Low sound. Brand new Pavilion Elite HPE-410f Tower and HP 2310m Monitor
Monitor does have the speakers and they are working, but the volume is so low as too be useless. What can I do to boost the sound. Was paying the extra money for internal speakers on a HP monitor a stupid thing to do? Can I even plug extra speakers in without disabling the monitor speakers?
Help!!! Thanks for any advice.
How did you connect audio to the monitor? (analog with a separate cable or HDMI audio)
Did you turn up the audio in the monitor's menu?
If using HDMI audio, what video card are you using?
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT
Similar Messages
-
HP Pavilion Elite HPE-480t computer and an HP bd 340i 12x blu-ray writer
I purchased HP 12x Blu-Ray writer model bd340i in the middle of last year. When I purchased my desk top from HP in December of 2010 model HP Pavilion Elite HPE-480t I installed the burner and every thing was working fine. Today I tried to burn a blu-ray disc and it came back with can not read media, that was on imgBurn. So I tried the same on the systems burner and it came back as no disc in tray. I also tried CyberLink burning software and the same thing no disc.
I then tried to play both store bought and home made blu-ray disc and it could not read the media. I was ready to blame it on a bad burner but I then tried a regular DVD both store bought and home made and it played fine. I then tried to burn a dvd single and dual-layer with all three burning softwares I have and again it was fine, no problems. Its just the blu-ray media that can not be read or writen. The only blu-ray media I used from day one has been Kodak and never had a problem. Thats what baffles me.
I at this point dont know if its a hardware or software problem with the computer or blu-ray burner or both. 3 different burning programs works fine on DVD's but not blu-ray, Plays DVD's fine but can not play or burn blu-ray discs.
Could it be the blu-ray laser crapped out and the dvd reading and writing laser is still working ? Does a blu ray burner even have to lasers for the two medias [DVD and Blu Ray]???
Everything else with the computer works fine. I even tried uninstalling and reinstalling and its the same, I tried to update the drivers and firmware on your site and still did not work. Please some help.
When did you purchase your product? : December2010
Product HP Pavilion Elite HPE-480t CTO Desktop PC
Select a problem area: other
What is your serial number (SN): [Personal Information Removed]
What is your operating system?: Microsoft Windows 7 Home Premium 64
Is your computer unable to work with accessory products? Please select all that apply. other
What type and brand of CD/DVD media do you use? Kodak Bu-Ray 25gig and HP dvd
Was the CD/DVD writer drive built into the computer when you purchased it? No
Can you hear the sound from the connected speakers?
Does the display on the product appear to be working properly? Yes
Have you connected the product to your TV, DVD player, or music system? No
If there is an error message, please specify: can not read media
Problem Description: I purchased HP 12 Blu-Ray writer model bd340i in the middle of last year. When I purchased my desk top from HP in December of 2010 model HP pavilion Elite HPE-480t I installed the burner and every thing was working fine. Today I tried to burn a blu-ray disc and it came back with can not read media, that was on imgBurn. So I tried the same on the systems burner and it came back as no disc in tray. I also tried CyberLink burning software and the same thing no disc. I then tried to play both store bought and home made blu-ray disc and it could not read the media. I was ready to blame it on a bad burner but I then tried a regular DVD both store bought and home made and it played fine. I then tried to burn a dvd single and dual-layer with all three burning softwares I have and again it was fine, no problems. Its just the blu-ray media that can not be read or writen. The only blu-ray media I used from day one has been Kodak and never had a problem. Thats what baffles me.
Please provide previous troubleshooting steps, or information that can help HP assist you.: I at this point dont know if its a hardware or software problem with the computer or blu-ray burner or both. 3 different burning programs works fine on DVD's but not blu-ray, Plays DVD's fine but can not play blu-ray.
Has anything changed since the unit functioned properly (installation of SW, settings, cabling, etc.): Everything else with the computer works fine. I even tried uninstalling and reinstalling and its the same, I tried to update the drivers and firmware on your site and still did not work. Please some help.
