MacBook Air "dead," 3 beeps on turn-on, dark screen

Pushing the power switch just gives repeating 3-beeps. If I hold the power button down it stops. Nothing on the screen. Any tips to resurrect it, or do I need to take it in to a store?
Before it "bricked," within a few hours, twice it froze and I saw a message on screen saying I need to hold the power button down to stop the machine, then press it to turn it on again.
It's a MacBook Air, 13", purchased January 2012.
Thanks for any tips.

Took it in, they did some tests and replaced the logic board. They had to order it so it took a few days, but it works now. Tnx.

Similar Messages

  • Because my new macbook air is so slow to turn off

    because my new macbook air is so slow to turn off

    Reset SMC.     http://support.apple.com/kb/HT3964
    Choose the method for:
    "Resetting SMC on portables with a battery you should not remove on your own".

  • HT4718 My macbook air is stuck at the "installing software updated" screen while installing update for the osX. What should I do?

    My macbook air is stuck at the "installing software updated" screen while installing update for the osX. What should I do?

    Welcome to Apple Support Communities
    If your Mac has been installing software updates for a long time, Software Update is probably frozen. Hold the Power button until your MacBook Air turns off, and turn it on again. OS X should start up.

  • My macbook air won't get past the white apple screen.  I've tried power cycling the batter but won't help

    my macbook air won't get past the white apple screen.  I've tried power cycling the batter but won't help

    Take each of these steps that you haven't already tried. Stop when the problem is resolved.
    Step 1
    The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
    There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
    a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
    b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
    c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
    d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
    Step 2
    If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
    Step 3
    Sometimes a startup failure can be resolved by resetting the NVRAM.
    Step 4
    If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
    Step 5
    If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
    Step 6
    Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
    Step 7
    If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
    Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
    Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
    The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
    If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
    If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
    Step 8
    Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
    This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
    Step 9
    If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.  
    Step 10
    Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
    Step 11
    Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
    Step 12
    This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
    Step 13
    If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

  • When I open my MacBook Air the keyboard comes up along with the screen and does not stay still?!

    When I open my MacBook Air the keyboard comes up along with the screen and does not stay still. So I need to hold down the keyboard while i open it. Other than that it works fine despite the fact that the fan noise some times is loud and sometimes it's getting warm at the base. I wonder if this can be fixed if i go to one of the apple branches.

    Yes. Take the computer to the Apple store to have it fixed.
    Best

  • I have a MacBook Air, it automatically minimises and switches from the screen I am in for some reason ?

    I have a MacBook Air, it automatically minimises and switches from the screen I am in for some reason ?

    This problem is often caused by "Google Drive." If it's installed, I suggest you first check for an update. If that doesn't solve the problem, remove it according to the developer's instructions. You may need to boot in safe mode to do so. Back up all data before making any changes.
    If you use Google Drive and don't want to remove it, then try deselecting the option in its preferences to "show status icons." According to reports, that may be enough to stop the Finder from crashing.

  • 10.5.2 killed my MacBook Air DEAD.

    10.5.2 completely killed my MacBook Air.
    i just installed the 10.5.2 update from the 343MB Combo updater downloaded from Apple. installation went fine... clicked to restart... showed the "need to update boot caches" window/warning. clicked "okay". it continued and went to the blue screen with the spinny wheel. then rebooted.
    went to a grey screen... and nothing else. no Apple. no spinny wheel. nothing.
    left it there for a good 20 minutes. no hard drive noise. nothing was happening.
    powered it up again. grey screen. nothing happens. no Apple. no "no" symbol. no anything.
    restarted with D to try out that new built-in hardware test. NOTHING.
    restarted with "option" to get the bootloader screen. NOTHING.
    restarted with apple-V... obviously it wasn't even getting that far. so still NOTHING.
    restarted with the PRAM reset combo. at least i got the chime. did it 3 times. then... NOTHING. grey screen still.
    restarted with the SMC reset key-combo. got the chime... then NOTHING. grey screen.
    i have run out of key combinations to try. and the machine is functionally dead.
    normally at this point i'd try a "T" and mount it on another machine to see what is going on. but... this is a MacBook Air.
    anyone have any ideas? this is beyond frustrating.
    thanks.

