Outbound call doesn't disconnect after call end

Have you ever seen something like it:
I make a call from my ip phone (3911 or 6921) to an external phone (ex: cell phone: 084645727) and the call works fine, but when cell phone turned off the call, on my ip phone the call still connected, ip phone show me on display that the call still active, the call is just disconnect when I put the phone onhook.
I use CUCMBE: 7.1.3(SU2)
Cisco 2821 : c2800nm-spservicesk9-mz.124-20.T4.bin
debug vpm signal
BHEGV1#R2 Got Event R2_ALERTING
*Nov 25 07:42:36: show voice call status
CallID     CID ccVdb      Port             DSP/Ch Called #   Codec    Dial-peers
0xD8803    20E8 0x48177B78 0/1/0:0.3        0/1:1 *2125463737 g711ulaw 7500/40
0xD8847    1C9D 0x48177B78 0/1/0:0.1        0/1:3   7434       g711ulaw 1/7500
0xD88B2    26E8 0x48177B78 0/1/0:0.28       0/1:5 *087068998 g711ulaw 7500/30
0xD88B6    27E8 0x48177B78 0/1/0:0.27       0/1:2 *084645727 g711ulaw 7500/30 (it is my call)
0xD88BD    1D22 0x48177B78 0/1/0:0.2        0/1:4   7491       None      1/7500
0xD88C0    28E8 0x48177B78 0/1/0:0.22       0/1:6 *084743874 g711ulaw 7500/30
After cell phone turned off the call, the debug vpm signal just show me it:
*Nov 25 07:42:50: htsp_process_event: [0/1/0:0(27), R2_Q421_OG_ANSWER, E_DSP_SIG_1100]
Does anybody could help me !
Regards.

Hi All
I had this issue with Oi and EBT, not sure if this is the same, but i had an issue where the Voice channel in clearfwd - I was facing the Bug CSCtd74470, there a workaround but the upgrade of the GW to Version 15 works properly, the output of the "sh vo po sum | include clearfwd" will confirm if this is your case.
Also in others situations I solved my issue applying the command timeouts call-disconect 3, under E1 Port
Please rate this post
Cheers
Bruno Rangel
"Se você quiser alguém em quem confiar, confie em si mesmo. Quem acredita sempre alcança"
Renato Russo

Similar Messages

Free jabber disconnect after call for 10-20 sec

I try to use Free Jabber call to my system via DNS SRV record. It can connect to system but It will disconnect after call for 10-20 sec.
All case which call via DNS SRV record, I checked and found
-The problem happen only call to TPS (via conductor).
-If call to endpoint, It's working fine.
-If call to MCU (registered with VCS), It's working fine.
I see log files which new INVITE is sent by TPS to VSC-Exp, VCS-Exp tries to send it out and then TCP connection fails.
2015-02-09T12:45:04+07:00 DC-VCSE tvcs: UTCTime="2015-02-09 05:45:04,239" Module="network.tcp" Level="ERROR": Src-ip="172.18.7.8" Src-port="25297" Dst-ip="199.19.190.28" Dst-port="5060" Detail="TCP Connection Failed"
2015-02-09T12:45:04+07:00 DC-VCSE tvcs: UTCTime="2015-02-09 05:45:04,240" Module="network.sip" Level="DEBUG": Action="Sent" Local-ip="172.18.8.8" Local-port="7001" Dst-ip="172.18.8.20" Dst-port="25008" Msg-Hash="5130918937689017019"
SIPMSG:
|SIP/2.0 408 Request Timeout

I try to use Free Jabber call to my system via DNS SRV record. It can connect to system but It will disconnect after call for 10-20 sec.
All case which call via DNS SRV record, I checked and found
-The problem happen only call to TPS (via conductor).
-If call to endpoint, It's working fine.
-If call to MCU (registered with VCS), It's working fine.
I see log files which new INVITE is sent by TPS to VSC-Exp, VCS-Exp tries to send it out and then TCP connection fails.
2015-02-09T12:45:04+07:00 DC-VCSE tvcs: UTCTime="2015-02-09 05:45:04,239" Module="network.tcp" Level="ERROR": Src-ip="172.18.7.8" Src-port="25297" Dst-ip="199.19.190.28" Dst-port="5060" Detail="TCP Connection Failed"
2015-02-09T12:45:04+07:00 DC-VCSE tvcs: UTCTime="2015-02-09 05:45:04,240" Module="network.sip" Level="DEBUG": Action="Sent" Local-ip="172.18.8.8" Local-port="7001" Dst-ip="172.18.8.20" Dst-port="25008" Msg-Hash="5130918937689017019"
SIPMSG:
|SIP/2.0 408 Request Timeout

Call FM destination often disconnected after calling failed

Dears,
when i call RFC registered in .net with sap connector, it is often disconnected auto. after calling failed.
then we should re-start RFC server in .NET, and the connection (RFC destination)will be ok then
what tools could i use to trace these and any advice ?
BR

Hi,
when i execute RFC with empty table parameters, it is ok.
But it give error 'data not received' when set some data in the table parameter and then the connection is shutdown.
ths for your tool .

