My solution for AEBS locking up (NTP server not reachable)

I'll prefix this by saying that the issue that I found is pretty rare, but easy to fix.
I had a problem with my Airport Express that would cause all sorts of weird problems. After a couple days, either it wouldn't print, not allow clients to associate, not accept the correct password in the Airport Admin Utility, or not show up in the Airport Admin utility.
It turns out that I had enabled using a NTP server, but the NTP server wasn't reachable. In my network setup, the airports are in part of the subnet that's firewalled from the internet. The fix was for me to change the NTP server to an internal machine, but turning off NTP would have worked just the same.
NTP seems to only be used for logging, so turning it off shouldn't affect network performance.
I haven't had to reset either base stations since.

Here you go!
Use the terminal and be a root user and follow the steps bellow:
cd /etc
more ntp.conf
Then include this two lines:
server 127.127.1.1 prefer
fudge 127.127.1.1 stratum 3 refid NIST
After that save and exit. Then checked your ntp using the server admin tool and thats done. Be warn don't mend anything with the system preferences date and time.

Similar Messages

I have put Netflix on my Macbook Pro but Silverlight will not run. I receive a black screen that says "player error." Does anyone have a solution for this. Netflix support is not so hot.

I have put Netflix on my Macbook Pro but Silverlight will not run.I receive a black screen that says "player error." Does anyone have a solution for this. Netflix support is not so hot.I can use Netflix straming thru my Blueray on my TV but it will not run on my Pro. Thanks

Try running Safari in 32 bit mode. In get info box for Safari,
check open in 32 bit mode. There have been some oddities
on some systems that can cause some issues.
I had thought MS had fixed this, but may not have.

SPA 3102- STUN SERVER NOT REACHABLE

Hello,
Following are Line 1 settings of an SPA-3102
Nat mapping enabled=yes
Nat keep alive enabled=yes
Proxy server:correct proxy server specified
Outbound proxy server: Correct outbound proxy server specified
UserID and passwords are configured properly
SIP TAB:
RTP port min=16384
RTP port max=16390
Handle via received=yes
Insert via received=yes
Substitute via addr=yes
STUN enable=yes
STUN Server=aa.aa.com (correct STUN server configured)
Hadle via rport=yes
Inser via rport=yes
Send resp to SRC port=yes
STUN test enable=yes
TURN server=not configured
STUN test enable=yes
EXT IP=not configured
NAT keep alive INTVL=15
Problem:
On the REGISTER message I am receiving following warning
Warning: 399 spa "STUN Server Not Reachable"
User-Agent: Linksys/SPA3102-5.1.7(GW)
Content-Length: 0
Allow: ACK, BYE, CANCEL, INFO, INVITE, NOTIFY, OPTIONS, REFER
Supported: x-sipura, replaces
Would you please explain why I receive STUN not reachable warning? It is a reachable STUN server. SPA 3102 devices are placed behind ADSL modems of ITSP

I just noticed that you have Handle VIA received = yes, so if the proxy is responding with a 'received' tag, then the SPA would learn its external IP, without needing to contact the STUN server. I have a system that is behind NAT but does not need STUN or symmetric RTP, because it uses the IP from the received tag in the SDP. (In my case, I have the RTP ports forwarded to the SPA, so no port number translations are needed.)

Need solution for opening multiple connection to server in parallel

Hi..
I have used URL and URLConnectin classes to open connection to server,
and i used URLConnection.getInputStream( ) to download HTML pages.
Now my requirement is to open more than one connecton to single HTML document and download the file in parallel.
for example, if the HTML file size is 60KB..then i open three connection and
connection 1 downloads first 20KB
connection 2 downloads second 20KB
connection 3 downloads final 20KB
all the above should be done in parallel....by threading or else..
first of all i want to know is it possible to do the above in java?
anybody having solution for the above requirement?
venu

hi,
i too have the same problem
actually i am designing a download manager ,and had the same problem
that how to put multiple threads for doing it ,,,,
have u got solution for it..
if so please help me..
my mail id is [email protected]
i want help in designing the download manager
can any one help me out plzzzzzzzzzzzzzz
bye

I have a solution for DKIM signing in Windows Server

Hello.
I have a solution for DKIM signing Keys in Windows Server 2008 and 2012
Explanation will be long in the forum.
If someone in need, please contact me by skype ID: sasgroupe
Thank you

