Monitoring CAN hardware status.

I am trying to display the status of each CAN (network and frame) object that I have configured in a C++ application. We are required to support both Series 1 and Series 2 cards.
I tried to extract the status from the NC_ATTR_STATE attribute. It displays the correct state most of the time. Unfortunately, the returned state does not seem to be returning consistent values. I have two CAN channels connected with terminating resistors. I start transmitting on both channels. I disconnect the cable. The state that is returned is mostly 0x20 (NC_ST_WARNING) but occasionally the state 0x02 NC_ST_WRITE_SUCCESS is returned. How can a write be successful if there is no communication?
Is there any other way to monitor the hardware status that works on both Series 1 and Series 2 cards?
Thanks in advance.

Hi scottw,
take a look a the description of the desired state: NC_ST_WRITE_SUCCESS
"When communication starts, the NC_ST_WRITE_SUCCESS state is true by default."
and
"The state is set when the last frame in the write queue is transmitted successfully. The state is cleared when a write function is called."
Thus, you could see a NC_ST_WRITE_SUCCESS state, even though there is/was no communication.
-B2k

Similar Messages

Monitoring Hardware Status HP ESXi with HP SIM, Get information by SNMP

Hi.
Check out to tring this steps http://h30507.www3.hp.com/t5/Technical-Support-Services-Blog/6-Simple-Steps-to-Monitoring-ESXi-with-...
It's ok, I having health hardware status for the server in the HP SIM 7.3 by wbem with Custom HP Image ESXi 5.5 onboard by wbem .
Did any solution to get health status from hp server ESXi or from HP SIM 7.3 by SNMP to another monitoring software?

Have now solved it myself:
1) Create system restore point
2) Uninstall mobile broadband driver and centrino ultimate-N in device manager, but keep files
3) Reboot
4) Lenovo access connections automatically connects to mobile broadband. It's then just a matter of going in there and connecting to wifi also.
Everything is working beautifully now, and switching between wifi and mobile automatically. I think it was just corrupted TCP/IP settings in one or both adaptors.
X230, Core i7, 16GB memory, 512GB Samsung 830 SSD

Need help in Solution Manager System Monitoring-activating Instance Status

I would like to use System Monitoring with Solution Manager.
The agents CCMSPING and SAPCCM4X are installed on the monitored system and CCMS is configured
I've already created a solution and a logical component. Now i would like to activate Instance Status in the tree when i enter in Setup System Monitoring .... but i get a red alert an the following Message Instance status is no performance alert. Thresholds have been deleted ... how can i activate this Instance Status?
I am going my first steps in SAP SolMan and tried to solve this problem but i had no success. Can someone please help me? What i am doing wrong?
thanks...
Edited by: Satish Machavarapu on Dec 15, 2009 12:46 PM
Edited by: Satish Machavarapu on Dec 15, 2009 1:04 PM

Hi,
If you want to monitor the Availability status of the instance then check the below docs
[http://help.sap.com/saphelp_nw70/helpdata/EN/38/9e100dd7980fffe10000009b3810a5/frameset.htm]
[CCMSPING config|http://www.sdn.sap.com/irj/scn/elearn?rid=/library/uuid/d547f687-0901-0010-07a9-ce64cc044215]
[CCMS Agent config|http://www.sdn.sap.com/irj/scn/elearn?rid=/library/uuid/40ef0688-814a-2a10-afb1-89b40d83d0e0]
regards
Naveen
Edited by: Naveen Kumar on Dec 15, 2009 1:07 PM

ON RWB - CC Monitoring - SOAP Channel. status says "inactive or unregister

Hi,
I am working on SOAP Webservices.
My Scenario is working fine ... But Some How on RWB - CC Monitoring - SOAP Channel. status says "inactive or unregistered".
On the otherside , my SOAP Scenario is working fine...
But why for that status " "inactive or unregistered"." , I dont Know?
Please Suggest, How to Deal with this ........?
I executed transaction code " se38 - > SRT_ADMIN_CHECK report "
It states me almost every thing unregistered/ inactive/ not configured except ICM Services ..
are these services shoud active and registered for SOAP Scenario?
how to activate them .............????????
That CC status " "inactive or unregistered" has anything to do with this SRT_ADMIN_CHECK report????
Regards
Prabhat Sharma.

