MBSSID Issue
I have several 1130AG LWAPP's running 12.4(13d)JA connected to a contoller running 5.0.148.
2 SSID's are broadcast - usually no problem.
However, I've noticed that several different vendor wireless cards cannot see both SSID's.
Running a wireless capture, I can see that in reply to my probe request, I receive 2 probe responses. The only difference between the two 802.11 frame bodies is that for the SSID that I cannot see there is extended channel switch announcement (ECSA) information.
I'm slight confused as 1.) The SSID's are on the same antenna so shouldn't ECSA be on both beacon reponses? 2.) ECSA profile on 802.11b/g is wmm - wmm is disable both WLAN's.
I'm not sure changing Auto RF will make much difference. The Power and Channel settings are fine.
We use WZC.
I can solve the issue by upgrading internal users drivers. Specifically Intel 4965AG driver 11.1 to 11.5 - but the release notes don't imply any changes that are related to my problem and I'm reluctant to force this on 300+ people without a solid conclusion.
However I have no control over external guests WIFI drivers. So far its been a 50-50 hit/miss of them seeing the 2nd SSID (our GUEST ssid).
I'm sure its an 11n option but they are def. disabled on the WLC.
Similar Messages
-
Lan connectivity Issue on autonomous AP with throttles
Hello,
I encounter a strange problem on several AP 1242 in version 12.4(25d)JA1 of a customer :
He has 10 autonomous AP covering a factory and is using them for laptop connectivity and TOIP with mainly 7921 Cisco Wifi Phones.
The phones are configured to use only 802.11a.
The APs loose LAN connectivity randomly and therefore the clients don't work anymore.
The AP are connected on a 2960 and a 3560 wich are in turn connected on a 3750 wich route the trafic.
After checking spanning-tree no loops are present.
When I check the counters on the AP involved I see the "trhottles" and "ignored" counters incrementing on the fa0 link of the AP impacted wich mean I think it can't handle the incoming traffic. This incoming traffic seems not to be too big however. I can see drops on the switch interface connecting the AP.
There is a lot of roaming on the AP due to people walking in the factory with their wifi phones.
Here is a view of the fa0 counters :
AP1242-LOGIST#sh int fa0
FastEthernet0 is up, line protocol is up
Hardware is PowerPCElvis Ethernet, address is 001d.a1ce.26e2 (bia 001d.a1ce.26e2)
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Full-duplex, 100Mb/s, MII
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/160/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 81000 bits/sec, 53 packets/sec
5 minute output rate 29000 bits/sec, 26 packets/sec
7447113 packets input, 674891974 bytes
Received 286839 broadcasts, 0 runts, 0 giants, 549631 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 549631 ignored
0 watchdog
0 input packets with dribble condition detected
4422100 packets output, 609868806 bytes, 0 underruns
0 output errors, 0 collisions, 4 interface resets
1 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
Here is a small part of logs concerning roaming, i don't see errors or log indicating that something is wrong nor in the switches log :
Jun 6 12:57:27.007: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP001E4A3EE15D 001e.4a3e.e15d Associated KEY_MGMT[WPAv2 PSK]
Jun 6 12:57:42.499: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP588D09D3A92B 588d.09d3.a92b Reassociated KEY_MGMT[WPAv2 PSK]
Jun 6 12:58:02.620: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 588d.09d3.a92b Reason: Sending station has left the BSS
Jun 6 12:58:03.653: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP588D09D3A92B 588d.09d3.a92b Reassociated KEY_MGMT[WPAv2 PSK]
Jun 6 12:59:15.564: %DOT11-6-ROAMED: Station 588d.09d3.a92b Roamed to 001e.134c.5a50
Jun 6 12:59:15.564: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 588d.09d3.a92b Reason: Sending station has left the BSS
Jun 6 12:59:41.905: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 442b.0355.ab28 Reason: Previous authentication no longer valid
Jun 6 12:59:54.728: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP442B0355AB28 442b.0355.ab28 Associated KEY_MGMT[WPAv2 PSK]
Jun 6 13:01:12.541: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP588D09D3A92B 588d.09d3.a92b Reassociated KEY_MGMT[WPAv2 PSK]
Jun 6 13:02:35.841: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 001e.4a3e.d875 Reason: Previous authentication no longer valid
Jun 6 13:02:36.489: %DOT11-6-ASSOC: Interface Dot11Radio0, Station ec85.2f7c.c837 Associated KEY_MGMT[WPAv2 PSK]
Jun 6 13:03:29.256: %DOT11-6-ROAMED: Station 588d.09d3.a92b Roamed to 001e.134c.5a50
Jun 6 13:03:29.256: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 588d.09d3.a92b Reason: Sending station has left the BSS
Jun 6 13:04:32.754: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP001E4A3ED875 001e.4a3e.d875 Associated KEY_MGMT[WPAv2 PSK]
Jun 6 13:06:47.858: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 001e.4a3e.e15d Reason: Previous authentication no longer valid
Jun 6 13:07:18.107: %DOT11-6-ROAMED: Station 001f.6c7a.5101 Roamed to 001d.a2bb.15b0
Jun 6 13:07:18.107: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 001f.6c7a.5101 Reason: Sending station has left the BSS
Jun 6 13:07:38.109: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP588D09D3A92B 588d.09d3.a92b Reassociated KEY_MGMT[WPAv2 PSK]
Jun 6 13:07:42.031: %DOT11-6-ROAMED: Station 588d.09d3.a92b Roamed to 001e.134c.5a50
Jun 6 13:07:42.031: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 588d.09d3.a92b Reason: Sending station has left the BSS
Jun 6 13:07:46.489: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP001F6C7A5101 001f.6c7a.5101 Reassociated KEY_MGMT[WPAv2 PSK]
Jun 6 13:08:27.712: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP588D09D3A92B 588d.09d3.a92b Reassociated KEY_MGMT[WPAv2 PSK]