Call is getting disconnect after 3 min when the caller is in queue

Hi,
I am using icm 7.0 with ip ivr 7.0. when all the agents are busy and caller is in queue,call is automatically getting disconnected after 3 min with the message " We are experiancing system problem and unable to process the call. please try again later" .
Icm and ivr script are attached
Regards,
Dinesh Joshi

Hi Chrish,
you are right. the timer was for 180 sec only. now things are working fine after increasing the timer.
Thanks a lot for your reply.
Regards,
Dinesh Joshi

Call tone goes on after call picked

Hi, I have a problem with my new iPhone 4s that just happen sometimes, when I'm calling and they pickup the call on the other side, I still hear ringing sound during a chat. On the Other side the person does not hear it, only me.
I already have tried reset iphone, but does not help. And call my network and they say that they never have ear no problem like that. The carrie is Vodafone PT
Can someone please help me? I´m new to iOS just bought my 1st iPhone 3 weeks ago and already got a bad experience with it.
thank you in advance

While you probably know this, it shouldn't be happening, however have you tried resetting the headset? You may have to check with the manufacturer to find out what the procedure is for that. I've got a BlueAnt in-ear device and I do not experience that behavior in my 5S, or 4S that I had before that.

Calling India will disconnect after one minute

dear Customer service,
when we are calling to india and it will disconnect call after 1 minute and then again we have to call
please solve this issue immediately and we cannot go like that.
awaiting your reply soon
This post was transferred from its previous location to create its own new topic here; its subject and/or title has been edited to differentiate the post from other inquiries and to reflect the post's content.

callfailure wrote:
but I am sorry to write the service is becoming worst.
Hello
We have answered this query many times. The problem has nothing to do with Skype or Microsoft. The local telco authorities in Saudi Arabia where you are located frequently disconnect outbound VoIP traffic to protect their own state run monopoly. Try accessing the internet via a VPN.
TIME ZONE - US EASTERN. LOCATION - PHILADELPHIA, PA, USA.
I recommend that you always run the latest Skype version: Windows & Mac
If my advice helped to fix your issue please mark it as a solution to help others.
Please note that I generally don't respond to unsolicited Private Messages. Thank you.

Form doesn't exists after calling driver program

Hi,
     I had created a invoice form, and i called through driver program in se38.After executing i m getting as 'Form doesn't exists'.
'zinvoice1'   is the name of the smartform.
Code as follows:
REPORT ZINVOICE1.
tables: kna1,vbrp,vbrk.
parameters: p_kunnr like vbrk-kunag,
            p_vbeln like vbrk-vbeln.
data : fm_name type rs38l_fnam.
data: t_vbrp like standard table of vbrp,
      t_vbrk like standard table of vbrk.
data: fs_kna1 type kna1,
      fs_vbrk like line of t_vbrk,
      fs_vbrp like line of t_vbrp.
start-of-selection.
select single * from kna1 into fs_kna1
       where kunnr eq p_kunnr.
select * from vbrk into table t_vbrk
        where kunag eq p_kunnr and vbeln eq p_vbeln.
select * from vbrp into table t_vbrp for all entries in t_vbrk
         where vbeln = t_vbrk-vbeln.
CALL FUNCTION 'SSF_FUNCTION_MODULE_NAME'
    EXPORTING
      FORMNAME                 = 'zinvoice1'
    VARIANT                  = ' '
    DIRECT_CALL              = ' '
   IMPORTING
     FM_NAME                  = fm_name
EXCEPTIONS
    NO_FORM                  = 1
    NO_FUNCTION_MODULE       = 2
    OTHERS                   = 3
IF SY-SUBRC <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
        WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
CALL FUNCTION '/1BCDWB/SF00000050'
EXPORTING
    ARCHIVE_INDEX              =
    ARCHIVE_INDEX_TAB          =
    ARCHIVE_PARAMETERS         =
    CONTROL_PARAMETERS         =
    MAIL_APPL_OBJ              =
    MAIL_RECIPIENT             =
    MAIL_SENDER                =
    OUTPUT_OPTIONS             =
    USER_SETTINGS              = 'X'
      IM_FS_KNA1                 = fs_kna1
      IM_T_VBRP                  = t_vbrp
IMPORTING
    DOCUMENT_OUTPUT_INFO       =
    JOB_OUTPUT_INFO            =
    JOB_OUTPUT_OPTIONS         =
    TABLES
      IM_T_VBRK                  = t_vbrk
EXCEPTIONS
    FORMATTING_ERROR           = 1
    INTERNAL_ERROR             = 2
    SEND_ERROR                 = 3
    USER_CANCELED              = 4
    OTHERS                     = 5
IF SY-SUBRC <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
        WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.

