Office Jet 6700 Premium only prints the same crossword over and over

My wife likes to do the daily crossword. However now it only prints the same one repeatedly. How do I get the EPrint to roll over to the next day? I have tried cancelling and resetting the app to no avail. Any help is deeply appreciated. I even tried the HP paid service. They were no help.

Hi,
It's very easy to add but a bit hard to remove. Please use the following instructions:
    http://h30434.www3.hp.com/t5/ePrint-Print-Apps-Mob​ile-Printing-and-ePrintCenter/Re-How-to-add-or-rem​...
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Similar Messages

  • My HP Office Jet 6700 Premium has suddenly stopped printing from my iPad

    I have a new HP Office Jet 6700 Premium
    It had been working just fine, wireless printing from my iPad.
    iPad shows a window that recognizes the printer, but it does not print.
    There is no error message.
    This question was solved.
    View Solution.

    The steps below typically resolve the issue you’re experiencing:
    1. Power off the printer.
    2. Completely power off the iOS devices (hold the Sleep and Home buttons simultaneously until a message appears asking you to "Slide to power off". Slide across that bar, and it should completely power off).
    3. Power the printer back on.
    4. Power the iOS devices back on.
    5. Try to print again.
    Those steps usually resolve the issue. If they do not, try this additional steps:
    6. Power cycle your router (usually done by unplugging the router’s power cord, waiting 20 seconds, and plugging it back in).
    7. Make sure that the iOS devices and the printer are all connected to the same network, then try to print.
    If I have SOLVED your issue, please feel free to provide KUDOS and make sure you mark this thread as SOLUTION PROVIDED!
    Although I work for HP, my posts and replies are my own opinion and not those of HP.

  • Dissatisfi​ed with HP Office jet 6700 Premium Printer

    I've had a HP Office Jet 6700 Premium Printer for 18 months and have encountered a failed printer head issue which essentially requires full replacement of the printer.  I've seen many other similar reports by others which clearly indicates this printer has a serious problem with the printer heads.  I'm getting ready to replace this printer, which is just 6 months out of warranty, and will seek another vendor to provide printing equipment.  Very disappointed in HP's printer product and will gladly provide input to help others avoid running into this problem.

    Please read this post then provide some details.   What operating system?  What are the error messages on the printer or computer screen?
    Bob Headrick,  HP Expert
    I am not an employee of HP, I am a volunteer posting here on my own time.
    If your problem is solved please click the "Accept as Solution" button ------------V
    If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

  • Wireless is not working on my new HP office jet 6700 premium

    Gents,
    i have a new HP office jet 6700 premium all in one printer and i coneccted to the network via wireless and its works only for 2 minutes and after that its not working via wireless unless i disconnected and reconected again please advice.
    FYI it is working very good by USB, and im using Mac OS X 10.9.3 version 
    Regards,

    Hi Kattoa,
    Welcome to the HP forums!
    I'm sorry to hear your Officejet 6700  doesn't seem to be holding it's wireless connection but I'd be happy to help determine what the problem could be
    I think it would be best if you followed this Printer Does Not Maintain Wireless Connection document as it should be able to help determine why the printer has to be reconnected so frequently.
    Let me know how that goes for you!!
    Please click “Accept as Solution ” if you feel my post resolved your issue, as it will help others find the solution faster
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    **MissTeriLynn**
    I work on behalf of HP

  • HP Office jet 6700 ,trying to print and it will say Printer Ready, Empty Print File !

    I have a HP Office Jet 6700. I'm trying to print a document , it will say prining Untitled . The printer queue will open up and say printer is ready, empty print file,Idle.
    It automatically goes into paused printer. When I try to click on the document itself in the print queue and resume print it gives the same message again.
    The Power on the actual printer is flashing slowly as well.
    I hae restarted my computer and shut down the printer completey multiple times and it still has not worked. I just printed something on this last night so I'm not sure what the probelm is. 
    This question was solved.
    View Solution.

    Hello there! Welcome to the forums @Chinadoll702 
    I read your post about the printing issues you've been experiencing on your Mac running 10.6 and your Officejet 6700. I have a few ideas in mind to get started and let me know the results and we will take it from there.
    Update the Firmware on the printer: Getting the Latest Firmware and Product Updates
    Power reset the printer and make sure the printer is plugged in directly to the wall outlet, avoiding power bars and surge protectors. This ensures the printer is receiving full power and may help greatly.
    Press the Power button to turn on the product.
    With the product turned on, disconnect the power cord from the rear of the product.
    Unplug the power cord from the wall outlet.
    Wait at least 15 seconds.
    Plug the power cord back into the wall outlet.
    Reconnect the power cord to the rear of the product.
    If the product does not turn on by itself, press the Power button to turn it on.
    Make a few copies afterwards and tell me if the copies pause, cancel, do not work, etc.
    Try printing from Text Edit on your Mac as well, and get back to me with the results.
    Good luck
    R a i n b o w 7000I work on behalf of HP
    Click the “Kudos Thumbs Up" at the bottom of this post to say
    “Thanks” for helping!
    Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

  • Help. My iPod nano is stuck on repeat. it will only repeat the same song over and over. How can I change the settings

    Help. My ipod nano is stuck on repeat. It repeats the same song over and over and wont play songs on the same album consecutively. How do I fix this

    Hey cemccarty,
    Thanks for the question, and welcome to Apple Support Communities.
    The option to turn off repeat will depend on your iPod nano model. Here is the information for the latest model, the iPod nano (7th generation):
    (click to view larger images)
    via page 18 of manuals.info.apple.com/en_US/ipod_nano_user_guide.pdf
    If you have an earlier model of the iPod nano, see the relative user guide from this page:
    Apple - Support - Manuals
    http://support.apple.com/manuals/#ipod
    Thanks,
    Matt M.