Jun 6 13:08:44.502: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 588d.09d3.a92b Reason: Sending station has left the BSS
Jun 6 13:08:44.572: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP588D09D3A92B 588d.09d3.a92b Associated KEY_MGMT[WPAv2 PSK]
Jun 6 13:08:56.778: %DOT11-6-ROAMED: Station 588d.09d3.a92b Roamed to 001e.134c.5a50
Jun 6 13:08:56.779: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 588d.09d3.a92b Reason: Sending station has left the BSS
Jun 6 13:09:17.874: %DOT11-6-ROAMED: Station 001f.6c7a.5101 Roamed to 003a.9a92.8d70
Jun 6 13:09:17.874: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 001f.6c7a.5101 Reason: Sending station has left the BSS
The AP are configured as follow :
Current configuration : 5184 bytes
! No configuration change since last restart
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname AP1242-LOGIST
logging rate-limit console 9
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
clock timezone gmt+1 1
clock summer-time gmt recurring last Sun Mar 2:00 last Sun Oct 3:00
dot11 syslog
dot11 vlan-name Data vlan 11
dot11 vlan-name Voix vlan 14
dot11 vlan-name Webguest vlan 5
dot11 ssid WLAN_data
vlan 11
authentication open
authentication key-management wpa
mbssid guest-mode
wpa-psk ascii 7 10600C0E261B173C252203797479633F371A29
dot11 ssid WLAN_voice
vlan 14
authentication open
authentication key-management wpa
mbssid guest-mode
wpa-psk ascii 7 080F49592A1500203B2D25567A7A7622263C0C
dot11 ssid Webguest
vlan 5
authentication open
mbssid guest-mode
dot11 wpa handshake timeout 1000
dot11 arp-cache
dot11 priority-map avvid
dot11 phone
power inline negotiation prestandard source
class-map match-all _class_voice0
match ip dscp ef
class-map match-all _class_voice1
match ip dscp cs3
policy-map voice
class _class_voice0
set cos 6
class _class_voice1
set cos 3
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 11 mode ciphers aes-ccm
encryption vlan 14 mode ciphers aes-ccm
ssid WLAN_data
ssid WLAN_voice
ssid Webguest
mbssid
power client 17
channel 2472
station-role root
dot11 qos class voice local
admission-control
admit-traffic narrowband max-channel 75 roam-channel 6
dot11 qos class voice cell
admission-control
no cdp enable
infrastructure-client
interface Dot11Radio0.5
encapsulation dot1Q 5
no ip route-cache
no cdp enable
bridge-group 5
bridge-group 5 subscriber-loop-control
bridge-group 5 block-unknown-source
no bridge-group 5 source-learning
no bridge-group 5 unicast-flooding
bridge-group 5 spanning-disabled
interface Dot11Radio0.11
encapsulation dot1Q 11
no ip route-cache
no cdp enable
bridge-group 11
bridge-group 11 subscriber-loop-control
bridge-group 11 block-unknown-source
no bridge-group 11 source-learning
no bridge-group 11 unicast-flooding
bridge-group 11 spanning-disabled
interface Dot11Radio0.14
encapsulation dot1Q 14
no ip route-cache
no cdp enable
bridge-group 14
bridge-group 14 subscriber-loop-control
bridge-group 14 block-unknown-source
no bridge-group 14 source-learning
no bridge-group 14 unicast-flooding
bridge-group 14 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
encryption vlan 11 mode ciphers aes-ccm
encryption vlan 14 mode ciphers aes-ccm
ssid WLAN_data
ssid WLAN_voice
ssid Webguest
no dfs band block
mbssid
channel dfs
station-role root
interface Dot11Radio1.5
encapsulation dot1Q 5
no ip route-cache
no cdp enable
bridge-group 5
bridge-group 5 subscriber-loop-control
bridge-group 5 block-unknown-source
no bridge-group 5 source-learning
no bridge-group 5 unicast-flooding
bridge-group 5 spanning-disabled
interface Dot11Radio1.11
encapsulation dot1Q 11
no ip route-cache
no cdp enable
bridge-group 11
bridge-group 11 subscriber-loop-control
bridge-group 11 block-unknown-source
no bridge-group 11 source-learning
no bridge-group 11 unicast-flooding
bridge-group 11 spanning-disabled
interface Dot11Radio1.14
encapsulation dot1Q 14
no ip route-cache
no cdp enable
bridge-group 14
bridge-group 14 subscriber-loop-control
bridge-group 14 block-unknown-source
no bridge-group 14 source-learning
no bridge-group 14 unicast-flooding
bridge-group 14 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
speed 100
full-duplex
no cdp enable
hold-queue 160 in
interface FastEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
no cdp enable
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface FastEthernet0.5
encapsulation dot1Q 5
no ip route-cache
no cdp enable
bridge-group 5
no bridge-group 5 source-learning
bridge-group 5 spanning-disabled
interface FastEthernet0.11
encapsulation dot1Q 11
no ip route-cache
no cdp enable
bridge-group 11
no bridge-group 11 source-learning
bridge-group 11 spanning-disabled
interface FastEthernet0.14
encapsulation dot1Q 14
no ip route-cache
no cdp enable
bridge-group 14
no bridge-group 14 source-learning
bridge-group 14 spanning-disabled
service-policy input voice
service-policy output voice
interface BVI1
ip address 10.17.10.5 255.255.255.0
no ip route-cache
ip default-gateway 10.17.10.254
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
logging trap warnings
logging 10.15.51.115
no cdp run
bridge 1 route ip
line con 0
line vty 0 4
sntp server 10.15.1.50
sntp broadcast client
end
Does someone ever experienced a similar problem ?
When I shut radio interfaces they're is no more problems on the LAN. Can this be an overlapping coverage issue ?
Can someone please give me advices on how to troubleshoot this issue ?
Thank you in advance as I'm a bit stuck.
Best Regards,Hi Scott,
Thanks for your reply.
Do you think this can be the origin of the issue my customer encounters or is it only to be standard ? As this change will have to be made on all clients, if there is a chance it solves the problem I will do it ASAP, if not I will delay it in a less busy period :-)
Can the constant roaming associations and dissasociations overload the AP and make it stop responding on the LAN or is it only a throuhput problem ?
Thanks in advance for your answer.
