No sound following iTrip connection

So I recently connected my Griffin iTrip device (model P1591) up to my new iPhone 4 so I could play my music through the stereo in my Jeep. It occasionally would play and appeared to not work correctly with the new iPhone. After determining it wasn't going to be compatible with the new phone due to lack of functionality, I disconnected and went about my merry way. However I now keep getting a pop up randomly that reads "This accessory is not optimized for this iPhone" and continuously pops up with no particular reason or trend. I've tried reconnecting the iTrip, deleting the iTrip software, etc all to no fix of this issue. The biggest problem however is that it apparently has triggered something on the phone to make it believe that the iTrip is constantly connected, causing there to be no sound what so ever through the "external speaker" or speaker phone speaker of the phone. I've only been able to get ring tones to play through it, and when headphones are plugged in, everything appears normal. The volume controls of the iPod are completely gone, however I can play a song. Any suggestions or known fixes for this? I'm attempting a restore of the phone now to see if that fixes it.

Have tried multiple restores from both my old iPhone, and as a new iPhone, and still have the message popping up. I've even tried uninstalling all software that doesn't normally come with the phone. Suggestions?

Similar Messages

  • Rapid alarm sounds followed by rapid whooshing sounds

    I have a macbook air and within the last few months when I am on the internet, I hear rapid dinging alarm like sounds followed by rapid whooshing sounds as if hundreds of emails are sending when I have no emails to send.  Has this happened to anyone else?  Has my computer been hacked?  I am on my second new credit card due to someone hacking my credit card but was luckily caughter by Barckley Credit Card.  Maybe I am connecting two separate issues.

    Doubtful it's a security issue ...
    Check System Preferences > Sound > Sound Effects
    Deselect:  Play user interface sound effects

  • IPhone Pulse sound when headphones connected

    When I connect my Samsung headphones to my iPhones 4s I hear a pulsing type sound and when I play music or get on FaceTime the sounds goes in and out in the rhythm of the pulse. Does anyone know what this may be?

    That is odd, however this is pointing to more of a software issue so I would advise trying a firmware repair:
    Please note that performing these steps will delete all user data except for your media files (photos, music and video).
    If your handset is able to be powered on and unlocked you can follow the below steps to back-up your personal data prior to running the repair.
    Backing up your handset
    To back up your phone using PC Companion 
    1. Go to Support  to install PC Companion on a Windows computer. 
    2. When installed, start PC Companion on the computer. 
    3. Connect your phone to the computer using a USB cable. 
    4. Click Start under Backup & Restore. 
    5. Follow the on-screen instructions.
    Exactly what contents will be backed up may differ depending on phone model.
    You can view detailed information about this as you follow the steps in the Backup & Restore wizard.
    Running the software repair
    Before you start you have to download the PC Companion software and install it on your PC.
    Once installed on your PC, double-click the PC Companion icon on your desktop to start the update.
    Please ensure your phone is powered off and not connected to the PC when you begin this process. You are not required to connect the phone until after step 10.
    1. Install and open PC Companion then select Support Zone.
    2. Phone Software Update.
    3. Start.
    4. Repair Phone
    5. Continue
    6. Accept data removal
    7. Next
    8. Wait for prepare
    9. Select Phone
    10. Follow the connection steps
     - Official Sony Xperia Support Staff
    If you're new to our forums make sure that you have read our Discussion guidelines.
    If you want to get in touch with the local support team for your country please visit our contact page.

  • No sound when I connect my Macbook pro (2012) to TV via HDMI!

    Hi! I have a problem with the sound when I connect my Macbook pro (bought in 2012) to a Phillips HD TV. The strange thing is that it only happens with some videos (specially youtube videos) but the sound works perfectly with films and audio files I have in my computer, and also when I watch TV online (Eurosport player for instance and other similar applications). It's even stranger because it doesn't happen all the time; last week I tried many times to watch some youtube videos and after unplugging the HDMI cable it seemed to work. As I said, with Eurosport player and many films downloaded in my macbook I don't have this problem (sound is ok all the time), and this is why I'm really confused. I suppose it's not a connection problem, otherwise I wouldn't have sound in any video, right? I've tried two different HDMI's cables but nothing has changed. Please, someone help me, as I can't figure out what's happening. Thank you very much!