Hi,
Nice.
But is it feature that header is not scroll horizontally ?
Br, Jari

Solution for Syncing on Outlook Exchange Server

At my workplace we have Outlook 2003 running on an Exchange Server. Here are the symptoms I was getting:
1. Calendar events would sync from iPhone to Outlook, but not from Outlook to iPhone.
2. Sync process would be interrupted by an ApplieMobileSync.exe "exception unknown software exception (0xc00000fd) occurred at ... ". Watching in Task Manager, I noted that this happened whenever the memory usage for that program hit about 150MB.
I tried many of the currently-posted solutions, such as removing recurring appointments, creating a new calendar, downrevving iTunes, etc. to no avail.
HERE IS WHAT WORKED: SET THE "APPLE MOBILE DEVICE" SERVICE TO RUN WITH YOUR NETWORK CREDENTIALS INSTEAD OF USING LOCAL SYSTEM ACCOUNT. This is becuase on an Exchange Server, the calendar really lives on the network server, not on your local machine.
HOW-TO:
1. Go into Computer Management (in XP, right-click on My Computer, select Manage, open Services and Applications, and choose Services.
2. In the list of services, right-click on the Apple Mobile Device service and select Properties. In the Log On tab, select the radio button for "This Account" and enter your network credentials, with your full account name (ex. domain\username) and password.
3. Restart the service and iTunes. Then try syncing.
I realize this is pretty technical for some users and in some companies you might not even have the right to edit services on your PC. Plus, any time your network requires you to change passwords, you'll have to go into this service an update your credentials. Given these caveats, I consider this more of a WORK-AROUND than a complete SOLUTION, and believe Apple should come up with a way to automatically set up this service in Exchange environments.

Hello, looks like it's not available on the Mac, not sure because I don't have it...
http://answers.microsoft.com/en-us/mac/forum/macoffice2008-macstart/how-do-you-a dd-voting-buttons-on-outlook-for-mac/bda04f62-199e-4d42-9af9-8f2f972bf1a8?msgId= 8ad56ce9-5d92-4ee9-bafc-47eb22518ab1
If it were, then this would be the way...
http://www.ehow.com/how_6012653_add-buttons-message-microsoft-outlook.html

Afaria Trial Server Not reachable

Hi All,
I created a SAP Afaria Trial account, the account has instantiated a Server with a IP private address
which is not reachable, I have tested the IP (10.17.3.207) with following tools
Ping.eu
Tracert
It fails to reach the server
I did the following :
Went to the site http://www.sapmobilesecure.com/
Clicked on Free Trail
Registered my self
Got Two emails with login credentials
Logged into the server https://portal.sapafaria.com/login.php
Got the Server IP(10.17.3.207) address from Server Tab from the Administrator menu
Tried to access the wsdl as follows from desktop chrome browser
http://10.17.3.207:7980/AfariaService/Policy?wsdl
Which returns following error message in the chrome browser (I have installed fiddler in chrome)
[Fiddler] The connection to '10.17.3.207' failed.
Error: TimedOut (0x274c).
System.Net.Sockets.SocketException A connection attempt failed because the connected party did not properly
respond after a period of time, or established connection failed because connected host has failed to respond
The IP provided is private(as tested from ping.eu).
Can any one help in any pointer to resolve the issue.

Hello Prakash,
as SAP Afaria is a tool for mobile devices, you might have a faster answer if you post this question in the SAP for Mobile Discussions (as that Space is more relevant for mobile-related problems).
Regards,
Laszlo

IDES 4.7, MMC - disp+work running but message server not reachable

Hi,
I loaded IDES 4.7 in Windows 2003 server with Oracle 9i. While starting MMC, the disp+work running but message server not reached causing the issue.
Please suggest,
Thanks,
Prasad