Best Regards, -
Trunking issue with autonomous AP
I was at a customers that wanted a new ssid configured on his 20 1252 AP's and to stand up a new one with the olds and new SSID on it. Added the vlans, trunked them down and configured the interfaces and SSID's on the existing AP's no biggie. The new AP(not really new been kicking around in a lab) is giving me some weird issues. I deleted the exisiting config from it and took one of the running configs fromm the others that are working, modified the name and ip and pasted it in. This should have worked just fine. However the trunk port on the 4507 will not come up. The radio's are up and so is the BVI, however I cannot ping to it since the trunk is down. I started looking at the config and the thing I notice is that the AP's are in vlan 2, and the native vlan is set for vlan 2 on all the working trunk ports on the switch. However the AP's do not have vlan 2 on them, and their native vlan is 1. This should not work! I always thought the native had to match on both sides?? In any case I am probably missing something stupid, I have been up since 4am it was a 4 hour drive to get here. Oh and I have to go back and make firewall changes at midnight. Here is the relavent configs please let me know if its something stupid I usually do a lot of controller based installs havnet done a autonomous one in years. Thanks!
Here is a port on the switch
interface GigabitEthernet3/9
description AP 1 - SMT
switchport access vlan 2
switchport trunk native vlan 2
switchport trunk allowed vlan 2,9,15
switchport mode trunk
end
Here is the AP hanging off that works fine
cstwap01#sh vlans
Virtual LAN ID: 1 (IEEE 802.1Q Encapsulation)
vLAN Trunk Interfaces: Dot11Radio0
Dot11Radio1
GigabitEthernet0
This is configured as native Vlan for the following interface(s) :
Dot11Radio0
Dot11Radio1
GigabitEthernet0
show run on the AP
dot11 mbssid
dot11 vlan-name VoIPVLan vlan 9
dot11 vlan-name Wireless-101-Legacy vlan 15
dot11 ssid 101
vlan 15
authentication open
mbssid guest-mode
dot11 ssid VoIPVLan
vlan 9
authentication open
mbssid guest-mod
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
ssid 101
ssid VoIPVLan
interface Dot11Radio0.9
encapsulation dot1Q 9
no ip route-cache
bridge-group 9
bridge-group 9 subscriber-loop-control
bridge-group 9 block-unknown-source
no bridge-group 9 source-learning
no bridge-group 9 unicast-flooding
bridge-group 9 spanning-disabled
interface Dot11Radio0.15
encapsulation dot1Q 15
no ip route-cache
bridge-group 15
bridge-group 15 subscriber-loop-control
bridge-group 15 block-unknown-source
no bridge-group 15 source-learning
no bridge-group 15 unicast-flooding
bridge-group 15 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface GigabitEthernet0.9
encapsulation dot1Q 9
no ip route-cache
bridge-group 9
no bridge-group 9 source-learning
bridge-group 9 spanning-disabled
interface GigabitEthernet0.15
encapsulation dot1Q 15
no ip route-cache
bridge-group 15
no bridge-group 15 source-learning
bridge-group 15 spanning-disabled
interface BVI1
ip address 10.190.2.51 255.255.255.0
no ip route-cache
ip default-gateway 10.190.2.1Hello Mike,
actually, native VLAN doesn't have to match on two sides of a trunk, in fact it's quite common with autonomous APs. Your BVI1 is usually tied to a native VLAN 1, but switch port native VLAN is usually configured for whatever VLAN you want AP's management IP to belong to, in your case VLAN 2.
When you connect two catalyst switches together with a trunk that has different native VLAN configured on two sides, you will keep getting logging messages warning you about it. It's not recommended, but some scenarios require such setup.
Something else is wrong, maybe a physical issue. When you say the trunk is down, do you mean the interface is down ? Can you paste config of bad switch port and bad AP?
Regards,
Roman -
QoS / Native VLAN Issue - Please HELP! :)
I've purchased 10 Cisco Aironet 2600 AP’s (AIR-SAP2602I-E-K9 standalone rather than controller based).
I’ve configured the WAP’s (or the first WAP I’m going to configure and then pull the configuration from and push to the others) with 2 SSID’s. One providing access to our DATA VLAN (1000 – which I’ve set as native on the WAP) and one providing access to guest VLAN (1234). I’ve configured the connecting DELL switchport as a trunk and set the native VLAN to 1000 (DATA) and allowed trunk traffic for VLAN’s 1000 and 1234. Everything works fine, when connecting to the DATA SSID you get a DATA IP and when you connect to the GUEST SSID you lease a GUEST IP.
The problem starts when I create a QoS policy on the WAP (for Lync traffic DSCP 40 / CS5) and try to attach it to my VLAN’s. It won’t let me attach the policy to VLAN 1000 as it’s the native VLAN. If I change VLAN 1000 on the WAP to NOT be the native VLAN I can attach the policies however wireless clients can no longer attach to either SSID properly as they fail to lease an IP address and instead get a 169.x.x.x address.
I'm sure I'm missing something basic here so please forgive my ignorance.
This is driving me insane!
Thanks to anyone that provides assistance. Running config below and example of the error...
User Access Verification
Username: admin
Password:
LATHQWAP01#show run
Building configuration...
Current configuration : 3621 bytes
! Last configuration change at 02:37:59 UTC Mon Mar 1 1993 by admin
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname LATHQWAP01
logging rate-limit console 9
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
no ip routing
dot11 syslog
dot11 vlan-name Data vlan 1000
dot11 vlan-name Guest vlan 1234
dot11 ssid LatitudeCorp
vlan 1000
authentication open
authentication key-management wpa version 2
wpa-psk ascii
dot11 ssid LatitudeGuest
vlan 1234
authentication open
authentication key-management wpa version 2
guest-mode
wpa-psk ascii
crypto pki token default removal timeout 0
username admin privilege 15 password!
