Missing pci bus 2 and PCI/VEN_10EC&DEV_5209& SUBSYS_3577 103C&REV

missing pci bus 2 and PCI/VEN_10EC&DEV_5209& SUBSYS_3577 103C&REV. Can someone please help me and tell me how to get these drivers downloaded to my pc.Id really appreciate it and thanks in advance...

Hi, It is the card reader. Please try the first one for Windows: http://www.realtek.com.tw/Downloads/downloadsView.aspx?Langid=1&PNid=15&PFid=25&Level=4&Conn=3&DownTypeID=3&GetDown=false Regards.

Similar Messages

Sharing an external sample clock between PCI-6722 and PCI-6602

I need PCI-6602 work with PCI-6722。6602 shares 6722’s ao/SampleClock as external clock and triggered by 6722’s ao/StartTrigger。The master device is 6722, which refered as Dev1, and the slave device is 6602, which refered as Dev2. A RTSI line is used to connect the two devices correctly.
I use C API to finish my program and my code is as follows:
//config 6722 analog out task
1、DAQmxCreateTask("NI6672", &hAOTask);
2、DAQmxCreateAOVoltageChan(hAOTask, "Dev1/ao0", "", -10.0, 10.0, DAQmx_Val_Volts, "" );
3、DAQmxCfgSampClkTiming(hAOTask, "", 1000.0, DAQmx_Val_Rising, DAQmx_Val_ContSamps, 1000);
4、DAQmxWriteAnalogF64(hAOTask, 1000, 0, 10.0, DAQmx_Val_GroupByChannel, data, NULL, NULL);
//config 6602 counter task
5、DAQmxCreateTask("NI6602", &hCounterTask);
6、DAQmxCreateCICountEdgesChan(hCounterTask, "Dev2/ctr0", "", DAQmx_Val_Rising, 0, DAQmx_Val_CountUp);
//use /Dev1/ao/SampleClock for external clock
7、DAQmxCfgSampClkTiming(hCounterTask, "/Dev1/ao/SampleClock", 1000.0, DAQmx_Val_Rising, DAQmx_Val_ContSamps, 1000);
//use /Dev1/ao/StartTrigger
8、DAQmxSetTrigAttribute (hCounterTask, DAQmx_ArmStartTrig_Type, DAQmx_Val_DigEdge);
9、DAQmxSetTrigAttribute (hCounterTask, DAQmx_DigEdge_ArmStartTrig_Src, "/Dev1/ao/StartTrigger");
10、DAQmxSetTrigAttribute (hCounterTask, DAQmx_DigEdge_ArmStartTrig_Edge, DAQmx_Val_Rising);
//start counter task first
11、DAQmxStartTask(hCounterTask);
//start 6722 task
12、DAQmxStartTask(hAOTask);
I run it on the MAX virtual Device, and the Step 11always returned -89120。
I try to slove this problem, so I change the Step 7, use /Dev2/PFI9 to instead of /Dev1/ao/SampleClock.
7、DAQmxCfgSampClkTiming(hCounterTask, "/Dev2/PFI9", 1000.0, DAQmx_Val_Rising, DAQmx_Val_ContSamps, 1000);
The code runs well, but I don’t know which terminal is connected by /Dev2/PFI9. Does it connect to /Dev1/ao/SampleClock？
I use another API DAQmxConnectTerms to ensure that, I add a Step before Step 11.
DAQmxConnectTerms( "/Dev1/ao/SampleClock", "/Dev2/PFI9", DAQmx_Val_DoNotInvertPolarity );
The program also run well. But I am still not sure that 6602 is sharing /Dev1/ao/SampleClock。If not, which terminal of Dev1 is connected by /Dev2/PFI9?
Is my code right? If not, hwo to fix my code or supply some example for me? Thanks.