How would you describe your technical skill level?: Intermediate
First name Peter
Last name Cavalier
[Personal Information Removed]
This question was solved.
View Solution.Arcticwolf, welcome to the forum.
Let's try another burner to see if that helps solve your problem. I have used CDBurnerXP for years. It has burned CD/DVD's when no other burner would work.
Please let us know if this solves your problem or not.
Signature:
HP TouchPad - 1.2 GHz; 1 GB memory; 32 GB storage; WebOS/CyanogenMod 11(Kit Kat)
HP 10 Plus; Android-Kit Kat; 1.0 GHz Allwinner A31 ARM Cortex A7 Quad Core Processor ; 2GB RAM Memory Long: 2 GB DDR3L SDRAM (1600MHz); 16GB disable eMMC 16GB v4.51
HP Omen; i7-4710QH; 8 GB memory; 256 GB San Disk SSD; Win 8.1
HP Photosmart 7520 AIO
++++++++++++++++++
**Click the Thumbs Up+ to say 'Thanks' and the 'Accept as Solution' if I have solved your problem.**
Intelligence is God given; Wisdom is the sum of our mistakes!
I am not an HP employee. -
Can't record sound on HP Pavilion Elite HPE
I have Windows 7 installed and am trying to get Dragon Premium to work on my computer. Unfortunately, I've tried two different mikes and neither can record on my system. I've gone through all the standard troubleshooting for sound recording. The devices are recognized. The system sound is up. The mikes are plugged into the proper inputs for mikes. I've gone through every step available on the help documentation software.
Any other ideas?
Thanks in advance!
SkydancerHello Skydancer1
I am sorry to hear you are having issues getting microphones to work with your computer. I would like to offer my assistance in this matter. I am providing you with the HP Support document Resolving Microphone and Line-in Problems (Windows 7) which has been created with the steps needed to resolve issues like what you are describing. I would recommend that you review the document and follow the troubleshooting steps to resolve your issue.
If this does not provide you with a solution I would encourage you to post your product number for your computer. I am linking an HP Support document below that will show you how to find your product number. As well, if you could indicate whether your operating system is 32-bit or 64-bit as with this and the product number we can provide you with accurate information.
How Do I Find My Model Number or Product Number?
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=c00033108
Is the Windows Version on My Computer 32-bit or 64-bit?
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=c02033168
I would like to thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter -
HP Pavilion Elite HPE-025sc Blackscree​n when logged in!
Last friday i just started my pc normally. When i logged in i got nothing on my desctop.
I got a HP Pavilion Elite HPE-025sc
I've tried system restore but i have no restore point.
I've also tried to do system repair but it tells me that i have a usb just plugged in. So i tried to remove my mouse, keyboard but then i knew i couldn't do anything without keyboard so i plugged in a new.
How can i fix this?
Please help!Hi Droxx1337,
I understand that you are having an issue with getting your computer to load into Windows. I have included the document here for, 'Windows 7 Does Not Start'. This document will take you through generic as well as specific steps to hopefully get you into Windows.
If this document fails to resolve the issue, please let me know what version of Windows you are running. I have included the document 'Which Windows operating system am I running?'.
Please let me know if this works, thank you.
I worked on behalf of HP -
Unable to use Recovery Manager on HP Pavilion Elite HPE-112y PC Windows 7
HP Pavilion Elite HPE-112y PC.
Genuine Windows 7 Home Premium - 64-bit.
I'm having problems with my Recovery Manager. A few days ago it was working fine. The other day when I tried to access either the "Software Program Reinstallation" or the "Hardware Driver Reinstallation" to check something out, both my DVD and BD drives opened and a message popped up saying:
This system does not have a recovery partition. The recovery process needs to use the set of recovery discs you created previously. Please insert disc #1 now.