class-map match-all _class_Lync0
match ip dscp cs5
policy-map Lync
class _class_Lync0
set cos 6
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 1234 mode ciphers aes-ccm
encryption vlan 1000 mode ciphers aes-ccm
ssid LatitudeCorp
ssid LatitudeGuest
antenna gain 0
stbc
station-role root
interface Dot11Radio0.1000
encapsulation dot1Q 1000 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.1234
encapsulation dot1Q 1234
no ip route-cache
bridge-group 255
bridge-group 255 subscriber-loop-control
bridge-group 255 spanning-disabled
bridge-group 255 block-unknown-source
no bridge-group 255 source-learning
no bridge-group 255 unicast-flooding
service-policy input Lync
service-policy output Lync
interface Dot11Radio1
no ip address
no ip route-cache
encryption vlan 1234 mode ciphers aes-ccm
encryption vlan 1000 mode ciphers aes-ccm
ssid LatitudeCorp
ssid LatitudeGuest
antenna gain 0
no dfs band block
stbc
channel dfs
station-role root
interface Dot11Radio1.1000
encapsulation dot1Q 1000 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio1.1234
encapsulation dot1Q 1234
no ip route-cache
bridge-group 255
bridge-group 255 subscriber-loop-control
bridge-group 255 spanning-disabled
bridge-group 255 block-unknown-source
no bridge-group 255 source-learning
no bridge-group 255 unicast-flooding
service-policy input Lync
service-policy output Lync
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
interface GigabitEthernet0.1000
encapsulation dot1Q 1000 native
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
interface GigabitEthernet0.1234
encapsulation dot1Q 1234
no ip route-cache
bridge-group 255
bridge-group 255 spanning-disabled
no bridge-group 255 source-learning
service-policy input Lync
service-policy output Lync
interface BVI1
ip address 10.10.1.190 255.255.254.0
no ip route-cache
ip default-gateway 10.10.1.202
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
transport input all
end
LATHQWAP01#conf
Configuring from terminal, memory, or network [terminal]? t
Enter configuration commands, one per line. End with CNTL/Z.
LATHQWAP01(config)#int dot11radio1.1000
LATHQWAP01(config-subif)#ser
LATHQWAP01(config-subif)#service-policy in
LATHQWAP01(config-subif)#service-policy input Lync
set cos is not supported on native vlan interface
LATHQWAP01(config-subif)#Hey Scott,
Thank you (again) for your assistance.
So I' ve done as instructed and reconfigured the WAP. I've added an additional VLAN (1200 our VOIP VLAN) and made this the native VLAN - so 1000 and 1234 are now tagged. I've configure the BVI interface with a VOIP IP address for management and can connect quite happily. I've configured the connecting Dell switchport as a trunk and to allow trunk vlans 1000 (my DATA SSID), 1200(native) and 1234 (MY GUEST SSID). I'm now back to the issue where when a wireless client attempts to connect to either of my SSID's (Guest or DATA) they are not getting a IP address / cannot connect.
Any ideas guys? Forgive my ignorance - this is a learning curve and one i'm enjoying.
LATHQWAP01#show run
Building configuration...
Current configuration : 4426 bytes
! Last configuration change at 20:33:19 UTC Mon Mar 1 1993 by Cisco
version 15.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname LATHQWAP01
logging rate-limit console 9
enable secret 5
no aaa new-model
no ip source-route
no ip cef
dot11 syslog
dot11 vlan-name DATA vlan 1000
dot11 vlan-name GUEST vlan 1234
dot11 vlan-name VOICE vlan 1200
dot11 ssid LatitudeCorp
vlan 1000
authentication open
authentication key-management wpa version 2
mobility network-id 1000
wpa-psk ascii
dot11 ssid LatitudeGuest
vlan 1234
authentication open
authentication key-management wpa version 2
mbssid guest-mode
mobility network-id 1234
wpa-psk ascii
no ids mfp client
dot11 phone
username CISCO password
class-map match-all _class_Lync0
match ip dscp cs5
policy-map Lync
class _class_Lync0
set cos 6
bridge irb
interface Dot11Radio0
no ip address
encryption vlan 1000 mode ciphers aes-ccm
encryption vlan 1234 mode ciphers aes-ccm
ssid LatitudeCorp
ssid LatitudeGuest
antenna gain 0
stbc
mbssid
station-role root
interface Dot11Radio0.1000
encapsulation dot1Q 1000
bridge-group 255
bridge-group 255 subscriber-loop-control
bridge-group 255 spanning-disabled
bridge-group 255 block-unknown-source
no bridge-group 255 source-learning
no bridge-group 255 unicast-flooding
service-policy input Lync
service-policy output Lync
interface Dot11Radio0.1200
encapsulation dot1Q 1200 native
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.1234
encapsulation dot1Q 1234
bridge-group 254
bridge-group 254 subscriber-loop-control
bridge-group 254 spanning-disabled
bridge-group 254 block-unknown-source
no bridge-group 254 source-learning
no bridge-group 254 unicast-flooding
service-policy input Lync
service-policy output Lync
interface Dot11Radio1
no ip address
encryption vlan 1000 mode ciphers aes-ccm
encryption vlan 1234 mode ciphers aes-ccm
ssid LatitudeCorp
ssid LatitudeGuest
antenna gain 0
peakdetect
no dfs band block
stbc
mbssid
channel dfs
station-role root
interface Dot11Radio1.1000
encapsulation dot1Q 1000
bridge-group 255
bridge-group 255 subscriber-loop-control
bridge-group 255 spanning-disabled
bridge-group 255 block-unknown-source
no bridge-group 255 source-learning
no bridge-group 255 unicast-flooding
service-policy input Lync
service-policy output Lync
interface Dot11Radio1.1200
encapsulation dot1Q 1200 native
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio1.1234
encapsulation dot1Q 1234
bridge-group 254
bridge-group 254 subscriber-loop-control
bridge-group 254 spanning-disabled
bridge-group 254 block-unknown-source
no bridge-group 254 source-learning
no bridge-group 254 unicast-flooding
service-policy input Lync
service-policy output Lync
interface GigabitEthernet0
no ip address
duplex full
speed auto
interface GigabitEthernet0.1000
encapsulation dot1Q 1000
bridge-group 255
bridge-group 255 spanning-disabled
no bridge-group 255 source-learning
service-policy input Lync
service-policy output Lync
interface GigabitEthernet0.1200
encapsulation dot1Q 1200 native
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
interface GigabitEthernet0.1234
encapsulation dot1Q 1234
bridge-group 254
bridge-group 254 spanning-disabled
no bridge-group 254 source-learning
service-policy input Lync
service-policy output Lync
interface BVI1
mac-address 881d.fc46.c865
ip address 10.10. 255.255.254.0
ip default-gateway 10.10.
ip forward-protocol nd
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
login local
transport input all
sntp server ntp2c.mcc.ac.uk
sntp broadcast client
end
LATHQWAP01# -
Cisco 877W Dual SSID/VLAN Security Issue
Hi All
I have an issue with my 877W that is as fascinating as it is frustrating. I have two SSIDs/VLANs, one for trusted LAN users (PRIVATE), and one for guests (GUEST). The PRIVATE network is secured from the GUEST nework by zone based firewall. Everything works fine, guest devices cannot access private devices, except for one thing - the BVI interface on the PRIVATE network is always accessible to guest devices, and all services open to attack eg telnet/ssh/http/dns etc. I've tried everything to secure this interface from the guest network, including putting deny any any on physical, BVI and VLAN interfaces
Am I missing something obvious, or some fundamental architecture of the 877 that would stop this interface being secured? Any help aprreciated!
