MOH doest not works

Hello,
   I have a simple setup with one core 3560 switch with 2 vlans Data 192.168.100.x and Voice 192.168.200.x and CME 4.1 installed on a  router 2801 with an IP address 172.16.0.1 connected to it. My phones are registering well and I am able to call. When I am trying to implement MOH it doesnt works here are the commands which I Have used
telephony-service
moh music-on-hold.au
multicast moh 239.23.4.10 port 2000
your help will be appreciated

Hi Syed
Can you find the below?. I hope to check if the audio file on the flash.
ip multicast-routing
ccm-manager music-on-hold
CME(config)# telephony-service
CME(config-telephony)#no moh "music-on-hold.au"
CME(config-telephony)# moh flash:music-on-hold.au
CME(config-telephony)# no create cnf-files
CME(config-telephony)#create cnf-files
also find the following URL:-
http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmemoh.html#wp1010372
http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/feature/guide/MoH.pdf
Thank you
please rate all useful infomation

Similar Messages

  • Headphone's buttons doest not works

    I bought my iphone at this sunday.
    Made the iOS update , to 7.03  etc...
    and then tried to listen the music VIA headphones
    the volume buttons does not work. I tried with several headphones (5s and 5 headphones)
    in all cases the sound was great... but the control pad was not working (volume +/-) and answer the call.
    What to do?
    Thanks
    anar

    I don't think it's a universal issue as I don't see many complaints here in the forum, and it works for me.
    If you're sure the headphones are ok, check to be sure there isn't anything stuck in the headphone jack that may be interfering with the contacts.

  • UCCX 7: Network MoH ringback not working with Multicast MoH.

    Hi All,
    I have a CUCM and UCCX installed in a Data Centre serving a site across a WAN,  on the site there are agents using CAD and a backup SRST router, unicast MoH was streamed across the WAN from CUCM in G729 format and network MoH (ringback.wav file) from the CTI ports to give ringback to calls been transferred to agents in the call centre.
    To conserve BW and have better quality MoH, Multicast MoH was configured to stream the User MoH from the routers flash instead of a G729 unicast stream across the WAN. To get Multicast MoH to work I had to change the MoH streaming codec from G729 to G711u on the CUCM. This enables the CUCM to get signal to the phones to join the Multicast stream on the SRST router when a call is placed on hold but as this is a cluster parameter it stopped the ringback MoH on the CTI ports resulting in no ringback when callers are been transferred to the agents in the contact centre. Is there any way I can get the script to play the ringback.wav file when transferring calls to agents or get the call manager to stream the ringback across the WAN while Multicast MoH is implemented?
    Any help or ideas would be really appreciated
    Thanks
    Neil

    Hi,
    When the call is ringing on the agents phone CUCM should be sending the appropriate commands to the endpoints to join whatever multicast stream you have configured for network hold. The issue is that no multicast stream is available on that IP address/port number combination. (I assume that you have set the SRST MoH parameters to match what is sent for user hold).
    SRST versions up to 7.x only support one MoH stream. However SRST 8.0 has extended this to five streams so I think this could be a solution to your problem. Check out the document below.
    http://www.cisco.com/en/US/partner/docs/voice_ip_comm/cusrst/feature/guide/MOH_srst.html
    You will need IOS Release 15.0(1)XA to support this feature.
    An alternative would be to stream the MoH from another multicast source. This could be a PC running VLC if things were tight.
    Please let us know how you get on.