    Well Im not sure what the fix is for your problem, but can you please open up the sound preference next time you connect the philips tv, and make sure that sound output is set to hdmi out. Then try and play your video's etc and see if they are affected. 
    I can tell you I get a similar problem when, for example, I have a youtube window open and then connect the external display. The youtube video will not sound out through the cable, however if i refresh the window it works. Also the same when I use bluray player on mac, I have to close it and open it again for the sound to output through the external monitor.

  • My iphone 4 does not appear in my(windows 7) lap top, when i connect i can hear the sound of usb connected, but its not appear in the itunes or computer, and its not charging as well, bit confusing

    my iphone 4 does not appear in my(windows 7) lap top, when i connect i can hear the sound of usb connected, but its not appear in the itunes or computer, and its not charging when i connected to the laptop as well, bit confusing, help please

    Take a look at this link, http://support.apple.com/kb/TS1538

  • There's no sound when i connect to apple tv

    Hi,
    There's no sound when i connect to apple tv from my macbook pro, i bought it 10 days ago and it got the newest updates, and the volume is turned on on the computer.  The sound works when i connect ipad and iphone but not the macbook pro with retina. Does anyone know how to get the sound to work?

    Hi,
    Have you tried Option click on the sound icon in the status bar at top right of your screen? It shows the Output and Input options. Select your Apple TV there.

  • TS1470 Since very recently whenever I connect to Whatsapp and a few other Apps I get the following message  " CONNECT TO I TUNES TO USE PUSH NOTIFICATIONS"   After connecting to I Tunes I am unable to find any solution there

    Since recently whenever whenever I check any application especially WhatsApp, before it opens I get the following notification:
    : CONNECT TO I TUNES TO USE PUSH NOTIFICATIONS: After connecting to I Tunes I find no solution there?

    Dropbox is virtually disabled on my phone now because of these messages, and most other apps are now difficult to use. I have rebooted the phone several times, reset network settings and restored factory settings (and had to make all my adjustments again) but nothing worked. My phone is now almost totally useless.

  • Why am I getting sound distortion when connecting iPad 2 to amplifier.

    I am getting sound distortion when connecting iPad or iPod thru amplifier using AirPlay or 3.5mm to rca cables. Also the sound has far too much bass. No problems when connected in car.

    It sounds like a mismatched impedence.  What are you connecting to?   the output from the jack is intended for headphones, and is not just an audio out.
    Try turning the volume on the pad way down, and use the gain on your amp, and see if that minimizes the issue.
    There is a pure audio signal for both channels on the 31 pin plug, but you would need a special cable to use it.  I would bet they are available if you google.  Although I have read that the 31 pin signal is not filtered like the headphone output, so while it is a pure audio output, there may be some noise in it that would need to be filtered.
    Try google for a 31 pin cable.  ( the input for the car is probably built to take a signal from a headphone output, while your amp may be expecting a lower power signal)

  • Sound when I connect the Ac

    I wounder if there is anyway to get rid of the annoying sound everytime I connect/disconnect the AC?

    You may be able to turn it off in BIOS. Unfortunately as I don't have a 3000 notebook I can't tell you where. On thinkPads it is found in the BIOS > Config > Alarm menu, Power Control Beep.
    Hopefully this helps.
    Andy  ______________________________________
    Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
    Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
      Deutsche Community     Comunidad en Español    English Community Русскоязычное Сообщество
    PepperonI blog 

  • I'm having problems backing up my iphone 4 to icloud since 13/04/2012. First it says it's going to take about 5 hours, then it says backup failed. Following instructions-connected to wi-fi, plugged into PC

    I'm having problems backing up my iphone 4 to icloud since 13/04/2012. First it says it's going to take 6 hours, then it says backup failed. Following instructions-connected to wi-fi, plugged into PC & locked the phone (though never had any problems like this before), but still no difference. Any ideas/similar problems?

    unfortunately there are tons of people with this issue but Apple has not given any answers for us to fix this issue yet. I wish they would allocate more people to solving these problems when they roll out new versions of itunes along with new hardware.

  • My i mac is having trouble at Start up and often makes a clicking sound followed eventually by a folder icon on the screeen that shows a file with a questionmark inside,  Is this a sign that my hard drive is failing?

    My i mac is having trouble at Start up and often makes a clicking sound followed eventually by a folder icon on the screen that shows a file with a question mark inside,  Is this a sign that my hard drive is failing?

    As for the folder with a '?', here is some info that might help:
    https://discussions.apple.com/thread/5201710
    http://support.apple.com/kb/TS2570
    Hopefully you are making regular full backups just in case the hard drive is failing?

