MB Pro won't recognize Canon i450 Printer

What can I do?

I have this printer and it works fine on my MBP. You have to first download the drivers from here:
http://www.usa.canon.com/consumer/controller?act=DownloadDetailAct&fcategoryid=3 31&modelid=8740
When you access that page, click on drivers and software, then scan down the list to the last one, it's the drivers for the Intel Macs and OS X.
And, then make sure the printer is not connected to your computer,install the drivers, and then after that, connect the printer and it should be recognized. If not you can do it manually.

Similar Messages

MacBook Pro won't recognize Canon MP800, even after reloading print drivers

Time Warner Cable updated servers. We had to update the DNS address for the MacBook Pro to maintain internet access. After doing this MacBook Pro doesn't recognize the Canon MP800 printer - shows no print drivers for Canon IJ Network , even after reinstalling printer software and downloading print drivers from Canon website - MPNavigator 2.0 keeps saying print driver has not installed. The MacBook is wirelessly networked with the printer and an EMac. We haven't updated the DNS address for the EMac because it still recognizes the printer and prints; however, we now don't have internet access with EMac as a result.

If printing wirelessly check your printer sharing settings - System Preferences/Sharing
If printer is connected directly to your computer, check your printer connections, read the troubleshooting section in your printer manual and check the printer manufacturer website for drivers you may need to update.

OSX 10.5.8 won't recognize Canon iP2702 printer

I just used the installation disc that came with my Canon iP2702 printer to install it on my Macbook w/10.5.8.    Canon says that the printer is compatible with Leopard in all of its literature.
I installed the driver that is on the disc, with the complete installation package. I followed the installation instructions to the letter.    The printer was not listed when I tried to print a document.
Then I went on Canon's site and downloaded the latest version of the driver. I installed it, but still the printer was not listed when I tried to print.   Nor was it listed when I tried to add a printer.
I rebooted the computer after the driver installation.   Still nothing.
Am I missing something?
Any tips greatly appreciated.

Hi David,
Try this for a start...
Mac OS X: About the Reset Printing System feature ...
http://support.apple.com/kb/HT1341?viewlocale=en_US
10.5/10.6/10.7/10.8 instructions...
In System Preferences>Fax & Print, Right click or Control+click on the Printers list Sidebar, choose Reset Printing System.
if you hold option and click the "-" tab it resets the printing system.
http://www.macosxhints.com/article.php?story=20031215144430486
Safe Boot from the HD, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions.
Any devices that previously appeared in your Printer List and Fax List will need to be added again after resetting the printing system.
Resetting the printing system in Mac OS X 10.5.x+++
To use the Reset Printing System feature in Mac OS X 10.5.x, follow these steps:
Choose System Preferences from the Apple menu.
Choose Print & Fax from the View menu.
Control-click on list of printers on the left side of the window, then choose "Reset printing system" from the contextual menu. If you don't see a list of printers, Control-click on the text "Click + to add a printer or fax" and select "Reset printing system..."
As an alternative, if you currently have one or more printers listed, you can Option-click the "-" (Remove printer) button.
http://support.apple.com/kb/ht1341
Reboot.

My MacBook pro won't recognize hard drive I put in it. It boots only to a white screen unless I boot to my recovery USB. If I do that then I can select my USB and my external time machine drive in the disk utility, so no problems there. But what do you

My MacBook pro won't recognize hard drive I put in it. It boots only to a white screen unless I boot to my recovery USB. If I do that then I can select my USB and my external time machine drive in the disk utility, so no problems there. But what do you think it is? It won't recognize any hard drive I put in the machine, so might it be the sata cable?

Boot the Recvoery USB, use Disk Utility to select the internal drive makers namea and size on the left.
Now select erase and select the midde option and click erase, it will take a bit to complete but it's best for the drive.
Now select Partiton tab, click the big box and Options: GUID and then Format: OS X Extended journaled and click apply.
Quit and you should be able to install OS X now with your Apple ID and password.
see
http://osxdaily.com/2011/08/08/lion-recovery-disk-assistant-tool-makes-external- lion-boot-recovery-drives/

