Opinion of K8N Neo Platinum?

G'day:
I want to get upgrade my ASUS K8V Deluxe MB for something that will lock the PCI and be able to OC beyond 10x210. This system has been running for over a year with 2x512 Infineon RAM, 2-160Gb Wd SATA (RAID 0), 2x80 GB IDE, ATI 9200, LG 2x DVD RW+/-.
With my 3200+ clawhamer (+stock HS) my options after some reading are the K8N Neo Platinum or a DFI board which was rated well. I've noticed some issues throughout the board and I already have a K8N Neo2 Platinumso am aware of some of them. I know I'll have to redo the RAID and have some fun playing around with the IDE/SATA to get them all to work
What is your opinions of this board, is the change worth it?
TIA.

I have a pretty high opinion of it... I've only been into the 64 stuff for a couple of weeks. But I've gotten really terrific results with it as an OC'er
Partly because of some good parts & mostly by some good help & advice.
Check out this thread & see why - http://forum.abit-usa.com/showindex.php?s=&postid=462681#post462681
Look for the last screenshot towards the middle/bottom of the page. 2.61Ghz with a 3000+, 90nm on air bodes well for it's potential. I was shocked.

Similar Messages

Memory Corruption on K8N Neo Platinum - HELP!

I am having some problems with my cousin’s computer that I built for her last September. She brought me the computer because she got an error that the system32/config/system file was corrupted and couldn’t boot the computer. I got the file replaced and got the computer re-updated to where it worked. Then the same thing happened again. This time I did a Windows reinstall and the computer acted a little sluggish and iffy so I did a memory test. I found the memory was all corrupted.
First here are the pc specs:
MSI K8N Neo Platinum with 1.7 bios
Athlon 64 3000+
120GB Seagate SATA hard drive
NEC DVD Burner and Samsung DVD ROM
Radeon 9550
512MB Corsair Value Select 2.5CL DDR400
Antec 350W psu and Antec Case
I ran Memtest86+ v1.6 and the Corsair stick had errors in Test 3, 4, 5, and 7. In tests 3 and 4 there are 50 errors but at the 98% of Test 5, the errors jumped to 146,432 and they were 500.8MB part of the stick. I got the same results when I moved it to DIMM2 slot. I also get the same results when the HT is at 1x or 4x.
I tried a known working 512MB stick from my sisters Athlon XP 2500+ pc in the A64 pc. It is a Mushkin PC3200 Basic stick. I get errors only at 98% of Test 5 which amounts to 109,568 errors. Same results in DIMM2 slot.
But when I test the Mushkin in my sisters pc, it has no errors. But the Corsair stick in the AXP pc gets errors on Tests 1, 3, 4, 5 (only at the 98% mark), 6, 7, 8 but only a total of 317 (a lot less than 146,000 in the A64 pc.)
So, I know the Corsair memory is bad, but now something is also wrong with the motherboard and /or cpu right?
If you need any more info let me know. I’m new to the forums and they look very helpful.
Thanks.

Quote from: blazing storm on 23-August-05, 05:30:00
Look in the bios and loosen up the RAM settings. Make sure the RAM isn't being stressed into settings that are too hard for it to handle.
See I told you to loosen it up...
I speak from experience as the same happened to me and loosening settings stopped errors.
Glad you managed it, well done...