  • My ipod touch will only play the same song over and over unless you manually fast forward?

    My ipod touch will not shuffle through the songs. It just plays the same song over and over.  All that shows at the top is the info picture.  How do I fix this?

    Do this:
    Play a song.
    Tap the screen once so you see the scrubber.
    To the left of the scrubber, there's a set of two arrows going in a circle - if it's blue, it's set to repeat.
    Click on it once to make it white - no repeat.

  • HP Office Jet 6700-Wirel​ess Printer-Ho​w to change the Printer IP Address to the new ISP's IP Address

    Greetings All,
    I have been using ATT DSL with my HP 6700 wireless printer. I have had no problems with wireless printing (save the replacement ad nauseum of the ink cartridges-another issue I posted some time ago).
    Today I had Comcast cable installed.  (So far I am not impressed with the speed-Note to self-post on Comcast site re this).
    I still have access to the ATT DSL. The HP 6700 stores the IP Address and SSID for the ATT. network.  As long as I am logged into the ATT Network,  the HP 6700 prints fine.
    When I switch to the Comcast network,  it does not print. The IP Address that is stored in the printer is the ATT IP address.
    I have tried the UPDATE IP Address option from the Start menu. It does not work.
    How do I get the HP 6700 to print from the Comcast network? 
    Perhaps the printer cannot be accessed on two networks and must be removed from the ATT network before it can be used on the Comcast network?
    If anyone has encountered this problem and solved it please respond.
    Thanks,
    Chris

    Having similiar problem with HP Officejet 4500 All-in-One Printer - G510g-m. Lost connection to printer when disconnecting ATT DSL and moving to Comcast cable internet service. Comcast technician attempted to assist without success. HP instructions ASSUME that the printer is connected directly to the computer. We have a laptop that connects via wireless from modem, works great. Have the printer connected via Ethernet to Comcast modem. Tried to find Comcast IP address (where is that>), but also could not get the function on the printer itself to allow any change to the existing IP address that I assume is from ATT. Just learned that to get help by phone from HP will cost and was directed to the forum. If you have since solved your issue, perhaps you have some pointers for me. I've also had the laptop cleaned recently and found the HP software disk and have proceeded through the installation process up to not getting a solution. Help please.

  • Web Services could not be Enabled (Office Jet 6700 Premium)

    Hi,
         I've successfully connected my printer the internet via wireless connection. I can print from any computer over wifi. However, I cannot enable web services.
        I have tried every troubleshooting method available under the sun.
         Eg) Manually setting IP Addres and DNS, Restarting, Resetting to Default, Rebooting Router, updating router etc.
        All methods I have tried are also here (http://h30434.www3.hp.com/t5/ePrint-Print-Apps-Mobile-Printing-and-ePrintCenter/ePrint-Apps-Connecti...
    I have read every forum relating to this issue and everyone seems to have had their issue resolved through all one or more of the methods I have already used. I am quite disappointed with having to spend so long getting my product to do what it is meant to do straight out of the box.
    Any further guidance would be kindly appreciated,
                Kind Regards

    Hi there, your frustration is understandable. It sounds like you have exhausted all the troubleshooting steps but if you haven't already, try using the manual DNS values in the image below in the printers embedded web server (EWS) settings. If you've already done this and your printer is only new let me know what country you are in and I'll provide you with a direct number for HP phone support as you may be entitled to a replacement.
    Best.
    If my reply helped you, feel free to click on the Kudos button (hover over the "thumbs up").
    If my reply solved your problem please click on the Accepted Solution button so other Forum users may benefit from viewing the post.
    I am an HP employee.

  • Windows 7 PC connected to HP printer via time capsule. Printer keeps printing the same page over and over

    I am using time capusle and have my husbands Windows 7 PC and my MacBook Pro connected to it. I just purchased a HP LaserJet P1606dn and have connected and printed to it succesfully using Bonjour on my MacBook.
    I have connected through Bonjour to the printer on the PC, but when I print a page, it keeps printing the page over an over. It stays in the que. I also set up my dual boot MacBook/Vista laptop and agai, I have no issues on the MacBook part, but it does the same thing on the Vista Machine as on the Windows 7.
    Does anyone have any ideas how to fix this?
    Thanks!