MacBook Pro won't recognize 1TB external drive

Hey team,
My mid-2010 MacBook Pro won't recognize my WD My Passport 1TB drive. I was copying files from the drive to my computer when my computer went to sleep (didn't run out of power, just went to standby mode). Turned computer back on and now it won't recognize the drive.
It is a USB 3.0 cord (computer is only USB 2.0 and the cord works with other drives) and when plugged in, the light turns on and the disk spins but isn't recognized my this or other computers (also not in Disk Utility).
Tried a handful of disk recovery programs but nothing wants to 'see' the disk plugged in.
Thanks for any and all suggestions.

yes yes yes, I warn people about WD drives on this link:
Your dead external hard drive is likely fine! Great hope for your 'faulty' external HD
theReKleiner wrote:
What now?
Only option is to buy the SAME exact HD and swap controller boards, or pay someone a LOT more $$$ to do the same thing.
its not soldered there, its just a controller/ SATA "one piece"
They do that to save 50 cents in mfg. costs.
I mention your "issue" in that link. Which is why you do NOT buy WD ext. HD.
they make the controller board and SATA card one piece.
CURRENT MFG. THAT HAVE controller board and SATA cards as one piece are : WD USB drives, and Toshiba USB Canvio
However Toshiba didnt USED to do that, but they started doing it at the end of 2013.
avoid those 2.
To avoid that nonsense, buy Hitachi drives in USB.
Or, the best option:
Save money and invest in a bare hard drive backup and redundancy plan
Its cheaper
less fuss
more reiable, removes the nasty failure point of SATA card interfaces.
takes up lot less space.
Bare hard drives and docks. The most reliable and cheapest method of hard drive data storage, archives, and redundancies
The best method for your data archives and redundancies, which is also the least expensive, the most reliable, and the most compact option is the purchase of naked hard drives and at least one USB 3.0 HD dock ($40 roughly).
While regarding Time Machine and your Macbook or desktop, your primary backup is best saved to a conventional USB (or Firewire / thunderbolt) hard drive inside an enclosure, the most important part of your data protection begins after your 1st / primary Time Machine / backup; and these are your secondary (most important) data storage devices, archives and their redundancies.
However bare hard drives and docks (below) also work perfectly as a Time Machine backup, this is for home use, since the docking station is certainly not very portable as a notebook Time Machine backup device should be; nor should bare HD be packed around with a notebook, rather remain at home or office.
Six terabytes of 2.5" HD pictured below in a very compact space.
Bare hard drives and docks have the lowest cost, the highest reliability, and take up the smallest storage space
Drawbacks:
1. Care and knowledge in general handling of naked hard drives (how not to shock a bare HD, and how to hold them properly). Not a genuine drawback.
Advantages:
1. By far the least expensive method of mass HD storage on a personal basis. Highest quality naked HD can be purchased in bulk very cheap.
2. Eliminates the horrible failure point of SATA bridges and interfaces between external drives and the computer.
3. Per square foot you can store more terabytes of data this way than any other.
4. Fast, easy, no fuss and most simplex method of data storage on hard drives.

My phone won't recognize my thumb print

I charaged my phone overnight and now this morning it won't recognize my thumb print and the salesperson at Verizon didn't set up a pin number for me.

Hi dafrey44,
You may want to use this article to help you troubleshoot this issue with your Touch ID sensor:
iPhone 5s: Using Touch ID
http://support.apple.com/kb/HT5883
Thanks for being a part of the Apple Support Communities!
Regards,
Braden

Still no joy for Canon i450 printer

Print problems with update
this page is my test page
printing with Safari
http://news.yahoo.com/s/ap/us_cisco_restructuring
Canon i450
prints the framework but not the article
not fixed with first update
not fixed with second update
Canon mp560
fixed with first update
not broken with second update thank god
paranoid pat smells an abode rat
anybody get their i450 to print

I was just about to tell you the black tank was ok
when it sunk in that maybe all that was being printed was color.
So tried test page, nothing to compare to, but something printed, looked black.
Tried to clean nozzle, no joy.
Pages printed nothing but a blank sheet of paper.
Tried to deep clean nozzle. no joy.
So I thought maybe go back to basics and put a few lines in textedit
and throw in a line of red font just for fun.
I saw red and nothing else.
I had a black cartridge at hand
so I thought I would try.
And, as you diagnosed, the old cartridge was dead
Long live the new cartridge.
and thank you very much

Mac Pro won't recognize ethernet connection

My Mac Pro won't recognize the Ethernet cable when it's plugged in. I know the cable and connection are good because my MacBook Pro recognizes it with no problem. I've had it for around a year, but have always used the airport to connect to the internet. It has two Ethernet ports on the back and I've tried both. Is there anything I need to do to configure the NIC card?
Thanks in advance!
Ryan