Hi
This is the problem which i recently faced and solved.
Cause: Saop related J2EE application are stoped or not set to default start as initial state.This is also a reason
             for 503 service unavailable error while soap posting.
Solution : start the J2EE app , com.sap.aii.adapter.soap.app & com.sap.aii.adapter.soap.lib set them as defualt started
               as initial state.
Where : If you are in PI 7.1 , http:<host>:<port>/nwa->Operations Management -> Systems -> Start & Stop -> Java EE
               Applications.
                Refer http://wiki.sdn.sap.com/wiki/display/XI/start_stop_applications for more help.
               Also in Start button , there will be a dropdown where you can set the default initial state as started.Simply starting may
               cause similar problem ( not registered ????????) again ,so better to set initial as started state.
Regards,
$rinivas

Monitoring TCP port status

I would like to know if a tcp port is open or not. How can i do it ?

Hello IDS,
Thank you for contacting National Instruments.
I have created an example VI that expands on Stijn's response. The TCP listen will return IP and port information if the selected port is open. If it is not, the VI will time out and send an error. By putting the TCP Listen VI in a while loop and monitoring the error status, you can monitor the status of the TCP port.
You can adjust the timeout according to your needs.
I hope this helps,
Sean C.
Applications Engineer
National Instruments
Attachments:
ExampleVI.vi ‏26 KB

Server Monitor Notifications - Drive Status Changed - Time Machine

I'm using an Xserve as a file server for a small workgroup . It has a Raid 1 set which is being backed up via Time Machine to an attached disk array.
Whenever Time Machine runs (every hour), I get two notifications from Server Monitor that the drive status has changed:
*Reason(s) for notification:*
*Drive status changed*
The timestamps on the notifications coincide with these messages in system.log
Feb 2 11:28:05 ciesaxserve2 Server Monitor[854]: * _NSSocket.m:243 read() failed; socket=0x197060 error=(NSPOSIXErrorDomain,61)
Feb 2 11:28:05 ciesaxserve2 Server Monitor[854]: * _NSSocket.m:243 write() failed; socket=0x197060 error=(NSPOSIXErrorDomain,61)
Feb 2 11:28:05 ciesaxserve2 Server Monitor[854]: * _NSSocket.m:243 read() failed; socket=0x2090e90 error=(NSPOSIXErrorDomain,61)
Feb 2 11:28:05 ciesaxserve2 Server Monitor[854]: * _NSSocket.m:243 write() failed; socket=0x2090e90 error=(NSPOSIXErrorDomain,61)
and:
Feb 2 11:28:55 ciesaxserve2 servermgrd[78]: servermgr_backup: TimeMachinePostBackupHook called.
Feb 2 11:28:55 ciesaxserve2 servermgrd[78]: servermgr_backup: TimeMachinePostBackupHook done.
The notifications simply report that all is normal, and the number of available drives goes from 6, to 7, back to 6. Something to do with making the backup volume available, I presume.
I would like to disable these specific messages. I realize I can disable all messages from server monitor regarding disk statuses, but then I would be turning off messages about failures and actual problems.
Is there a config I can edit which will only alert me to actual problems? I'd like to stop getting 48 emails each day; reduce the noise and increase the signal.

