No Stock value at Storage location level in BW report

I am facing problem in getting stock valuation at storage location level.
  The problem is that, in R/3 Stock valuation is done at plant level, when we do storage location to storage location movement , only stock quantity gets changed and no FI entry is getting generated . So there is no movement of stock values at all. when we load this transaction data into BW , obviously i will arrive with wroung value . so what to do in this case ?
Thanks & Regds,
Kavan

Hi Kavan,
Could you please explain the scenario & provide the Ds you are using.
Thanks & Regards,
Suneel

Similar Messages

  • Need to display the Stock Values at storage location level - 0IC_C03

    Hi All,
    I am developing Stock Movent Report on 0IC_C03 - Material Stocks/Movements.
    I have more than one storage location for plant. Stock quantities are calculating at storage location level and Stock Values are calculating at plant level.
    I have no issues with quantities. Only problem with Values.
    2LIS_03_UM is not picking the starage location, so that the revaualtion values are falling under unassigned nodes. When i set filter on storage location these values were not showing as they are under un assigned nodes (#).
    I want to get the Stock Quantity and Stock Values at Storage location level in my report.
    I found that soulution for that is Applying SAP Note : How to Realize summarized display of stock values on storage
    I have done development as per the document. But when i run the Query it is going to debug mode first and then it saying This program cannot display the webpage
    Can any one faced the same situation, Please help me if so.
    Thanks in Advance.
    Gopal N

    Hi Sachein,
    I am getting this An exception(CX_RSR_PROPAGATE_X) occured when debugging, and then it leads to next screen saying that:
    This program cannot display the webpage
       Most likely causes:
    You are not connected to the Internet.
    The website is encountering problems.
    There might be a typing error in the address.
       What you can try:
         Check your Internet connection. Try visiting another website to make sure you are connected. 
         Retype the address. 
         Go back to the previous page.
         More information
    Please let me know you need any more information.
    Thanks in Advance
    Gopal N

  • How to realize summarized display of stock values on storage location level

    Hi all,
    we have implemented in Release 3.5 a report to analyze Stock values on storage location level according to the "How to...realize summarized display of stock values on storage location level"- paper. The report is running witout problems.
    Now we are going to upgrade our BW-system to release 7.01 in technical environment, we have not upgraded our reports.
    Executing the report in release 7.01 we get an error message "Object field I_S_DATA-0TOTALSTCK not found"
    The error is coming from line 14 Inc GET_FIELD_POSITION_D in Prog CL_EXM_IM_RSR_OLAP_BADI.
    Unfortunately the document "How to... realize summarized display of stock values on storage location level" can no longer be found in SDN.
    Is there any new How to - document for this kind of reporting?
    Does anybody can give me advice for chances in coding?
    Thank you for answers.
    Best regards,
    Andreas
    Edited by: Andreas Förner on Dec 9, 2009 1:52 PM
    I have got a solution from support.
    The solution is described in note 924320.
    Andreas

    Hi,
    I assume you have also created class "ZCL_IM_Z_MATERIAL_PRICE".
    In the implementation of virtual InfoObjects
    ZCL_IM_Z_MATERIAL_PRICE we have changed the method INITIALIZE:
    OLD:
    * fill the global variable
         UNASSIGN <l_global>.
         ASSIGN (l_global_name) TO <l_global>.
         CHECK <l_global> IS ASSIGNED.
         <l_global> = cl_exm_im_rsr_olap_badi=>get_field_position_d(
                                            i_fieldnm = <l_s_sfk>-kyfnm <--
                                            i_s_data  = i_s_data ).
       ENDLOOP.
    NEW:
    * fill the global variable
         UNASSIGN <l_global>.
         ASSIGN (l_global_name) TO <l_global>.
         CHECK <l_global> IS ASSIGNED.
         <l_global> = cl_exm_im_rsr_olap_badi=>get_field_position_d(
                                        i_fieldnm =
    <l_s_sfk>-VALUE_RETURNNM                                   
    i_s_data  = i_s_data ).
       ENDLOOP.
    This solved our issue.  Please regenerate the query after
    implementing the correction.
    Hope it solves you issue too.
    Best regards,

  • SIT Value and Stock value at storage location level

    HI
    Can anyone tell me how to get the following:
    1. The value of the Stock in Transit on monthly basis
    2. The value of the stock at storage location level. The Stock value is correct at      plant level
    Thanks in advance.
    Soumen

    Hello,
    (1) please have a look into the Howto Guide:
    https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/92c0aa90-0201-0010-17b1-bf5b11c71257
    (2) Please have a look into the note:
    589024
    And consider to use the feature Constant selection.
    http://help.sap.com/saphelp_nw04s/helpdata/en/d2/02223c5f00612be10000000a11402f/content.htm
    I hope this helps, Michael