No, but you do need to configure the Ethernet port in Network preferences. Open Network preferences and select the Ethernet port. Click on the Advanced button then on the TCP/IP tab. Set the Configure IPv4 drop down menu to DHCP. Set the Configure IPv6 drop down menu to Off. Click on the Apply button. If all is well you should see a valid IP address in the network settings for the port. If you see an IP address starting with 169., then it means your Ethernet port is not getting an IP address from your router. You should have an Ethernet cable connected from the Ethernet port on the computer to one of the LAN ports on your router.

After installing 10.9.3 computer won't recognize Canon SD 1200 IS camera: get message "a camera was not detected". Any suggestions?

After installing 10.9.3 computer won't recognize Canon SD 1200 IS camera: get message "a camera was not detected". Any suggestions?

I have an older Kodak which they have stopped supporting and I have to take out the SD card and put it in the card slot to download pictures. I read other threads where this solved similar problems for others. Some have a separate card reader but I just use the one on my imac. Wish it was more convienent to get to it though.

Acrobat 9 Standard won't recognize Canon Lide 200 Scanner

My recently installed Acrobat 9 Standard won't recognize my Canon Lide 200 scanner even though Adobe Photoshop CS2 does. I don't know what the problem is and how to solve it.

Adobe Acrobat Pro 9 was recently installed on new Vista 64bit computer and functions with all programs and even prints to my Dell 1600n printer, but when I try to scan from the printer, it causes this error message and shuts Acrobat down:
"ADOBE ACROBAT HAS STOPED WORKING A Problem has caused the program to stop working correctly. Windows will close the program and notify you if a solution is available."
I have lived with this since I bought the computer a month ago. Still no solution from Adobe and no response to an email that I sent to adobe support.

OS X 10.6.4 won't recognize Canon Powershot sd1000

I'm running OS X 10.6.4 on a Macbook pro, and it won't recognize my Canon powerbook sd1000 digital camera. I've updated the software, to no avail. Other cameras work too. I understand that I can move the card to a reader or another scanner; any tips on how to solve this problem directly?

I had the same problem at first. There is a switch on the back right side of the camera that selects camera, video, or playback. Switching it to playback caused it to be recognized by OSX.

HP Envy 5530 - computer won't recognize that the printer is on the same network

Product Name: HP ENVY 5530
OS: Windows 8.1
No changes made to system before issue occured
I bought this wireless printer last week (5-13-14). I have a working printer that was connected to my husband's work laptop via USB cable, but needed one to connect to our family computer, which is in a different room with the modem/router. My husband travels for work, so I want to be able to print without disturbing him and while he is away on business. I turned the printer on and connected it to my network with the password and printed out the network settings and the wireless report. There are about 8 other wireless networks in range of my printer (we're in a residential neighborhood), but we aren't having a problem with it connecting to someone elses stuff. I went online to download the driver software and it downloaded fine. I clicked on the desktop icon to launch the control panel for the printer and it opened up for me to install the printer. I went through every step and it won't recognize the IP address or the name of the printer, and therefore won't open up for me to do any scanning. Both the printer and PC are connected to the same network, but they won't recognize each other when it comes to going through the HP software to scan or print. I can go into word or something to print and it will let me print wirelessly, but it won't do anything from the control panel of the print software because it thinks the printer hasn't been installed. I've had Windows 8 on this computer since I bought it in 2012, but I have the computer defaulted to go to my desktop instead of the start screen, so I don't know if that makes a difference. I am going to go ahead and remove the device and uninstall everything so I can try again later. If I had known this was going to be a problem, I would have not bought the printer and just kept on doing what we'd been doing.