  • Hey i have an ipod touch 5gen ,it has stopped responding and is showing a blank black screen.when ever i connect it to itunes it gives a sound of the connection. what am i suppose to do?(ios7)

    hey i have an ipod touch 5gen ,it has stopped responding and is showing a blank black screen.when ever i connect it to itunes it gives a sound of the connection. what am i suppose to do?(ios7)

    Try:                           
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable
    - Try on another computer                            
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar                                     

  • Sometimes I hear a clicking or static sound followed by the inability of my caller to hear me, although I can hear them.  Often happens several times in a row.

    Sometimes I hear a clicking or static sound followed by the inability of my caller to hear me although I can hear them.  Sometimes happens several times in a row.

    NLEdit,
    Here's what I have (to the best of my knowledge):
    Original source: mini DV tape, it's all HD
    I use capture now to digitize the whole tape. My easy setup is: HDV- 1080i60 FiriWire Basic. After I have digitized all of it - it's an .mov file with the settings I just posted above. So when final cut is done digitizing I already have all the files in my browser window and I just drag them and drop them in the timeline and I choose to match the timeline settings if they're different. So my timeline settings look like this:
    Frame Size: 1440x1080
    Vid Rate: 29.97 fps
    Compressor: HDV 1080i60
    When I'm done editing, I use batch export to export a bunch of sequences (they all have the same settings I just mentioned above) and I chose:
    Format: QuickTime (custom), Compression Type H.264, frame rate: 29.97 fps, key frames: every 24frames, compressor quality- high, encoding: best quality. Then for size I choose either 1280x720 HD or I use "custom" to make them half the size of that so that would be 640x360. My point is to end up with an .mov file which I can then encode into an flv or just burn it on a data cd.
    As for your question number 1: I'm not even sure what you mean by that.
    Does all that make any sense now?

  • IPod touch. No sound through charging/ connection cable. What gives?

    I just fired up my iPod touch 64gb and connected it to my PC like usual.  No sound through the connecting cable.  Switched to a different cable; same problem.  Rebooted iPod; same problem.  Rebooted PC; same problem.
    Headphones work fine.  iPod speaker works fine.  Checked my setting on the iPod; didn't see an obvious problem.  What am I missing??
    Running iOS 5.0.1 through Win 7.
    Thanks for your help.

    The cable is the standard USB docking cable that is included with every iPT.  I have been using them for years and audio data is sent to the PC via this connection, just the same as if it was connected to an external docking device.  What is different is that is suddenly have no sound through this cable when I did before.  I have done a hard reboot of the iPT, connected it to a different PC, changed cables, etc.  Sound only comes through the heaphone port, not the docking port at the bottom of the iPT.

  • TS4006 how do I turn off the "make a sound" feature with find my mac.  I think my macbook was stolen and I don't actually want it to make a sound when someone connects.  I selected the feature and now I want to turn it off.  How can I do it?

    How do I turn off the "make a sound" feature with Find My Mac.  I think my macbook was stolen and I don't want it to make a sound when it connects.  Can turn the feature off somehow?

    ica310 wrote:
      I've read some forums that say I have to overwrite it with a silent sound file but I do not understand how to do this.
    You have to jailbreak your phone to do this, voiding all warranty & support. Just flip the Ring/Silent switch when you send.

Maybe you are looking for

  • Pop up text on clicking link on a sql report

    Hi I'm using apex 3.2 I've a sql report like below taskId(edit) Task_details Notes owner ..... What I want to do is if I click on taskId which is edit link ,pop up text box should open where I can add notes to that row. How can I achive this? Thanks

  • Getting 'File not found' error while using server object model code

    Hi, I am using server object model code to pull list data in a console application. My machine has standalone installation of SP 2010. I am getting error 'File Not Found', however the same operation is working fine with client object model code. Code

  • Originals naming in dms

    Hi all, I have an issue in SAP DMS, that when I upload the file, the name of file is not appearing and instead of that application name is coming. Is there any program in sap standard which can show the filename and not application name. Kindly help

  • Screen x,y control of a simple pop-up Confirm mini-window. Possible?

    Is it possible to control where on the screen an small confirm pop-up window will appear? I want not to appear in the middle but next to the right screen side. Do I need to build it and not use the default confirm window?

  • History in XI

    Hi all,                  I want to know how we can find the history of an object in IR and ID..is there is any way for this ..i am checking with history option in IR it is showing versions oif the objects..if i click on the old version is this versio