P.S config has been pared down to basics below
version 15.1
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname ROUTER
boot-start-marker
boot-end-marker
logging buffered 4096
enable secret 5 $1$BdpF$r/mAhQGYs8LBlqEpANmke0
no aaa new-model
dot11 syslog
dot11 ssid PRIVATE@123
vlan 100
authentication open
authentication key-management wpa
wpa-psk ascii 7 046B0A535A15441D2D0C11141A5A5F
dot11 ssid VISITOR@123
vlan 200
authentication open
authentication key-management wpa
mbssid guest-mode
wpa-psk ascii 7 03374C0A08392040420C00
ip source-route
no ip dhcp conflict logging
ip dhcp excluded-address 172.16.1.1 172.16.1.10
ip dhcp excluded-address 192.168.0.1 192.168.0.10
ip dhcp pool GUEST
utilization mark low 70 log
network 172.16.1.0 255.255.255.0
dns-server 192.168.0.1 61.9.242.33 61.9.226.33
default-router 172.16.1.1
ip dhcp pool PRIVATE
utilization mark low 70 log
network 192.168.0.0 255.255.255.0
dns-server 192.168.0.1 61.9.242.33 61.9.226.33
default-router 192.168.0.1
ip cef
no ipv6 cef
multilink bundle-name authenticated
username cisco privilege 15 password 7 073F205F5D1E491713
policy-map type inspect PM-DENYGUEST
class class-default
drop
zone security GUEST
zone security PRIVATE
zone-pair security GUEST-TO-PRIVATE source GUEST destination PRIVATE
service-policy type inspect PM-DENYGUEST
bridge irb
interface ATM0
no ip address
shutdown
no atm ilmi-keepalive
interface FastEthernet0
no ip address
interface FastEthernet1
switchport access vlan 100
no ip address
interface FastEthernet2
switchport access vlan 100
no ip address
interface FastEthernet3
no ip address
interface Dot11Radio0
no ip address
encryption vlan 100 mode ciphers aes-ccm
encryption vlan 200 mode ciphers aes-ccm
broadcast-key vlan 100 change 30
broadcast-key vlan 200 change 30
ssid PRIVATE@123
ssid VISITOR@123
mbssid
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
interface Dot11Radio0.100
encapsulation dot1Q 100 native
zone-member security PRIVATE
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.200
encapsulation dot1Q 200
zone-member security GUEST
bridge-group 2
bridge-group 2 subscriber-loop-control
bridge-group 2 spanning-disabled
bridge-group 2 block-unknown-source
no bridge-group 2 source-learning
no bridge-group 2 unicast-flooding
interface Vlan1
no ip address
interface Vlan100
no ip address
bridge-group 1
interface Vlan200
no ip address
bridge-group 2
interface Dialer0
ip address negotiated
ip access-group 101 out
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap callin
ppp chap hostname [email protected]
ppp chap password 7 10580A4F1C4005005B
interface BVI1
ip address 192.168.0.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
zone-member security PRIVATE
interface BVI2
ip address 172.16.1.1 255.255.0.0
ip nat inside
ip virtual-reassembly in
zone-member security GUEST
ip forward-protocol nd
ip http server
ip http access-class 2
ip http authentication local
ip http secure-server
ip nat inside source list 1 interface Dialer0 overload
ip route 0.0.0.0 0.0.0.0 Dialer0
logging trap debugging
logging 192.168.0.11
control-plane
bridge 1 protocol ieee
bridge 1 route ip
bridge 2 protocol ieee
bridge 2 route ip
line con 0
exec-timeout 5 0
no modem enable
transport output all
line aux 0
exec-timeout 0 1
no exec
transport output none
line vty 0 4
exec-timeout 5 0
login local
transport input telnet ssh
transport output none
endIgnore that. self zone got me. Argh! phew!
-
Using MBSSID - new 1252 wireless APs not letting hosts connect
Solution:
After spending a few weeks working with Cisco in trying to figure out why new 1252 APs weren't getting a DHCP address from our Juniper SSG5 firewall (on different VLANs for each SSID), I finally got to a Cisco tech who knew the answer, so am posting it here to perhaps help someone else.
Using MBSSID, according to the first tech, only one can be in open authentication mode (e.g. no WEP, WPA, etc.) You can have multiple SSIDs that utilize the same method of authentication, just not more than one of them open.
Using MBSSID, on some wireless NICs that are apparently somehow sensitive to it, only one SSID can be in guest/broadcast mode. This ultimately was the solution to our connectivity issue.
It would be good to have documented what those NICs are that experience this problem.gcgeorge wrote:
Hi Fiedi,
Thanks for you reply.
The guests are both configured to use a bridged adaptor on the wireless adaptor.
I am currently using the rac1-priv IP address (192.168.0.101), and it does not work. If I try the public or VIP addresses, they do not work either - presumably since they are on a different subnet.
Thanks
Gavin
You will not be able to connect through private network as there isn't listener listening in that IP.
Try change your wireless IP to network 192.168.2.x and try to ping the guests public IP
Cheers -
New DVR Issues (First Run, Channel Switching, etc.)
I've spent the last 30 minutes trying to find answers through the search with no luck, so sorry if I missed something.
I recently switched to FIOS from RCN cable in New York. I've gone through trying to setup my DVR and am running into issues and was hoping for some answers.