300gb doesn't work on K8n neo platinum

Hi guys! This is my first post ever so please bear with me if it confuses the hell out of everybody
Here's my setup:
Antec 480w
3400+ amd64 1mb L2 cache 754 pin
MSI K8N Neo Platinum
1gb Crucial Ballistix pc3200
2 x 36gb WD raptors
1 200gb IDE seagate 7200rpm 8mb buffer
ATI 256mb 9800xt
pioneer dual layer dvd-108
lite-on CDR
Floppy drive
Ok here's the problem. Everything on the top works fine! My computer has been on for 2 months straight without nothing happening. Now when i finally turned it off, I decided to add the new 300gb maxtor SATA 16mb buffer drives. After I did that, and formated it, it worked for a time. Most of the time after i restart or turn off my computer, windows does not post; it locks up to that screen that says "Windows XP" with the bar scrolling on the bottom of it. Some times it just sticks forever at the beginning bios post with the drives being dectected.
My raptors are hooked up on raid 0 on SATA 3 and 4. My optical drives are on IDE-1. My seagate 200gb os on IDE-0. The moment i added the 300gb maxtor SATA to SATA port 1, that is when i started having the problems.
I checked to make sure everything is right:
1. Check boot prioritys.
2. Check jumpers.
3. Updated bios, even the beta-bios.
4. I made sure all the settings are correct. I even cleared CMOS to do it all over again just to make sure.
5. Installed latest drivers and SP 2 (oh i'm running windows XP sp2 by the way)
I was thinking that SATA 1-2 ports are shared with port IDE-0. If that is true, then that's probably why the computer is getting a confused. I don't know, i talked to my friends and they said they had all the SATA ports used up and also the IDE ports. I'm not sure, sometimes i can get windows to post but with a couple of restarts (54 restarts to be exact :P ) Also if it does post, windows freezes sometimes when i try to add new stuff to the 300gb.
I think that's everything. I hope somebody could help me because i'm about to throw this HD out the window, jump on it until i can't breath anymore, then light a cigarette with a happy smile on my face...

Quote from: sauria on 14-March-05, 11:32:18
Yeah, just doesn't like the 16M cache drive
I'll receive a maxtor 200gb 16mb sata (6B200S0) by the beginning of the week so I'll probably be working on the problem too

*UPDATED 7/15/04* Complete guide to bioses, drivers, and needed files for the MSI K8N Neo Platinum

Complete newbie's guide to bioses, drivers, and needed files for the MSI K8N Neo Platinum:
Last Updated: Thursday July 15th, 2004
Bioses:
(In order of date released.)
1.1b3 - (Download)
- Pre-1.1, given to reviewers to use in their reviews and benchmarks.
- Less stable, but supposedly you get slightly better overclocks.
1.1 Official - (Download)
1. This is AWARD BIOS release
2. This BIOS fixes the following problems of the previous version:
- Memory always run DDR 200 when install single side DDR on DIMM2 & DIMM3.
- Windows 2000 can't format the RAID IDE HDD when plug in Promise 378 controller.
1.2b5 - (Download)
1.2b7 - (No Download Yet)
1.2b10 - (Download)
- First attempt to fix false temperature readings. Fixes it for some people with Newcastle cores and doesn't fix it for anybody with Clawhammer cores.
1.2b12 - (Download)
- Second attempt to fix false temperature readings. Fixes it for some people with Newcastle cores and some people with Clawhammer cores.
1.3b1 - (Download)
- Another attempt to fix temperature problems?
- Possibly fixes cold boot/power light issues?
1.2 Official - (Download)
1. This is AWARD BIOS release
2. This BIOS fixes the following problems of the previous version:
- System can't resume from S3 sometimes when install USB device.
- Support K8 Sempron CPU.
- Turn off keyboard LED in S3.
--Quick Guide for flashing BIOS, provided by MSI--
1. Create a MS-DOS boot diskette, then copy the the .exe and the bios file to the floppy disk. Both of these files can be found in the package you downloaded.
2. Press "Delete" and go to BIOS setup while computer bootup.
Check BIOS advanced features and see if BIOS flash write control is enabled
(This option must be enabled. If you can not find this setting, it means the BIOS can be
flashed.)
3. Boot from MS-DOS boot diskette and get a:\> prompt.
4. Type "", then press ENTER
5. The flash program will then ask "Do you want to save BIOS?", please press "N" for no. The when you see Press 'Y' to program or 'N' to Exit, please press "Y" to continue.
6. After flashing complete, remove floppy and reset the system .
7. Press DELETE or F1 when prompted at first reboot after flashing.
8. Load BIOS optimized defaults, then save settings and exits.
Drivers & Needed Files:
(Note: All these drivers are for Windows XP.)
Leaked Nvidia nForce3 Chipset Drivers Version 4.40
(Please use at your own risk, these are LEAKED drivers. Password for the .zip file is "ocworkbench rules". Also, you will need to rename the WinXP_2K folder in IDE to either WinXP or Win2K else the installer doesn't pick it up.) Thanks for the link Wonkanoby!
*NEW* Leaked Nvidia nForce3 Chipset Drivers Version 5.03
More leaked drivers? Seems some parts of the drivers are older and some are newer.
1. Windows XP Service Pack 1A (Web Install) -or- Windows XP Service Pack 1A (Full Install)
2. Microsoft DirectX 9.0b (Web Install) -or- Microsoft DirectX 9.0b (Full Install)
3. Nvidia nForce3 Chipset Drivers Version 4.24
4. AMD Athlon 64 Processor Driver Version 1.1.0.14
5. Nvidia Video Card Driver Version 56.72 -or- Omega Nvidia Video Card Driver Version v1.5303
(The Omega drivers are third party drivers optimized for gaming, most prefer these over the standard Nvidia drivers.)
5. ATI Video Card Driver Version 4.7 -or- Omega ATI Video Card Driver Version 2.5.51
(The Omega drivers are third party drivers optimized for gaming, most prefer these over the standard ATI drivers.)
6. Onboard Sound Driver (Realtek AC'97 Audio Codec) Version A3.61
It is HIGHLY reccomended that you install the drivers/needed files in the order listed above. Please note that there are two #5's because you either install one or the other depending on your video card, do not install both of them.
You will come across a problem here though. You can't install the chipset drivers without installing the Windows service pack and DirectX first, but the Windows service pack and DirectX installs need the internet to download files and you won't have working internet until you install the chipset drivers. Here's what I did to get around this. Instead of downloading the web install versions of Windows service pack and DirectX, download the full version and and put them along with all the other drivers on a backup hard drive or burn them to a CD, this way you will have all the drivers you need when it's time to install them and none of them will require the internet to download files.
Another note when installing drivers. Apparently the Nvidia chipset drivers also come with drivers for the onboard sound, but people seem to agree that the Realtek onboard sound drivers are better. When you are installing the Nvidia chipset drivers, just be sure to uncheck the box for sound drivers when it asks you which drivers you would like to install. Now you can safely install the Realtek drivers without any chance of conflicting sound drivers. Thanks for the tip Wonkanoby!