Hello Shokey,
From looking over your post, it looks like you want to program in C, using simulated instruments, a master/slave design with a PCI-6602 and PCI-6722. The PCI-6722 is the master device and the PCI-6602 is the slave device. In order to implement this with the real cards, you would need a RTSI cable between the 2 cards in order to pass the triggers and the sample clock. Unfortunately with simulated devices you can't implement this so parts of your code won't be able to work exactly like if you had the instrument.
If you did have the instrument, you can implement this by performing the following steps:
Master Device:
1.) Export the ao/SampleClock and ao/StartTrigger to a RTSI Line. (See DAQmx C Reference help for DAQmxExportSignal to export these)
Slave Device:
1.) Set the Sample clock and the trigger to the RTSI.
There is another forum that I think will help you out to implement this correctly. In this forum, the customer was trying to export a trigger through a RTSI and the problem he was experiencing was a broken RTSI cable. His code, he states, works. I hope this helps you with this and if you have any more questions, feel free to post.
Jim St
National Instruments
RF Product Support Engineer

Inquiring about the issue of using PCI-5922 and PCI-5412 simultaneously under Linux OS! Thank you!

hi all,I am lily and I an AE from NI shanghai .Now I confronted a pullze from customer,and I really feel at a loss! Hope some one of you would come and land me a hand,thank you in advance!
The problem is as follows:
Customer use PCI-5922 and PCI -5412 under Linux OS, if they use either of the two cards seperately,there would be OK. but if the use both of the two cards simultaneously, the error will occured as attachment shows. "Error code:-50258 occured at niscope_DAQmx Create Channel (AI-Voltage-Base).vi:2 Possible reason(s):The specified software component failed to initialize."
Can I know is there any solution vs this probelm?Thank you in advance!!
Attachments:
Screenshot-NI-DAQmx Test Panels.png ‏17 KB
NI-NEW_error.txt ‏8 KB
shortsyms.txt ‏973 KB

This is the wrong board for this question, you should re-post here
Regards
Ray Farmer

How to reduce reading and recording data time/ Visual C++, PCI 6024E and PCI-MIO-16E?

Right now I am working on a data communication programme. The time of reading digital signal and recording data is more than I expected, which is about 100 microsecond. I need to reduce the time. The software I am using is Visual C++ 6.0. I use two DAQ boards, which are PCI-6024E and PCI-MIO-16E. I have set the priority of Visual C++ to be realtime by task manager. The operating systme is Windows XP.
I am wondering how to set the interrupt of reading or writing data to be the highest and stop any other kind of interrupt.
Thanks in advance!

The primary limitation you will encounter when trying to do high speed
digital I/O using your E-Series hardware is that the digital lines are
all software timed. This means that for each and every digital
read it is necessary for your software to issue a command to your
hardware, read a single point, then receive the response from the
board. This prevents you from performing digital operations at
very high speed. In general, I would say that 100 microseconds is
a very good response using software-timed digital I/O on a Windows
computer.
It is difficult to make a good recommendation without more detail about
what you are trying to do. You may need to consider switching to
a Real-Time operating system, or upgrading your DAQ hardware to a board
that will allow you to time your digital acquisitions on the board
itself. These devices, such as the m-Series DAQ or the PCI-653x
series, would allow you to use hardware triggers for your digital
acquisitions, change detection, and buffered data acquisitions to
reduce the software overhead involved in a rapid acquisition.

PCI bus and memory ranges in Device Manager.

Hello,
I looked in device manager on my netbook that has no dedicated graphics card (so no dedicated VRAM) and uses shared system RAM as
it’s video buffer, the following memory ranges have been assigned to the on board card -
If I then change the view in device manager to ‘Resources by type’, Windows shows the following memory ranges to be on the PCI bus
Basically all the memory ranges that have been assigned to the card are shown to be also on the PCI bus. I would understand this with
a dedicated graphics card where data needs to be forwarded onto the PCI bus but I know my netbook is using system memory as the frame buffer which then I assume the card reads from there.
Do you know why these addresses are shown to be on the PCI bus, is it just because the card is a PCI device so it’s easier for Windows
just to display them as if they were on that bus, and anything written to these address will still go into system memory?
I know it’s a bit of a random question but I’ve been trying to find an answer online and can’t seem to find anything.
Any help would be appreciated,
Thanks.

Hi,
For your question: Do you know why these addresses are shown to be on the PCI bus, is it just because the card is a PCI device so it’s easier
for Windows just to display them as if they were on that bus, and anything written to these address will still go into system memory?
Yes.
You can check the hardware memory usage via Resource Monitor.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

What is the difference between PCI-x and PCI Express?