  • LGWR ASYNC doest not working for redolog files, while archiving is working

    Hi All,
    I am using Oracle Database 10g Enterprise Edition Release 10.2.0.4.0.
    I have created a database named black. I then creaetd a standby database. now I want to syncronize the redo logs file as well.
    SO I added log_archive_dest_2='SERVICE=standby LGWR ASYNC',
    I have also added following standby log files on standby database.
    ALTER DATABASE ADD STANDBY LOGFILE '/oracle/oradata/black/srl1.f' SIZE 52428800;
    ALTER DATABASE ADD STANDBY LOGFILE '/oracle/oradata/black/srl2.f' SIZE 52428800;
    ALTER DATABASE ADD STANDBY LOGFILE '/oracle/oradata/black/srl3.f' SIZE 52428800;
    ALTER DATABASE ADD STANDBY LOGFILE '/oracle/oradata/black/srl4.f' SIZE 52428800;
    Now I want to confirm that the redo log files are syncronizing same time on both Primary and Standby. I have checked thru alter system switch logfile; when i executed the redo log sync at both sides.
    Archive logs are also applying successfully.
    The Primary database is in MAXIMUM PERFORMANCE Mode;
    Regards,
    Hassan

    Hi Khurram,
    I have successfully executed the commands on Primary Database as below: (Standby database was in mount state at that time)
    SQL> startup mount;
    ORACLE instance started.
    Total System Global Area 1258291200 bytes
    Fixed Size 2083728 bytes
    Variable Size 318768240 bytes
    Database Buffers 922746880 bytes
    Redo Buffers 14692352 bytes
    Database mounted.
    SQL> alter system set log_archive_dest_2='SERVICE=standby LGWR SYNC AFFIRM' scope=both;
    System altered.
    SQL> alter database set standby database to MAXIMIZE AVAILABILITY;
    Database altered.
    SQL> alter database open;
    Database altered.
    SQL> shutdown immediate;
    Database closed.
    Database dismounted.
    ORACLE instance shut down.
    SQL> startup
    ORACLE instance started.
    After that I activated managed recovery process on standby database and all archive files were applied successfully;
    Then I executed a script to insert 2000 records in Primary Database Scott Schema, and during the execution of this script I executed shutdown abort from anothe session on primary database.
    at that time no new archive file generated only redo files was there.
    I then executed below commands on standby database to apply current redo log file but that IS WAHT I WANT TO ACHIEVE IS UN-SUCCESSFULL.
    SQL> alter database recover managed standby database cancel;
    Database altered.
    SQL> recover standby database;
    ORA-00279: change 1065936 generated at 10/22/2009 17:02:43 needed for thread 1
    ORA-00289: suggestion : /oradata/black/arch/1700844250_0000000043.arc
    ORA-00280: change 1065936 for thread 1 is in sequence #43
    Specify log: {<RET>=suggested | filename | AUTO | CANCEL}
    /oracle/oradata/black/stdb_redo01.log
    ORA-00310: archived log contains sequence 42; sequence 43 required
    ORA-00334: archived log: '/oracle/oradata/black/stdb_redo01.log'
    SQL> recover standby database;
    ORA-00279: change 1065936 generated at 10/22/2009 17:02:43 needed for thread 1
    ORA-00289: suggestion : /oradata/black/arch/1700844250_0000000043.arc
    ORA-00280: change 1065936 for thread 1 is in sequence #43
    Specify log: {<RET>=suggested | filename | AUTO | CANCEL}
    /oracle/oradata/black/stdb_redo02.log
    ORA-00283: recovery session canceled due to errors
    ORA-00354: corrupt redo log block header
    ORA-00353: log corruption near block 49141 change 1095254 time 10/22/2009
    17:03:55
    ORA-00334: archived log: '/oracle/oradata/black/stdb_redo02.log'
    ORA-01112: media recovery not started
    The standby redo log files are already generated on standby database. The database is in MAXIMUM AVAILABILITY MODE.
    I have also go through your blog but did not find solution for my issue.
    My scenario is that: SHUTDOWN ABORT (Primary Database) means that server goes down and we have to make our Standby Database as Primary Database, so we need to apply redo log file that niether switched nor applied yet.
    Kindly advice.
    Regards,
    Hassan
    Edited by: Hassan Raza Khan Lodhi on Oct 22, 2009 4:33 PM

