Monitor LWAP Interface Load with SNMP

I am working on a monitoring system for the WLC. Most of the SNMP objects are fairly easy to understand but I can't find anything that will let us monitor the Ethernet interface load on a LWAP.
We can see the data in the WLC web interface by navigating to All APs > AP Name > Interfaces.
I would have expected to find something in this section of the tree:
http://tools.cisco.com/Support/SNMP/do/BrowseOID.do?local=en&translate=Translate&objectInput=1.3.6.1.4.1.14179.2.2#oidContent
Any help you can offer would be greatly appreciated.

Naturally I found my own answer a few minutes later:
http://tools.cisco.com/Support/SNMP/do/BrowseOID.do?local=en&translate=Translate&objectInput=1.3.6.1.4.1.9.9.513.1.2.2.1#oidContent

Similar Messages

NEXUS 5000: read CPU Load with SNMP

Hallo,
tried to read the NEXUS 5000 cpu load:
cseSysCPUUtilization 1.3.6.1.4.1.9.9.305.1.1.1
but there is a timeout:
Timeout: No Response from 10.100.224.16
Other MIB values readout, like the system value, is ok.
We use snmpv3.
Thanks
ylvie

Hi Ylvie,
There are a few sources for CPU utilisation values from SNMP, the classic
ones from CISCO-PROCESS-MIB:
cpmCPUTotal5secRev     1.3.6.1.4.1.9.9.109.1.1.1.1.6
cpmCPUTotal1minRev     1.3.6.1.4.1.9.9.109.1.1.1.1.7
cpmCPUTotal5minRev      1.3.6.1.4.1.9.9.109.1.1.1.1.8
And a new source in CISCO-SYSTEM-EXT-MIB, cseSysCPUUtilization
(1.3.6.1.4.1.9.9.305.1.1.1). Unlike the averaged values from CISCO-PROCESS-MIB,
cseSysCPUUtilization returns an un-smoothed value and typically shows more erratic
results.so I would recommended the objects from CISCO-PROCESS-MIB
ie. cpmCPUTotal5secRev instead.
Thanks
Afroj

Monitoring Switch Power Usage with SNMP

Hello everyone,
I have searched high and low, and yet I am still confused as to how to do this... Is there a uniform MIB that can be interrogated, regardless of the switching platform? Or are there specific MIB's for each switch family..?

Monitoring overall power usage may depend on platform and software. There are MIBs such as the CISCO-ENERGYWISE-MIB (if you are using EnergyWise), CISCO-ENVMON-MIB (for voltage information), and CISCO-ENTITY-FRU-CONTROL-MIB (for volatage sensor information).

Monitoring Cpu with SNMP

Hello,
I'am trying to monitor the CPU usage with snmp.
I found ssCpuRawIdle.0 but each time I do :
# snmpget -v 2c -c public localhost ssCpuRawIdle.0
UCD-SNMP-MIB::ssCpuRawIdle.0 = Counter32: 0
The answer is always 0.
I think is wrong, there must be value, but I cannot interdstand what.
snmpd is running and I can obtain answer with other request.
Thanks in advance fr your help.
Jacques

I will add this to my queue of SNMP bugs.
Incorrect data like this are because OS X looks like FreeBSD to the Net-SNMP project, but OS X has some new APIs/SPIs/KPIs that deprecate or eliminate those used by FreeBSD in an attempt to be a more secure consumer-oriented OS.
Macs. Lotsa macs. All without SNMP.

Web service interfaces for monitoring Hosts and instances with SAPHostControl, saphostexec and sapstartsrv

Hi All,
I need to develop a monitoring application for SAP system which will monitor both Host systems and instances.
For this I need to collect Host data as well as instance data. In the below links I could find the SAP netweaver
monitoring agents
Monitoring Hosts with SAPHostControl and saphostexec - Infrastructure of the SAP NetWeaver Management Agents - SAP Libra…
Central Monitoring with SAP NetWeaver Management Agents - Infrastructure of the SAP NetWeaver Management Agents - SAP Li…
Administration/Monitoring of SAP Components with sapstartsrv - Infrastructure of the SAP NetWeaver Management Agents - S…
These links tell that CCMS agent is replaced by these agents from SAP Netweaver 7.0 Eph 2.
I found below doc which explains "How to use the SAPControl Web Service Interfaces" exposed by "sapstartsrv" to execute instance specific tasks,
But it does not tells any methods/APIs/webservice interfaces specific to Host system or get OS data using "saposcol".
SAP Control WebService
Similar to this, Is there any API/webservice to retrieve the OS and Host related data??.
Also, Is there any other doc for SAPHostControl or saphostexec similar to sapstartsrv ??
Thanks,
Swapnil

