Portege Z930 - USB3.0 works as USB 2.0 after Win 7 installation

Hi everybody,
After deinstallation Win8 and installation of Win 7 (all drivers downloaded from this site) USB3.0 work as USB2.0 (speed).
And I see 1 unknown device in the Device Manager such as USB controller.
Install driver some times but without results.
What this can be?

Hi
You could install the USB 3.0 driver
[USB 3.0 driver|http://www.toshiba.co.uk/innovation/download_driver_details.jsp?service=UK&selCategory =2&selFamily=4&selSeries=362&selProduct=7566&selSh ortMod=3582&language=13&selOS=30&selType=all&yearu pload=&monthupload=&dayupload=&useDate=null&mode=a llMachines&search=&action=search&macId=&country=8& selectedLanguage=13&type=all&page=4&ID=82919&OSID= 30&driverLanguage=42]
At the other hand I recommend checking the VEN ID and DEV ID of this unknown device to get some more details about this missing driver.
Instruction can be found here:
http://forums.computers.toshiba-europe.com/forums/ann.jspa?annID=78

Similar Messages

Can't Create USB Recovery Drive after Win 8.1 upgrade on Lenovo Twist

After upgrading to Win 8.1 and trying to create the usb recovery drive, I get this error:
"We can't create a reccovery drive on this PC. Some required files are missing.To trouble shoot problems when your PC starts,use your window installation disk or media"
Can some give me a hint as to how to solve this?Thx.
Solved!
Go to Solution.

I contacted Lenovo who sent me out a set of 4 Recovery disks. These disks fixed the problem but it meant wiping out the hard drive and reinstalling very thing from scratch. A new recovery partition is created and the discs reinstalled Win 8 which had to be updated. Then Win 8.1 could be installed. Everything is now working as it should.

Tecra M10-10z - 3G does not work after Win 7 installation

Tecra M10-10z I have installed Windows 7 pro 64bit
Everything is configured correctly, but connection 3G does not work: the message is " no network"
with Windows XP is ok.
I did not find firmware updates or similar.
Is there someone who can help me?
tks

Hi
In order to use the 3G you should firstly check if the 3G ericsson module was properly installed.
In case there is an yellow exclamation mark visible in the device manager, the 3G driver should be reinstalled.
I found on the Toshiba EU driver page:
[Ericsson 3G Win 7 driver|http://www.toshiba.eu/innovation/download_driver_details.jsp?service=EU&selCategory =2&selFamily=5&selSeries=148&selProduct=813&selSho rtMod=null&language=13&selOS=30&selType=295&yearup load=&monthupload=&dayupload=&useDate=null&mode=al lMachines&search=&action=search&macId=&country=all &selectedLanguage=13&type=295&page=1&ID=71930&OSID =-1&driverLanguage=42]
Furthermore ensure that the 3G RF Power Control Utility has been installed properly.
The 3G RF Power Control Utility" activates your 3G on startup.
This tool can be found here:
[3G RF Power Control Utility for Win 7 64bit|http://www.toshiba.eu/innovation/download_driver_details.jsp?service=EU&selCategory =2&selFamily=5&selSeries=148&selProduct=813&selSho rtMod=null&language=13&selOS=30&selType=322&yearup load=&monthupload=&dayupload=&useDate=null&mode=al lMachines&search=&action=search&macId=&country=all &selectedLanguage=13&type=322&page=1&ID=73658&OSID =-1&driverLanguage=42]
Hope the 3G network would functions after the reinstallation of both tools.

Tecra S3 - Wlan does not work after Win XP installation

Hello everyone,
I have recently purchased a Tecra S3 PTS30E-0TL059GH without operating system.
I've installed WIndows XP professional.
Everything works, except for the wireless lan. I can switch it on, but it doesn't seem to find the right drivers.
The device manager states problems with the networkcontroller and two other unknown devices.
I've installed all drivers from the toshiba website, but it still won't work.
Any help is appreciated!
Thanks!

Hi
I think the notebook supports INTEL 802.11 B/G WLan card but I'm not 100% sure about that...
In my opinion you should try to identify the WLan module.
How to do that?
In such case the usage of the PCI database should be very helpful.
More details here:
[How to identify an unknown device (e.g. Wireless LAN module)?|http://forums.computers.toshiba-europe.com/forums/ann.jspa?annID=78]
Knowing the exact WLan specs, it should not be a big deal to get the right driver.

Working in Debug mode, not after building the installation.