  • MOH not working in Directed call park

    Hello All,
    After upgrading the voice gateway from 15.1(2)T2 to15.1(3)T4 im facing this issue.
    MOH is not working in Directed call park. We have 10 Directed call park numbers 100-109, users are parking the calls by pressing trasfer key (transfer key-->dial 100-->transfer key). The Music is stopped playing after the user presses the transfer key for the 2nd time. MOH is working fine in hold and call  park. I can see the MOH session in Show ccm-manager music-on-hold and the same MOH session is continuing after pressing the transfer for the 2nd time, only the music is stopping. There are some sites in the same cluster which MOH working in all conditons but the router is rnning with
    Using: 2900 series voice gateway with H.323, Centralized cluster.
    Assistace will be musch appricidated
    Thanks,
    Murali

    This issue has been identified as new BUG. Cisco is working on this.
    -M

  • MOH not working in cucm only beep sound

    HI,
    I have an IP Telephony set up running on CUCM 9.1.Publisher and subscriber in a single site deployment model.
    Customized MOH were configured and running fine before.Now users are complaining that MOH is not working(both internal and external calls) and only beep sound is hearing  when putting on hold .
    I have checked the MOH server is registered and I have restart  the Cisco IP Voice Media Streaming App service for both pub and sub
    But when i am selecting the Sample Audio source its working fine and I can hear the cisco sound on MOH.
    I have added another audio source for testing and assigned to the phones but result is same.
    Multi cast allowed on the Audio source and its enabled in the MOH server.
    Attached the screen shot for MOH audio source and MOH server.
    Please advice how to fix this issue.

    Beep sound indicates configuration issues, few things to check:
    Make sure the DP assigned to the MOH server is set to use G711 between other regions, unless you enabled other codecs in service parameters
    Make sure the MOH file is uploaded to all servers
    Make sure the MOH server is assigned to MRG/MRGL of the devices needing to connect to it (phones, GWs, etc).
    Can you try using unicast vs. multicast to see if that fixes it?
    Chris

  • Music on hold is not working in CIPC

    Dear All
    can somebody tell me why music on hold is not working in CIPC cisco unifed ip communicator which i have installed in my network for users
    i have configured a router CME to work voip for my network but MoH is not working music on hold is not working
    with regards

    dear i didnt got your point
    but i have configured the multicast on the router and i have nothing did in switch only assigned voice vlan to interfaces and also data vlans to the interfaces so i need a step by step setup of moh can u provide that for me
    with regards

  • 3rd party sip device music on hold not working.

    When creating that COP file, I added the music on hold feature, meaning Music on hold is supported. After the customer installed the COP file into CUCM, created the new device, and configured MOH to play Cisco's sample audio, the MOH does not work. All other features work including Enhanced Message Waiting Indicator, Call Waiting, and Shared Line Appearance.
    When they create a new device in CUCM they follow these steps:
    1. Device > Phones
    2. Add New
    3. Select MH iOS (this is the 3rd party device that has been installed on CUCM via the COP file)
    4. Select Next
    5. Fill out the fields
    6. Select Save and Apply Config
    Please provide the solution or input why it is not working.
    Thanks & Regards,
    Guru

    System Version: 9.0.1.11012-1
    We only hear the Initial and Periodic announcements during the time between the periodic we just get dead air

  • Win Media Encoder on VMWare - Video Devices does not work!!! MBP 15"

    Hi,
    Im trying to setup Windows Media Encoder (9 series) through Windows XP (SP3 Virtualized on VMWare 2.0.5) to make a live webcast event on internet, but my Macbook Pro can't recognize my camcorder (Sony HVRA1)
    I want to setup an live webcast event but when I use an Intel Windows native computer (as I have been doing) all works gook.
    I've get a new Macbook Pro 2.53GHz 15" (aluminium) and I just cant make it work on Windows Media Encoder. The camcorder just doest exist inside Windows.
    First thing I've done was try to find a Win Media Encoder for Mac, but I havent found any. Only converters but they not work with live events.
    I could try others encoders but Im already on a server which just run Windows.
    Any tips how to make it work?
    Thanks in advance.

