phone line to a separate AC pilot point in CCM 4.13sr3b. Is it possible to have the dialpeer put some sort of description tag that the receptionists can see on attendant console when the call comes in that says where/which site this phone call is coming in from? Or display the queue it is coming in on?
Any ideas on this would be appreciated. I'm trying to avoid going down the IPCC path to provide this functionality since Cisco won't support IPCC and attendant console running simultaneously.
Bottom line is we have a multi site CM deployment where all inbound calls going to a central group of folks running attendant console and we need to be able to discern which pilot point or voice gateway the call is coming in on.
I appreciate any thoughts on this!!
Ryan

One way to do this if you don't care about the caller ID of the calling party, would be to tranform the calling number to DN of the Pilot DN by using Translation Patterns. Basically the GW's CSS would not have access to the AC Pilot, but to a TP that transforms the calling party and redirects to the AC Pilot.
HTH, please rate all posts!
Chris

ERROR: TCP Locator (Configuring the caching loactors) ERROR

Hi All,
I am attempting to deploy LiveCycle ES to a WebLogic cluster which
reside on 64bit servers. Before I can run the configuration manager,
there is a step to run a batch file (startlocator.bat) in order to
configure the caching locators.
This batch file errors out with the following message:
"ERROR: operation "start-locator" failed because: Start of locator
failed. The end of "F:\Adobe\LiveCycle8.2\lib\caching\locator.log"
contained this message: "".
I checked the log and just like the above error message mentioned,
there was nothing written into the log. Please help. How can I get
this working, or better yet, how important is this step?
PS. This step is located on pg. 27 of the "Configuring LiveCycle ES
Application Server Clusters Using WebLogic" documentation.
Regards,
Ikhide

Hi Jonathan,
Could you please provide your OS details- Windows/Unix?
If it is any unix flavor system, please execute dos2unix command on startlocator.sh and run it again.
Thanks,
Pankaj Parashar

Location Configuration for Tax Types VAT, Excise

Hi,
Our Client has manufacturing plants, Depot Sales in different states and even more than one plant in a State with different excise registrations.
Some of the products are excisable and some are not.
The requirement is Vat payble is to calculated State wise (for all the Depot in the State) and Cenvat is calculated for each Division (for each excise registration)
For Vat purpose if i configure Location as State and wareshouse as Depot, i am able to generate the tax payment wizard, XL Reporter like purchase register and sales register by using location as state
But for CENVAT if location is selected as state only one division report (as only one ECC no. can be linked to location) can be generated, but our client has plants with different ECC nos. in the same state.
Alternatively,
If i create seperate location for each ECC no., i am not able to generate the Vat report state wise.
How to configure the Locations ?
Please suggest.
Thanks,
Kumar.

Dear M K kumar,
As per your requirement you only run Tax wizard by location.
For VAT you have not an issue.
but for excise payment not possible.
So for that if you you have two ECC No. in one state so create two location Like Maharastra1 & Maharastra2
and check accordingly.
Regards
MANGESH PAGDHARE.

Withholding tax by location configuration

Hi all,
I wonder if anyone can help me with this. We want to be able to report withholding tax by location(where job is carried out not necessarily vendor location). What configuration can I put in place to facilitate this sort of reporting?

What I am actually trying to achieve is to be able to run withholding tax reports by states in Nigeria. This will mean entering each transaction with a location/region so that when this report is run I can sort through these figures by states. The only thing I can think of is to create a different code for every region but I am thinking there maybe a way of simply entering the region/location when posting the transaction. Is this possible?

Configuration for Central Monitoring System in SAP Solution Manager.

Hi Folks,
I am trying to setup Central System Monitoring in SAP Solution Manager, I am following the document which mention the step by step instructions.
There are couple of items on which I am really confused.
In the documentation it says to activate Background Dispatching & Central System dispatching in 000 client of Solution Manager,
it also mentioned about creating CSMREG user, but it did not say in which client this activity needs to be performed, and there are lot many steps in which there is no mention about the client of solution manager in which we have to perform the configuration.
Can you guys please help me to configure properly?
One set document which I saw talks about the configuration using RZ21 and other document discuss about Configuration using System Monitoring Work Center, which one do we need to follow, are both methods are 2 different options doing the same thing, can you please clarify?
Also, is there any document which clearly explains the setup of Central System Monitoring in SAP Solution manager using both approaches and also to test the monitoring?
I have SAP Solution Manager 7.0 EHP1.
Thanks.
Jennifer

Hi,
>
> it also mentioned about creating CSMREG user, but it did not say in which client this activity needs to be performed, and there are lot many steps in which there is no mention about the client of solution manager in which we have to perform the configuration.
>
You should created this user in working client.
> Can you guys please help me to configure properly?
>
> One set document which I saw talks about the configuration using RZ21 and other document discuss about Configuration using System Monitoring Work Center, which one do we need to follow, are both methods are 2 different options doing the same thing, can you please clarify?
>
You can use RZ21 or System monitoring through work center. From Solution manager 7.1, you need to use work center only. So, I would suggest you to use work center only.
Thanks
Sunny

Configure WiFi network and deploy via e-mail

Hi,
I'm running into problems when I configure a WPA2 WiFi network with iPhone Configuration Utility v3.3 and send the profile to an iPad with iOS 4.3.5 via e-mail. If I try to use the internet over WiFi after that, it always asks me for the WPA2 passphrase I configured in iPhone Configuration Utility. If I deploy the same profile to the same device via cable, everything works fine.
Any suggestions?
Thanks,
felix

Not really, no. The iPhone does not have printer drivers, so you cannot print documents, etc., from it. With an HP printer with Wi-Fi, you can print photos (only photos, not documents) using an App from HP:
http://itunes.apple.com/WebObjects/MZStore.woa/wa/viewSoftware?id=299531647&mt=8
Also, note that you can take a screenshot on your iPhone (quick press of home and sleep/wake buttons), which is saved as a photo, and that can be printed using the above app. But, you are limited to one iPhone screen per printout.

Package Configuration Wizard or Project Deployment Model

I am using SQL Server 2012 and I have multiple SSIS packages working in DEV.
My aim is to deploy these to File System for execution by a Windows Service application. Should I therefore using the Package Configuration Wizard for storing DEV and PROD server details?
Is the Project Deployment Model only required when deploying to SQL Server?

Hi DarrenOD,
The project deployment model enables you to deploy your projects to the Integration Services server. And there are some features like Parameters, Environment, Environment variables, SSISDB catalog and Catalog stored procedures and views that are available
to projects developed only for the project deployment model.
After converting project deployment model to package deployment model, there are four steps in the package deployment process:
The first optional step is optional and involves creating package configurations that update properties of package elements at run time. The configurations are automatically included when you deploy the packages.
The second step is to build the Integration Services project to create a package deployment utility. The deployment utility for the project contains the packages that you want to deploy.
The third step is to copy the deployment folder that was created when you built the Integration Services project to the target computer.
The fourth step is to run, on the target computer, the Package Installation Wizard to install the packages to the file system.
Reference:
Deployment of Projects and Packages
How to: Deploy a Package
Thanks,
Katherine Xiong
Katherine Xiong
TechNet Community Support

Location Configuration in Centralized CallProcessing Deployment

Similar Messages

Maybe you are looking for