I know this post is old but this has recently cropped up for me. I have been backing up with Time Machine for months without a single alert. It started happening after I replaced the failed battery on my RAID card. A coincidence...however the prolonged down time surely caused an SMC (and perhaps PRAM) reset which I assume triggered the change in behavior.
I've pinned it down to Time Machine backing up service settings, in particular the Open Directory archive. Time Machine backs up all the service data independently from the rest of the data on your server startup volume.
http://support.apple.com/kb/ht5139
You can see this data in Terminal.
serveradmin$ cd /Volumes/[YourBackupVolume]/Backups.backupdb/[YourServerName]/Latest/[YourBootVolume]/.ServerBackups
serveradmin$ ls -al
total 16
drwxr-xr-x@ 2 root admin    68 4 Jun 14:44 (null)
drwxr-xr-x@ 14 root admin   476 4 Jun 14:44 .
drwxrwxr-t@ 43 root admin 1462 4 Jun 14:43 ..
-rw-r--r--@ 1 root admin    37 4 Jun 14:44 .serverBackupSignature
drwxr-xr-x@ 2 root admin    68 4 Jun 14:44 addressBookServer
drwxr-xr-x@ 2 root admin    68 4 Jun 14:44 calendarServer
drwxr-xr-x@ 5 root admin   170 4 Jun 14:44 iChatServer
drwxr-xr-x@ 6 root admin   204 4 Jun 14:44 mailServer
-rw-r--r--@ 1 root admin 3826 4 Jun 14:44 master.browse.plist
drwxr-xr-x@ 4 root admin   136 4 Jun 14:43 openDirectory
drwxr-xr-x@ 61 root admin 2074 4 Jun 14:44 serverSettings
drwxr-xr-x@ 23 root admin   782 4 Jun 14:44 sharePoints
drwxr-xr-x@ 8 root admin   272 4 Jun 14:44 webServer
drwxr-xr-x@ 2 root admin    68 4 Jun 14:44 wikiServer
If you take a look inside the openDirectory folder you should see this:
serveradmin$ cd openDirectory
serveradmin$ ls -al
total 81936
drwxr-xr-x@ 4 root admin       136 4 Jun 15:32 .
drwxr-xr-x@ 14 root admin       476 4 Jun 15:33 ..
-rw-rw----@ 1 root admin 41947136 4 Jun 15:32 ServerBackup_OpenDirectoryMaster.sparseimage
-rw-r--r--@ 1 root admin       249 4 Jun 15:32 openDirectory.browse.plist
The ServerBackup_OpenDirectoryMaster.sparseimage contains an archive of your Open Directory database like the one you create from Server Admin. The only difference is that it appears to be unencrypted. This is a bit worrying since Snow Leopard, as far as I know, does not have an option to encrypt your Time Machine backup. This image seems to invisibly mount whenever a Time Machine backup is triggered. This can be verified by checking /private/var/log/system.log and filtering for backup
serveradmin$ tail -b 100 /var/log/system.log | grep backup
Jun 4 16:00:56 yourservername com.apple.backupd[25117]: Starting standard backup
Jun 4 16:00:56 yourservername com.apple.backupd[25117]: Backing up to: /Volumes/YourBackupVolume/Backups.backupdb
Jun 4 16:00:56 yourservername servermgrd[75]: servermgr_backup: TimeMachinePreBackupHook called.
Jun 4 16:09:26 yourservername servermgrd[75]: servermgr_backup: TimeMachinePreBackupHook done.
Jun 4 16:09:44 yourservername com.apple.backupd[25117]: No pre-backup thinning needed: 4.60 GB requested (including padding), 8.40 GB available
Jun 4 16:10:14 yourservername com.apple.backupd[25117]: Copied 744 files (364.4 MB) from volume YourBootDrive.
Jun 4 16:10:14 yourservername com.apple.backupd[25117]: No pre-backup thinning needed: 4.09 GB requested (including padding), 8.04 GB available
Jun 4 16:10:17 yourservername com.apple.backupd[25117]: Copied 87 files (877 KB) from volume YourBootDrive.
Jun 4 16:10:18 yourservername servermgrd[75]: servermgr_backup: TimeMachinePostBackupHook called.
Jun 4 16:10:18 yourservername servermgrd[75]: servermgr_backup: TimeMachinePostBackupHook done.
Jun 4 16:10:18 yourservername com.apple.backupd[25117]: Starting post-backup thinning
Jun 4 16:10:29 yourservername com.apple.backupd[25117]: Deleted backup /Volumes/YourBackupVolume/Backups.backupdb/yourservername/2013-06-03-155910: 8.40 GB now available
Jun 4 16:10:29 yourservername com.apple.backupd[25117]: Post-back up thinning complete: 1 expired backups removed
Jun 4 16:10:29 yourservername com.apple.backupd[25117]: Backup completed successfully.
You can see at 16:00:56 Server Manager got a call from Time Machine to start the services backup and finished at 16:09:26. Open Directory would have been backed up during that process. Take a look at /private/var/log/hwmond.log
serveradmin$ tail /private/var/log/hwmond.log
Tue Jun 4 16:08:36 BST 2013 - Number of drives change from 4 to 5.
Tue Jun 4 16:08:48 BST 2013 - Number of drives change from 5 to 4.
You'll see that both drive change warnings from Server Monitor occured just before the services backup completed. You can also use the sudo diskarbitrationd -d command along with tail /private/var/log/diskarbitrationd.log in another terminal window, trigger a Time Machine backup manually and watch this disk image mount during the backup process. Compare the mount times with the above logs to see if they all match up.
Although I have discovered the cause (which thankfully seems harmless) I have not discovered a way to stop it from generating pointless alerts. I'll post here if I figure it out. I am in the process of upgrading all of my servers to Mountain Lion so it may be a moot point. I am hopeful this information may help someone out there even though it is thoroughly out of date.
Scot

