PAL/NTSC DVD's

I recently purchased a 17-inch Intel-based iMac, and i was wondering if it can play DVD's from different countries (Japan in particular), wouold there be a problem with PAL/NTSC TV's??
Thank You

Remember you will only be able to change the Region Code in your computer 5 times. After that it will be locked to the last Region Code you used.
So if you have DVD's from say Japan and the USA, then each has a different Region Code. If you play a USA, then a Japan DVD, that will use up one of your changes, then if you go back to USA then another will be used. Once you use the 5th change your machine will only play discs from the Region Code you last set it to. SO you could only play USA or Japan NOT both.
This has nothing to do with NTSC or PAL as they are not Region Code based.
They are simple the format of the TV signal being output.
If for instance you only ever use Japan DVD's all with the same Region Code then it does not matter if they are PAL or NTSC you can play them as many times as you like, no issue as you swap from one to the other.
Region Codes are there to prevent content from being bought in one region of the world and played in another.
You can read more about Region Codes here :-
http://en.wikipedia.org/wiki/DVDregioncode
Ian

Similar Messages

  • PAL & NTSC DVDs--an Option?

    I have an extensive collection of PAL & NTSC DVDs. The G5 has a (lower) empty optical drive slot. If I install another Superdrive will I be able to set it up to exclusively use this to play PAL regions 2 & 4 DVDs without locking the G5 permanently into this format i.e. use the first drive to still play NTSC Region 1 DVDs only? I understand that the manual says the the format choice can only be changed 5 times, but it is not clear to me if this statement applies only to the optical drives or the computer itself. I certainly do not want to make an irreversible choice for the G5!
    Any help will be appreciated.

    So... You are confusing video standard (format) with region codes here. The optical drives in Macs (most) are region code locked, meaning that they will only play disks from one region (and that region may be changed up to 5 times before the hardware gets stuck). It doesn't care what video format is on the disk from that region (NTSC or PAL), and it doesn't care about region-free disks (recordable DVDs, and commercial region-free disks).
    On the Mac, the region locking is managed by firmware on the drive itself, so you can have one drive per region, if you like.
    It might be more convenient to upgrade the firmware on the drive (depending on what model you have) to a region-free version of the firmware. As you may or may not be aware, the US is a WIPO signatory country and is prohibited from recognizing region codes as a form of copy protection or copyright control. Apple includes region code locks on their drives, ostensibly at the behest of their peers in the media industry, but it's perfectly OK for you to remove it (and, there are locales where region code locking is actually prohibited, but presumably if you bought your Mac there the locks are already absent). Be aware, however, that changing the firmware of the drive would void the warranty on the drive (not the whole Mac, just the DVD drive).
    Another option might be to purchase an external region-free DVD drive.

  • Possible to do a DL PAL / NTSC DVD?

    Hi,
    we just finishing our DVD which is a PAL project and just comes out to fit a single DVD. Is it possible to make a DualLayer DVD with a PAL project on the first half and a NTSC project on the second to increase the commercial sale possibilities for the USA and Japan? Would a standard DVD be able to choose between these two or does it has to work through a kind of universal Menue?
    Best regards - Christoph

    Christoph:
    Would a standard DVD be able to choose between these two or does it has to work through a kind of universal Menue?
    There is no way to include both standards PAL/NTSC material in the same disc/project.
      Alberto

  • PAL/NTSC DVD player question

    Greetings, Can I play a PAL format DVD from the UK in my Powerbook? Here is the info. from system profiler:
    MATSHITA DVD-R UJ-835E:
    Firmware Revision: GAN7
    Interconnect: ATAPI
    Burn Support: Yes (Apple Shipped/Supported)
    Cache: 2048 KB
    Reads DVD: Yes
    CD-Write: -R, -RW
    DVD-Write: -R, -RW, +R, +RW
    Burn Underrun Protection CD: Yes
    Burn Underrun Protection DVD: Yes
    Write Strategies: CD-TAO, CD-SAO, DVD-DAO
    Media: No
    I have read that if you play a PAL format DVD more than five time my settings will be permanently locked in the PAL format, and I will no longer be able to play commercial NTSC DVD's. Which would be bad. I do travel allot with the Powerbook and watch movies on the plane. Should I consider converting all PAL DVD's into NTSC? If anyone could shed light on this please advise. Thanks.