I hear the new dual core Power Macs have PCI Express slots. How are these different than the PCI-X slots in my old Power Mac?
jmf

PCI Express is faster than PCI-X and not a bus architecture. Each slot has its own dedicated bandwidth to and from the system controller.
PCI-X has a maximum clock speed of 133 MHz and a maximum throughput of just over 1 GBps.
PCI Express cards and slots are defined by their bandwidth, or number of data lanes — typically one lane, four lanes, eight lanes, or 16 lanes. At 250 MBps per lane, a four-lane slot can transfer data at up to 1 GBps and an eight-lane slot, up to 2 GBps. The new PowerMac G5s have one 16 lane slot, two four-lane slots, and one eight-lane slot.

Work with PCI-6052E and PCI-6601 simultaneously

Hi, I'm working with PCI-6052 for bufered data output and PCI-6601 for read two encoders at same time, when I work with single board I don't have problems but when I work both simultaneously I have a problem only I can out data or only I can read the encoders but not both at the same time. How I make this?

Hi,
You probably have one task in LabView running in series after the other. Both of these tasks require a loop. Your buffered data output needs to be written in continuous fashion in a loop (I believe) and your encoder measurements are being read constantly as well (should be in a loop). Try experimenting with these two suggestions.
I would copy both programs into 1 VI and keep them running completely separate. LabView will be able to assign each a different thread so they should be able to run completely in parallel. Therefore you would have 2 parallel loops that are not connected at all.
You can also create two completely different VIs and run them in parallel. There is no reason why the two different programs would interfere.
Hope that he
lps. Have a good day.
Ron

Eeprom address and caldacs model/address for pci-6014 and pci-6733

I have one pci-6014 and one pci-6733.
I need to transfer the calibration constants from eeprom to caldacs.
I search the adrress of the constants in the eeprom and the model and address of che caldacs.
Tanks

Hello,
It seems to be a common mode voltage or ground loop problem.
When you are sourcing an output signal from your DAQ board, the signal is already grounded, it means that it has already a reference. If you measure this output with a measurement device, which has also a ground, the both ground potential are not necessary equal. This difference is the common mode voltage and influences your measurement (offset).
Please check the following links to have more detail about grounded signal.
http://zone.ni.com/devzone/conceptd.nsf/webmain/8D907374C5E867F186256C640059F30C?opendocument
http://digital.ni.com/worldwide/france.nsf/webtechsupp/0E6A8D5999CEE1AF8025683C0056A4B1?OpenDocument&node=163080_f
Best regards,
Alexandre D
National Instruments

I2C Bus and PCI-DIO-96

i want to use PCI-DIO-96 to communicate with one i2c instrument by i2c bus. Anybody has sameple vi for that? Or give me some concept that how to programm with LV or CVI? Thanks a lot !

Duplicate Link:
http://exchange.ni.com/servlet/ProcessRequest?RHIVEID=101&RPAGEID=137&HOID=506500000005000000345A0100&HTHREAD=000088628&UCATEGORY_0=_31_%24_12_&UCATEGORY_S=0

Synchronize PCI- 5421 and PCI-6602

I am using a PCI 6602 to generate four pulse trains. I am also generating a signal with a PCI 5421 AWG. All signals are started at the same time by using a common start trigger. The problem I am having is that after they run for a while the 6602 and 5421 signal start drifting. I know in the past I had sync clocks in a PXI chassis but I am unsure how to syncronize the clocks using PCI card. I do have an RTSI cable linking the cards together so could someone please give me an example of how to sycronize these cards in Labview (8.2)

Hello Kiebach,
You seem to be connecting the signal correctly in your NI-DAQmx program. However, I do not see any NI-FGEN code where you import the signal to be used as an external clock. Have you added this code? I think you would benefit from examining the example program entitled "niFgen_DAQmx_Synchronization_Example.vi". This program shows how to synchronize an NI-DAQmx device and an SMC Arb device. You can find the example by opening the NI Example Finder utility; you can open this utility from LabVIEW by going to the Help menu and selecting Find Examples... Once you have opened the NI Example Finder, you can navigate to this example by selecting the Browse tab and going to Hardware Input and Output>>Modular Instruments>>NI-FGEN (Signal Generators)>>Synchronization. You will notice that this example uses the Export Signals VI rather than the Connect Terminals VI. To help understand the difference between these two, you may want to examine this document.
Matt Anderson
Hardware Services Marketing Manager
National Instruments

To access Kistler Dynamometer Amplifier (4 component) do I need to use PCI 4452 and PCI 1200 ( I have both of them) with DAQ/LAbview.