Hi,
Please find the logs from the file Dev_disp
rdisp/http_min_wait_dia_wp : 1 -> 1
Fri Jul 13 14:14:52 2007
***LOG Q0I=> NiPConnect2: SiPeekPendConn (10061: WSAECONNREFUSED: Connection refused) [nixxi.cpp 8588]
ERROR => MsIAttachEx: NiBufConnect to plvprasad/sapmsDEV failed (rc=NIECONN_REFUSED) [msxxi.c      633]
***LOG Q0L=> DpLoopInit, nomscon () [dpxxdisp.c   1545]
Fri Jul 13 14:14:54 2007
CCMS: start to initalize 3.X shared alert area (first segment).
Fri Jul 13 14:15:31 2007
ERROR => MsISnd2: not_attached [msxxi.c      1296]
***LOG Q0N=> DpRqNoWpHandle, MsSndName () [dpxxdisp.c   4049]
ERROR => MsISnd2: not_attached [msxxi.c      1296]
***LOG Q0N=> DpRqNoWpHandle, MsSndAdmin () [dpxxdisp.c   4130]
Fri Jul 13 14:15:33 2007
***LOG Q0I=> NiPConnect2: SiPeekPendConn (10061: WSAECONNREFUSED: Connection refused) [nixxi.cpp 8588]
ERROR => MsIAttachEx: NiBufConnect to plvprasad/sapmsDEV failed (rc=NIECONN_REFUSED) [msxxi.c      633]
Fri Jul 13 14:15:36 2007
ERROR => MsISnd2: not_attached [msxxi.c      1296]
***LOG Q0N=> DpRqNoWpHandle, MsSndName () [dpxxdisp.c   4049]
Fri Jul 13 14:15:38 2007
ERROR => MsISnd2: not_attached [msxxi.c      1296]
***LOG Q0N=> DpRqNoWpHandle, MsSndName () [dpxxdisp.c   4049]
Fri Jul 13 14:15:42 2007
ERROR => MsISnd2: not_attached [msxxi.c      1296]
***LOG Q0N=> DpRqNoWpHandle, MsSndName () [dpxxdisp.c   4049]
ERROR => MsISnd2: not_attached [msxxi.c      1296]
***LOG Q0N=> DpRqNoWpHandle, MsSndName () [dpxxdisp.c   4049]
ERROR => MsISnd2: not_attached [msxxi.c      1296]
***LOG Q0N=> DpRqNoWpHandle, MsSndAdmin () [dpxxdisp.c   4130]
ERROR => MsISnd2: not_attached [msxxi.c      1296]
***LOG Q0N=> DpRqNoWpHandle, MsSndAdmin () [dpxxdisp.c   4130]
Fri Jul 13 14:15:43 2007
ERROR => MsISnd2: not_attached [msxxi.c      1296]
***LOG Q0N=> DpRqNoWpHandle, MsSndName () [dpxxdisp.c   4049]
Fri Jul 13 14:15:53 2007
ERROR => MsIAttachEx: NiBufConnect to plvprasad/sapmsDEV failed (rc=NIECONN_REFUSED) [msxxi.c      633]
Fri Jul 13 14:16:13 2007
ERROR => MsIAttachEx: NiBufConnect to plvprasad/sapmsDEV failed (rc=NIECONN_REFUSED) [msxxi.c      633]
Fri Jul 13 14:16:33 2007
ERROR => MsIAttachEx: NiBufConnect to plvprasad/sapmsDEV failed (rc=NIECONN_REFUSED) [msxxi.c      633]
Fri Jul 13 14:16:54 2007
ERROR => MsIAttachEx: NiBufConnect to plvprasad/sapmsDEV failed (rc=NIECONN_REFUSED) [msxxi.c      633]
Fri Jul 13 14:17:14 2007
ERROR => MsIAttachEx: NiBufConnect to plvprasad/sapmsDEV failed (rc=NIECONN_REFUSED) [msxxi.c      633]
Fri Jul 13 14:17:35 2007
ERROR => MsIAttachEx: NiBufConnect to plvprasad/sapmsDEV failed (rc=NIECONN_REFUSED) [msxxi.c      633]
Fri Jul 13 14:17:56 2007
ERROR => MsIAttachEx: NiBufConnect to plvprasad/sapmsDEV failed (rc=NIECONN_REFUSED) [msxxi.c      633]
Fri Jul 13 14:18:16 2007
ERROR => MsIAttachEx: NiBufConnect to plvprasad/sapmsDEV failed (rc=NIECONN_REFUSED) [msxxi.c      633]

Air video server not reachable?

I cannot figure out why the air video server is not reachable.