    Here's the work-around I use, which just requires that you have enough free space on your hard drive to hold the entire VIDEO_TS file (up to 8 GB): Download the freeware program Mac the Ripper (Google it, then find a site that MacroVision hasn't hacked into and shut down, and proceed with the download and installation). Insert the DVD you want to watch. The DVD player in your Mac will then ask you if you want to use one of your few remaining region switches. IGNORE that dialog box altogether--just leave it open without selecting anything (if you select CANCEL it'll eject your DVD, so don't do that).
    Open Mac the Ripper and following the clear instruction manual to set the controls properly copy the DVD into your Mac (I choose to save the file in the Movie folder). Takes about 20-25 minutes for most movies, and the copy you get is stripped of region coding. When that is done, close MTR, go back to the dialog box of your DVD player, hit CANCEL, and let the disk eject. Then reopen the DVD player, and have it open the VIDEO_TS file. Playback will proceed as if you were watching the DVD itself.
    PS-if you want to burn a DVD backup stripped of region coding, you can use DVD2oneX2, a file-compression/DVD burning program available for a free 30-day trial, $30 thereafter. Works very well. Good luck & (hopefully) enjoy!

  • PAL DV footage to NTSC DVD help wanted!

    Hi there, apologies if this has been tackled elsewhere, but I couldn't locate it!
    I have a finished PAL edit of around 90 minutes in FCP 4.5 that I have output to a PAL DVD via DVD SP 4/Compressor 2. Following this, the client has also asked for an identical NTSC DVD to send to the USA. Luckily I have the edit still loaded in FCP - therefore: This is the first time I have needed to do a standards conversion. Can anyone advise what the best method/workflow for creating this NTSC DVD is?
    Many thanks in advance for your time, TP
    PowerMac G5, Dual 1.8 ghz, 3GB Ram, 250 GB HD   Mac OS X (10.4.6)   FCP 4.5, DVD SP4, Motion, Toast 6 Titanium

    You didn't understand what my last post said.
    I said go from his PAL DV edit in FCP to a DV tape (DVCam preferrably). Then have the PAL DVCam tape transferred to another DVCam tape in NTSC.
    PAL is better quality that NTSC so there will be some loss just because there is less resolution in NTSC than PAL, but keeping it on a DVCam tape is fine.
    Then log the footage back into FCP with NTSC settings and then edit/export/author.
    I said nothing about tranferring it to analog or VHS. I don't know where you got that one. He said his original footage was edited in DV.
    And YES, if you take it to a "professional" dub house it will turn out better than most software conversions is what i meant. I have used Lightning Media in Hollywood for years and their stuff turns out great.

  • NTSC DVD doc for PAL Europe. Updated Advice on IF I need to convert & HOW?

    I have read with interests several posts on playing NTSC, all region DVDs on PAL DVD players. I hope someone may have some updated advice for my situation. In brief, I would like to give out DVD copies to festival goers in France where my Doc will play in April. I thought to produce DVD-Rs on my Mac.
    With a film acquired documentary(24fps), transferred to NTSC video (29.97 fps) sitting as both Avid and Final Cut Pro Media on my trusty G-4, I am now ready to export a Quicktime Movie and then encode to MPEG-2, and "author" a DVD in DVD Studio Pro.
    Will an NTSC DVD now play on most DVD players and Televisions in Europe? (A contact stated their "players are bi-standard NTSC and PAL", but I'm still uncertain this means my DVD-R or replicated NTSC will play).
    Should I make a PAL DVD?
    IF I try a PAL DVD is it really as simple as exporting a Same as Source Quick Time Movie from Avid or FCP then using the QT MPEG-2 exporter and selecting "PAL" from within Quick Time? Then I just create a new Pal project in DVD Studio Pro?...... Even if it is that simple to create PAL from QT and my media, I don't see how my 24 fps/29.97 fps doc now magically becomes PAL 25 fps / 59.97 fps just because I converted it to MPEG-2.
    Do you all recommend I try to make my own PAL DVD or should I just take my already authored NTSC DVDs and cross my fingers.
    I really appreciate any newer thoughts on this topic. I'm an old pre-digital film guy so be kind.
    Thanks, Rob
    G-4 Quicksilver   Mac OS X (10.3.9)  

    Yes, although the vast majority of newer European DVD players and TVs have no problems with NTSC DVDs, the only way to be sure (well, almost sure) is to burn a PAL DVD. You can't legislate for the fact, however, that not all DVD players can play all DVD-R authored disks, but that's a seperate problem!
    I generally use After Effects for quick and dirty (but good quality) standards conversion. Whatever you do don't just try exporting your project via Quicktime using a PAL as this will only change the colour space and not the frame rate or frame size. If you use QT to change frame rate it will simply repeat every fifth frame to get to 30fps which will give you jerky motion.
    Here's a step by step guide to doing the conversion in Compressor 2, using "optical flow" to interpolate to get the extra frames :
    http://www.macworld.com/2006/02/secrets/marchcreate/index.php?pf=1

  • Will PAL dvd player play my NTSC DVD-r?