    Hi lgmmachado,
    Presumably you connect the camcorder to the MBP using Firewire?
    As far as I am aware one cannot access directly from a Virtual Machine a Firewire Port as it is not virtualised and no virtualisation software that I know of works directly with Firewire. I may be wrong here as I've never had the need to do so.
    You would have to install BootCamp, then install Windows and then start up your Mac directly from the BootCamp/Windows partition to directly access the Firewire port from within Windows.
    Kryten

  • FingerPrint Sensor/Software not working right with Windows XP Pro SP3

    Hi All,
    I have a 3 month old Satellite Pro S300-S2504 (2.4 GHz CPU, 3 GB RAM, Bluetooth, firewire - was a custom build with most of the options I could get). The O/S installed was/is Vista Business. It came with a dowgrade XP Pro SP3 disc as well.
    I bought a second hard drive - swapped it with the original and installed Windows XP Pro on it - having grown tired of Vista. I don't intend to keep both O/S's - but I didn't want to mess with what I had until I got XP working - and that's the reason I got the second hard drive for XP. Anyway, XP Pro is installed and working except the fingerprint sensor. As soon as I booted for the first time - with nothing but the factory everything installed, it prompted me to register fingers for the sensor. I tried but I got a database not found error followed by a sensor not working error. I got the latest updates for the fingerprint sensor, removed what I had - rebooted and installed the newer program - I got the same error. I then uninstalled the program again, went through the registry and removed all entries whose key had TrueSuite in it, rebooted and installed the latest version again - rebooted - and got the same errors. Looking in Device Manager, the sensor is working fine but once I try to register a finger and it fails, I then look in Device Manager and the sensor has a yellow error indicator. I used System Restore to go back to the original configuration and then tried the Fingerprint drivers/patches for Vista and for Windows 7. All of them installed but I got the same database not found error followed by the fingerprint sensor not working error.
     I did end the program, then using Task Manager, I ran the Fingerprint utility as administrator - still got the same errors. I've completely reinstalled from the Windows XP restore CD four times trying to solve this and I can't get the fingerprint reader to register fingerprints - I always get that error.
    I have a lot of graphic editing (movies) software as well as file conversion programs and a very stable version of Roxio Easy Media Creator that all works fine in Windows XP - but it all has problems running in Vista and I'm tired of the bugs that Vista seems have - and I want to use Windows XP Pro. I will try any suggestions.  The fingerprint sensor and software works reliably in Vista. I even updated it and that went fine. I suspect there's a problem with the XP version of the software for my computer. I did notice that Toshiba doesn't sell the this model series with XP downgrade as an option anymore. I wonder if this is one of the reasons.
    Anyway - I would very much appreciate help with this. Any ideas at all are welcome.
    Thanks,
    Dennis

    Satellite Pro M10-S405 
    ..a clean Win XP Pro install and it still doesnt work.There is a Win Xp key on the bottom of the laptop, but I cant seem to use it.
    The Product Key that comes with the computer is useless to activate a retail installation. You would need to purchase a new one or convice Microsoft that an old one is no longer in use.
    In the device manager it shows
    Ethernet Controller
    Multimedia Audio Controller
    Network Controller
    Unknown Device needing Drivers. I have searched and downloaded drivers and installed them but it still doest work.
    Get the drivers from here.
    Install the chipset utility first, followed by the display driver. Be sure to install the common modules prior to any Toshiba utilities, including power management.
    -Jerry