Also, see here:
http://www.inmethod.com/air-video/troubleshooting.html

Frame 9 solution for table column + side head does not work in Frame 10 and 11

In Frame 9 structured (DITA) we could force Frame to record the actual widths of table columns in the DITA XML. Frame 9 would respect the widths when opening the file. This was particularly useful for forcing tables to be wide -- to go across the column and the side head -- and for the columns to never resize.
In Frame 9 this was done by commenting out the line
"writer use proportional widths;"
like this
"/* writer use proportional widths; */"
in the topic.rules.text" file located in
"...\FrameMaker9\Structure\xml\DITA\app\DITA-Topic-FM"
This no longer works in Frame10 and Frame 11. Even though the same line is commented out in all the "NAME.rules.txt" files in all the subdirectories of
    "...\AdobeFrameMaker11\Structure\xml\DITA_1.2\app"
and
    "...\AdobeFrameMaker11\Structure\xml\DITA\app"
and
    "...\AdobeFrameMaker10\Structure\xml\DITA_1.2\app"
and
    "...\AdobeFrameMaker10\Structure\xml\DITA\app" .
Commenting out the line does force Frame 10 and 11 to record the absolute column width (2.357" etc.) in the DITA XML.
However, on Open, Frame 10 and 11 force the table to fit in the column, not the column and sidehead. That is they behave as though they were still using proportional column widths. It seems the original values (as inserted by Frame 10 and 11 before closing!) are recalculated on Open, thereby mimicking the default proportional width behavior.
For example, this on Save then Close from Frame 10 or 11
<table frame = "topbot" colsep = "0" rowsep = "1">
<tgroup cols = "4" colsep = "0" rowsep = "1" outputclass = "FormatB">
<colspec colnum = "1" colname = "1" colwidth = "1.796in" colsep = "0"/>
<colspec colnum = "2" colname = "2" colwidth = "1.852in" colsep = "0"/>
<colspec colnum = "3" colname = "3" colwidth = "1.179in" colsep = "0"/>
<colspec colnum = "4" colname = "4" colwidth = "2.152in" colsep = "0"/>
goes to this on Open then Save:
<table frame = "topbot" colsep = "0" rowsep = "1">
<tgroup cols = "4" colsep = "0" rowsep = "1" outputclass = "FormatB">
<colspec colnum = "1" colname = "1" colwidth = "1.351in" colsep = "0"/>
<colspec colnum = "2" colname = "2" colwidth = "1.393in" colsep = "0"/>
<colspec colnum = "3" colname = "3" colwidth = "0.887in" colsep = "0"/>
<colspec colnum = "4" colname = "4" colwidth = "1.618in" colsep = "0"/>
Any help at all would be appreciated!
We have 8,000 to 10,000 pages to PDF in the next few days and about 33% of those pages are messed up tables!
Message was edited by: borealforest

Hi...
Unfortunately, I don't have any insight into the default DITA table handling in FM10 or FM11 .. so can't give you the answer you're looking for. Since both FM10 and FM11 offer ExtendScript, you could write a script (or have one written) that processes all of your files to reset the table widths. Or, perhaps the best short term solution may be to reinstall FM9 to get the job done, then spend more time later to figure out a better solution.
One alternative would be for you to use DITA-FMx, which supports the table/@pgwide attribute for controlling which tables span the page and which don't. Since your tables probably don't make use of this attribute, it won't help in the near term, but might make sense going forward.
Cheers,
Scott Prentice
Leximation, Inc.
www.leximation.com

