Only two channels of 5.1 work

I have Sound Blaster Li've 5. and "Creative Inspire 5. Digital 5700" speaker system.
"Inspire" system is connected to SB Li've via digital DIN.
Options of "Creative Audio HQ" software are set to "5. Speakers". All speakers of "Inspire" system are working well.
The problem is: only two channels (right front and left front) of nedded 5. come to "Inspire" system from SB.
I hope somebody here can help me.Message Edited by Holdy on 0-26-200602:56 PM
Message Edited by Holdy on 0-26-2006 02:59 PM

Katman, the sound source is surround.
after all, the problem solved: i had to turn on effect "Fourpoint/5. DIN" on Inspire Digital speaker systemMessage Edited by Holdy on 0-27-2006 2:59 AM

Similar Messages

  • I use only two channels, have plenty of memory in my hard disk, and external hard drive, no effects, and still having problems with Garage band. Giving messages as you have too many live channels

    I'm frustrated, I am doing everything you recommend, I use only two channels, have plenty of memory in my hard disk, and external hard drive, no effects, and still having problems with Garage band. Giving messages as you ave too many live channels, the disk is slow prepare...can you help?

    Quote from: Richard on 15-November-07, 20:33:05
    tornado2003,
    What you need to do is boot into Safe Mode. Then delete the VGA Drivers.
    After that boot normally and install the latest nVidia ForceWare Drivers
    Take Care,
    Richard
    i guess you missed that:
    Quote from: tornado2003 on 15-November-07, 17:26:52
    ive tryed booting xp in safe mode but it just freezes after it loads up a couple of needed files .
    ive even formatted my hard drive and tryed installing a fresh xp on it but it just keeps locking up when it gets to the "starting windows setup" .(this is just after it loads all the drivers from the xp cd)

  • There is no 5.1 OVER HDMI on the HP PAVILION DV7 only two channel stereo!!!

    Dear HP
    I have a Pavilion dv7 laptop.
    I am able to connect my laptop via HDMI to my Samsung 55 LED. Video transfer is in HD. Sound is also transmitted but only in 2 channel format rather than 5.1 channel format. In the sound settings via control panel I have tried to reconfigure but there is only a 2ch and no 5.1ch setting. The same is the case in the 'Speakers and Headphones' (IDT High Definition Audio CODEC) setting
    The 5.1ch output setting should be present as Windows 7 professional is compatible with this as should be my laptop, and my TV has an inbuilt Dolby Digital processor which conveys 5.1Ch sound to my home cinema unit.
    My home cinema system DOES support and decode Dolby & DTS 5.1. This is connected to my TV via optical cable.
    TV transmissions from Freesat that are in Dolby Digital 5.1 do output correctly in 5.1 via my home cinema system, this is why I know for a fact that my TV DOES output in Dolby Digital 5.1. There is a light on my Home cinema system which confirm the inputted sound is 2ch or 5.1ch.
    There is no error with my TV or Home cinema System - there is a problem with my Pavilion laptop failing to output 5.1.
    Please help!
    Many thanks

    Hi,
    DV7 is a series of dozens if not hundreds of models, what is yours ? Please bear in mind normally HDMI sound on computers go from video cards, not "sound" cards.
    Regards,
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • Only two of three monitors working since upgrading to 10.9.3

    Only two of my three monitors work since installing 10.9.3. I want to roll back to 10.9.2. How should I do this?

    I had already tried that configuration. It was working fine until I upgraded to 10:9.3.  If I boot into the recovery disk volume, all three monitors work. If I boot from a backup/clone of my drive prior to installing 10.9.3, all monitors work fine.
    Any other suggestions will be welcomed.

  • P7800 = two channels?

    I can't seem to find anything on this. Most people who have problems with their speaker system have problems getting sound out of their speakers. I have a problem with NOT getting sound! That is, sound comes from the front when it should only come out the back. Indeed, my computer seems to think that the speaker system is only 2 channels.
    When I try to test the speakers using the Realtek HD Audio Manager, I get sound coming out of all three of my left speakers when it should only come out the front left (or side left, etc.) same with the right. I also get no sound out of the sub when I test it in the program (but it works fine when actually listening to music.)
    When I go to the Windows sound control, I set the speakers to 7.1 Home Theater configuration but when I go to volume control I can only control the volume for two channels. Is that normal? Shouldn't I have volume control for all 8 channels?
    Of course, MP3 files and TV are only 2-channel anyway so when I do those things everything is great, but when I watch a movie or play a game, I would like to actually get the full 8-channel experience, and not have sound coming from all speakers when it should only come from one.
    Can anyone help with this at all? I realize that this is likely not an issue wtih the speakers, but I'm posting here because I'm not sure who else to ask. The sound card is just integrated with my motherboard, and yes I have all of my drivers up-to-date. I am just so frustrated because I don't get why it's not working!! Please help.