If yes How to relate them together both in VI and by Hardware.
Thanks,
Niraj

"Thanks for your attention,
I have Dynamometer with four analog outputs to respective amplifier's,all of which I have to connect to NI's BNC 2140, which will be connected to PCI 4452, now I even have PCi 1200 which is also a DAQ card I suppose. I want to know whether I need to connect both of these together in anyway, and ultimatly will they appear on single VI together or seperatly. Like I have developed single VI for both, but Is it possible to Develop VI with access to both.
Also is it necesary to use both, I want to know whether my application will be handled by PCI 4452 alone,
I suppose I am clear this time about my application and things available with me.
please let me know if not,
Thanking you,
Niraj"

K9N Neo V3 : PCI-E and PCI-E x1/PCI VGA cards at the same time ?

Hello,
I'm thinking about getting one more VGA card to resolve my dual screen issue :
Quote
I use two monitors. PC monitor as first screen, TV is extended for watching videos.
PC : Philips 220aw (22", 1680x1050 @ 60Hz) DVI-DVI
TV : LG 42lh3000 (42", 1920x1080 @ 24Hz) DVI-HDMI
I've been trying to get smooth playback on the TV for days, but random stutter happens.
When a video (mostly HD contents) is played on the TV while using the PC monitor, things like minimize/maximize windows, page scrolls stutter and so does the video. Idle while watching videos also stutters randomly.
I tried almost every combinations of renderers/codecs/players, tried by desactivating aero and all the fancy graphics, but it didn't solve the problem.
The only way i get smooth playback on the TV, is by desactivating the PC monitor. (Using nVidia panel or "Win" key+P), so only the TV is active.
I tried with a Blu-Ray using DXVA and it was smooth.
I haven't got a chance to test with a better graphic card yet. This issue doesnt happen on XP though.
Here are the specs :
K9N Neo V3
Athlon 64 x2 @ 3Ghz
4Go DDR2-800
8800 GT 512Mo (driver 197.45)
Win7 Ultimate 32 Bits.
Corsair 450W 80+
My question is : Can i add a PCI-E x1 or a PCI VGA card on this motherboard, so each screen will have its own VGA card ?
If so, both nVidia or ATI would work ?
Thank you.

It would be one of these, if it is allowed by the K9N Neo V3.
http://www.club3d.nl/products/products_ending_page_7_with_id.cfm?product_id=154
http://www.club3d.nl/products/products_ending_page_7_with_id.cfm?product_id=223
I will try to test with an ATI card if i can find one.

PCI Express and Soundblast

I just got a new machine that has PCI Express card slots in it. I am new to this technology so I have a total noob question. Can you use soundblaster cards in a PCI Express slot? And on a larger scheme, can you use PCI cards in PCI Express slots?
Thanks,
-murk

As everybody said... No. PCI-express and PCI are not really compatible.
And I'd like to reply on the posts regarding PCI-express soundcards. If any card like that would be produced, I guess we'd need mainboards with more PCI-E slots than we have now. Now it's all PCI-E on GPU's and 2 PCI-E slots for crossfire/SLI setu
ps.
Gi'ven I want to have a decent gaming machine in the foreseeable future, I'd need atleast 3 if not 4 PCI-E slots. Something like a Physics processing unit comes to mind, 2 GPU's and a soundcard... which would also conclude in a lot of users should be upgrading their systems to a higher substandard then now. Upgrading is fun and all, but if they people can't afford to upgrade that often, most companies would stay pretty low.
That's just my 2 cents. But seeing the developments running wild regarding computers I wouldn't be too surprised if we'd see it happen soon.