Solution for using HDMI output to devices not supporting HDCP

I read a number of similar posts about this issue and wanted to share my experience on it, propose a possible solution and ask if anyone else has already tried it.
Symptom
The symptom is that when playing rented content (some have reported this with purchased content as well, but that's not my experience) *you hear audio, but see either a black or a white screen with no video*.
_My Experience_
I had this problem with my Boxlight Cinema 17SF projector, which is a few years old. It has a DVI input, so seeking to get the best picture possible, rather than connecting the Apple TV to the projector using a component video cable, I tried to use an HDMI to DVI cable. It looked great for TV shows and purchased movies, but when trying to view movie rentals I was hearing audio, but seeing only a black screen. I called Apple support, told them about the problem and gave them my exact configuration, but they didn't have any suggestions to offer beyond restoring to factory defaults and upgrading. I tried this, and tried every possible video resolution and projector setting, but after days spent on it, nothing would solve the problem.
_Background on the Problem_
After reading some posts from helpful users in the Apple TV forum, and after some googling, I found that this problem happens when users try to use an HDMI to DVI cable to connect the Apple TV to an older display device, such as a high definition TV or projector. As it turns out, content played over the HDMI connector is protected using HDCP (http://en.wikipedia.org/wiki/HDCP, http://www.projectorpeople.com/cables/HDCP_DVI.asp).
Essentially, in order to properly display content, the display device needs an HDCP chipset from a subsidiary of Intel, which older devices do not have (plus for HDMI, HDCP support is mandatory but for DVI, it's optional). If your display device does not have this chipset, or worse yet, if it has the chipset but it isn't compatible with the Apple TV version of the chipset, video content will not display and you'll typically get a black or white screen. Apple must have gotten a number of support calls on this, as I read in a recent post that they no longer support using HDMI to DVI cables to connect your Apple TV to your display device. Aha.
_Component Video_
One of the nice things about component video is that there's no HDCP to worry about. You can use the component video output on the Apple TV to connect to your display device, and you'll be able to view all content. In my case, I'm using a component video to SVGA adapter. It works, and I can view all content, purchased or rented.
Unfortunately, however, aside from component video being an analog rather than a digital signal, the component output on the Apple TV is crippled and only supports 480i resolution. So if you have a high definition device and want to use component video at higher resolutions than 480i to watch your high definition movies, you're out of luck.
Just as an aside, component video looks best for me when I go into the settings and first try to select 720p resolution. I hear two "beep beep" sounds (the same sound as when you try to navigate beyond the end of a menu) and briefly see a menu showing that the Apple TV is canceling the resolution change for me (holy cow that's weak, they crippled this at the interface level), and the Apple TV forces me back to 480i. However, for some reason the contrast is better after this, colors are better and blacks are much deeper. Despite this unexplained oddity which may only be true for my Cinema 17SF DLP projector, the resolution is still limited to 480i.
_Possible Solution?_
After some more googling, I ran into this device called an HDFury at http://www.hdfury.com/. Apparently, it's an HDMI to VGA/component video converter that strips HDCP from the video and allows the use of resolutions up to 1080p. There are two versions, the HD Fury and the HD Fury 2. Although it's pricey, I'm going to give the HD Fury 2 a try. Even though it wouldn't be a digital connection to my projector, at least it should allow me to use 720p or 1080p, in theory.
I should point out that I'm not sure about the legality of this device. Essentially you're removing something that was supposed to be there to prevent people from copying digital content, but regarding this I think a couple of things: 1) It's only an analog output (SVGA or component), so you're not getting the original digital data and 2) you're using this for personal use, or you should be. You're not using it to circumvent the DRM, but only so that you can view the content you've rightfully purchased or rented.
So, *has anyone tried this device with the Apple TV*, or discovered another way to get all available resolutions when displaying on older high-definition devices using DVI or component video? I'll wait a few days for responses, then go ahead and buy one and post again about my results with it. Thanks for any advice.

I have an update on this that should clarify one critical thing and make my original premise about the use of an HD Fury unnecessary (although the content of the post might still be useful). I had thought that the component video output on the Apple TV was crippled to 480i, but it's not.
What was happening to me was that 720p and 1080i resolutions were taking a long time to sync on my projector, so I was never seeing the Cancel/OK menu that comes up to accept the resolution. I thought that the Apple TV was selecting Cancel for me, but it wasn't, it was just timing out because I never accepted the new resolution.
So, if you KNOW that your device supports the resolution you're selecting (such as 720p) and your device is just taking a long time to sync, select the new resolution, wait a second then press down and OK on your remote, even though you don't see anything. You'll accept the new resolution.
However, *if you do this and the new resolution doesn't work, you could be hosed*. I suggest that if this is the case, remember the remote keypresses necessary to back out and reverse the change. For example, remember the number of times you need to press up or down to return to your original resolution, then hit OK, down then OK to go back to a safe resolution, like 480i.
At least now, I'm able to use 720p or 1080i with the component video output, and it works with both rented and purchased videos. It still doesn't work with the HDMI -> DVI cable, but the use of the HD Fury should be unnecessary when the Apple TV component output supports all resolutions.