    God, this is so frustrating.
    After about 20 emails sent back and forth between customer support, one man finally seemed to understand my problem. He told me to uninstall the drivers, boot Windows into "Clean boot" and re-install the drivers there. I did this, and it worked!! I couldn't believe it. Sound was coming through all speakers properly on the tests. When I clicked the rear-left speaker in the Creative Console, I got sound only from the rear-left. Beauty!! I was stoked. So then I'm going with it for awhile, testing it intermittently to ensure it was still working, when it stopped. Some time today, it went back to its old habit. Sound only from the front two unless I enable CMSS, at which point I get all speakers but only two channels. Testing "rear-left" results in sound coming from the front left (if CMSS disabled) or coming through all three left (if CMSS enabled.)
    I was extremely annoyed, but figured I'd just do the fix again. Except this time it didn't work. Seriously, I did the exact same thing that fixed it last time, and this time it didn't fix it. I can't even begin to describe my frustration at this point. Can nobody help me?! I have tried so many things at this point. I have re-installed the drivers in so many ways, under so many conditions. I uninstalled some other programs. I completely removed all CREATIVE software, rebooted, went into clean boot, installed the drivers, rebooted, and still it doesn't work. Why the heck did it work that one time but never again?! ARRRRRGGHHH. I am just so fed up.
    PLEASE somebody help me.

  • Trying to use the same ground for more than two channels (RSE configuration) with usb 6000

    Hello,
    I'm currently trying to set up a LabView code in order to get readings of voltage using 5 different locations simultaneously. I want to only use the first location as ground and obtain 4 voltage measurements between the ground and each one of the other 4 channels. I'm using a usb 6000 which for now allows me to use the same ground for only two channels. Is there a way to use the same ground for 4 channels?
    Thank you,
    Maria

    You're right it is confusing the way I describe it so I ahve attached some pictures of the set up. The first figure is the cell filled with soil and the 5 probes inserted in it. The anode is placed at the left end of the cell and the cathode at the right end but they do not appear in the figure. I'm trying to use location 1 as gournd and take measurements of voltage from the following pairs: 1-2, 1-3, 1-4, and 1-5. The second figure is the DAQ I'm using. When I was trying to set up the RSE configuration, it was ussing ground A for the channels 6 & 7 (locations 2 and 3 in figure 1) but ground B for channels 4 & 5 (locations 4 and 5 in figure 1). What I am asking is which is the best way to use the signal from location 1 as the ground for all 4 channels. Is this more clear?
    Thank you for your time!
    Maria

  • My MacBook Air headphone jack only left channel works

    Builtin speakers are working fine on my MBA 2012, but when I plug any kind of headphone into the jack, only left channel works. If I tune output balance to right, then sound nothing.
    I found there are only four metal contacts in the jack, two on each side, then one for ground, the other one for left channel, none for right channel,  what about yours?

    At last, found it isn't a problem, actually any 3.5mm headphone of standard can work, just plug into the jack fully ( only one mm left ) .  enjoy ~~

  • [svn:bz-trunk] 13716: since include-read-only is a server global setting, we can't have two channels with different value.

    Revision: 13716
    Revision: 13716
    Author:   [email protected]
    Date:     2010-01-22 09:26:12 -0800 (Fri, 22 Jan 2010)
    Log Message:
    since include-read-only is a server global setting, we can't have two channels with different value.  remove the test for the include-read-only false.  update the service-config.xml as well.
    Modified Paths:
        blazeds/trunk/qa/apps/qa-regress/WEB-INF/flex/services-config.mods.xml
        blazeds/trunk/qa/apps/qa-regress/testsuites/mxunit/tests/remotingService/dataTypes/ReadOn lyTest.mxml