    beesleep wrote:
    looks like the 10.5.2 update was just highly highly coincidental. definitely seems odd the logic board would die at the exact instant of a restart from installing 10.5.2.
    When a light bulb files, it's usually fails when it is turned on. Ditto for most electronic devices. Whether it's a surge or whatever, it's probably true that your logic board would have failed when you started the computer up for whatever reason. There is no evidence that software can damage hardware directly, or at least instantly. Besides, the update should not have any effect on the computer until the boot process is well under way.
    Bad software might cause a computer to overheat, etc., but not to damage a component on boot.

  • Macbook Air - Dead Pixel

    I bought my early 2014 Macbook Air a little over 4 weeks ago, and I have just noticed a dead pixel in the middle of the screen. Will Apple fix this for free? I didn't buy my Macbook at an Apple shop, but at an authorized Apple retailer, so should I take it back to them for repair? Needless to say i'm a little frustrated with paying £1000 for a laptop to have a considerable sized dead pixel in the screen.

    Will Apple fix this for free?
    Only Apple can determine that. Read:
    About LCD display pixel anomalies for Apple products released in 2010 and later

  • Macbook air dead

    MAcbook air won't start, yosemite. It is completely dead. Smc and pram don't work. Yesterday it was fine, i left it asleep.

    Keep it charging for at least 12 hours.
    Reset SMC again.
    If that doesn't help, contact Apple.
    Genius Bar reservation
    http://www.apple.com/retail/geniusbar/
    Best.

  • Macbook air late 2012 won't turn on - Shows blinking no folder icon

    Hello,
    I bought my Macbook air in October 2012. Last night I tried updating my OS but the computer froze and I had to force restart it in the middle of the download. When I attempted to turn it on again it shows the blinking folder with a question mark on the white screen. It took around a minute for it to appear after the startup chime. I tried starting my Mac holding the option key and the only drives available are the internet recovery drive.
    Please help me!
    Thank you for every answer!

    Check  the Software update and run it if one is available.
    If available, install the update.
    MacBook Air SSD/Flash Storage replacement Program.
    "Apple has determined that certain 64GB and 128GB flash storage drives used in the previous generation of MacBook Air systems may fail. These systems were sold between June 2012 through June 2013."
    http://www.apple.com/support/macbookair-flashdrive/

  • 10.6.5 installed, MacBook Air dead after restart

    I've just seen a report that somebody killed his MacBook Air with the 10.6.5 update. How does that happen? Is the upgrade safe to install? The report was on trick77.com

    I (tried to) update to 10.6.5 on my Macbook Air 11.6" last thursday evening. *Sadly this resulted in the death of the machine*. Despite being connected to mains through out the machine never restarted after the install. *Pressing the power button does absolutely nothing*.
    I took it in to the 'Genius Bar' the following morning. The 'genius' told me there was nothing that could be done. A replacement is on its way.
    Luckily i had everything backed up so haven't lost any data but it is still a major inconvenience. Because mine was a custom spec (4GB ram instead of 2GB) they were unable to replace it in store - i have to wait probably a week an a half for it to be shipped and delivered.
    *_My advice:_ definitely do a full backup before updating to 10.6.5, but if were you i'd wait a while. There's a number of reports of this issue, and there's bound to be more over the coming days as more people attempt to install the update. You can live without 10.6.5 for a week or two, wait until more is known.*

  • My Macbook air (only 2 months old) has a black screen and I cannot see to get signed on, the keyboard seems to be on as I can see via having put on the Caps key which lights up and also the power cable when connected is at green how do I fix this?

    I have been faced with a Black screen this morning when I have gone to sign in/open my Macbook air this morning.  I can see that the keyboard seems to be on as the caps key when pressed is lighting up as is my charger cable link, however have noticed that the apple logo is not lit up.  Any thoughts?