Hi,
I have a button to launch a form.
When I test it in debug mode, it works fine.
But, after making installation, if I do the same thing (press the button), I'm getting the following error:
Unexpected end of file while parsing name has occured. Line 1, position 2654.
Also, we have few add-ons operating on sales order.
When we open the sales order in client site through RDP, there is continuous flickering/refresh.
In in-house, we don't get that problem.
Please help me with this.
These are very critical issues for my release.
Thank you in advance.
Regards,
Geetha

Hi Geetha,
1.) button problem:
i don't know how you open the form - when you do it with a XML file maybe you packed the wrong XML file into your addon installer.
2.) the flickering can be a problem of formatted searches or interacting with other addons.
when addon a. changes a field it can be that addon b. does something because of the event from addon a.
the same can happen when you have formatted searches that do something when a field changes.
ok - that are my last tipps for this day
good night
David

SD card reader doesn't work on Satellite C850-1CN after Win 8.1 install

Hi,
Since I installed Windows 8.1 on my computer Satellite C850-1CN ref. : PSKCAE my SD port does not work
I would like to know if there is a driver I need to download because I searched the site for a pilot port but in vain ...
Sorry for my English I speak French and I hope I'm in the right forum

Hi
You have to download and install the card reader controller driver for Win 8.1 system
This driver should be the right one:
[Card Reader Controller v 6.1.8400.30136 Windows 8.1 - 64 Bit|http://www.toshiba.eu/innovation/download_driver_details.jsp?service=EU&selCategory =2&selFamily=2&selSeries=312&selProduct=7499&selSh ortMod=3417&language=13&selOS=all&selType=316&year upload=&monthupload=&dayupload=&useDate=null&mode= allMachines&search=&action=search&macId=&country=a ll&selectedLanguage=13&type=316&page=1&ID=88526&OS ID=46&driverLanguage=42]

Satellite L305D-S5881: Touchpad and FN keys do not work after Win 7 installation

I have recently installed windows 7 and all of a sudden yesterday my touchpad did not work.
I was not able to move my mouse arrow at all.
I had to purchase a wireless mouse so I could use my laptop.
When I press the fn key plus f9 nothing happens to see if it is enabled or disabled.
I have a satellite l305d-s5881
thanks for your help

Hi mate
The Satellite L305D-S5881 belongs to the Toshiba US series and has been released for US market.
You will need to visit the Toshiba US driver page in order to get all drivers.
To get the touchpad working, you will need to install the Touchpad driver.
Furthermore the FN buttons are controlled by VAP (value added package) and Flash Card Support Utility.
You need to install both; firstly VAP and then Flash Cards.
Here is the Toshiba US page:
http://www.csd.toshiba.com/cgi-bin/tais/support/jsp/home.jsp
Greets

Satellite C55t-A5123 No working web cam and microphone after windows 10 installation

I updated to windows 10, so my pc camera and microphone have not worked since that. I want to know if there is any driver to download or something. Its urgent, please

Have you installed all the updates from Service Station and Windows Update?

Re: Satellite A200 Touchpad scroll dosnt work after Win 7 installation

When I change my windows from xp to w 7 my scroll dosen t work.
What should I do?
Sorry for my english....

Hello
The BIOS downloads you can find on the same place as drivers:
http://eu.computers.toshiba-europe.com > Support & Downloads > Download Drivers
Before you start the update, close all running programs and make sure that you are logged in as administrator.
Greets

Portege Z930 - Display Driver doesn't work correctly

Hello,
we have a Portege Z930 with Windows 7 64 bit in use where the Intel Display Driver seem to work incorrectly.
First problem is the slow presentation on display - if we open a picture (simple JPG) and move the window, the window frame will break during the move and be shown very bizarre.
Next we installed a dynadock U3.0 docking station for using two external displays additionally. This works even worse. For the docking station we used the driver from the CD included on delivery, and we connect it over an USB 3.0 slot.
On booting switching onto the 2 displays instead of the internal notebook display doesn't work - so we use the workaround of using an extended desktop over all 3 displays (2 externals and the internal notebook display as third).
In Internet Explorer we had to switch off GPU Rendering and use Software Rendering instead because otherwise we observed critical misfunctions on the external displays (having 2 windows open the display froze or couldn't show moving windows). Nevertheless the display is not satisfactioning.
We already tried 3 different versions of the recommendet Intel Driver which is also offered by Toshiba for download; we loaded it there and also 2 more versions (one newer, one older) from Intel directly.
So how can we get that working correctly?
Thanks in advance and regards,
N. Cochems

Most importantly. make sure you have Win7 Service Pack 1 installed. New notebooks have problems running in win7 RTM (no service packs).
Sounds like Windows is using the standard VGA driver instead of the Intel driver. Uninstall all the display drivers from Control Panel->Programs and Features then go to the Toshiba website and install the Intel Chipset Utility then the Intel Display Driver, then go to DisplayLink.com and install the latest DisplayLink driver for the dynadock. The new DisplayLink v7.xx driver fixes many problems found in the v6.xx drivers.
Double check that the Intel drivers are installed correctly in Device Manager.