Hi Swapnil,
I too wanted this info and came across these.
Take a look at these urls :-
http://localhost:1128/SAPHostControl/?wsdl
http://localhost:1128/SAPOscol/?wsdl
grep saphost /etc/services
saphostctrl 1128/tcp # SAPHostControl over SOAP/HTTP
saphostctrls 1129/tcp # SAPHostControl over SOAP/HTTPS
Hope this helps.
Cheers
Craig

Interface frozen with images loaded with Loader()

Hi all,
I am trying to create a web app that allows the user to load an image from a local folder and process it with some image processing. I was able to do that with FileReference and Loader.
I am using an asynchronous shader to process the image and it seems that when the image is loaded locally the interface is locked out for a second or so before showing the result. However, if the image is embedded this does not happen and the image is updated instantly with the result.
I don't really understand why an image loaded with a loader has this lag and an embadded image does not... Can anyone help?
Thanks.

Everything was already done
100 fullduplex autoneg to false :
# for i in `ndd /dev/hme \? | grep "read and write" | awk '{print $1}' ` ; do
echo $
ndd /dev/hme ${i}
done
ipg1
8
ipg2
4
use_int_xcvr
0
pace_size
0
adv_autoneg_cap
0
adv_100T4_cap
0
adv_100fdx_cap
1
adv_100hdx_cap
0
adv_10fdx_cap
0
adv_10hdx_cap
0
instance
0
lance_mode
1
ipg0
16
$ netstat -k hme0
hme0:
ipackets 172970 ierrors 77 opackets 106192 oerrors 0 collisions 0
defer 0 framing 36 crc 41 sqe 0 code_violations 0 len_errors 0
ifspeed 100000000 buff 0 oflo 0 uflo 0 missed 0 tx_late_collisions 0
retry_error 0 first_collisions 0 nocarrier 0 nocanput 0
allocbfail 0 runt 0 jabber 0 babble 0 tmd_error 0 tx_late_error 0
rx_late_error 0 slv_parity_error 0 tx_parity_error 0 rx_parity_error 0
slv_error_ack 0 tx_error_ack 0 rx_error_ack 0 tx_tag_error 0
rx_tag_error 0 eop_error 0 no_tmds 0 no_tbufs 0 no_rbufs 0
rx_late_collisions 0 rbytes 199140046 obytes 6676272 multircv 231 multixmt 0
brdcstrcv 1057 brdcstxmt 42 norcvbuf 0 noxmtbuf 0 newfree 0
ipackets64 172970 opackets64 106192 rbytes64 199140046 obytes64 6676272 align_errors 36
fcs_errors 41 sqe_errors 0 defer_xmts 0 ex_collisions 0
macxmt_errors 0 carrier_errors 0 toolong_errors 0 macrcv_errors 0
link_duplex 0 inits 5 rxinits 0 txinits 0 dmarh_inits 0
dmaxh_inits 0 link_down_cnt 0 phy_failures 0 xcvr_vendor 24657
asic_rev 193 link_up 1
So what do you have any idea, about the problem?
The router is 100 Full Duplex w/o autoneg
the errors arrived only on the virtual interface hme0:1, and never on hme0
Fred,

Would like to monitor teaming with snmp

Hello,
I would like to use snmp to monitor the state of teaming/vibe. I can't seem to find much information on the subject in general and none specifically to do with teaming/vibe. Does teaming/vibe have an OID? If not, is there some way I can give it one? It is a java process and I can monitor a process such as java with snmp but I can't differentiate between different java processes such as indexServer and icecore. Any information or links would be appreciated.
Thanks!
Toney.