    I'm trying to figure out if I need to convert several NTSC dvd's into PAL format to send to a friend's mom in Israel (she's very sick and would like to see these soon).
    Since I've never converted between these formats, I've been doing lots of research and keep getting more confused. I downloaded JES Deinterlacer (i think thats what its called) but I'm not sure I need it since I read the following on an imovie FAQ website:
    "I have an NTSC project and want a PAL DVD.
    The good news is: You can just send an NTSC disc. Any PAL set top DVD player capable of playing DVD-R discs can also play NTSC discs. All that is needed is a fairly new TV, built in the last 8-10 years or so."
    Could this be true? Can I really just send the NTSC dvd's to her? I hate to waste time here...please help...
    Thanks so much in advance.
    Jenny

    That´s right; NTSC DVDs will always work on PAL players when the player is compliant to the DVD specs. Those players do give out the regular NTSC signal and/or convert to PAL60. Some players can even convert to PAL50. The problem is the TV set.
    My German TV is 14 years old and cannot handle PAL60 or NTSC; I would need one of those rare players that convert to PAL50 (usually with poor results).
    But NTSC DVDs will always work on a PC (when it is an all-region DVD).

  • Switch NTSC DVD slideshow to PAL

    Good morning,
    my wife and I recently received a DVD Slideshow made on a PC in the NTSC format from our Wedding photographers.
    My family lives in Europe and cannot watch NTSC format. Is there a way to make a copy of my slideshow but in the PAL format?
    Thank you very very much.
    P

    Hi
    Usually - NTSC-DVDs plays well in PAL players - but not the other way around.
    So here is my notes on PAL to NTSC. Just think the other way around.
    PAL to NTSC or NTSC to PAL
    A. Copying commercial DVDs - No Not possibly at all - Not even legal to discuss.
    B. Home made DVDs (DVDs without copy protection)
    C. Movies from iMovie or FinalCut
    • Save as full quality QuickTime .mov and convert this with JES_Deinterlacer  (free on internet)
    NTSC ---> PAL.
    • Most often not necessary - Most stand alone PAL DVD-players playback NTSC
    (if TV is old in BL/W)
    PAL ---> NTSC.
    • If played on Mac - not necessary AT ALL
    • If on NTSC DVD-player - CONVERSION IS NEEDED - nearly no Stand alone NTSC-DVD-players
    playback PAL at all.
    To do this You need to convert the PAL DVD to streaming.DV or full quality QuickTime .mov
    • I use Roxio Toast™ to do this (There are no free converter)
    • JES_Deinterlacer  (free on internet) to convert to NTSC
    • Set up an NTSC project (29.97fps or 30) in iDVD and import then burn
    I burn to
    • Verbatim DVD-R
    • Set down burn speed in iDVD to x1 or x4 recommended by many
    • Secure a minimum of 25Gb free space on internal boot hard disk before burning (IMPORTANT)
    PAL is 25 fps and an analog TV standard of 625 lines
    NTSC is 29.97 fps and 520 lines
    NTSC (29.97fps) 520 lines - about 640x480 pixels (square) 720x480 rectangular (narrow) pixels
    PAL  (25 fps)   625   lines - about 768x576 pixels (square) 720x576 rectangular (narrow) pixels
    to use a photo 702x480 resp 576 then add 9 pixels on each side to add together as 720
    If iDVD hangs on PAL or NTSC.
    Bengt W wrote
    Deleting iDVD pref. file - should return You into NTSC mode.
    Yes iDVD can switch to PAL - BUT as You see with a rather lousy result.
    a. Need to convert to PAL - most often not - Most PAL-player can playback NTSC
    and on a fairly new TV in color. (old TV in Bl/W)
    (Other way around - from PAL to NTSC most often a must - few NTSC-player can use PAL)
    b. IF MUST - then use JES_Deinterlacer to do this conversion - so much better and free.
    My list on this (or rather PAL --> NTSC - just think the other way around)
    Allosaurus writes
    Thank you SDMacuser. I dumped all the plist icons with no result, and was getting pretty plist off when it occurred to me to delete all the previous dvd.proj files. Bingo. That did the trick. So thank you for all your help and the additional information you provided.
    Yours Bengt W

  • Producing NTSC dvd's from PAL projects

    Hi
    I'm in Australia (PAL) but would like to produce dvd's that can be viewed in the USA.
    If I produce a NTSC version of my PAL filmed project in idvd, will it work in NTSC dvd players in the USA?

    when you set iDVD to NTSC/29.97 and import a PAL iMovie, iDVD will convert your material and creates a NTSC videoDVD ...
    ... my experience, going vice versa, NTSC >>PAL, told me, that the underlying QTengine doesn't show a good result.. so, the long way for a probably better result is:
    export your iM as 'QT/Full Quality' ..
    download and use for free JES Deinterlacer
    open your iMexport, choose 'Project, conversion' and let JESDI do the conversion..
    drop THAT new file into a NTSC iDVD project..