Portege P4000: Cant recognize the external USB CD-ROM

Hi,
I have a big problem.
I have a Portege P4000 the DVD is broke but I have an external CD-Rom with USB. I want to replace windows 2000 on the notebook but it didn't read the USB port. I update the BIOS but I can use USB ports only with floppy disk. How I can to replace operative system inside the HDD??
Thank you

Hi,
To install an operating system on the 4000 you will either have to replace the broken drive or use a PCMCIA external drive.
It will not work from USB.
regards,
Nick

Portege Z930: Loss of Fn keys after Win 8 upgrade - cannot turn WiFi on/off

After many months biding my time I have just embarked upon upgrading my Portege Z930-11G to Windows 8 Pro.
Largely this has gone to plan with the exception that after running the Toshiba Upgrade Assistant I've lost the Fn key display and about half the keys no longer seem to function at all.
The only key I ever used routinely is the Fn+F8 option to turn WiFi on/off.
So now I cannot enable the WiFi on the machine.
There must, surely, be a mean to do this but I can't find it. Does anyone have a suggestion? I'm OK for now as I have a wired LAN in the house but once I get out on the road I'm going to struggle without WiFi.
Before running the upgrade assistant the Fn key brought the key display up across the top of the screen and I surely wish I'd turned WiFi on at that point.
The Fn key utility offers very little control of the Fn keys. It does not offer the ability to do anything other than disable five on screen notifications for keyboard backlight, power plan, touch pad, cursor overlay and numeric overlay.
All help gratefully received.
Andrew

> So now I cannot enable the WiFi on the machine.
First of all you can enable and disable the WiFi using function key but you can also enable the WLan in Windows 8 settings
Win key + C -> Settings -> Change PC settings -> Wireless
Now you can use the wireless devices slider to enable or disable the WLan.
But to get the FN key working you have to install the +Toshiba Function Key Utility+ for Win 8 and +Toshiba System Driver+ for Win 8

Choppy, distorted audio on Portege Z930 after updating from Win7 to Win8 64

Just wanted to share an info with you which cost me some time to work out, regarding the audio playback on a Portege Z930.
When I got my brand new Z930-14L, it was running Win7.
I tested everything like you do when you get a new machine and it all worked fine - including audio playback.
When I updated to Win8-64 from the CDs that came with the computer, still everything seemed to work fine and I had not changed any driver or setup.
However, after a couple of minutes, the audio playback detoriated. It got choppy, distorted, interrupted, stuttering and I was shocked.
Funnily, as soon as I turned my attention to the computer again, playback was OK again - though no screensaver had come up and no power save mode came up in such short time. I knew it was no hardware issue (because it worked under Win7), it was not a driver issue (because the first 5 minutes the sound was immaculate), it was not a ground loop (as many have suggested) because that sounds differently.
Thanks to another forum, I found out that it is actually the combination of Windows Defender, Win8-64 Pro and the audio driver that causes this. If the device is idle for some minutes, Defender thinks its a good idea to use the idle time to scan the SSD drive - causing inteference with the audio playback. Of course, you cannot simply disable or switch off the central antivirus process, which would kinda ruin the whole point. :-)
_So I installed Kaspersky suite on the machine (which automatically disables the Windows Defender) and the issue was gone!_ This is probably the only time that installing an antivirus suite FIXES an issue. :-)
BTW, this is probably not limited to this particular antivirus product, just play a bit with Defender.
Best, Yuppie

>So I installed Kaspersky suite on the machine (which automatically disables the Windows Defender) and the issue was gone! This is probably the only time that installing an antivirus suite FIXES an issue.
Thank you very much for sharing this details here in the community.
I guess information could be useful for others who have such similar sound problems.

Portege Z930: How to create GPRS / Wifi / LAN connection profiles?

Hi !
I can't find any software (Toshiba or Intel) on my Portege Z930 that can manage
connections profiles to automatically be connected on GPRS or Wifi or LAN regardless to connections available (office, home, public area...)
Toshiba Wirelss manager runs with GPRS only and not wifi or lan
Thanks for your help !
Best Regards

Hi
Such universal utility is not known to me.
The Toshiba Wireless manager handles the 3G profiles.
For Wlan connectivity and profile management you could use the TOSHIBA Configfree
Here a short details:
http://forums.toshiba.com/t5/General-Features-Knowledge-Base/TOSHIBA-Configfree-Utilities/ta-p/347098
Well, and LAN would works until the LAN cable is connected :)

Satellite M50D-A : USB 3.0 devices not working in USB 3.0 ports

I can use 2.0 devices in the 3.0 ports fine, but my 3.0 device Flash Voyager USB3 8GB will not work. It connects then disconnects once, not showing up in device manager at all.
I've tried installing the USB driver off this site version 2.0.10.273-130101a for my model. That made no difference.
Install system Windows 8.1
Any ideas? Thanks.

The Voyager USB stick is manufactured by Corsair
I found in Corsair forum some threads and complaints about the troubles connecting the Voyager USB3.0 stick to USB 3.0 ports. Here the link the Corsair threads:
http://forum.corsair.com/v3/showthread.php?t=115891
http://forum.corsair.com/v3/showthread.php?t=111945
It looks like there are some compatibility problems between the USB controller (from AMD but _not_ Intel) and this USB stick.
One of the solutions could be the usage of other USB 3.0 flash memory sticks which are supported by AMD chipset.
You could also try to update the driver manually. You will need to check firstly the chipsets specs and name. To do that, I recommend you to install some kind of hardware diagnostic software (Everest Home Edit or Sandra Sisoft).
Then you could check on AMD page if an update for this chipset is available.

Portege Z930 - USB3.0 works as USB 2.0 after Win 7 installation

Similar Messages

Maybe you are looking for