    You can give this a try on your Ultimate machine.  While these are said to be for Vista, I used it on my Win 7 machine just fine and it fixed the problems I was having.  Hope it works for you.
    The problem is that Vista, by default, will only use NTLMv2 for authentication, which is not supported by Mac OS X's Windows Sharing service.
    The other problem is the Minimum Session Security for NTVLM SSP based Clients.
    To get around this:
    1.     In Vista, open the Control Panel
    2.     Switch to "Classic" view
    3.     Double-click Administration Tools
    4.     Double-click Local Security Policy
    5.     Or Secpol.msc
    6.     Expand "Local Policies" and select "Security Options"
    7.     Alternate : Type secpol.msc to get editor up then
    8.     Locate "Network Security: LAN Manager Authentication Level" in the list and double-click it.
    9.     Change the setting from "Send NTMLv2 response only" to "Send LM & NTLM - use NTLMv2 session if negotiated"
    10.     Network Security: Minimum session security for NTLM SSP Based (including secure RPC) Clients
    11.     Change the setting from "require 128 bit" to unchecked (No Minimum)
    12.     Click OK
    the real difference between vista and windows 7 procedure is 10 and 11

  • Only 1 channel work

    I replaced the sound card in my computer and only one channel out of two works. I was only able to plug (larger) of the two plugs from the motherboard into my card. Is this the problem? The board has two wires with white plastic rectangular connectors, one big(installed) and one small(does not fit new card).

    Hi,
    Whats the card you have?
    John

  • I have two time capsules, one for work and one for home, how do I set up the work time capsule to only back up my work files?

    I have two time capsules, one for work and one for home, how do I set up the work time capsule to only back up my work files?  Also, how do I add co-workers to my work time capsule and wife to my home time capsule?  Thank you!

    You cannot have two different TC setups.. at least until Mountain Lion.. it did introduce some changes but I am not sure if you can setup two different configurations for TM.. you can use two different devices to back up to. I doubt this will help you.
    You might be better using a real backup software.. superduper, CCC, chronosync etc.
    The TC by default is available to any Mac in the network to do backups. TM will sort itself out and put each computer on a different backup. These are kept in separate sparsebundles.. so that is all fine.

  • Sound output only on two channels but system set to 7.1 sound

    LabVIEW2011, Win7, Creative audigy 2 soundcard and/or USB sound device  set to 7.1 sound
    The sound2.llb ... info found the card but only allow to open 2 output channels giving error 4811 when trying to configure for more than 2 channel output.
    However the OS audio test 'ping' every speaker
    Any hints welcome
    I attached my test vi. you will need at least one wav sound file ... (or try to rescue the diagram values... )
    It runs with one or two channels but fail on higher channel counts.
    Greetings from Germany
    Henrik
    LV since v3.1
    “ground” is a convenient fantasy
    '˙˙˙˙uıɐƃɐ lɐıp puɐ °06 ǝuoɥd ɹnoʎ uɹnʇ ǝsɐǝld 'ʎɹɐuıƃɐɯı sı pǝlɐıp ǝʌɐɥ noʎ ɹǝqɯnu ǝɥʇ'
    Attachments:
    Read wav and play nchannel v2.vi ‏375 KB

    Hi Henrik,
    what I can recommend to you is directly using the Driver API of your soundcard device if available.
    Kind regards
    TSP 
    Kind regards
    Tobias S.

  • Need only two decimal places, but BigDecimal isn't working

    Hello again. This time I've got a problem with getting only two decimal places. I tried using BigDecimal but when I compile it, I get an error "cannot find symbol class BigDecimal" and a "cannot find symbol variable BigDecimal".
    Grrr... I just want my value to have only 2 decimal places before it ends up in my text field.
    Any help will be appreciated.
    - Phonse
    if (ostuff1.equals("amt tendered"))
                     finalamt = total1 * 1.12;
                     change = cash1 - finalamt;
               BigDecimal finalamt2 = new BigDecimal(finalamt);
                  finalamt2 = finalamt2.setScale(2, BigDecimal.ROUND_DOWN);
                  BigDecimal change2 = new BigDecimal(change);
                  change2 = change2.setScale(2, BigDecimal.ROUND_DOWN);
                  finalamt = doubleValue(finalamt2);
                  change = doubleValue(change2);
                     addItem(String.format("Amount Tendered:          "+"P "+finalamt));
                     addItem(String.format("Change:                     "+"P "+change));
                   }

    @ georgemc
    Isn't it better to import whole packages instead so
    you can have everything available when you call them?
    I mean, it's kinda hard to import individual classes
    everytime you need to call them.No. You can get conflicts when importing complete packages. If you importjava.awt.*;
    java.util.*;and then declareList list;the compiler does not know which List you meant, java.util.List or java.awt.List.
    Offtopic @ prometheuzz
    LOL. When I was a kid still playing my Playstation I
    wanted to have a career in computers when I got to
    college. Now I'm 14 and a 3rd year high school
    student and I just got a reality check -- computers
    just isn't for me. And alot of those professionals
    say Java is the "easiest" programming language. O_O
    Meh. I'll just follow my other dream of becoming a
    chef. Just seems like my parents won't like it...
    Bleh... Two more years... Two more years...Sure, but if you like programming, work (hard) for it. Most people have to work hard in order to become good at something, no one is born as a programmer. This goes for becoming a chef as well.