CALL FUNCTION 'SSF_FUNCTION_MODULE_NAME'
EXPORTING
FORMNAME = 'ZINVOICE1'
VARIANT = ' '
DIRECT_CALL = ' '
IMPORTING
FM_NAME = fm_name
EXCEPTIONS
NO_FORM = 1
NO_FUNCTION_MODULE = 2
OTHERS = 3
IF SY-SUBRC 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
CALL FUNCTION fm_name
EXPORTING
ARCHIVE_INDEX =
ARCHIVE_INDEX_TAB =
ARCHIVE_PARAMETERS =
CONTROL_PARAMETERS =
MAIL_APPL_OBJ =
MAIL_RECIPIENT =
MAIL_SENDER =
OUTPUT_OPTIONS =
USER_SETTINGS = 'X'
IM_FS_KNA1 = fs_kna1
IM_T_VBRP = t_vbrp
IMPORTING
DOCUMENT_OUTPUT_INFO =
JOB_OUTPUT_INFO =
JOB_OUTPUT_OPTIONS =
TABLES
IM_T_VBRK = t_vbrk
EXCEPTIONS
FORMATTING_ERROR = 1
INTERNAL_ERROR = 2
SEND_ERROR = 3
USER_CANCELED = 4
OTHERS = 5
IF SY-SUBRC 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.

My proximity sensor doesn't work after call waiting

My proximity sensor works fine during calls. Until someone calls in while I'm on the call. Whether I answer or not, when I pull it away from my face it activates the screen as it should, but it never turns it back off when I continue the conversation. This ONLY happens with call waiting. once i press on the home button and unlock the phone it works fine, knowing that i had a replacement for the phone for the same fault and now and i don't know what to do as my brother's phone is exactly the same however it works fine.
I have an iPhone 6 running 8.2

Try removing your case. If still an issue, take it in to Apple. You have a 1 year warranty.

Re: Calling India will disconnect after one minute

Dear Norman,
It is disappointing to know that you dont reply to such kind of question. I am paid customer to SKYPE and using it from the time when it was not of microsoft. We as customer thought that with microsft it will be better but I am sorry to write the service is becoming worst. I sent many mails to customer support but not got any reply from them.
I am a paid and regular customer of SKYPE but your service is getting weaker and weaker day by day.
I wish Microsoft to address such issue with some authentic reply.
Wish you best luck and good time.
Sirfraz

callfailure wrote:
but I am sorry to write the service is becoming worst.
Hello
We have answered this query many times. The problem has nothing to do with Skype or Microsoft. The local telco authorities in Saudi Arabia where you are located frequently disconnect outbound VoIP traffic to protect their own state run monopoly. Try accessing the internet via a VPN.
TIME ZONE - US EASTERN. LOCATION - PHILADELPHIA, PA, USA.
I recommend that you always run the latest Skype version: Windows & Mac
If my advice helped to fix your issue please mark it as a solution to help others.
Please note that I generally don't respond to unsolicited Private Messages. Thank you.

LV 5.1 program Exec.vi call doesn't function after LV 6 installed

My LV5.5.1 program runs Resman via the SysExec.vi and
worked until LV6i was installed concurrently on the same computer. Why did the LV5.1 Exec.vi function quit
working? If I just create a Vi that just executes a
SysExec.vi I get the same result.

