My HP Pavillion A6700y will not power on after power surge

Got home today and the computer was turned off, was told there was 2 power surges today. I can push the power button, it turns on but blue power light doesnt, I can hear the fans turning on and being really loud but nothing comes up on monitor. Opened the case my power supply's fan (bought a few months back) turns on, same with the video card fan and the fans on the board. Anyone have any ideas to what could be wrong? Thanks

Big_Dave wrote:
Removing the power strip is a fairly common elimination practice and not a speculation practice....
The Thermaltake power supply tester is an example of using the correct tool.
To cause a failure, that power strip must reduce voltage so low that a connected incandescent bulb dims to less than 40% intensity. Removing a power strip implies basic electrical concepts are missing. A perfectly normal voltage for all computers is even when incandescent bulbs dim to 40% intensity. If any power strip causes that voltage reduction, then the power strip is also hot and obviously dangerous.
Normal is for a defective power supply to be reported good by a power supply tester. That tester cannot report a long list of potential defects. For example, it provides a near zero (insufficient) load. It does not report numbers that report on other potential defects. It does not test other components of the power system. It costs almost as much as a meter that reports on so many other possible defects - and more. Those who better know this stuff can provide little assistance without numbers from that meter. Numbers are essential.
Best that tester can report is, "maybe a supply is good". And say nothing about other power system components.

Similar Messages

HP Pavillion dv6000 laptop computer will not power on

My HP Pavillion dv6000 laptop computer (s/n CNF72132WJ, p/n GH783EA#ABU) will not power on - it gives 1 long beep followed by 3 short beeps and then does nothing. I've been told that the problem is the NVIDIA graphics card but am unable to find this part in the HP Parts Store. Is the NVIDIA graphics card a separate purchasable item for an HP Pavillion dv6000 laptop computer or is it integrated into the system board (p/n 443774-001)?
Where in the UK can I purchase either a replacement NVIDIA graphics card or a replacement system board (p/n 443774-001)?
Thank you in advance for any help you can give me with this problem.

The Nvidia graphics card is soldered on to the motherboard and you need to replace motherboard for the Notebook to work according to your diagnosis.
The Part# - 443774-001 is Out of stock and curent not available in HP Parts store however I just did a search for you on Ebay UK website and was able to find it in search results over here
//Click on Kudos and Accept as Solution if my reply was helpful and answered your question//
I am an HP employee!!

HP Pavilion dv6000 will not power up.

I have had an HP Pavillion dv6000 for a few years, and suddenly, it will not power up at all. I can not determine that anything at all happens when I press the power button. What's weird is that when I connect the power, the AC LED (the one with the lightning bolt above it) lights, and stays lit for 30 seconds, and then turns off. During that time, and thereafter, the power light will not come on at all, and the computer will not power up. I have tried removing the battery and power cord and holding the power button for 45 seconds, multiple times, but nothing seems to work. I hope you can offer some advice on things to try.
Thanks,
Zach
This question was solved.
View Solution.

Well, I've had the problem for a while and was just looking around to see if anyone has had any success stories.
I will tell you how I get mine up and running, but first some background. I was gifted this computer DOA and asked to retrieve data which I was able to do but in monkeying around, I discovered a "fix".
You see, I live in an area where we occassionally lose power for a day or two or three so the weakened battery never outlasts the outage. That's when the unit becomes unstartable.
Now the fix:
It is a variation of all the other suggestions about undoing the power cord and disconnecting the battery but here's the twist: After removing the battery and power cord, wrap your laptop in one then another plastic shopping bag and place it in the freezer for about an hour or two. Now, when you take out your shivering laptop, plug in the power cord and fire her up. It has nearly always started for me after this trial by cold but once or twice it needed more chillin'. Once it is started, insert the battery. I've never had any issues with this sequence.
You will have a lot of condensate on the screen but gently wipe it up with an absorbent cloth and let the rest of air dry as you let it run.
As long as I leave the computer plugged in and not reliant on the battery, it has never died on me.
Hope this helps!