  • Opening and closing balance values at storage location level

    Dear all,
    I want to know opening and closing balance values and receipts and issue values at storage location level for certain period.
    I tried with MB5B, it is not giving value at storage location level, it is giving quantities at storage location level and values at plant level. But requirement is: please see below example:
    All values are in USD          
    Storage location:      1001     1002
    Opening Balance:      2000     3000
    Receipts:                           1000      2000
    Issues:                            2000     3000
    Closing Balance:      1000     2000
    Please help in this regard (I want value of the stock only, not qty)
    Regads,
    Veerappa
    Edited by: Chinna Veerappa on Jul 27, 2010 5:27 PM
    Edited by: Chinna Veerappa on Jul 27, 2010 5:28 PM

    vlauation is at plant level (MBEW table) the storage location level does not carry values (table MARD).
    You may have to develope your own ZMB5B  program and calculate yourself what is not stored in SAP.

  • Report on QI, Blocked, Returned Stocks at Plant & Storage location level

    Hi,
    Would like to know any reports which gives QI, Blocked, Returned stocks at Plant & Storage location level.
    Regards,
    Vengat

    hi,
    What do you exactly mean say by "Returned  stock"..
    Also go through by MMBE tcode ...
    Regards
    Priyanka.P

  • WRONG STOCK DISPLAY AT STORAGE LOCATION LEVEL

    Hello to All,
           I've made stock transfer within plant using Mvt. 311, & now when I'm disaplaying storage loc. data in MMBE, MM03 & MC.5, it is showing negative stock for storage location from which it is transferred along with stock value as negative.
       As per IMG settings, negative stock is not allowed also not in the material master. Pls. guide me how to correct this stock, is it related to LIS updation, if yes then what is it's procedure.
    Thanks
    Amit

    If in MMBE, system is showing negative stock then negative stock has to be allowed for that plant, storage location & material.
    Pl check & confirm using following path.
    IMG -> Material Management -> Inventory Management & Physical Inventory -> Goods Issue / Transfer postings -? Allow negative stock.
    Regards
    Bhavesh Mistry

  • MCHB,MARD - Stock available at plant level and storage location level

    Hi ,
    How to determine how much stock available at Storage location level and Plant level. (Lot is not maintained).
    In MCHB-Stock at lot level is shown.
    In MARD-Stock at Storage Location level is shown lncluding
    the stock maintaned at the lot level.
    If i want to know the stock which is not maintained in Lot, i.e, Stocks directly maintained at Storage location / Plant.
    Do I need to subtract the MCHB Value from MARD Value ?
    Is there any other way available to find the stocks which is not maintained at lot level.
    Regards
    Prasath

    Hi prashant,
    What do u mean by stock maintained at SL level without batch level.  Do u mean that some materials are subjected to batch management and some or not?
    If that is the case, for all batch managed materials, u can see the stock at batch level and also same is summed up at SL level.  But still what ever u are getting from MARD table isstock at SL level only.
    If u have activated batch management for any material, it will always be shown at lot level also.
    hope this clarfifies query
    award points if found useful

  • Stock valuation down to Storage location level

    Dear all,
    System setup for stock valuation is till Plant level. And understand that's how data stored in table MBEW and MBEWH until plant level only.
    Eventhough that is system standrd, is that possible to get the stock valuation until Storage location level?
    For eg: In MB5B, there is opening stock, closing stock and the material movement posting. I need to get opening and closing stock for each storage location.
    Could you please comment if there are tables store these data? Kindly comment.

    Hi Afshad Irani,
    Thanks for your reply. Understand from the previous post that stock valuation for storage location can be done via table MARDH or report MC.9, but this tools are excess base on period/month basis.
    My case, i need to report storage location stock for both (1)last month 06.2010 and (2)yesterday's stock 06.07.2010. So i can use MARDH table to report (1)last month stock for each storage location. While for (2) yesterday stock, table MARDH isn't help.
    Could you please advice further?