I did not create any such recovery discs. I don't know how this happened. When I looked at the "I'd like to take precautions" section of the Recovery Manager, the "Recovery Disc Creation" and the "Remove Recovery Partition" are grayed out, but the "View Recovery Report" is still active and there is some kind of report in it. I don't know what the report means.
I did ask for advice somewhere else and was asked to post a screenshot of my Disk Management from the Computer Management. After seeing the screenshot, I was told that my recovery partition is there and in good health and there is a possibility that something is preventing the recovery process from seeing it.
I'm asking around for advice before I try anything. I want to be very cautious before I do anything drastic.
Is there a chance that I can find my Recovery Partition and restore it? Or will I have to do a full System Recovery to get it restored?
===============
I'm not trying to make any changes yet, but I thought I would take a look at the System Recovery in the Recovery Manager. When I click the System Recovery button this is what I see.
Restore your computer to its original factory condition.
Your computer does not have a Recovery partition.
If you want to continue the restoration process, make sure you have inserted disc #1 and then click "Yes" to continue, or click "No" to exit.
Is this going to be a problem if I need to restore my system?Hi,
Even though the Recovery Manager software is unable to launch a system recovery, the f11 option may still work as it uses an entry in the BCD ( boot configuration data ) to launch via the f11 method at start-up. Saying that, I would definitely recommend getting a set of Recovery discs in case it does launch correctly, just to be on the safe side.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience -
How can I add USB 3.0 to my HP Pavilion Elite HPE-190t CTO Desktop PC?
How can I add USB 3.0 to my HP Pavilion Elite HPE-190t CTO Desktop PC? It uses Windows 7 Pro 64-bit OS.
I can't tell how many or if there are expansion slots inside the case. Is there a reliable source for such an expansion card?Considering the different options that PC could have been ordered with, it might be there is not an empty slot to mount a PCI add-on card to add a USB 3.0 card. It would be advisable to open the case to see if there is an empty slot. If there is, then THIS is a choice to add USB 3.0
{---------- Please click the "Thumbs Up" to say thanks for helping.
Please click "Accept As Solution" if my help has solved your problem. ----------}
This is a user supported forum. I am a volunteer and I do not work for HP. -
Should I remove the blue film on the battery of my brand new Pavilion 15 - n096sa laptop?
Should I remove the blue film on the battery of my brand new Pavilion 15 - n096sa laptop?
Hi
>>I am so sorry about that what happned with your computer
>>I would suggest please try doing a system test for F2 fallow the below link
Testing for Hardware Failures (Windows 8)
>>and I belive you have performed recovery using F11
>>If still didint work try contacting ebay
>>or else call us @ 1800-474 - 6836 and get a set of recovery disc
>>try performing recovery using disc
Please click "Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
Click the "Kudos, Thumbs Up" on the bottom right to say "Thanks" for helping!
I am an HP employee -
HP Pavilion Elite HPE 502c gets stuck in a reboot loop
HP Pavilion Elite HPE 502c
Windows 7
When I boot the computer, it gets to the blue screen with the hp logo. then the screen goes black, without the logo. It then goes to the blue screen, then black. It repeats the process untl I turn off the computer.Hello @aschwan41,
I understand that your HP Pavilion Elite HPE-502c Desktop PC will not start up properly and you are looking for assistance. I am providing you with an HP Support document: Computer Does Not Start (Windows 7), which addresses startup issues that can affect all HP and Compaq desktop, All-in-One, and HP TouchSmart computers that come with Windows 7. I recommend that you review the document and follow the steps that pertain to your particular issue.