toneyc,
It appears that in the past few days you have not received a response to your
posting. That concerns us, and has triggered this automated reply.
Has your problem been resolved? If not, you might try one of the following options:
- Visit http://support.novell.com and search the knowledgebase and/or check all
the other self support options and support programs available.
- You could also try posting your message again. Make sure it is posted in the
correct newsgroup. (http://forums.novell.com)
Be sure to read the forum FAQ about what to expect in the way of responses:
http://forums.novell.com/faq.php
If this is a reply to a duplicate posting, please ignore and accept our apologies
and rest assured we will issue a stern reprimand to our posting bot.
Good luck!
Your Novell Product Support Forums Team
http://forums.novell.com/

Monitoring VLANs with SNMP

Can someone remind me how I can monitor a VLAN other than VLAN 1 with SNMP I think it's something along the lines of public@....
Any help would be much appreciated.
Thanks
Jon

The @ represents community string indexing. So if you wanted to get snmp output for VLAN 200 you would do something like this:
snmpwalk -Os -c public@200 -v 2c 10.1.1.1 dot1dTpFdbAddress
Keep in mind the flags I use above are from my specific snmpwalk utility (net-snmp) but you would add the @ to the comm string and then the value to collect the data

Monitoring the Cisco ACE module with SNMP

We use 2 redundant Cisco ACE loadbalancer in our datacenter
The models are ACE20-MOD-K9 with software A2(2.0)
Does anybod know how to monitor the environment (cpu, memory) of such a module with snmp?
We were not able to find an applicable MIB for that module.
The CISCO-PROCESS-MIB.oid (ftp://ftp.cisco.com/pub/mibs/oid/CISCO-PROCESS-MIB.oid) seems not to reflect the correct oid's.
What are the correct oid's for cpu and memory?
Where can I find a detailed documentation for snmp-monitoring the cisco ace module?
thanks

Hi Patrik,
to monitor the ACE I use these two MIB's:
ftp://ftp.cisco.com/pub/mibs/v2/CISCO-SLB-MIB.my
ftp://ftp.cisco.com/pub/mibs/v2/CISCO-ENHANCED-SLB-MIB.my
Example for CPU:
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Normale Tabelle";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:"Times New Roman";
mso-bidi-theme-font:minor-bidi;}
cpmCPUTotalEntry 1.3.6.1.4.1.9.9.109.1.1.1.1
The resource usage and other interesting things you will find with a MIB browser.
Achim

Monitor with SNMP

Hello,
we would like to monitor client connection by webapp with SNMP.
How can i make this?
Wich OID ?
THKS in adv.

Start here:
http://edocs.bea.com/wls/docs81/snmpman/index.html
And then here:
http://edocs.bea.com/wls/docs81/snmp/index.html
~Ryan Upton
pasbien wrote:
Hello,
we would like to monitor client connection by webapp with SNMP.
How can i make this?
Wich OID ?
THKS in adv.

Open Text Content Server Monitoring Agent 5.0 with SCOM using SNMP

Hi All
Got a requirement to integrate Opentext monitoring agent with SCOM 2012.
Can we use SNMP to forward the alerts to SCOM console ? or can we directly monitor opentext content server with some MP's ?
Regards
Madhavi.

That's the point. You cannot discover Windows Computers as Network Devices with SCOM 2012. So sending traps (directly) to SCOM is not possible.
You can think about a workaround like writing the events to the Windows Event Log and grab them with an Event Log Rule/Monitor. Or send the traps to System Center Orchestrator and write an Alert using the SCOM Integration Pack.
Cheers,
Patrick
Please remember to click “Mark as Answer” on the post that helped you.
Patrick Seidl (System Center and Private Cloud)
Website: http://www.syliance.com
Blog: http://www.systemcenterrocks.com

Interface Bug with 2 monitors in LP8

I use 2 monitors tiled vertically to display a large track layout - in 7.2 I'd have to open the screenset and drag the window across to the 2nd screen - once I did this it would stay in place (across the 2 monitors)
I LP 8 I tried the same thing - only when I select a track on the 1st montor the display reverts and redraws the window to only ONE screen - so for now v. 8 is useless -
Also - I find the legibility is MUCH WORSE with this haze of grey over everything - Looks Like I'll be hanging on to my xs usb keys for a while---
back to work, back to 7.2