DV4 1275 Power Issue, Battery not charging, Will not Power with AC only

HP Pavillion DV4-1275mx
Battery will not charge, Laptop will not fully turn on with battery in (battery not charging at all). Laptop will not power on at all with no battery using only AC and with battery it will attempt to load and die due to lack of charge.
Have tried 3 diff HP chargers.
The orginial 1 that came with the laptop is dead and will not charge anything. Tried it on a diff HP laptop and not recognizing any power
The 2nd one is OE HP laptop diff model but same wattage that came with my gfs work laptop. I have charge my laptop with it before in the past however it is not charging the battery now either
The 3rd is a aftermarket generic one that my g/f bought in the airport and it works with hers as well however I have never used it on mine.
I have tried hard resetting.. taking out battery, holding power for a min and replugging everything.
Also when I remove the battery and plug in either of the chargers that do work the power LED are "not" lighting up on the front or the LED where the AC plugs into the laptop. Which makes you think the charger is bad however the 2 working chargers do work on my other 2 HP laptops.
If i plugin one of the 2 working chargers with the battery it will go through the boot process and as its starting windows it just dies and shuts off. The power led by the DC jack does light up and the charging light on the front lights up. However this only works when I unplug the battery and plug the AC charger in. After the laptop boots up to starting windows and dies. I have to remove the battery and replace it to get the LEDS to light back up.. If the MB was bad I wouldnt think any of the LED's would come on nor would the laptop boot up to the starting windows. If keep trying to turn it on the booting time is shortened as the battery is not holding a charge and sometimes it only makes a few seconds and then just dies out.
I dont have alot of money to spend so I was hoping maybe you could point me in the right direction.
Should I buy the replacement part OE charger for my specific laptop? (not sure if its going to be much diff than the others since they are all 65 watt chargers)
Should I buy a new battery as well?
Or does this sound like a short problem in the mother board or a solder issue with the DC plugin?
If it is an issue with the motherboard I do not want to go through the hassle of buying the battery and charger as I will end up having to just replace the laptop
If you could please advise me what direction to go I would be so greatful.

Dude, I have the same exact problem with mine. It's not a cheap fix either. It definitely is the motherboard.
I'm no expert, but I believe the problem is a dead capacitor on the motherboard preventing it to build up a charge.
I spoke with an HP rep, which told me it's $398 for them to fix.
I let them know that I didn't have another $400 to put into this laptop. So, they suggested I try reseating the motherboard. And also reseating the memory modules.
http://h10032.www1.hp.com/ctg/Manual/c01597750.pdf
That is a pdf of the laptop's manual. It'll help in reseating. Page ( 59 ) for the motherboard. Page ( 67 ) for the memory modules.
This hasn't helped at all with mine, but maybe it'll help with yours!

My Powerbook will not power up, but I can hear the fan running...

Please help!! My Powerbook will not power up, but I can hear the fan running when I press the power button to attempt to power it up. I just received a new power adapter because it wasn't working properly and it was doing this before and then it worked for a week and now it will not power up at all. It just starts the fan but nothing else turns on. When I plug the adapter, with the battery still connected, it will look as if it is charging but then the light on the plug turns from green to orange then off and doesn't power up at all. If I take the battery out and plug in the adapter, the light stays on but it does not power up except for the fan noise. Does anyone have any suggestions? I also followed the two articles listed online in regards to resetting the power setting and the command + alt + P + R as well. Nothing works. Thanks in advance.....

Same here. If I start up with the power adapter attached, it starts up fine. If I try to start up from battery only, the fan comes on, the sleep light comes on but nothing else happens. I tried letting it sit that way for about 15 minutes and nothing changed. I tried attaching the power cord while in this mode and nothing changed. I tried the PMU reset a couple of times but nothing helps.
This computer is just over 1 year old and I have not had any problems with the power cord (3rd party), the battery, or any problem like this before. It started after a proper shutdown last night and attempt to start without the power cord this afternoon.
Any answers to this yet? I think I'll call on this and report any success to this discussion.
15" PowerBook G4 Mac OS X (10.4.8) 1 GB DDR2 SDRAM, 100 GB HD