Quote
Originally posted by RLiu818
Quote
Originally posted by Deviation56
Quote
Originally posted by RLiu818
You CAN install the nforce drivers BEFORE installing SP1. The only requirement to install the nforce drivers is DX9.
So is SP1 still recommended to install before the nforce drivers?
The installer still reccomends to install it beforehand for full USB 2.0 functionality... I would have put what you said in there but I wanted to keep it as simple as possible.
oh. IIRC the installer just says USB 2.0 will be fully functional after SP1 is installed. So after you install SP1 you go into device manager and u click update driver and it will auto search and update the driver.
Simplicity-wise, i guess its pretty much equal. It might take less preparation to just copy DX9 full onto a CD and install that first, then nforce driver, then right away you have yoru internet connection.
but i dunno.. i guess i will try it your way this time when my RMA"d board comes.
i will be fomratting and doing a fresh install later on today and will let you know if i come across any problems

Pen drive as A: - K8N Neo Platinum?

Is it possible to make a pen drive appear as A: on the K8N Neo Platinum?
My floppy has failed, and I am thinking of replacing it with a pen drive. I'd like it to appear as A:, so that it can be used for the BIOS recovery procedure that looks to that drive.
Thanks in advance.
[EDIT] Now have the flash drive and it boots as A:

Is it possible to make a pen drive appear as A: on the K8N Neo Platinum?
My floppy has failed, and I am thinking of replacing it with a pen drive. I'd like it to appear as A:, so that it can be used for the BIOS recovery procedure that looks to that drive.
Thanks in advance.
[EDIT] Now have the flash drive and it boots as A:

Wake on LAN/Keyboard wake for a K8N Neo Platinum - how do I use this?

I've got a K8N Neo Platinum motherboard that I am using in my home theater PC and I was hoping to enable either the wake on lan or keyboard wake functions so that they could be controlled via a remote control. For now disregard what the overall outcome I want to achieve is... what I want to know is if enabling the WOL and/or keyboard wake function will allow me to turn on the PC from a completely powered down state as opposed to just powering up from a sleep/hybernation mode. I have read people with other motherboards have been able to power up by using their keyboard, mouse or even WOL when the computer is totally shut down. I'm trying to avoid leaving the PC in a sleep/hybernation mode due to electricity usage. Does this motherboard have the ability to power up when the whole system is shut down?
Also, what key on the keyboard is used to wake up the computer? The manual and bios instructions say nothing about what key needs to be pressed to wake it up.