  • Display as Key and Name Not working properly after upgrade to Bi7.0

    Hi Bw Guru's
    Recently we have upgrade our BW 3.5 system to BI 7.0 (Only system upgrade not applications ).
    after the upgrade we are facing lot of issues with Bex Analyzer. The following are some of the issues
    1) In BW3.5 after the execution of Workbook or query ,we can convert to local currency .
       Right click on workbook -> Currency translation-> Database currency .
        but after upgrade to BI7.0 this is not working ..
    2) Characterstic Right click on workbook Dispaly as Key and Name is also not working ..
    I know that Currency translation in BI7.0 works in different way compare to BW3.5 .we can use alternate option like By Target Currency from Database currency to convert to local currency and it is working fine in Bex,but businesss users want more friendly way ...because to select the above option they have to enter local currency and rate type ...
    Do you we have any notes available for the above solutions ..?Do we need to upgrade Bex version also..?Is there any document which describe how the above things works after system upgraded to BI7.0?
    Please suggest me..
    Thanks in advance
    Shu Moh.

    Dear Harita
    The first issue Currency translation in query or workbook is solved with SAP note 1119549.For second issue we have not found solution until now ,Once we find the solution we will update you..
    Shu Moh

  • USB-Hub not working on LEFT USB port?

    Hello,
    I have installed Windows 7 Ultimate 64 Bit on my MacBook Pro 13" Retina (Early 2013) and it's running fine. Boot Camp version: 5.0.5033.
    But I have one problem: I bought an external monitor (Dell U2414H) which has an built-in 4-Port USB 3.0 hub. So I connect the Dell monitor using a DisplayPort 1.2a cable and an USB 3.0 cable. But Windows only recognizes the monitor's built-in USB hub when I plug the USB cable into the right USB port (when I sit in front of the MacBook). Then it works without problems. But when I plug the USB cable into the left USB port of the MacBook Windows only says "USB device not recognized". But other devices like USB sticks and USB drives also work without problems on left and right USB port of the MacBook. Also when I boot in OS 10.9 Mavericks the monitor's USB hub is working on both USB ports of the MacBook. So I think it isn't a hardware failure. I also re-installed Windows, but I have still the same problem.
    Do you have any idea, why only the monitor's built-in USB hub is not working in Windows on the left port of the MBP or even how I could fix it?
    Is Boot Camp 5.0.5033 the most current version? I checked the box to download the latest Windows support software and also didn't find anything newer than 5.0.5033 to download, but sometimes I read about 5.1.1 - but where could I download it? AND: Doest it help?
    Thanks in advance!

    I think I've hit a variation on the problem you're enoucntering.  I have a late-2013 13-inch Macbook Pro Retina.  I've just installed Boot Camp and a copy of Windows 7 Pro.  This is my first experience with Boot Camp and Windows on a Mac, so I'm in foreign teritory.
    The install all went fine and Windows 7 booted up fine and so far, all hardware seems to be working as expected, with one exception.  Things went sideways when I tried use it in "clamshell" mode - lid closed with external monitors and all my peripherals attached to a USB hub.  I set up Boot Camp to boot into Windows and attempted to boot.  It would give me the usual boot-up fanfair and a then a gray screen for a few seconds, and then it would reboot.  It just rebooted over and over.   I eventually discovered the issue was the USB hub - without the hub connected , it would boot just fine.  Once it was booted into Windows, I could attach the the hub and everything would be recognized normally.  Furthermore, I could put the system in sleep mode, wake it up and everything would be working fine.  But it simply refuses to boot the USB hub attached.  I've stumbled on a couple related threads - see https://discussions.apple.com/message/23802231#23802231.  The suggestion is that only certain hubs to not work.  I've got two different high quality powered hubs and both display the same behaviour.  The other point is, that when booting into OS X with the same hub, it works perfectly.  So it's a strange problem.
    Note that after reading your post, I did try the hub in both right and left USB ports and that made no difference in my case.  I do have one more hub to try (built into my Dell monitor).  I'll report back if that happens to work.