Need Help HP DM3 (DM3-1130us) Laptop will not power on. No power at all except for light on a/c jack

Hello, I need some help.
I have a HP DM3-1130us Laptop that will not power on at all.
the only thing that happens when I plug it in is the power jack lights up.
When the power button is used absolutely nothing happens.
No power, no fans, no leds, no on/off cycles, no beebs, absolutely nothing
just the light by the power jack that says the cord is plugged in.
The laptop has Windows 7, 320gb hdd, 4gb ram.
I have tried new power adapter and still nothing.
I have taken the battery out and tried and nothing.
I've tried the option where you take the battery out and hold the power and nothing.
I have tried with different hard drive and no hard drive and nothing.
I have tried reseating the ram and tried new ram modules still nothing.
So I am kind of stumped on what to do, the laptop will just not turn on.
Its not under warranty anymore so cant send it off.
It has not been exposed to any elements(extreme heat or water).
and its never been dropped or anthing.
Im kind of wondering maybe the power button board its self is bad?
If feels fine, its not loose or anything but could it
have just stopped working? for those who are not familiar with this model.
the power button is on the side and is a kind of drag and release button.
Its also on the same board with the Wifi button and 2 Usb ports.
But Im wondering before I buy a new one if this is what it could be.
Or could the motherboard its self be bad?
But even if the motherboard is bad would it still power up
just not post?
Also does anyone know of any other way to try to power this laptop up
without using the slide button. I mean kind of like off a Dv6000 you can power the laptop on by using the Quicklaunch buttons on top but this laptop does not have those.
If anyone can provide any information I would appreciate it.
Thank you.

Hey Tyler,
Unfortunately it is difficult to troubleshoot this type of issue. The majority of the time when the computer wont power on with the same symptoms you described, the power supply board is faulty. Most of the time if the motherboard is bad it should at least turn on or so some signs of life. Like I said, this is most of the time. Sometimes it could do exactly what your experiencing. I would suspect the power supply board has failed since you are not receiving any sort of lights, sounds, etc.
You could check the motherboard for swollen capacitors or loose solder joints but sometimes you wont be able to find anything.
I hope this helps answers your questions,
Sean
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

My iPhone 5s will not power on and I need my serial number for support.

I am attempting to get help through Apple Support- Chat, but I need my serial number. It is not showing up in iTunes under the device preferences. Any other ways to retrieve the serial number through iCloud?
If anyone has any idea of what is going on with my phone, I would love some assistance. I live 45 minutes from the nearest Apple Store. Here's the situation:
About 2 weeks ago, my phone started shutting itself off and restarting randomly.
About a week and a half ago, I would randomly get a blue screen and then the phone would restart multiple times.
About a week ago I turned off Touch ID in an effort to resolve the issue, after reading some fixes from this community. That seemed to help. I do have the animation turned off, so I had read that there may be an issue between the Touch ID and animation reduction. If that had not helped, I was going to turn the animation back on.
Last night my phone seemed fine. I did hear it restart in the middle of the night once, but this morning it will not power on at all.
I tried connecting it to my computer through iTunes, but iTunes does not see it and I cannot access the device information from it.
My phone is less than a month old, and for the first two weeks it worked great. I am taking it into the AT&T Store today where it was purchased, but I don't really have high hopes for a resolution.
Any help is much appreciated!

Sorry AT&T store won't be much help.
I suggest you make an appointment with the Genius bar and then go to the Apple store.