I know you can set various wake options in the bios. Check there!
You can wake up the computer by wriggling the mouse or pressing any key, if the options are enabled in the bios.
Hope this helps

Turn on PC with keyboard [K8N Neo Platinum]

Is it possible to turn your pc on by pressing a button on your keyboard? I have a friend with an old pc (1,5 ghz P4), and he claims that he can turn his pc on that way.
So technically I'm asking you if you know how to do that. Is there a BIOS option in which you can configure the keyboard button on which your computer will respond and go on automatically? That would be very handy.
My motherboard is the K8N Neo Platinum with a 3000+ socket 754. He has an ASUS motherboard.
Thanks.

Check the manual. It should be an option in the bios. I have it in my bios for my board, but when I helped someone put together their machine with a K8N Platinum 2, I didn't see this as an option in that bios. It may be that power on by keyboard and/or mouse is not an option for your board.

K8N Neo Platinum not passing POST

Hello,
I have just bought an MSI K8N Neo Platinum OEM and it will not pass POST. I have gone through all the items in the Sticky section, but still it won't pass. I don't know what to do.
Here's the hardware I have hooked up:
MSI K8N Neo Platinum motherboard (has "MS-7030 VER:1" written on it)
Athlon 64 3000+ CPU, 512 K L2 Cache (ADA3000AEP4AP)
Kingston RAM (KVR400X64C3A/512)
Radeon 7200 graphics card (about 4 years old)
Seasonic S12 380 PSU
Thermalright XP-90 heatsink w/ 90mm Nexus fan
I have hooked up the 24-pin power cable to the 20-pin motherboard slot using the 24-to-20 pin adaptor supplied with the PSU.
The 12v 4-pin CPU power cable is also plugged in.
The graphics card is plugged into the AGP slot. There is no other power connection needed.
I have installed the CPU with a Thermalright XP90 heatsink and a Nexus 90 mm quiet fan.
I have hooked up the fan to the motherboard C_FAN1 slot.
I have installed the RAM (Kingston KVR400X64C3A/512) into DIMM slot 1.
I attached the case fans to the power supply and hooked up the case speaker.
I have also hooked up the front panel power and reset switches.
I bought the motherboard OEM, so it did not include a D-bracket. I have built a pseudo-D-bracket using two-colour LEDs and plugged it into the D-bracket slot.
With this work done, I plugged in the power supply. The power supply has an on/off switch on the back. As soon as I turn on the switch, the computer tries to boot up. All the fans start spinning (power supply, CPU cooler, case fans, video card fan). Nothing appears on the screen. The case speaker emits a long beep, waits about 5 seconds, then beeps again, and continues this pattern forever. The documentation says that this indicates a memory issue.
My homemade D-bracket shows the following: initially, all the LEDs are red. Then, the LED across JLED1 pins 7 & 8 turns green (with all other LEDs red). I assume that this corresponds to LED 1 being lit, although it really looks like it should be LED 4. Next, the LED across JLED1 pins 5 & 6 turns green (with all other LEDs red). Once again, I assume this corresponds to LED 2 being lit, although it looks like it should be LED 3. I looked this up and the documentation indicates a memory error. To solve the problem, I have tried the following things:
1. Hitting reset. Same boot sequence.
2. Clearing the CMOS using the JBAT1 jumper. I left the jumper at "clear data" for about 10 minutes, then switched it back. Same boot sequence as before.
3. Clearing the CMOS by removing the battery. I left the battery out for 3 minutes, then 30 minutes, then 8 hours. Same boot sequence.
4. Removing the motherboard from the case. I placed the motherboard on the anti-static bag it came in. Repeated steps 1, 2 and 3. Nothing.
5. Move the RAM to DIMM slot 2 or 3. Tried steps 1, 2 and 3 again. The boot-up sequence was the same.
6. Different RAM. I have also tried using OCZ 400 MHz 512MB unbuffered DDR memory (OCZ400512V3). Performed steps 1-5 with identical results.
7. No RAM. Same boot problem.
8. No video card. Ditto.
9. No RAM or video card. Exactly the same as before.
As far as I can tell, all components are supported. The only item I am very unsure of is the graphics card. I do not have the exact specifications on it. When it is in my other computer, the driver details identify it only as a "Radeon 7200". However, it does have the "golden finger" shown at www.msicomputer.com/support/sup_tshoot.asp#1_3. Even if the video card is not compatible, it seems like the beep codes and D-bracket codes both indicate memory issues.
The only thing that I have noticed that is weird (other than the fact that the computer won't pass POST) is that when I turn on the power supply, the computer immediately boots up. I don't know whether or not this is normal.
Lastly, I do not know the current BIOS version. Is it possible that the BIOS is an early version that does not support my memory/CPU/video card? I bought the mobo OEM, so I do not know what BIOS it has loaded. Is there some way I can figure this out without passing POST? This is driving me absolutely insane.
Thank you for your help,
Kyle Renwick