  • Create a DVD playable on PAL & NTSC.

    Hi
    I am using Encore CS3 and would like (NEED) to create a DVD that will play on both PAL and NTSC DVD players. I have read in forums the following theory...
    Master my content at 23.976 and then import it into Encore. After output it will be interlaced by any DVD player to either 30 or 25 interlaced fps.
    When I try and import into Encore I am only given the option of PAL (25fps)or NTSC (29.97), so which do I choose and how can I be sure that My final DVD is in fact 23.976 fps and will play on any format?
    PS, This is all very new to me as I am a 2D illustrator by trade!
    Thanks in advance

    I live in London, UK and work for a TV company that produces shows for PBS
    in the US. I have never had any problems here playing NTSC discs.
    They do look a little softer than PAL ones, since the picture is stretched a
    little but not so the average user would notice. The only problem that might
    crop up is if someone is using such an old TV or monitor, and we are talking
    very old here, the picture could play in black and white.
    The reverse isn't true - we have had lots of issues with PAL discs being
    sent to US clients and being unplayable.
    I am sure you know this but just in case not there is one caveat... do not
    add any regional code! Almost every TV professional I've worked with still
    confuses regional codes, region 1 for US and region 2 for Europe with video
    formats NTSC and PAL. If you do add a region code then you will find discs
    will not play!
    Make your discs in NTSC and region free and you should be fine 99% of the
    time!

  • How to convert DVDs (PAL, NTSC) to mp4?

    Hello,
    I would like to convert DVDs (PAL, NTSC) to mp4.
    I have Adobe Premiere Pro CS3, but never used it.
    I am looking for a easy to understand information how to do it step by step.
    Maybe there are already how tos for this?
    PAL: 720 x 576, 25 fps
    NTSC: 720 x 480, 29 fps
    Thank you very much.
    Sandra

    Oh, you need to learn the program first before you can export anything...
    Get yourself a month of Lynda.com subscription and learn CS3.
    Watch the Online Video Course Premiere Pro CS3 Essential Training
    Adobe TV had a course for CS3 but they dropped that.

  • Same project in CS5 to PAL DVD and NTSC DVD.

    Hi everyone,
    I am trying to find best solution how to do it. My project is slideshow with scaled JPEG images and some video clips from DSLR camera Canon T3i.
    I know that video is 16:9 (1920x1080, 29.97fr) ratio and my output should be 4:3 ratio. With this I can deal with no problems, because is just few clips. My conclusion is: How to deal with PAL SD 4:3 ( 720x576, 25fr) ratio and NTSC SD 4:3 (720x480, 29.97fr) and a lot of images. What sequence settings I should use for the project? What I can think: start with DV PAL after everything is done put in DV NTSC sequence and scale it? Any other thoughts, please?
    Thank you, Art

    I was recently faced with a problem on an HD NTSC video that I videoed and produced.  The customer wanted a DVD that relatives over in Germany could view.  My concern was how to produce and test a PAL version.  My good friend Harm advised me that any DVD player in Pal-land has the capability of playing NTSC DVD video disks!   It worked fine.

  • PAL/NTSC conversion for DVDs

    Hello All
    I recently had some work involving standard conversion of DV PAL material and then burning said material onto DVD. Everybody trying it knows that this is time consuming and doesn't always produce the desired results - for obvious reasons (Methods used by me were the two documented on Dan Slagle's Unofficial iMovie FAQ).
    I then had the really "fantastic" idea to tweak the DVD with myDVDedit, by simply setting the IFO parameters to NTSC 720x480. Tested the burned DVD on two different set-top NTSC DVD players - and discarded the whole thing as "silly BS"
    Searching through the Net I just found out, that somebody had the same idea using IFOedit (the PC equivalent to myDVDedit) and that the results were mixed, but there were a lot of users that shouted: "great, this works".
    Getting a bit confused now, as i had thought this over after my own experiment and had come to the conclusion that it couldn't possibly work.
    Any insight would be greatly appreciated
    viva la mela

    Hi mish,
    that is such a .. <searching correct english word> hillarious (?) idea, I give you a star for that ;-)))
    changing some flags on a ready-made dvd... wow! nice try...- but as Fred said, NTSC<<>>PAL conversions are no trivial tasks... you run into many problems, e.g. where do you get the additonal 5 frames per second you need for a transfer from PAL to NTSC? how to make the audio fit to these new pictures? and, I HAVE to do this silly joke: NTSC has a very different color concept (Never The Same Color) then PAL.. and for sure a different res...
    the name is irritating, but all mighty JES Deinterlacer is doing a fantastic job in converting video standards (ok, for a free software solution...) give that a try!