Macbook Pro will not power on without battery installed

Hi there,
I have a Macbook Pro A1226 that fails to power on without a battery installed.
i.e. will not run off AC power on its own. I have tried 2 other power adapters, no change. All 3 adapters are outputting the correct voltage without fluctuations.
But, if I am in OSX with a battery plugged in, shutdown the laptop, remove the battery while AC is still plugged in, it will power back on without any issues. But as soon as I remove the battery, it will not power back on using just AC.
Is this an I/O board issue, or a mainboard?
I have power drained the unit and reset the parameter ram.
Thanks

Any update on this? This is the same thing that's going on with my laptop right now. I was at the Genius Bar and they said they can send it in for repair. Takes 7-9 days and costs a minimum of $310. At the time I was there, my computer wouldn't start up at all, because the battery had drained to less than 20%. It didn't even start with just the power cord (no battery in). The "genius" finally got it to work by doing a PRAM and SMC reset. Got home and was able to recharge my battery to 100%. Used my computer for 2 days before I dared to take it off the power supply. Lo and behold, as soon as I take it off the power cord, then re-connect it, it shows "Not Charging". I tried to do SMC again, but no luck. Keeps saying "not charging". Even tried with a brand new battery. Do I have to get the I/O board thingy replaced?

Ipod touch generation 5 will not power on

My ipod touch generation 5 will not power on though it was showing to b e fully charged. I have been pressing and holding the on button on the top which usually cause a the screen to light up. Is there some way to get it to work?

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

My ipod touch will not power on or even be acknowledged by my computer when i plug it in, any suggestions to the problem

My Ipod will not power on, it is fully charged and if I plug in into the computer it doesn't even ackowledge it. Any suggestions?

Try a hard reset and go from there.
Basic troubleshooting steps.
17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G + 120G OCZ Vertex 3 SSD Boot HD 

My IPOD Touch initially had a white screen. I tried correcting this by restoring default settings via ITunes. The Restore Failed with error 1602 and now the IPOD touch is completely dead. It will not power on or respond when I plug it into my PC via USB

My IPOD Touch initially had a white screen. I tried correcting this by restoring default settings via ITunes. The Restore Failed with error 1602 and now the IPOD touch is completely dead. It will not power on or respond when I plug it into my PC via USB. I get an error on my PC stating that device attached to USB port is not recognizable. Can anyone help?

Error 1602: Try the following steps to resolve this error:
Ensure proper USB isolation troubleshooting has been performed, and test with a known-good cable.
Follow the steps listed for Error 1604.
This error may be resolved by disabling, deactivating, or uninstalling third-party security, antivirus, and firewall software. See steps in this article for details on troubleshooting security software.
Above from:
http://support.apple.com/kb/TS3694

HT4061 I cannot switch my IPAD on and it will not power up - i had this problem before and cannot remember how we fixed it?

Can anyone help us please?
I cannot switch my IPAD on and it will not power up - i had this problem before and cannot remember how we fixed it?

Press and hold both the home button and lock button until the apple logo shows up.

My HP Pavilion dv9700 will not power up. Lights blink on and off on a cycle, but screen is black

My HP Pavilion dv9700 will not power up. Lights blink on and off on a cycle, but screen is black.

Please post your Full Product Number
http://h10025.www1.hp.com/ewfrf/wc/findModel?lc=en&dlc=en&cc=us

External hard drive will not power on

I have a PH3200U-1E3S and it will not power up, every other push of the power button the light flashes once. I dont know what to do, any suggestions? The unit is not very old and it has all off our pictures on it.
please help,
Thanks Tony

If it is out of warranty, you might try opening it up and looking for a fuse inside. If you find one and it is blown, you should easily be able to find a replacement.

2nd Gen Time Capsule - will not power up - just stopped working all of a sudden - I have tried other power outlets - I have tried pressing the reset button - no light

2nd Gen Time Capsule - will not power up - just stopped working all of a sudden - I have tried other power outlets - I have tried pressing the reset button - no light

The power supply is shot. But that it lasted even this long is the wonder.. not that it died.
The TC runs too hot..
Look on ebay for "Time Capsule power supply"
You can get a replacement and fix it although the economics are not so good.. it is probably time for a new TC.
If you can DIY it is really only a few dollars worth of capacitors that go bad.
See https://sites.google.com/site/lapastenague/a-deconstruction-of-routers-and-modem s/apple-time-capsule-repair
For a bunch of alternatives.

My HP Pavillion A6700y will not power on after power surge

Similar Messages

Maybe you are looking for