Make sure the fan you are using for the xp90 is supporting RPM readouts .
Then try another AGP gfx card , sometimes you can have a no post due to that the graphics adapter wont start .
Take the system bare bone ( mobo + cpu + ram + gfx )
Have any award beep codes ? , note them down and decode them against
http://bioscentral.com/beepcodes/awardbeep.htm
Still stuck !
Remove AGP + ram too .
The mobo shall beep (endless beeping )
Insert the ram , the mobo shall beep - missing gfx .
Got this far and you know cpu + memory initialize but have problems with gfx or other devices
later in the post/init process .
Do not have any usb devices connected to internal or external connectors ,
note that the USBOC pin un JUSB1/JUSB2 is NOT to be connected .
Also try altering between ps2 and usb keyboard as this also has caused non post situation for people .

New Windows XP 64bit, but no drivers for K8N Neo Platinum

Hello,
I have a MSI K8N Neo Platinum with an AMD 2800+. Just received the new Windows XP 64bit edition after attending a trade show in Houston. Used Partition Magic to make a separate partition on my SATA 400GB HD, knowing there was possibly going to be a problem. This is the final release, retail packaged, not the Beta.
The only drivers found was for my MSI Nvidia 5600 AGp video card. No other audio, Nvidia chipset or board drivers are plug & play. Onboard LAN isn't even found.
Any drivers out yet? I figure i'll have to wait. Can't get updates either bacause it won't detect onboard LAN or a Linksys or 3Com PCI card I tried also.
Woodrow

There most certainly are nVidia drivers. The only thing that there aren't drivers for currently is the onboard sound. This, combined with lack of driver support for my peripherals (webcam and printer) are why I haven't made the switch.

"error loading operating system MSI K8n Neo platinum

OK,
System will post, according to MSI Website I have the latest Bios version.
I can boot from CD.
The only odd item is that I am using the HD that I took out of my old computer with windows already on it.
Tried re-installing windows XP. It went through the loading process and then rebooted. Same error message appears.
Also, is 48 degrees normal for idle temp on CPU AMD 64 3400? 36 degrees NB temp ok?
Oh, yeah, I have a floppy installed, CD-ROM, CD RW, all non SATA. Using IDE cables.
Video is Asus V9980 ultra GeForce FX 5950.
MSI K8N Neo Platinum
AMD 64 3400
Hercules 600 W PSU
WD 80gb HD
Generic CD-Rom
Sony Cd-RW
2 x 512 crucial 400 ddram slosts 1 and 2
Asus V9980 ultra GeForce FX 5950 256 TVD
Do I need to clear bios and re-start?
HD is on it's own cable in IDE 1
Cds on IDE 2 shared.
let me know what you think.
The other related posts I read, people were using raid or multiple OS. I'm not.

I had the same issues as you sometimes Windows would install and sometimes it wouldn't the problem was related to ram. I had my ram in slots one and two like you did and I moved the ram to slots 1 and 3 and now the machine is rock solid stable.
I think most of the problems people are having are actually more ram related than anything else.
So try moving the stick of ram you have in slot 2 to slot 3 and see if this solves your problem. This solution is on forums somewhere I am just not sure where.
Take care,
Bob

K8n Neo Platinum non-booting SATA RAID setup question

I've spent several hours searching an reading trying to find out how to setup a non-bootable SATA RAID. All I can seem to find are posts about bootable installs using F6 and the drivers on a floppy.
I have setup the disks in the bios an defined the array an everything checks out. But when I boot back to WindowsXP it only sees 2 drives that it cannot find drivers for even if I point it to the correct Nvidia directory. I attempted to just reinstall the drivers but that caused a Bluescreen from a corrupt driver file that I then had to go into the repair console to copy from a floppy.
The manual an a couple of posts here say that I should go into Admin Tools-> Disk Management an it will then popup a wizard. But I'm not getting that far.
I currently have the disks on SATA 1 and 2 but will move them tonite because I've read its better for them to be on 3 and 4.
This is on a K8N Neo Platinum 7030 on Windows XP SP2. If anyone could help or just point me to where I can find help it would be greatly appreciated.