How do I monitor internal hardware temperatures?

I have a MBP about 2.5 years old. I used to use Temperature Monitor to monitor internal hardware temperatures, but MacUpDate says it no longer works under Yosemite. When I try to use it, I get an error message about resources missing. What can I use to monitor these temperatures? Is there something in Yosemite that can report these, or do I need to buy a third party app (if so, which one)?
Thanks
Claude

You can try with iStat Pro widget.

Is there is any way to find the data transfer from client to Configuration Manager for health monitoring and hardware Inventory

Hi
Can Configuration Manager provide a way to find the data transfer from client to Configuration Manager for health monitoring and hardware Inventory. How can I know what amount of data is consumed during that process

Place archive_reports.sms in %systemroot%\ccm\inventory\temp\ for both 64-bit and 32-bit computers.
There are two situations where you can use this depending on the type of client:
1. To keep inventory reports on a client (that is not an MP), create the following file:
%systemroot%\ccm\inventory\temp\archive_reports.sms
2. To keep inventory reports on a MP (that is also a client), create the following file:
<x>:\sms_ccm\inventory\temp\archive_reports.sms
The XML file will be saved in the inventory\temp folder.
More information on the above here: http://blogs.technet.com/b/configurationmgr/archive/2012/09/17/controlling-configuration-manager-2012-using-hidden-files.aspx

I have a new macbook pro and an LG w2361v monitor. The max resolution the mac is allowing me to set is 1400x1050, why can't I get to the max resolution the monitor can accept (1900x1080)

I have a new macbook pro and an LG w2361v monitor. The max resolution the mac is allowing me to set is 1400x1050, why can't I get to the max resolution the monitor can accept (1900x1080)? I know that the monitor is able to accept this resolution but It can't seem to find it. Is it something to do with the new thunderbolt port? or the fact that I'm utilizing the VGA adaptor? I could go HDMI if that works better.

Use DVI or HDMI.
VGA runs out of steam after a while.

Server Monitor can't see server

Machine and OS specs:
2 x 2GHz Dual Core Intel Xserve using 1 x ethernet port
OS X 10.4.10
I have just installed a new Xserve set up with mirrored RAID drives which is working perfecty apart from the Server Monitor will not connect just giving the message 'waiting for response'. I have tried all the various admin and root passwords and even tried to connect from my older G4 Xserve with the LOM password, but get the same result. All other administration software works fine.
I have searched various forums and advice sites, but the suggestions I've found have not worked. I read that the com.apple.hwmond.plist can be edited to <false/> from <default/>, but when I open the file in a text editor I get this:
<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE plist PUBLIC "-//Apple Computer//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd">
<plist version="1.0">
<dict>
<key>Label</key>
<string>com.apple.hwmond</string>
<key>OnDemand</key>
<false/>
<key>Program</key>
<string>/usr/sbin/hwmond</string>
<key>ProgramArguments</key>
<array>
<string>hwmond</string>
</array>
<key>ServiceIPC</key>
<false/>
</dict>
</plist>
- already set to <false/>!
When I try to connect to the server via it's Terminal by typing ssh -l adminuser (my IP address) I get the message: 'The authenticity of host '(my IP address) (my IP address) can't be established'. This leads me to think something else is up. I can ping it OK.
I have tried pretty much everything I can think of including manually setting IP addresses etc, but I would really appreciate any help or advice with this one.
Thanks.
G3 • G4 • G5 • Intel - You name it! Mac OS X (10.4.10)
G3 • G4 • G5 • Intel - You name it! Mac OS X (10.4.10)
G3 • G4 • G5 • Intel - You name it! Mac OS X (10.4.10)