    Located a solution:
    Go to Control Panel - Printers ---  right click the printer and select Printer Properties.
    Select the PORTS tab and disable Bi-Directional Printer Support.    Seems to work whether the printer is installed either via USB or Cat5 to the Airport Extreme network.
    For HP printers, if that first fix doesn't work, download and install the HP Install Network Printer Wizard  - allow it to replace your 'newer' driver, but check hp.com for step by step instructions.
    Third suggested fix is to download a PCL6 driver, or a different model-driver altogether that is more generic than model specific.

  • HP Office jet 6700 Premium e-All-in- one. Not printing from Mac Pro

    Moved to the Mac printing forum for better coverage.
    Bob Headrick,  HP Expert
    I am not an employee of HP, I am a volunteer posting here on my own time.
    If your problem is solved please click the "Accept as Solution" button ------------V
    If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

    What router? Have you restarted the router?
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • HP Office Jet 6700 Premium All In One

    Printer works but copy function does not.  When copy is selected, it reads "starting to copy" but never does anything.  Have to turn off machine to get it to cancel "starting to copy".

    Hello amw1945! Welcome to the forums!
    I saw your post about how you cannot make a copy. I would suggest checking for a firmware update and completely power resetting the printer with leaving it unplugged for at least 60 seconds. Ensure the printer is plugged in directly to a wall outlet. Avoid power bars and surge protectors to test the copies.
    Getting the Latest Firmware and Product Updates
    If the troubleshooting does not help resolve your issue, I would then suggest calling HP's Technical Support to see about further options for you. If you are calling within North America, the number is 1-800-474-6836 and for all other regions: click here.
    Have a great day
    R a i n b o w 7000I work on behalf of HP
    Click the “Kudos Thumbs Up" at the bottom of this post to say
    “Thanks” for helping!
    Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

  • Print in PDF only Prints the first two pages

    I am have been ahving problems with my creat PDF account, only printing the first two pages, when i print something to PDF from a webpage.  I.E. Pinterest.  It will only print the first two pages and the rest will be blank or incomplete.  I am at the end of my rope and dont know how to fix it.  I recently got Acrobat 9 standard thinking this may help, but the problem still exists, which irritates me more.  Please help!

    Try here: http://forums.adobe.com/community/createpdf
    There people who use CreatePDF on a daily basis there, who know much more about it .

  • How do I enable the e-cloud on my office jet 6700 and set up its email address

    I have a new iPad that I'm trying to enable to print. (I never had any trouble syncing my old one.) I have followed the instructions but it's still not working. It seems perhaps it's because the printer is not set up for Cloud? Yet, There is an icon on my office jet 6700 that indicates it is cloud capable.

    Hi @Mes17333
    Welcome to the HP Support Forums.  I gather that you are trying to print from your new iPad to your Officejet 6700 printer. 
    I am presuming that the printer is connected to your wireless network as you indicated that you were able to print with your older iPad.  To use Apple’s AirPrint feature you only need to have the printer connected to your wireless network and that the router supports Bonjour communication.
    If you are using the HP ePrint Mobile app or the HP All-in-One Printer Remote app, then please click on either app’s name and it will bring up the appropriate FAQ document which will have the trouble shooting steps to get the iPad printing. 
    Please let me know how things turn out.
    Regards,
    Happytohelp01
    Please click on the Thumbs Up on the right to say “Thanks” for helping!
    Please click “Accept as Solution ” on the post that solves your issue to help others find the solution.
    I work on behalf of HP

  • TS3276 Unable to print e-mail messages from Mac book pro directly to my HP ink jet printer.  Can print from Word, Excel, Safari.  E-mail messages only print the date and "sent to" name.

    Unable to print e-mail messages from my Mac book pro directly to my HP ink jet printer.  Can print from Word, Excel, Safari.  E-mail messages only print the date And "sent to" name, the remainder is blank.

    If you haven't done so already, try resetting the printing system.
    Reset Printing System

Maybe you are looking for

  • My ipad is disabled after entering wrong password

    Please help me. My ipad is disabled after entering wrong password. i actually forgot my password and in the course of trying for several times, it became disabled. Please how can i enable and unlock it. I tried connecting to iTunnes on my laptop but

  • Usb interface won't stay connected

    Alrighty, I posted a topic on this same equiptment a few days ago and got help for it. It worked once, and now GB asks me if i want to use the interface when I turn it on. I click "yes" and then it either disconnects or shows that it was never connec

  • SAP XI In Sneak Preview

    I would like to practice SAP XI and i don't have access to SAP System with XI. Does Any Version available in Sneak Preview Contain XI, If so please let me know so that i can download and work on SAP XI. Please provide me some information... Thanks An

  • Versions in CO

    In versions creations in CO there is a option to set each fiscal year . In that there are two options like copying allowed and integrated plannning. For what purpose do we use that options? Pls explain Regards babu

  • Problems to load interpretations in Dreamweaver cs 5.5.

    Hi, i am using  Dreamweaver CS 5.5 to design websites but suddenly i got a problem when opening files. It says: Following interpretation was not loaded because of errors: ASP.htm: contains invalid configuration information. ColdFusion.htm: contains i