When the raid controller is enabled in bios and you start windows you can install the nvidia raid driver
from within windows .
Use the add hardware wizard from control panel .
Start the add-hw wizard .
Yes i have connected the hw - next .
Add a new hw device (bottom of the list ) -next .
Install the hw that i select manually from a list - next .
Select scsi/raid controller - next .
Choose have disk .
Then browse for the location of the nvraid.inf file

K8N Neo Platinum keeps shutting down

I have just built a new system with a K8N Neo Platinum, Athlon 64 3400+ with retail heatsink and fan, 1GB of Corsair TWINX1024-3200C2 DDR400 memory, eVGA GeForce 6800 GT, two 80 GB Maxtor SATA drives in an Antec Sonata case with its TruePower380 watt PS, and my existing NEC 2500 DVD-RW and a DVD-ROM drive and floppy. The system keeps shutting down before I can get WindowsXP installed. It seems to be a heat issue, since its runs the longest after a lengthy shut down, but the bios hardware monitor shows the system temp stable at 33 and the CPU temp at 39.
If I let it idle, it continues to run, but it frequently shuts down when I put a load on it, such as saving the bios configuration or starting Windows during XP setup. I have been able to get XP installed once and started to install the Nforce drivers, but it shut down in the middle of this. Windows files seem to be corrupted frequently. It seems to be somewhat better after I pulled the Athlon heat sink and reapplied a thinner layer of Arctic Silver II. I note that the heatsink does not attach as tightly as the one on my Athlon 1800+. The heatsink fins always seem to be cool to the touch. I notice that the machine usually (but not always) shuts down on a keystroke. I am using a PS/2 keyboard since my USB keyboard doesn’t seem to work.
I understand this motherboard has some issues with temperature sensing, and I would like to get XP installed so I can flash to a later bios and try some moderate overclocking.
I am considering going to an aftermarket CPU cooler, installing a larger power supply, or replacing the MB. I am also considering switching the RAID configuration on the SATA drives from 0 (striping) to 1 (mirrored) or just turning off the RAID function until I get this fixed. Any help would be greatly appreciated.
Trickster2

Thanks for the suggestion. The Antec 380 has 18 amps on the 12 volt rail, 35 on the +5 and 28 on the +3.3, and I have seen numerous posts of people successfully using this PS for this MB. I have tried reducing the power demand by switching to an old PCI video card, an old stick of 256MB memory, unplugging the optical drives, floppy and case fans, but the machine still shuts down just as quickly.
I finally got XP installed, but haven't been able to update the BIOS yet.
Is there anyway to know whether it's the CPU, the PS or something else causing the shut down?

MSI K8n Neo Platinum

Hi Guys,
I am having a problem with my computer at the moment. I am having trouble getting into the BIOS of this motherboard (MSI K8N Neo Platinum). When I try to get into BIOS, it goes into a black screen with a little line on top of it and its blinking. This has never happened before. Then when I shut off my computer since I couldn't get into the bios, I turned it back on and it goes on but nothing goes to screen or it wont boot up to startup screen. Then I turn it off, I reset the BIOS and turn it back on. Now it boots up to the startup screen, but when it says press del to get into bios, I pressed that and it happens again, it will not get into bios. When I do this over again by resetting the bios, this time without getting into BIOS, it goes on and boots up to Windows XP. I want to reformat my hard drive with a fresh copy of XP Pro, but I can't get into BIOS to do that. Can someone help me?