  • Stock report in BW (valuated stock and Storage Location level)

    Dear All,
                Regards.We got an situation here,
    Case 1:  R3 (MB5B) (Both "Storage loc" and "Valuated stock" shows the same Stock Qty)
    1).The BW Stock Report shows values the Correct Values for "Receipt Qty" and "Issue Qty" with the Correct  "Quantity total Stock" aswell.
    Case 2 :   R3 (MB5B) (Stock is different between "Storage Loc" and "Valuated Stock")
    1).The BW Stock Report shows the  "Quantity Total Stock according to VALUATED STOCK Level(MB5B),but  the "Receipt Qty" and "Issue Qty" according to STORAGE LOCATION Level(MB5B) .
    We followed the "How to Handle Inventory "Doc with the proper sequence of Loading of Infosources and Compression.The data is sitting fine at the cube level.
    It would be great if someone can throw some Light on this issue,on how the Query shows a COMBO of both Valuated stock and Storage Location stock....Held up with this issue for quite sometime..Had a look at the   Oss Note (589024)...........
    Manythanks
    Arun

    HI,
    In Inventory we have two quantity fields given to satisfy the requirement.
    Valuated stock Qty - 0VALSTCKQTY
    Storage Location qty - 0TOTALSTCK
    You can make use of them based on your requirement. Hope this helps for you.
    Thanks,
    Arun

  • Valuated Stocks at Storage location Level

    Hi Gurus,
    Our client wants to develop a report on Quantity and Value of the Stocks at Storage location level. Is there any standard table/T.code where we can see this? We have tried in the Standard reports too.
    We have tried this getting from various tables like MARA,MARC,MARD,s031 & S032. But it is hitting the performance heavily. Please advice if anything can be done on this.
    with regards,
    Saakithyan

    Refer this link
    http://wiki.sdn.sap.com/wiki/display/ERPSCM/StockTablesandStockTypes
    check reports: MC.9 ,S_p00_07000139 also if it fits

  • Opening and closing stock at storage location level

    Dear all
    I need a std report which will give the opening and closing stock at storage location level, Or should I go for dev. if yes please guide me.
    Regards
    Samuel

    Hi,
    check if you can use S_P00_07000139 report, select "Display stock movement by plant (with amount) and further select Sloc from layout.
    Regards,
    Vikas

  • Opening and closing Stock report at Storage location level- date wise

    Dear all
    Is there any standard report to view opening and closing stock at storage location level? ( we have MB5B which resets the entry screen if we enter SLOC details).
    Thanks
    Sam

    Do  I have the option of  selecting Storage Location wise opening and closing stock on a particular date or period, that is what I have requested? Is it possible, evenafter selecting storageloc/batch stock and entering all the SLOCs in the selection creen, the report output does not contain any SLOC, and using ctrl+F8 or display variant does not have SLOC as a field also.
    pls gudie
    sam

  • Storage Location Level BW Stock Report

    Hi Experts,
    Does anybody know whether there is a BI Content report that shows storage location level stock information?
    Best Regards,
    FIRAT KAYIRAN

    Hi all,
    I know these queries based on infocube 0IC_C03. But these queries doesn't have a storage location detail. Anyway thanks for replies.

  • MC.9  drill down at storage location level

    In mc.9  report  stock against plant xxxx  at storage location drilldown
    I see
    In total  valuated stock is 0
    But
    at storage location 0040 I see  423.686 as valuated stock
    and at storage location 5M06 I see  minus 423.686  as valuated stock
    Client need to have not stock at plant level.
    In total I see 0
    But client is bothering about valuate stock he is getting at storage location level.
    Thanks,
    Kiran

    Hi Jurgen,
    For plant xxxx there is nil stock in mc.9 report. only I see sloc  to sloc transfer of qty. for example sloc 0001 has qty + 100 & sloc 0002 has qty -100.
    Finance is asking to user that this + - qty should not show in mc.9 and asking him to get it removed.
    What should I suggest to user and finance.
    Thanks,
    Kiran

Maybe you are looking for

  • Should i buy a ipod 3g

    Hy guys I always didnt like apple (i like't galaxy's etc more) But i really wanna heve an ipod now since i ♥ apple products  now But the thing is i dont wanna waste a lot of money Thats why i wanna buy an ipod 3generation. But i heard u cant download

  • Showing Donut chart

    Hi Experts, Quick Question - Currently endeca studio supports 2D pie chart . So is there any way to customize in order to show Donut chart instead of 2D pie chart . Any Inputs would be highly appreciated Thanks- Dinesh

  • FLEX Contact Forms

    As the summary states, I have been scouring the internet high and low trying to find a WORKING contact form created in Flex 2. I have yet to see it. And the frustration of building it myself is starting to get to me. So I am asking for the help of an

  • Wl server 6.0 on solaris

    downloaded wl 6.0 for solaris. keep geting disk space not enough error mesg although I have enough disk space. I exported the tmp dir env variable IATEMPDIR as instructed in the install guide. OS is sunOS 5.6, free disk space 3g and mem size 7g. Anyb

  • Guide me please

    HI All, I have 2 yrs of exp in which 10 months in Insurance company and 14 months as Fund Accountant (Hedge Funds). I have recently put down my papers in order to get trained and certified as SAP FI consultant. I'm planning to join Genovate next mont