1. I setup two programs to record at 8PM, I was watching another channel at the time and only half paying attention. Around 8:02 I noticed a message had popped up asking if I would like to switch channels to start recording. I was expecting it to force it to switch like my old DVR, but in this case it didn't switch and I missed the first two minutes of one of the shows. I typically leave my DVR on all day and just turn off the TV, this dual show handling will cause issues with that if I forget to turn off the DVR. Is there a setting I can change that will force the DVR to choose one of the recording channels?
2. I setup all my recordings for "First Run" because I only want to see the new episodes. One show I setup was The Daily Show on comedy central, which is shown weeknights at 11pm and repeated 3-4 times throughout the day. My scheduled recordings is showing all these as planned recordings even though only the 11pm show is really "new". Most of the shows I've setup are once a week so they aren't a problem, but this seems like it will quickly fill my DVR. Any fixes?
Thanks for the help.
Solved!
Go to Solution.I came from RCN about a year ago. Fios is different in several ways, not all of them desirable. Here are several ways to get--and fix--unwanted recordings from a series recording setup.
Some general principles.
Saving changes. When you originally create a series with options, or if you go back to edit the options for an existing series, You MUST save the Series Options changes. Pretty much everywhere else in the user interface, when you change an option, the change takes effect immediately--but not in Series Options. Look at the Series Options window. Look at the far right side. There is a vertical "Save" bar, which you must navigate to and click OK on to actually save your changes. Exiting the Series Options window without having first saved your changes loses all your attempted changes--immediately.
Default Series Options. This is accessed from [Menu]--DVR--Settings--Default Series Options. This will bring up the series options that will automatically be applied to the creation of a NEW series. The options for every previously created series will not be affected by a subsequent modification of the Default Series Options. You should set these options to the way you would like them to be for the majority of series recordings that you are likely to create. Be sure to SAVE your changes. This is what you will get when you select "Create Series Recording" from the Guide. When creating a new series recording where you think that you may want options different from the default, select "Create Series with Options" instead. Series Options can always be changed for any individual series set up later--but not for all series at once.
Non-series recordings. With Fios you have no directly available options for these. With RCN and most other DVRs, you can change the start and end times for individual episodes, including individual episodes that are also in a series. With Fios, your workarounds are to create a series with options for a single program, then delete the series later; change the series options if the program is already in a series, then undo the changes you made to the series options later; or schedule recordings of the preceding and/or following shows as needed.
And now, to the unwanted repeats.
First, make sure your series options for the specific series in question--and not just the series default options--include "First Run Only". If not, fix that and SAVE. Then check you results by viewing the current options using the Series Manager app under the DVR menu.
Second, and most annoying, the Guide can have repeat programs on your channel tagged as "New". It happens. Set the series option "Air Time" to "Selected Time". To make this work correctly, you must have set up the original series recording after selecting the program in the Guide at the exact time of a first run showing (11pm, in your case), and not on a repeat entry in the Guide. Then, even it The Daily Show is tagged as New for repeat showings, these will be ignored.
Third, another channel may air reruns of the program in your series recording, and the first showing of a rerun episode on the other channel may be tagged as "New". These can be ignored in your series if you set the series option "Channel" to "Selected Channel". Related to this, if there is both an SD and HD channel broadcasting you series program, you will record them both if the series option "Duplicates" is set to "Yes". However, when the Channel option is set to "Selected Channel", the Duplicates Option is always effectively "No", regardless of what shows up on the options screen.
As for you missing two minutes, I have sereral instances in which two programs start recording at the same time. To the best of my recollection, whenever the warning message has appeared, ignoring it has not caused a loss of recording time. You might have an older software version. Newest is v.1.8. Look at Menu--Settings--System Info. Or, I might not have noticed the loss of minutes. I regularly see up to a minute of previous programming at the start of a recording, or a few missing seconds at the beginning or end of a recording. There are a lot of possibilities for that, but the DVR clock being incorrect is not one of them. With RCN, the DVR clocks occasionally drifted off by as much as a minute and a half. -
Pension issue Mid Month Leaving
Dear All,
As per rule sustem should deduct mid month joining/leaving/absences or transfer scenarios, the Pension/PF Basis will be correspondingly prorated. But our system is not doing this. In RT table i have found 3FC Pension Basis for Er c 01/2010 0.00 6,500.00.
Employee leaving date is 14.04.2010. system is picking pension amout as 541. Last year it was coming right.
Please suggest.
AshwaniDear Jayanti,
We required prorata basis pension in case of left employees and system is not doing this. This is the issue. As per our PF experts Pension amount should come on prorata basis for left employees in case they left mid of month.System is doing prorata basis last year but from this year it is deducting 541. I am giving two RT cases of different years.
RT table for year 2010. DOL 26.04.2010
/111 EPF Basis 01/2010 0.00 8,750.00
/139 VPF Basis 01/2010 0.00 8,750.00
/3F1 Ee PF contribution 01/2010 0.00 1,050.00
/3F3 Er PF contribution 01/2010 0.00 509.00
/3F5 Ee Mon PF contribution 01/2010 0.00 1,050.00
/3F6 Ee Ann PF contribution 01/2010 0.00 12,600.00
/3F9 PF adm chrgs * 1,00,00 01/2010 0.00 96.25
/3FA PF basis for Ee contri 01/2010 0.00 8,750.00
/3FB PF Basis for Er Contri 01/2010 0.00 8,750.00
/3FJ VPF basis for Ee contr 01/2010 0.00 8,750.00
/3FL PF Basis for Er Contri 01/2010 0.00 6,500.00
/3F4 Er Pension contributio 01/2010 0.00 541.00
/3FC Pension Basis for Er c 01/2010 0.00 6,500.00
/3FB PF Basis for Er Contri 01/2010 0.00 8,750.00
/3FC Pension Basis for Er c 01/2010 0.00 6,500.00
/3FJ VPF basis for Ee contr 01/2010 0.00 8,750.00
/3FL PF Basis for Er Contri 01/2010 0.00 6,500.00
/3R3 Metro HRA Basis Amount 01/2010 0.00 8,750.00
1BAS Basic Salary 01/2010 0.00 8,750.00
RT table for year 2009. DOL 27.10.2009
/111 EPF Basis 07/2009 0.00 9,016.13
/139 VPF Basis 07/2009 0.00 9,016.13
/3F1 Ee PF contribution 07/2009 0.00 1,082.00
/3F3 Er PF contribution 07/2009 0.00 628.00
/3F5 Ee Mon PF contribution 07/2009 0.00 1,082.00
/3F6 Ee Ann PF contribution 07/2009 0.00 8,822.00
/3F9 PF adm chrgs * 1,00,00 07/2009 0.00 99.18
/3FA PF basis for Ee contri 07/2009 0.00 9,016.00
/3FB PF Basis for Er Contri 07/2009 0.00 9,016.00
/3FJ VPF basis for Ee contr 07/2009 0.00 9,016.00
/3FL PF Basis for Er Contri 07/2009 0.00 5,452.00
/3FB PF Basis for Er Contri 07/2009 0.00 9,016.00
/3FC Pension Basis for Er c 07/2009 0.00 5,452.00
/3FJ VPF basis for Ee contr 07/2009 0.00 9,016.00
/3FL PF Basis for Er Contri 07/2009 0.00 5,452.00
/3R4 Non-metro HRA Basis Am 07/2009 0.00 9,016.13
1BAS Basic Salary 07/2009 0.00 9,016.13
Now please suggest what to do. where is the problem ? If have also checked EXIT_HINCALC0_002 but nothing written in it.