Same thing happened to me today. Thanks MSI for publishing a Betaversion of a BIOSupgrade on the Live update..
At first I figured that there must have been some fault during the BIOSflash so I downloaded the file again and repeated procedure. This time it worked like a charm and I could do all my BIOS-settings. The next restart the problem was back again though, and this time I had swapped the order for my SATA-drives to boot (to the way they should) but the system couldn't boot. So I couldn't enter neither the bios or Windows. Luckily you can shift the primary boot device by pressing F11 though, so I got out of the libido...
Now I've downloaded the old 1.9 Version instead and I sure as h*** won't do any more beta-testing for MSI by using the Live Update anymore!

MSI K8N NEO Platinum Edition memory question

Hi there,
I've currently got a MSI K8N NEO Platinum Edition (Nforce 3) motherboard and 2X 512 MB Corsair Value Select memory modules (both double sided) running at DDR 400 - this runs completely stable and has done for a number of months. I would like to increase my memory to 1.5 Gig but there seems to be a lot of issues?
I originally planned to buy an additional 512 Meg Corsair value select chip and place it in Bank 3 - is this acceptable?
I assue that i would have to drop the speed down to DDR 333 from 400, could anyone tell me how much of a difference this actually makes (when playing FPS games Doom3 etc..) ?
Any help would be greatly appreciated as i've been looking through both this forum and the Corsair one and i cant seem to find the answer.
thanks in advance !

Just note that there are combinations of two sticks that will also make the board run in DDR333 mode (see page 2-8 of the manual). For example, using two double-sided sticks in DIMM2 and DIMM3. I've actually managed to get it to work at DDR400 in those two slots, but it's not perfectly stable and overclocking diminishes drastically. Bottom line is the system will work fine when forced to DDR333...as long as you don't expect to overclock the RAM to any significant degree.

K8N NEO Platinum 4 Red LED at Startup

I installed a new MSI K8N Neo Platinum mainboard in my computer in December 2005, and my computer has been a pain ever since. My problem is 85% of the time when I turn the power on it just won't boot up, I get 4 Red LED lights. If I shut it off and on half a dozen to 20 times. During one of those times it will bootup normal and work great. Shutdowns are normal.
My Family hates this and won't use it. This computer has been nicknamed the MSI Little Witch. I have had it down to barebones out of case with just graphic card, 1 memory stick, IDE harddrive, keyboard and mouse, it will do same thing. I've unplugged and replugged everything countless times. It still does it. I have tried Maxtor, Samsung, and Western Digital hard drives with fresh install of Windows XP Pro, it still does same thing. I have alternated memory sticks, same thing. It will warm reboot as long as I don't powerdown, but if I shut the power off it will not reboot until it cools down about 20 minutes. Then I can go through the same startup problems as I normally have. I have not done any overclocking.
Anyone have a fix to this fustrating problem?

I have the same problem with my K8N Neo Platinum. Except mine seems to occur after the motherboard has not had power after sometime. For example, it happened every time I moved my computer when I moved into and out of my dorm room. I don't know if its the same "cooling down" time you're talking about, but what usually fixes it for me (at least temporarily) is killing the power to the machine while it is on. Regular soft resets won't work for many tries, but when the computer is on with all 4 red LEDs i'll flip the power switch on the power supply. That usually makes it work fine. Also another thing that seemed to intermittently trigger it is changes to the BIOS. A CMOS reset would not fix that either. I would have to flip the power switch and kill the power. Then after starting it
up again it would be okay. I have also tried multiple combinations of different cpus, memory sticks, and video cards. I also made sure there were no shorts to ground anywhere.
Also after a year of solid operation (with the exception of this problem) I started to get Machine Check Exception BSODs in XP. I think this was because of a possible bad stick of RAM, because that seemed to cause lockups in the way beginning of the Windows setup (where it is loading files such as Windows Executive, etc). When I removed it and put another stick in, the windows installation would go fine. But, that did not fix the issue with this motherboard.
I've had so many problems with the multiple K8N Neo Platinums I have purchased. This is absolutely ridiculous I'm extremely POed at MSI for the widespread K8N series problems. I am usually very tolerant to companies when they have problems with products because I understand that problems and glitches can easily occur in mass production and design. It is virtually impossible to make a "perfect" product from the start. But the lack of response and concern from MSI about this is ridiculous. MSI did make an excellent motherboard here--if you can get a working one.

Opinion of K8N Neo Platinum?

Similar Messages

Maybe you are looking for