Please re-post if you require additional support. Thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter -
Remote HP Pavilion Elite HPE 020be Desktop PC
hi,
after installed windows 8 on my pc (HP Pavilion Elite HPE 020be), my remote (rc1804904/06 - P/N 5070-2586) stopped working.
is there any way to fix this issue? i already tried to install the HP Remote Solution software, but no change.
thanks.Hello @lockstock,
I understand that after updating your operating system to your HP Pavilion Elite HPE 020be Desktop PC to Windows 8 your HP Remote will not work and you require assistance. According to the HP Pavilion Elite HPE-020be Desktop PC Drivers page there are no drivers for your computer running Windows 8. Part of what you should expect when upgrading your operating system to one that may not be fully supported it the loss of some functionality. I suspect that this is what you are facing currently with your remote. There are no drivers for your computer so the remote is sending the signals, but the hardware on your computer has no way to receive it or if it does to enterpret it correctly.
I hope I have answered your question to your satisfaction. Thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter -
HELP! brand new iMac froze during firewire transfer and won't start!!!
During my setup for my brand new iMac I follwed the directions and connected my iBook via firewire to transfer my files. I noticed after a while that my iMac was frozen on "45 minutes remaining" and the blue line wasn't wavering a bit, and after over half an hour it hadn't moved. I powered off the iBook, and still nothing happened to the iMac screen--it remained frozen. I went to the guidebook and nothing seemed to work, so I powered off and on again, only to get a flashing question mark. All this and I just bought the darn thing tonight!
Help! Anyone know what happened and more importantly how to fix it?
Thanks.
Lindsayit sounds like the iBook went to sleep during the transfer or at least it's hard drive spun down.
what you need to know is hope that simply booting from your install DVD will let you repair the iMac's hard drive. You could also try booting holding down the Command S keys on startup and when you get to the Single User Mode command line prompt follow the directions there for running fsck to repair your hard drive.
Do you have a FW hard drive? Can you copy files from iBook to FW and then from there to iMac?
And, it is always nice to have a FW emergency/backup hard drive. The iMac needs a different partition scheme to be bootable from FW than the iBook does, but you can create the proper partition type etc from a Tiger Installer and put OS X on FireWire, then see if you can backup and repair your iMac's hard drive.
MicroMat's TechTool Pro 4.5.1 is now shipping and is compatible, Universal Binary and bootable. Always good to have some 3rd party utility handy.
If you are just starting out, you probably don't have much if anything installed yet, so you may want to just erase your iMac drive and restore to what it was. That would be the easiest if Disk Utility won't repair it.
Instead of powering off the iBook, I would have tried to force quit whatever was running, like Migration Assistant. -
Hey i bought a brand new MBP like 6 months ago and now it won't charge
i bought a brand new MBP like 6 months ago and now it won't charge. I tried using a friends MBP charger of the same year as my computer but it still says not charging at the top right corner of the computer screen where the charging symbol is. This problem just happened out of nowhere because it was working the day before then the next day it just stopped working saying it is not charging. I tired doing all of the suggested techniques to fix it but not luck.
This is the battery report is when my MBP is either connected to my charger or my friends charger which works perfectly on her computer.
Battery Information:
Model Information:
Serial Number: W013*****3BA
Manufacturer: SMP
Device Name: bq20z451
Pack Lot Code: 0
PCB Lot Code: 0
Firmware Version: 201
Hardware Revision: 000a
Cell Revision: 158
Charge Information:
Charge Remaining (mAh): 3137
Fully Charged: No
Charging: No
Full Charge Capacity (mAh): 5751
Health Information:
Cycle Count: 126
Condition: Normal
Battery Installed: Yes
Amperage (mA): 0
Voltage (mV): 11528
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 10
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 10
Wake on AC Change: No
Wake on Clamshell Open: Yes
Wake on LAN: Yes
Current Power Source: Yes
Display Sleep Uses Dim: Yes
PrioritizeNetworkReachabilityOverSleep: 0
RestartAfterKernelPanic: 157680000
Standby Delay: 4200
Standby Enabled: 0
Battery Power:
System Sleep Timer (Minutes): 10
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 2
Wake on AC Change: No
Wake on Clamshell Open: Yes
Display Sleep Uses Dim: Yes
Reduce Brightness: Yes
RestartAfterKernelPanic: 157680000
Standby Delay: 4200
Standby Enabled: 0
Hardware Configuration:
UPS Installed: No
AC Charger Information:
Connected: Yes
ID: 0x0000
Wattage (W): 0
Revision: 0x0000
Family: 0x0000
Serial Number: 0x00000000
Charging: No
As you can see where it is labeled "AC Charger information" it states that its connected but there is no Wattage and says its not charging .