  • Two finger scrolling does not work ONLY on Firefox

    This just started today, suddenly my two finger scrolling doesn't work but only when I'm in Firefox, offline and on Safari and Chrome it's fine. Restarting Firefox only fixes it for a few minutes, then it stops working again. All of the suggestions I've found that I've tried haven't worked, please if anyone could help and also break it down fairly easily, I'd really appreciate it.

    ''guigs2 [[#answer-674567|said]]''
    <blockquote>
    Does this happen in Safe Mode?
    '''Try Firefox Safe Mode''' to see if the problem goes away. [[Troubleshoot Firefox issues using Safe Mode|Firefox Safe Mode]] is a troubleshooting mode that temporarily turns off hardware acceleration, resets some settings, and disables add-ons (extensions and themes).
    If Firefox is open, you can restart in Firefox Safe Mode from the Help menu:
    *In Firefox 29.0 and above, click the menu button [[Image:New Fx Menu]], click Help [[Image:Help-29]] and select ''Restart with Add-ons Disabled''.
    *In previous Firefox versions, click on the Firefox button at the top left of the Firefox window and click on ''Help'' (or click on ''Help'' in the Menu bar, if you don't have a Firefox button) then click on ''Restart with Add-ons Disabled''.
    If Firefox is not running, you can start Firefox in Safe Mode as follows:
    * On Windows: Hold the '''Shift''' key when you open the Firefox desktop or Start menu shortcut.
    * On Mac: Hold the '''option''' key while starting Firefox.
    * On Linux: Quit Firefox, go to your Terminal and run ''firefox -safe-mode'' <br>(you may need to specify the Firefox installation path e.g. /usr/lib/firefox)
    When the Firefox Safe Mode window appears, select "Start in Safe Mode".
    :[[Image:Safe Mode Fx 15 - Win]]
    '''''If the issue is not present in Firefox Safe Mode''''', your problem is probably caused by an extension, theme, or hardware acceleration. Please follow the steps in the [[Troubleshoot extensions, themes and hardware acceleration issues to solve common Firefox problems]] article to find the cause.
    ''To exit Firefox Safe Mode, just close Firefox and wait a few seconds before opening Firefox for normal use again.''
    When you figure out what's causing your issues, please let us know. It might help others with the same problem.
    </blockquote>
    The same issue happens on Firefox 35.0 running in safe mode, Mavericks 10.9.5, both with Magic Mouse and normal standard mouse...
    It's unbeliaveble this issue is going on since more than one year ago, I can find people complaining about it since December 2013!
    Oh, one more thing: I don't have a two finger swipe configuration, I have single finger swipe, so the actual problem is about scrolling the page in itself (considering I've tested it with a normal standard mouse as well....).

  • HT1476 I have problem with my Iphone 4S, only after updating the OS 7.X. My Iphone battery charge is losing down in a minute. My battery charge is just decreasing from 100% to 10% in less than two hours, without any application works. pls do help me out i

    I have problem with my Iphone 4S, only after updating the OS 7.X. My Iphone battery charge is losing down in a minute. My battery charge is just decreasing from 100% to 10% in less than two hours, without any application works. pls do help me out in this.

    Hi melvin victor,
    Welcome to the Support Communities!
    The information below may help you troubleshoot your iPhone battery issue:
    iPhone Battery and Power - Apple Support
    http://www.apple.com/support/iphone/repair/battery-power/
    Battery & power
    Is your iPhone battery draining too quickly or not holding a charge? Try restarting it first. You can also adjust several settings to extend the battery life of your iPhone.
    I hope this information helps ....
    - Judy

  • Only one channel working - fixable?

    Recently my ipod starting playing only one channel through headphones or a speaker jack - eg I can hear only whatever is coming through the left side speaker. I've verified that the problem is with the ipod, not the headphones. However, if I put pressure from a specific angle on the headphone cord right above where it connects to the ipod, both L and R channels work. This goes away again when the pressure is released.
    Has this happened to anybody else? Is it a fixable problem?
    Thanks!

    You need to replace the headphone jack on the iPod.

Maybe you are looking for