  • After upgraded ios6 i got problem with whatapp. "last seen" function is not working

    HI eveyone
    after upgraded ios6 i got problem with whatapp. "last seen" function is not working .. it's doest show last seen who enter the chat . is anyone have the same problem .. i even restore and reinstall to my ph but it's  not work .. if someone know how to fix it, plz tell me how to do .. thanks

    Also, when I check this post several times a day, I always see warning 'Connection is untrust'. If I close browser and reopen immediately everything is ok.

  • Crystal report 8.5 export to csv and rtf format not working with office 2013

    Hi Experts,
    Crystal report version 8.5 hangs and eventually crash when i export my report to csv or rtf format on windows 7 with office 2013 installed, code is written in VB 6 although the same scenario is working with office 2010 installed.
    i debugged the code and found the application hangs at function Report.Export(False).
    below is the code snippet
           .PDFExportAllPages = True 'ePDFExportAllPages
           .PDFFirstPageNumber = ePDFFirstPageNumber
           .PDFLastPageNumber = ePDFLastPageNumber
           .RTFExportAllPages = True 'eRTFExportAllPages
           .RTFFirstPageNumber = eRTFFirstPageNumber
           .RTFLastPageNumber = eRTFLastPageNumber
           .UseReportDateFormat = eUseReportDateFormat
           .UseReportNumberFormat = eUseReportNumberFormat
           .UseReportNumberFormat = eUseReportNumberFormat
           .XMLAllowMultipleFiles = eXMLAllowMultipleFiles
           .XMLFileName = eXMLFileName
           Report.Export (False) ----Application hangs here and eventually crash
    Looking forward for your help, as it is very urgent
    Regards
    Mohit

    Hi Mohit
    CR 8.5, being about 15 years old, does not support Windows 7. I am surprised this works for you with MS Office 2010 and to be honest, I'd consider my self lucky there. The fact that is does not work with office 2013... well, like I said, lucky with Office 2010 and your luck ran out with Office 2013.
    Your option; rewrite the app in VS 2010 / 2012 / 2013 and use the CR Assemblies for VS .NET from SAP Crystal Reports, Developer Version for Visual Studio .NET. The CR Java SDK would be another option.
    - Ludek
    Senior Support Engineer AGS Product Support, Global Support Center Canada
    Follow us on Twitter

  • Nokia e72 push mail not working plus internet conn...

    i bought nokia e72 yesterday for its free push mail. then i set up my yahoo and gmail account on it. but first problem is that its not working untill i manually sync it and the second problem is my internet connectivity icon always remain on the topleft corner of the screen.. plsease help me out with my problem....this is really annoying.
    many thanks
    Manny Thnanx
    Mohit Jain
    Solved!
    Go to Solution.

    Yup, by TOS I meant terms-of-service
    As far as I know the way it works is that (1) your phone maintains a connection with (one of the) Nokia servers, so that as soon as the Nokia server has anything to say (e.g. "new e-mail"), your phone gets it; and (2) the Nokia servers fetch your e-mails so that (1) can work.
    Now, I don't know how (2) works. In theory the Nokia server should act like an IMAP client, and should be using IDLE in order to fetch the e-mails as soon as the server gets them.
    I don't use Nokia Messaging anymore (I now prefer Profimail on my E75), but for some time I did research a bit on that topic, and noticed that the Nokia server was making an IMAP connection to my e-mails server (fastmail.fm) every 15min, i.e. not keeping it open permanently using IDLE. It may be that during those 15min sessions IDLE was used, and then the Nokia server simply decided to close and re-open the connection. That may sound illogical, but perhaps it's more reliable this way.
    In any case, I was getting my e-mails on the phone instantly, i.e. the reconnection every 15min had no impact on the actual push delivery.
    Apparently there are many people having problems with Nokia Messaging. I don't know if Gmail or Yahoo allow you to see a connection log, but if they do, please have a look and see if and how often a server from Nokia/Finland is connecting to your IMAP server.
    Also, I would just in case log on on email.nokia.com and make sure that your account is active (the E72 should give you a lifetime subscription, but please double check).

Maybe you are looking for