    Try resetting SMC and NVRAP and then reboot.
    http://support.apple.com/kb/HT3964
    http://support.apple.com/kb/PH4405
    Try booting the Recovery Partition.  Power off, boot and then hold down the Command and R keys.  Is the screen still black?  If so it is not a software problem so take it in for diagnosis and repairs.  Make a Genius Bar reservation http://www.apple.com/retail/geniusbar/ or find an Apple Authorized Service Provider https://locate.apple.com/country .
    If you are running Mavericks try upgrading to 10.9.2.  It has a fix for black screen problems.

  • Installed new hdd in MacBook Air 2008, question folder and forbidden sign in screen, what to do?

    Hello
    I installed new hard drive to my MacBook Air 2008 and when I try to install lion/snow leopard/ mavericks it won't show up the disk. I can't find the hard drive.
    I don't now what to do. I tried everything. I spoke with a guy in macsupport here in Sweden and he said I have to buy snow leopard and install it from the original dvd in order for computer to format. My computer is old like I said its from 2008. I've never update it or upgrade. This is first time. It laid in storage for three years so I decide it to use it again but hdd was damaged so I had to change it, and now all I get is flashing question folder and forbidden sign, you know the sign for auto traffic.
    Is it true that the only way to restore or to find the new hdd or to boot the question mark and forbidden sign marks by installing osx from its original dvd or buy snow leopard?
    After I spoke with the guy from Mac support, I got little suspicious so I spoke to another one and he told me all I need to do is format hdd with the help of a sata hdd cable with help of another macbook and then I was good to go.
    What do u think?
    Should I buy snow leopard or can I burn it from my sister computer?

    I first would try Target Disk Mode to format and install an OSX on the new storage drive.
    http://support.apple.com/kb/ht1661
    You will need a OSX source that is compatible with the MBA.  If you have the original, use that.
    Ciao.

  • Macbook air will not boot 10.5.7 after screen replacement

    Hello
    Following screen replacement on original macbook air I can only take system to 10.5.6.  Will not update to 10.5.7 or 10.6.
    Any suggestions?
    GeorgeV

    BTW, I see the threads on the Thunderbolt update kernel panics.  I was kind of hoping Apple resolved the problem since I thought they had pulled the update.  Anyway, I do not *think* I am getting a Kernel panic as the boot does not even get as far as the Apple logo.  It just sits on the gray screen and does nothing.

  • MacBook Air, purchased 2011. Stuck on grey apple screen. Help!

    MacBook Air purchased in 2011, never had any trouble previously. Grey Screen stuck in thinking mode, will not accept any commands.  Have let battery drain and re charged but no difference. Any thoughts? Thanks.

    Being stuck at the grey screen generally means there's something wrong involving reading something from or writing something to the hard drive. Letting the battery die may be something that is sometimes useful for a phone or iPod, but never for a computer.
    Step 1: try restarting in Safe Mode. Reboot and when you hear the chime and/or the LCD backlight comes on press and hold the shift key until you see the Apple icon. The bootup will take longer than normal because the hard drive is being examined and repaired.  If this works you'll get to the desktop but Safe Mode only loads a minimal number of drivers so some things won't work. Reboot normally and see if you can get to the desktop now. If Step 1 failed or if after rebooting you returned to the gray screen try step 2.
    Step 2: try restarting in Recovery Mode. Reboot and when you hear the chime and/or the LCD backlight comes on press and hold the command and R keys. You should boot into a utility mode where you can a) check the hard drive directory and repair it if need be and b) download and reinstall the operating system and that's what you should try doing.
    If step 2 fails reboot holding option, command and R. This is Internet Recovery mode which is similar to Recovery mode except the drive will probably need to be formatted or partitioned before the OS can be reinstalled. This will erase all your data.
    And if this fails call AppleCare or make an appointment at the Apple store.

Maybe you are looking for