  • PAL - NTSC  Prores for DVD authoring

    Hi
    Ive 100 mins of concert footage shot on Canon t2i. 25fps PROGRESSIVE.
    I need to author and duplicate a DVD using DVD studio pro, this will be pressed and released commercially.
    Im trying to get the best quality and work method.
    After loads of reading, so far, this is my work route.
    1. Convert Prores files from PAL - NTSC using Comp 4.
    Im keeping the same size, 1920 x 1080, just changing the frame rate to 29.97.
    In frame controls I have ..
    Resize - BETTER      Deinterlace BETTER ( though can this be set to FAST as the footage is PROGRESSIVE)
    Rate conversion BETTER
    2.Take these NTSC Pro res 1920 x 1080 and convert in COMP 4 to m2v. Using 2 pass VBR. (???????)
    It looks OK...just paranoid... just want to know if im missing a trick....????

    A couple of thoughts:
    If you're sending out this to a replication house, I'd  check with them before you do anything in Compressor or DVDSP to make sure you know all their specifications.
    Also consider sending your movie to a post house that has the hardware to do standards conversions. You can do it in Compressor (or another compression apps) but hardware doe a conversion better job than software,  Asj the replication people for their recommendation.
    What you outlined for steps in Compressor seem pretty reasonable. A few recommendations:
    For best quality, set the Resize  filter to Best. And Compressor will see that your video is progressive so that setting can just be the default.
    Yes. Use two pass VBR – unless the replication house says otherwise.  (Check with the replication people about optimal bit rate settings.)
    For Audio set Dialogue Normalization to -31.
    magenta1 wrote:
    It looks OK...just paranoid... just want to know if im missing a trick....????
    Not paranoid…just smart.
    Best of luck.
    Russ

  • HD 1080i PAL to DVD NTSC

    I've learned a tremendous amount from reading the forum, and this is the first time I've been compelled to post - I am stuck! 
    My basic question is what is the best way to go from 1920 x 1080i AVCHD 25 fps PAL source footage edited in its native format in Premiere CS4 to a SD NTSC DVD authored in Encore?  I'm fine with losing quality, but I've been getting choppy video in transitions and audio sync problems, and that's not acceptable.
    I've tried using the dynamic link and transcoding in Encore with all sorts of different settings and usually end up with the audio going out of sync in a couple spots and some unexpected frames in transitions that cause jumps.  The best I've come up with is encoding to NTSC 23.976 fps progressive, 2 pass VBR which still has slightly choppy zooms. 
    The sequence is about 27 minutes and takes 2 hours to transcode to NTSC 23.976 fps WITHOUT using the maximum quality option.  If I select maximum quality then it takes over 24 hours (!!) and the quality is actually worse (jumps in transitions and audio sync problems).  Could this be due to the "frame blending" bug that I've read about in AME?
    I realize I'm dealing with two major issues: frame rate and resolution.  Any suggestions?  Thanks.
    - Aaron
    System Info:
    AMD Athlon II X4 2.9 GHz
    8 GB RAM
    64-bit Windows 7
    CS4 Production Premium
    Drives:
    C: System
    D: Pagefile/Project Files/Media Cache
    E: Source media

    Thanks for the quick replies, everyone.  It seems that there were some specific edits that were causing audio syncing and video glitches - they were fine in the Premiere project, but would cause problems when exported.  I spent some time exporting (directly from Premiere without multiplexing or changing the frame rate) those specific sections that were giving me problems.  I couldn't get anything to work consistently.  Finally, out of desperation, I tried exporting to tape and it worked!  It rendered to 1080 50i HDV and recorded to my Sony HDR-HC9 without any problems.  Then I recaptured it into Premiere and was able to export it from Premiere into both PAL and NTSC standard definition Encore projects without any problems.  I think it must have been some problem with way Premiere was trying to export the original AVCHD clips and/or the way they were edited together.  I'm not really sure what it was, but I'm relieved it finally worked. 
    - Aaron

Maybe you are looking for