Hi
On the XServe launch Server Monitor, select Add Server and in the IP Address field key in 127.0.0.1 or localhost. In the Name and Password fields key in the default System Administrator account details. Click on Save password in keychain and select a suitable Update every settiing. If you launch WGM you will see the System Administrator account already listed in the local NetInfo node (UID 501). Use the short name as listed in WGM.
Although I have not had the chance to do this yet, but enabling Lights Out Management (LOM) opens port 623 which Server Monitor can use. This may allow for remotely using Server Monitor to monitor the XServe.
Hope this helps – Tony

How big an external monitor can i plug into the X60?

I will be running Serato Scratch Live SL3 DJ software on my X60 and it would be nice to have a little extra sceen area for the display. How big of an external monitor can I plug into my X60? What can the built in graphics card handle?
Thanks!
(best notebook I have ever owned btw! light, strong, stable)

i have tried 24 inch with WUXGA resolution.
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

In production order can the status of TECO ,in menu bar can be deactivated

Hi
In production order can the status of TECO /REVOKE TECO in menu bar can be deactivated .if it can be done where to do the setting and what is it implications
regards
madan

Hi Sarvan,
We are using the version ECC6.0. I want the authorisation of "revoke close" for some of the users only. Is it possible? If yes, what exactly is the authorisation object.I did not find any object as SAP-Security.
Is it possible to control it by any user exit.
Kindly let me know ASAP.
Regards,
Satyajit

How to identify the CAN hardware connected to the PC

Hi
Is there any way to identify the CAN devices to the PC via USB port, I am able to see the connected CAN hardware name in the device manager list. Same I would like to read using LabVIEW.
Regars
Visuman
Solved!
Go to Solution.

Use the vi in the zip file.
And the "Devcon.exe" will show you the device list.
With this list you may sort out the devices bei searching the string.
Attachments:
Device Managing Folder.zip ‏24 KB

How many monitors can be connected?

1. How many monitors can be connected to a SIngle (1) Thunderbolt? Any Specific size of monitors?
2. How many monitors can be connected to a Double (2) Thunderbolt? Any Specific size of montiros?
3. I've came through a post mentioning that, a maximum of 6 CHAIN DEVICES can be connected to the 2 thunderbolt. Could you please give me an example??

I want to connect 6 vga or dvi monitors.
I'm sorry, translation via google translate
Mac pro ordered, paid money. Now I worry that I won't be able to connect 6 vga monitors. I already have 6 vga of monitors, don't want to buy 6 thunderbolt monitors
thanks!!!
PS VGA adopters are all active. It means mac pro supports six vga monitors?

Which own monitors can I add into DAs

Hi!
I want to clear out the question on which own created monitors can I add into Distributed Applications? For example:
I can find all monitors that I have created through Management Packs Template and add it into my DA if the monitor is from a sealed MP or in the same unsealed MP as my DA.
I cannot add any monitors that I have created through Management Pack Objects/Monitors/Unit Monitor into any DA. Why?
//Mats A

Yes I understand that but for example:
I creat one monitor Management Pack Objects/Monitors/Unit Monitor/Windows Event/Simple Event Detection/Manual Reset
       - Name on the monitor is Approved_ID222_Event
       - Save this monitor in Approved_Monitoring
MP
Create one DA
       - Name on the DA is Approved
       - Save this DA in Approved_Monitoring
MP
       - Try to find my monitor Approved_ID222_Event
through Advanced Search. Cannot find my monitor
//Mats A

Monitoring CAN hardware status.

Similar Messages

Maybe you are looking for