What is wrong with my mac? Is it serious and does Apple Care cover it?Have you done a SMC
http://support.apple.com/kb/HT3964
Items include
Power
The computer doesn't respond to the power button when pressed.
A portable Mac doesn't appear to respond properly when you close or open the lid.
The computer sleeps or shuts down unexpectedly.
The battery does not appear to be charging properly.
The MagSafe power adaptor LED doesn't appear to indicate the correct activity. -
Hi, I have a brand new imac which i got today and when I open Iphoto all i get is the error message "Your photo library is either in use by another application or has become unreadable" any ideas? thanks
Are there photos in the Library? If not then just trash it and launch iphoto. It will make a new one.
If there are pics in it then Download iPhoto Library Manager and use its rebuild function. This will create a new library based on data in the albumdata.xml file. Not everything will be brought over - no slideshows, books or calendars, for instance - but it should get all your albums and keywords back.
Because this process creates an entirely new library and leaves your old one untouched, it is non-destructive, and if you're not happy with the results you can simply return to your old one. -
I bought my Macbook Pro OS X Lion 10.7.5 in january 2012 brand new from my local apple store and i am sure they said that it would run AIRPLAY. Having just purchased apple TV and set it all up correctly I still can't connect - no AIRPLAY symbol ? pls help
Mark
You need OS X 10.8 mountain lion, mirror is a feature of that OS and you need to buy it from the app store, OS X 10.7.5 does not do it.
If you don't want to change visit www.airparrot.com a third party app that can do it.
Jules -
Hi. For some reason my iPhones sound for all ring tone, lock, music loudspeaker has become very foamy and can hardly hear it. Both speakers are still working however just at low sound. In settings volume is turned up and bottons on the side are fully up.?
maybe there are dirt, sand and lint in the speaker output grill ?
-
Brand-New Empty Power Mac G5 Tower Cases for Sale???!!!
Have you heard that brand-new empty Power Mac G5 tower cases are available for sale? They are available in several cities in China for about 90 USD:
http://img5.pcpop.com/ArticleImages/500x375/0/337/000337034.jpg
http://img5.pcpop.com/ArticleImages/500x375/0/337/000337030.jpg
I am shocked~By the time you pay shipping from China it will cost as much or more than purchased in the USA.
BTW
I get my G5 cases from 1-800-WE-FIX-MACS via eBay auction and generally pay $50.00 + $40.00 shipping = $90.00
Maybe you are looking for
-
I want to know how to create a new script that can be run in batch proces in Photoshop Element 11 ?
-
Using variables as table names. Ideas for alternative designs
Hi, I am designing an application which uses synonyms to pull information from 'client' DBs via DB Links. The synonyms are created with a DB_ID in the name (example: CUSTOMER_100, CUSTOMER_200... where 100 and 200 are DB IDs from 2 separate client DB
-
Why do I have sound only in one headphone, stereo and docking station?
Why do I have sound only coming out of one side of headphone, car, stereo and docking station when playing itunes?
-
"operation terminated unexpectedly" during Outlook calendar synch
Help! Everything was synchronizing fine but then one day, just stopped working. I rec'd an error message from "Intellisync" stating "The operation terminated unexpectedly". I've tried to uninstall the DM software & reinstall several times but that
-
Three State Workflow (assigned to field)
I use the 3 State WF in a library. First and second task were assigned each to a person from 1 of 2 list fields of the library. But after first person completes the task and second task is created the person from second list field ist inserted in fir