With Regards
Ashwani -
Open PO Analysis - BW report issue
Hello Friends
I constructed a query in BW in order to show Open Purchase Orders. We have custom DSO populated with standard
datasource 2lis_02_itm (Purcahse Order Item). In this DSO we mapped the field ELIKZ to the infoobject 0COMP_DEL
(Delivery completed).
We loaded the data from ECC system for all POs and found the following issue for Stock Transport Purchase orders (DocType = UB).
We have a PO with 4 line items. For line items 10 and 20, Goods issued, Goods received and both the flags "Delivery
complete" and "Final delivery" checked. For line items 30 and 40, only delivery indicator note is issued for zero
quantity and Delivery complete flag is checked (Final delivery flag is not checked) in ECC system. For this PO, the
delivery completion indicator is not properly updated in the DSO for line items 30 and 40. The data looks like the
following:
DOC_NUM DOC_ITEM DOCTYPE COMP_DEL
650000001 10 UB X
650000001 20 UB X
650000001 30 UB
650000001 40 UB
When we run the Open PO analysis report on BW side this PO is appearing in the report but the same is closed in ECC
system.
Any help is appreciated in this regard.
Thanks and Regards
sampathHi Priya and Reddy
Thanks for your response.
Yes the indicator is checked in EKPO table for items 30 and 40 and delta is running regularly for more than 1 year and no issues with other POs. This is happening only for few POs of type Stock Transport (UB).
I already checked the changes in ME23N and the Delivery completed indicator was changed and it reflected in EKPO table. Further, i checked the PSA records for this PO and i am getting the records with the Delivery completed flag but when i update from PSA to DSO the delivery completed indicator is not updating properly.
In PSA, for item 30 i have the following entries. Record number 42 is capturing the value X for ELIKZ but after that i am getting two more records 43 and 44 with process key 10 and without X for ELIKZ. I think this is causing the problem.
Record No. Doc.No. Item Processkey Rocancel Elikz
41 6500000001 30 11 X ---
42 6500000001 30 11 --- X
43 6500000001 30 10 X ---
44 6500000001 30 10 --- ---
(Here --- means blank)
Thanks and Regards
sampath -
HP LaserJet Enterprise 600 M602 driver issue
Hello,
I've got issue with 600-series printers. We use the latest UPD drivrer ver. 61.175.1.18849 and print from XenApp 6.5. The error occurs every time when users try to print jpg files from XenApp session. It only happens with 600 series printers and UPD.
Also I've tried to assign native 600-series driver ver. 6.3.9600.16384 and it works good. But with that driver system says that it's color printer and it brokes our printing reports. These reports are very important for us. So we can't use printer and that driver as well.
Printer installed on Windows Server 2012 R2. All clients are Windows 7 x64. XenApp Servers are Server 2008R2.
Is it possible to get fixed UPD driver or correct native driver for Server 2012 R2?
Regards,
AnatolyI am sorry, but to get your issue more exposure I would suggest posting it in the commercial forums since this is a commercial printer. You can do this at Printers - LaserJet.
Click on New Post.
I hope this helps.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP -
Windows 7 displays error message when exiting +cursor issue
Two issues here. CS5 Phoshop on Wind 7 64 bit.
Physical processor count: 8
Processor speed: 3073 MHz
Built-in memory: 12279 MB
Free memory: 9577 MB
Memory available to Photoshop: 10934 MB
Memory used by Photoshop: 80 %
Image tile size: 128K
First issue is since the latest automatic Adobe update (why fix what isn't broken?) Every time I now exit Photoshop I get the message "Adobe QT Server has stoped working" and occasionally it happens when I exit bridge. Indesign is also behaving badly. I can no longer start a previous document from file manager without ID crashing out.
The other is the cursors in Clone and erase lose their edge (become invisable) for no reason - well not quite. Noise Ninja crashed Photoshop when I tried to use it. I reinstalled it and all is well. The cursor issue seems to be intermittant but came back (for no reason) after I reinstalled NN. I can't seem to change the cursor, no matter what I do. The problem is now seriously affecting how I work. Almost enough to go back to Win XP which ran CS5 Photoshop flawlessly.
Any help will be gratefully accepted.
Dougfunction(){return A.apply(null,[this].concat($A(arguments)))}
doug87510 wrote:
The recent problem is the entire outline of the cursor (including the crosshair in the middle) was missing at any size of cursor. All I had was exactly what I'd get if I used a real spraygun.
Well, that issue is simply a matter of hitting the Caps Lock key. When Caps Lock is on, you'll see the cursor outline, and when it is off you'll see a crosshair. That's a feature, not a bug.
Glad to hear the 11.1 drivers are out. I will download them and try them now myself.
Regarding "Adobe QT" crashing... QT brings to mind QuickTime, though that is Apple, not Adobe. Do you have Apple QuickTime installed?
Regarding memory usage, with 12 GB of installed RAM, you should be able to set Photoshop to use 90% or more in Edit - Preferences - Performance.
-Noel -
Issue in Creation of Periodicals for Contracts in CRM7.0
Hello,
I have a requirement to create Contracts in CRM7.0 system.