Missing Drivers for USB Controllers (2), SM Bus Controller, and PCI Device

Just got this laptop from my grandparents, and they whiped the OS off if it and did a reinstall with windows 7 64 bit. When it reinstalled it was missing many of the drives, most of which I've been able to find, but I still have four left that I can't find anywhere. Device: Hardware ID PC Device: PCI\VEN_10EC&DEV_5209&SUBSYS_1805103C&REV_01
PCI\VEN_10EC&DEV_5209&SUBSYS_1805103C
PCI\VEN_10EC&DEV_5209&CC_FF0000
PCI\VEN_10EC&DEV_5209&CC_FF00 SM Bus Controller: PCI\VEN_1022&DEV_780B&SUBSYS_358B103C&REV_13
PCI\VEN_1022&DEV_780B&SUBSYS_358B103C
PCI\VEN_1022&DEV_780B&CC_0C0500
PCI\VEN_1022&DEV_780B&CC_0C05 Universal Serial Bus (USB) Controller: PCI\VEN_1022&DEV_7812&SUBSYS_358B103C&REV_03
PCI\VEN_1022&DEV_7812&SUBSYS_358B103C
PCI\VEN_1022&DEV_7812&CC_0C0330
PCI\VEN_1022&DEV_7812&CC_0C03 Universal Serial Bus (USB) Controller: PCI\VEN_1022&DEV_7812&SUBSYS_358B103C&REV_03
PCI\VEN_1022&DEV_7812&SUBSYS_358B103C
PCI\VEN_1022&DEV_7812&CC_0C0330
PCI\VEN_1022&DEV_7812&CC_0C03 I have tried uninstalling the devices and rebooting the laptop, and updating the drivers using this site (suggested for someone else having the same issue) http://support.amd.com/en-us/download. When I looked on hp's site there is no driver that I saw for any of these.

Are you using drivers from your Support page? The AMD graphics driver usually has sm bus and usb drivers. The PCI device is Realtek Card Reader, also in the list. You can also order Recovery Media which reinstalls Windows and all drivers & software. http://support.hp.com/us-en/drivers/selfservice/HP-Pavilion-dv6-6c00-Entertainment-Notebook-PC-series/5191856/model/5210864#Z7_3054ICK0KGTE30AQO5O3KA30R1 Too bad your grandparents didn't use HP Recovery Manager installed on the laptop to reinstall Windows. That would have prevented this.

Network controller and pci device driver missing for Toshiba Sattelite c55t b5109

After resetting windows 8.1, I only my ethernet works and I cant turn my wifi. I looked in the device manger, and under "unknown devices" are listed Network Controller and PCI Device with yellow alerts near them. I know that these are related to the wireless card, but everytime I try to update them they say that there is no driver for them.
These are their hardware id's:
Network Controller:
PCI\VEN_168C&DEV_0036&SUBSYS_083211AD&REV_01
PCI\VEN_168C&DEV_0036&SUBSYS_083211AD
PCI\VEN_168C&DEV_0036&CC_028000
PCI\VEN_168C&DEV_0036&CC_0280
PCI Device:
PCI\VEN_10EC&DEV_5229&SUBSYS_F91B1179&REV_01
PCI\VEN_10EC&DEV_5229&SUBSYS_F91B1179
PCI\VEN_10EC&DEV_5229&CC_FF0000
PCI\VEN_10EC&DEV_5229&CC_FF00
PLEASE HELP!!!!

search your laptop for the Toshiba application installer, open it and use it to install your Wireles lan driver.
The application installer is easier than guessing which one you need from your support page.
OR
Your support page is here - http://support.toshiba.com/support/modelHome?freeText=1200008391
You can select the drivers tab then down the page on the left hand side select Windows 8.1 64 bit to narrow down the drivers for your operating system. Then also select Wifi and the available drivers will be displayed.
If you are getting a corrupted system after a reset your hard drive may be failing or your recovery partition may have been corrupted . Create your recovery media if you have not done so already.
S70-ABT2N22 Windows 7 Pro & 8.1Pro, C55-A5180 Windows 8.1****Click on White “Kudos” STAR to say thanks!****

Missing pci bus 2 and PCI/VEN_10EC&DEV_5209& SUBSYS_3577 103C&REV

Similar Messages

Maybe you are looking for