Best Solutions For Offline Address Book on Workstations Not Updating Frequently Enough?

We use Exchange 2010 SP2 and we set Outlook 2010 to Exchange Cached mode by default for all workstations. This seems to work OK for the majority of email most of the time, but because we are very frequently adding and removing external mail contacts
and and adding and removing them from distribution lists, the GAL and distribution lists memberships are frequently out of date in the middle of the work day.
Sometimes the users can manually download an updated OAB assuming it has been updated on the server, but sometimes the OAB is not updated yet and redownloading the OAB solves nothing. It is a lot of hassle, confusion about bounced messages and
missing contacts and phantom names in distribution lists with this method.
I notice that for mail contacts, there is an All Contacts address book that is live, but it does not include include anything else other than contact addresses. Distribution List memberships are still out of date until the OAB is updated on the server
and then downloaded to the Outlook client. This is taking too long.
Is there a keyboard shortcut to force the client to do a GAL address lookup in online mode rather than using the cached OAB?
Can Outlook display both an online and offline address book for the GAL and let the user manually select online version of the GAL if a contact or new mailbox or DL has not synced to the OAB yet?
If we set the registry key to force online address books even when Outlook is in cached Exchange mode, is there any performance downside for PCs on the LAN other than the GAL being unavailable when the network is not available?
Would the Exchange server have a significantly higher load if most PCs were accessing the GAL without an OAB cache?
If we should not expect a significant increase in server load or network traffic, we might set desktops to use online access to the GAL and only laptops to use OAB.

Hi,
If users are accessing the GAL without OAB cache, definitely it will increase in server load and network traffic. If you are in cached mode, one suggestion is to define that in Send/Receive Settings:
Go to Send/Receive Groups -> Define Send/Receive Groups
-> Select the account and Edit -> Select
Include the selected account in this group, and check Download offline address book -> Click
OK -> Go back to Send/Receive Groups, select the frequency for automatic send/receive(Schedule an automatic send/receive every x minutes.), and then close.
I hope this setting can help in your scenario.
Regards,
Melon Chen
TechNet Community Support

I cannot get rid of the AOL tool bar. I use FF 14.0.1. Posted solutions for old versions of FF do not work.

This is a problem that occurs on my wife's computer, not this one. The only difference on that computer is that has a D-Link USB adapter as it is connected to our network via a wireless router. Could that have something to do with the problem? Could the installation of the D-Link program have brought along the AOL tool bar with it?

See also these to check for locations of installed third-party extensions:
*https://developer.mozilla.org/en/Installing_extensions
*https://developer.mozilla.org/en/Adding_Extensions_using_the_Windows_Registry

WebSphere jars required for JNDI connection factory (App server, not file)

I need to configure an initial context to a JNDI-defined WebSphere Topic Connection Factory. I believe the class needed is "com.ibm.websphere.naming.WsnInitialContextFactory", but I cannot determine the specific jars required to successfully execute the connection.
Any help at all would be deeply appreciated.

I have the same question. Who knows answer please reply

HADR Solution for SQL Server Analysis Services (SSAS) 2014 on Azure Iaas

Hi All
I am required to build a HA/DR solution for SQL Server and SSAS 2014 on Azure. So far I could build AlwaysOn high availability solution for SQL Server on Azure but haven't found any solution for SSAS.
Failover Clustering is not an option on azure because of the restriction of not been able to use shared storage. We also determined that the cost savings of using SQL + the cost of the 3rd Party replication tool was a wash (ie no real cost savings).
Any lead on this would be appreciated.
Thanks,
Viral Shah
Thanks - Viral

Hi Viral,
A clustered implementation of SSAS can be configured in Microsoft Azure. Such a configuration would need to meet all the requirements stated in the following document including Active Directory and storage.
How to Cluster SQL Server Analysis Services
http://download.microsoft.com/download/D/2/0/D20E1C5F-72EA-4505-9F26-FEF9550EFD44/SSAS_Failover_Cluster_V4.docx
Thanks,
Lydia Zhang

My solution for AEBS locking up (NTP server not reachable)

Similar Messages

Maybe you are looking for