And I am doing this using the BAPI *BAPI_BUSPROCESSND_CREATEMULTI*
Good part is Contract Order gets created, but onlywith Header Details.
The issues i am facing --
1. I need to know what kind/type of data must be passed to the interface parameters, the F1 Help/Documentation is vague.
2. I am passing data in the INPUT FIELDS structure with the Object ID, Handle Number, Reference GUID and Fieldname,
here what does 'Logical Key' field indicate? What should be passed here.
What does 'REFERENCE KIND' field indicate, i have been passng 'A' for everything (to be frank i dont know whats its significance is!!).
3. With so much, My Order gets created but with less than half details, i.e. the Objects not getting created are - Partner, Product, terms/appointments, Status, LongTexts......
Any help/inputs would be appreciated.
Hope my problem is stated clearly ...
--Regards
DedeepyaHi Anu,
i found my solution by debugging with existing data or while creating it in CRMD_ORDER.
Ensure that you are passing a correct entry in INPUT_FIELDS structure.
As i haven't worked on rebates i woudlnt be able to help you, I suggest you debug to arrive at a solution.
You can preset your break-points at :-
1. FM - CRM_ORDER_MAINTAIN
2. CRM_ORDER_MAINTAIN_MULTI_OW -- Debug through the complete FM.
3. CRM_ORDER_PREPARE_MULTI_OW -- The data is set in this function module.
Regards
Dedeepya C -
Issue in creation of plant related data at receiving server using BD10
Hi all,
This is regarding Material master creation using B10.I am using MATMAS05 message type for sending data from one system to another.Data is sent and received successfully.When i go in mm03 i can see all the views created successfully accept views related to PLANT.Please guide to resolve the issue.
When i entered into Log-
1)"The field MBEW-BKLAS is defined as a required field; it does not contain an entry".
2)"No material master data exists for material AB_08.04.09(30) in plant 4001".
My segemnt is as follows-
ZMATMAS05 matmas05
E1MARAM Master material general data (MARA)
Z1KLART KLART----
My extention
E1MARA1 Additional Fields for E1MARAM
E1MAKTM Master material short texts (MAKT)
E1MARCM Master material C segment (MARC)
Z1AUSPM E1AUSPMDistribution of Classification:----
My extention
E1MARC1 Additional Fields for E1MARCM
E1MARDM Master material warehouse/batch segment (MARD)
E1MFHMM Master material production resource/tool (MFHM)
E1MPGDM Master material product group
E1MPOPM Master material forecast parameter
E1MPRWM Master material forecast value
E1MVEGM Master material total consumption
E1MVEUM Master material unplanned consumption
E1MKALM Master material production version
E1MARMM Master material units of measure (MARM)
E1MBEWM Master material material valuation (MBEW)
E1MLGNM Master material material data per warehouse number (MLGN)
E1MVKEM Master material sales data (MVKE)
E1MLANM Master material tax classification (MLAN)
E1MTXHM Master material long text header
E1CUCFG CU: Configuration data
E1UPSLINK Reference from Object to Superior UPS
Thanks.
Edited by: sanu debu on Apr 27, 2009 7:10 PMCREATE CONTROLFILE SET DATABASE "NEWDB" NORESETLOGS ARCHIVELOGAlso when you are setting a new database, the option should be RESETLOGS and not NORESETLOGS.
'D:\APP\ADMINISTRATOR\ORADATA\NEWDB\ONLINELOG\O1_MF_2_7FK0XKB8_.LOG
D:\APP\ADMINISTRATOR\ORADATA\NEWDB\DATAFILE\O1_MF_SYSTEM_7FK0SKN0_.DBFWhy underscore(_) at the end of the datafile name. Any specific reason ? -
Issue in Creation of new Value Field in CO-PA
Hi,
I have a query in CO-PA Value Field Linking.
In my Development Client,
1. Created a New Value Field (No Transport Request Generated)
2. Linked to the above to new Conditon type created in SD. (Tranport request was generated) i.e. in Flow of Actual Values->Transfer of Billing Documents->Assign Value Fields
However then i try creating a new Value Field in my Production Client it throws a message 'You have no authorization to change Fields".
Is this an issue with authorization or i need to transport the Value field too from Development to Production client.
Please Advise.
Thanks in Advance,
SafiThanks Phaneendra for the response.
The creation of Value field did not create any tranportation request. Will this too be transported if i transport the Operating Concern.
Please Advise.
Thanks,
Safi -
Dear All
I have some is my current assignment-Customer is buying some material say "A" want "B,C" as exclusive free goods
is it possible to give two free at a time in same order ?
I only know one exlusive free good can be give to one material with combination of customer ( Customer/Material)
Looking for some inputs regarding the issue.
Can you plz suggest me if there is any possiblities for BOM?
Many Thanks
Rakesh NaveenDear Rakesh,
Be informed that free goods is not currently supported in combination with material structures (e.g. product selection,
bills of material, variants with BOM explosion), see note 796926.
Determination of free goods is performed in include FV45PF0N_NATRAB_SELECTION and the check is hardcoded. You will have to modify the program to get that functionality, but be carfull that any modification won't be supported by SAP, see note 170183.
I hope it can help you.
Ruy Castro
Maybe you are looking for
-
Can I use airport express to extend my network AND stream iTunes???
I have an airport extreme connected to the cable modem and sending a signal out to my home network. I also have a powerbook and an airport express connected to the home stereo. My question is, can i use the express to extend my extreme signal (to rea
-
DVB-S Tv Card Problems /dev/video
Hello, I have a Terratec Cinergy DVB-S TV card, the modules (dvb-ttpci and others) are correctly loaded by hotplug. So far so good. Yet nothing works (tvtime & kdetv), it can't get a signal. In the terminal, it says: videoinput: Cannot open capture d
-
Keeps saying "Your Apple ID has been disabled." Tried resetting my password and I'm still getting same message
-
Hi guys! I have a dynamic sql report with apex_item popup from lov function. Everything works fine except pop up itself. When I clich this poup icon and select a vaule it appears in different row (example two rows down) and not in the row I've clicke
-
Problem to Activated my ipad 2??
plz some help here This what apper to me on itunes We're sorry, we are unable to continue with your activation at this time.