Hello SarahD_07,
Welcome to the HP Support Forums!
I understand you are having some troubles getting the Envy 5530 printing wireless on Windows 8.1. Are you able to take the I.P address of the 5530, type it into the address bar of your web browser and hit enter. Does it load a page about the printer?
Run the Print and Scan Dr to see if it can clear up the scanning issues if you can view that above page.
I will look out for your reply,
JERENDS
I work on behalf of HP
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

Yoga 2 Pro won't recognize my Seagate external hard drive

I have a Yoga 2 Pro that won't recognize my Seagate Backup Slim 2TB USB 3.0 external hard drive.
I ordered one from Amazon and it didn't recognize immediately when I plugged it in. The disk drive shows up in Devices and in Device manager with the Yellow caution triangle, but it never shows up in drives under my computer or in Disk Management (Where you change partitions, etc.)
So I ordered a replacement from amazon, I thought it was broken. I had tried it in a different computer and the same thing happened so I assumed it was the drive. On a whim I tried it on the alternate machine again except this time I bypassed the USB hub and plugged it directly into USB 2.0, it worked!
I installed a Paragon HFS+ software (it's for Mac Only Seagate drives to work with windows, even though this drive is NOT Mac only) and the installation failed, and my computer started messing up. It wouldn't completley power off nor restart. It just hung at the shutting down screen indefinitely.
Finally, I let the computer die, turned it back on, plugged in the hard drive and it worked. But I had already ordered the replacement. So I had to return the original and go tthe replacement and now it won't read at all.
Since I plugged it in, my computer will NEVER shut down, it will just sleep unless the battery dies, it won't restart either, it'll just hang at the restarting screen.
The drive still won't work, and the touchscreen doesn't work sometimes after a reboot. (Because I have to force shut it off everytime I want it off.)
I went into power settings and turned everything on max power (To help my battery die faster) and even changed the USB power option thing to disabled. I still don't know how I got it to work that ONE time and now I'm stuck. Any help or advice?

Oh I also had a message that came up when I tried to reconnect it to my comptuer. This is what the message stated:
The disk you inserted was not readable by this computer.
and my only options I have are
Initialize..., Ignore, Eject
what are my options of getting my data restored? I don't care so much about the drive, I am concern about my 2TB of data on there. Please anyone help me with this!!!!! I am open to suggestions to get my data back.

Please can anyone help. I am trying to reconect wirelessly my Macbook pro laptop to a canon mp600r printer ?

HI.Can anyone help please. I'm trying to wirelessly reconect my Mac book pro laptop to my canon mp600r wireless printer. I had it working once but after having secured my linksys router ( set a password ) it no longer conects wirelessly but it works with a cable.

You need to run through the wireless network connection wizard on the printer. Try looking under Menu or Setup choices on the printer's LCD. It should be no different than what you did initially with it, except this time when you pick your WIFI network from the available list, it'll ask you for a password, at which point you type in what you set it up when you secured your network. Once you've done that, your laptop will see it again... you shouldn't have to reload any drivers or add it back on, it'll just see it again since it's just the network connection that's broken.
BTW, I hope you chose to secure your WIFI network with WPA2/AES encryption. If not, you might as well take the time now and just reconfigure it again to secure it with that and then fix your printer connection. It's the most secure.

Laserjet Pro P1606dn running on a dell using XP Pro won't hold the default printer setting

Laserjet Pro P1606dn printer
OS is XP Pro
set it as the default printer but that setting keeps changing
How to fix this?
thanks

Yes, you need your own copy of WinXP (I used the one that came with VPC) but I'm afraid I have some good news/bad news to report. The good news is that WinXP does run a bit faster than VPC did on my dual processor G4 - the bad news is that XPs hardware detection DOES NOT - and I could find no way t force it - to recognize any USB or Firewire devices. Because I use Windows primarily to connect to USB GPS devices, this was a real letdown (and would be to users who need to, oh, I don't know, PRINT from Windows).
I'd love to hear from anyone has Windows actually functioning under OpenOSX Wintel - the website only goes as far a getting it to install and running Explorer (which I was able to do). I also had numerous keyboard problems: sometimes Windows would accept no input from the keyboard, sometimes it would reverse the caps lock key (on produced lowercase letters, off all uppercase). It also does not recognize the Apple Mighty Mouse as a two-button mouse. A number of these problems were - somehow - fixed by VPC which I never had a problem with when it came to USB devices (at least it DOES recognize a 'network card' and I can use Internet Explorer - whoopee!).
I'm going to play with this some more before throwing in the towel but I'm not so certain that I'm going to work towards the dual boot solution until I hear that Windows and Windows apps actually function - like being able to print or recognize a USB device.
Just getting Windows to install and run is of little good if it doesn't actually provide simple functionality.
I may copy and paste my original post in the Windows compatibility forum - see if any of those folks have found a working solution,

MB Pro won't recognize Canon i450 Printer

Similar Messages

Maybe you are looking for