I work with 2 monitors all the time - with very large arrangements it's a huge boon. Are you saying if for example you have a linked matrix editor open on the 2nd screen every time you change tracks it shhots onto screen 1?
This would be a disaster for my use of Logic so I hope this isn't the case or if it is it's a soon to be fixed bug!
Julian

SCOM Monitoring Multiple interface of a same network device

hi
I have deployed SCOM 2012 R2. I have discovered around 200 network device by using device's loopback IP adress with SNMP v3.
100 dvices are in the branch offices those are connected with 3 links in three interfaces respectively. Even if two link is down, i can see that my network device is healthy since network device is discovered with the loopback address. How can i configure
my network monitoring so that even if one link goes down i can see some kind of warning or error in the particular network device in my monitoring pane. Please say if my infrastructure is unclear.

Hi,
You can create built-in network ICMP only network monitoring for the three interfaces respectively.
Using the built-in network monitoring within Operations Manager 2012 to monitor network devices using ICMP only mode
http://blogs.catapultsystems.com/cfuller/archive/2013/07/03/using-the-built-in-network-monitoring-within-operations-manager-2012-to-monitor-network-devices-using-icmp-only-mode-scom-sysctr.aspx
Note: Microsoft provides third-party contact information to help you find technical support. This contact information may change without notice. Microsoft does not guarantee the accuracy of this third-party contact information.
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

I just installed LV2011 and one dll from my vi won't load with the error "application configuration is incorrect"

I just installed LV2011 and one dll from my vi won't load with the error "application configuration is incorrect", which is Windows lingo for "missing package dependencies". All the computers at my company with 2010 loaded seem to do OK. When I do a Dependencies Walk I get missing Visual C debug dll's missing plus IEshims and wer which both have a whole tree of dependencies missing on my machine. The Windows install is the same "Windows XP version 2002 Service Pack 3" on my PC and the working PC's. So I'm thinking I have to uninstall 2011 and go back to 2010. Is this correct? Those VC debug dll's were installed on the machines with 2010 in them but were not installed in mine.
I've heard the advice to recompile the dll with debug turned off but I don't have access to the source code.
Thanks in advance.

u87 wrote:
Thanks for the reply. This at least tells me that going back to LV2010 is not likely to solve the problem. The missing dll's are:
MFC90D.dll
MSVCR90D.dll
IESHMS.dll
WER.dll
And, once again, IESHMS and WER have other dependencies. So perhaps i need to install the Visual C++ development environment.
IESHIMS.dll is an Internet Explorer DLL that gets usually delay loaded by shdocvw.dll. As delay load it can not cause DLL load errors but only runtime errors. Maybe your DLL has it as direct dependency but that is unlikely since it does not have a documented interface.
WER.dll is Windows error reporting for Vista/Win7.
MFC90D.dll is the Microsoft Foundation classes and MSVCR90D.dll is the MS C runtime library, both as debug variant.
So all the DLLs you mention are actually MS DLLs! You haven't identified the DLL that you try to access in LabVIEW that causes these error messages. IESHIMS and WER are usually delay loaded by any component that needs it and should not likely be used by non MS code.
What is the DLL you try to load into LabVIEW and by whom? Get the provider of that DLL to provide you a non Debug build of the DLL. Installing Visual C on all the machines just to make the DLL load is not a solution, besides that it is likely not legal since I doubt you have that many licenses.
Rolf Kalbermatter
CIT Engineering Netherlands
a division of Test & Measurement Solutions

Is it possible to add a second monitor via mac mini with iMac

Hi
is it possible to add a second monitor via mac mini with iMac
or is there another solution?
all i want to know is if i can run a second monitor or link a mac mini for more speed like i heard you can with the G5 Towers.

The iMac will allow you to connect a second monitor but that monitor will show the same thing as the iMac's built-in screen.
You can network a Mac mini and iMac via Ethernet or Firewire.
Software load sharing like Xgrid can allow you to share work between the Macs.

Monitor LWAP Interface Load with SNMP

Similar Messages

Maybe you are looking for