Hello,
In order to help you with your question, it would be helpful if you could answer the following questions:
(1) Can you run any executable (which you have verified you can run from the command prompt on your computer), besides Resman, from your LabVIEW 5.1 System Exec.vi?
(2) Can you run Resman from the LabVIEW 6i System Exec.vi? If not, can you run any other executables?
(3) If Resman is the only executable which you can no longer run using the System Exec.vi, can you still run Resman outside of LabVIEW?
(4) What version of NI-VXI do you have installed on your computer? You can check this in Add or Remove Programs from your Windows Control Panel.
Your answers to these questions will help me answer your main question.
Regards,
Sonya W.
Applications Engineer
National Instruments

Does call forwarding work even after calling chang...

I have a skype US premium account, All calls initiated from US skype id and forwaded to India Mobile number, is it still going to work even after implemeting "Changes affecting calling to landlines and mobiles within India"

I have a skype US premium account, All calls initiated from US skype id and forwaded to India Mobile number, is it still going to work even after implemeting "Changes affecting calling to landlines and mobiles within India"

Dial-up for checking emails doesn't disconnect after checking

Hi, is there a way to ask the Treo to disconnect once it has dialed up to check for messages? I am getting a hefty data bill as it checks in the middle of the night and does not disconnect unless i ask it to.
Post relates to: Treo 700wx (Verizon)

Thanks. I ended up taking my PC to my daughter's - she's on high speed - and I downloaded the updated versions of everything I needed. My Dial-up is too slow (26.4 kbps YIKES!) to do that... bummer. So guess I'll just have to bring my PC to town periodically to do updates.

FP Read/fplvmgr.dll doesn't unload after execution ends.

I have an executable to run on the PC, accessing FP hardware as I/O. Some portion of the
executable is not unloading when execution finishes. A task is left running which must be
manually killed with the task manager. It seems to be related to the FP Read (might be
others as well) and might involve fplvmgr.dll which sometimes is locked (can't be deleted,
renamed, etc.). Any ideas on what is going on and how to get everything unloaded when
the program quits?
Thanks.
Matt
Message Edited by Matthew Williams on 11-30-2006 03:49 PM
Attachments:
test1.PNG ‏6 KB
test1.vi ‏31 KB

I am using LV 7.1.1, Fieldpoint 4.1, running the exe on the pc.
FPLVmgr.dll is 152KB (155,648 bytes), dated 05 April 2004, MAX 3.1.0.3021.
I have waited at least several minutes and the exe remains in the task manager,
consuming ~22MB of memory. I'll try waiting longer. Subsequent runs of the
exe leave additional copies in memory. Each copy also leaves an icon on the
task bar unless HideRootWindow is true in the ini.
I have tried the fp express vi with the same results.
Thanks for any ideas.
Matt

Video calling - PC to Android, call answers then disconnects?

PC video call to Android cell video, it works, but then I drive away from the location of the originating video call and Skype disconnects the call. I had created a second skype account in order to call it so I can check on my dog while I'm away. What's is wrong? Thx.

For anyone who has successfully received the platform exchange (windows to mac), how long did it take for adobe to complete the order, begininning from the date you requested the platform exchange to the date you actually received the software in the mail?
I'm currently in the midst of this process - I've contacted adobe and asked for the platform exchange, filled out the Letter of Destruction and uploaded it to adobe, then called adobe back to confirm they received the LOD, even paid the shipping charge.
All this took place a little over three weeks ago, and I still haven't received any word from adobe regarding my order. Every time I call, I get the same line: "I've put a rush order on your case, you will be receiving an email in 24-48 hours to confirm that your case has been processed and the software is being shipped." I've heard this same line 4 times now over the course of 3 weeks, and still have not received any email.
When I've asked to speak to a manager the last couple times, I get put on hold for 5-10 mins, then the call is disconnected.
Has anyone had this much difficulty with a simple platform-exchange?! I currently have CS4 web premium which I got as a gift, however it's for windows, and I have a mac.
Does adobe have the most horrendous customer service, or is my paperwork getting lost and I'm just unlucky?

HT204380 When I try to FaceTime my sister, she doesn't receive the call on her end, but if she facetimes me I always receive hers. Is this a problem on my end or hers?

When I try to FaceTime my sister, she doesn't receive the call on her end, but if she facetimes me I always receive hers. Is this a problem on my end or hers?

Have her check her "You can be received at ..." settings (Settings/ FaceTime) to see what she's set up as the points of contact to reach her via FaceTime (can be one or multiple e-mails or a phone number). Perhaps you're trying to FaceTime her on an e-mail or phone number which she's not using for FaceTime.

Outbound call doesn't disconnect after call end

Similar Messages

Maybe you are looking for