Powerbook Lower Memory Slot Issue, what are my options?

Hi there,
I have a Powerbook G4 1.5ghz that I purchased in October of 2004. I had no problems with it until after upgrading the RAM to 2 x 512mb chips and then installing Tiger which resulted in me later notcing the missing RAM and learning about the lower memory slot failure issue.
I find that sometimes if I remove the RAM and try and power it up and then replace the RAM again that the lower slot ocassionaly does come back. Trouble is though that the machine will either crash or I loose the other RAM slot when I have to shut it down. It seems to be so intermittent this way and I'm tired of constantly removing the RAM to fiddle about with it.
My serial number begins W8441, so it isn't covered by the returns programe. I would call Apple Support, but I am put off by a £35 charge just to have them discuss and diagnose the problem.
I'm in the UK and as I don't have Applecare and I'm not elgiable for the returns programe can anyone tell me what they charge for a logic board replacment? Looking at what they charge in the US, it's not cheap.
I use my Powebook for Final Cut Pro, DVD Studio Pro, After Effects mainly and I had been alright with 1gig when it was working.
I'm really trying to decide what the best thing to do is....
- Do I pay for the logic board replacement, which I'm not really sure I can afford right now, or to be without my machine... especially as I have read that it can just fail again.
- Should I just buy a 1gig stick for the upper slot and try and sell my old RAM, as that would be cheaper than getting the logic board replaced?
It's a real shame that Apple doesn't seem to want to ackowledge that this effects other users as I'd been so impressed with everything about Apple up until now.
Thanks for any advice.

(Browse down for findings and questions).
The notorious lower-memory-slot-bug has hit my finally too... I never believed it until now (and I've immediately signed the petition).
I am outside warranty and I never bought Applecare either.
Also my powerbook, a very dear machine to me, is a less common type to have this problem: a 1 GHz G4 15" FireWire 800 OS 10.3.9 type. Funny enough my older powerbook ( a G3 Bronze) is still running strong with no problems whatsoever.
My G4 15" also has the "white spots" problem and a dead superdrive... I cannot believe how many hardware problems I'm having with this machine in comparison to all my older macs - even my sluggish powerMac 7200/90 never gave me this many headaches...
Alright, I'll stop complaining for now.
I've been able to browse the internet on this and found the following statements:
The lower memory slot gets "fried" because of a OS 10.3.9 upgrade,
or possibly due to overheating when the powerbook is put on the users' lap,
or possibly due to picking the powerbook up by the corners so the metal gets bent.
+ I have only seen one case where someone's UPPER memory slot was defective.
The solution to this problem (replacing the logic board) didn't seem to be definate in many cases so I'm reluctant to try this myself (and I have very little money). The alternative (replacing the upper slot memory with a bigger type of RAM) seems a bit scary to me,
because I wonder:
-will the upper memory slot RAM get "fried" eventually as well after a while?
-do you need to have something installed in the lower slot or is it possible to just install one RAM card only?
-are there more people with a 1 GHz PB that have this problem? It seems it's mostly people with a 1,67 GHz that have been bitten by this bug and maybe that's why Apple decided to give the majority a free repair. I am not sure whether that is a common policy, I am part of the minority it seems.
As a solutions someone posted on a board that we should all buy KTA-PBG4333/1G RAM, but here in Dutch stores it is said this memory is only compatible with 17" powerbooks....
Does anyone know if it is suitable for 15" as well??
G4 Powerbook   Mac OS X (10.3.9)   1 GHz G4 Powerbook FW800

Similar Messages

  • "Your Time Capsule Disk is Low on Storage Space" What are my options?

    Hi I just got a message from Airport Utility that my Time Capsule is low on Disk space. My 500 GB Time Capsule only has 25GB of space left. What do I do? Do I have to purchase a 1GB Time Capsule. Can I simply replace my 500 GB Time Capsule with a 1GB Time Capsule. Will the new Time Capsule remember all my network and computer settings? Thanks

    Welcome to the discussions!
    You didn't mention if you were using Time Machine for your backups to your Time Capsule, but I will assume that you are.
    Some users reason that they don't need all the backups from many months ago and elect to erase the TC and start over with a complete backup. The risk here is that you have no backup until the new full backup is completed.
    And, if you have transferred files from your computer to the TC and then deleted the files on your computer, you lose those files if the TC is erased.
    In theory, you don't need to do anything as Time Machine will simply start to delete the oldest versions of backups to make room for new backups. My 500 GB TC ran out of space a few months ago. I used to be able to see how my computer looked a year ago. Now, I can see how how it looked about 11 months ago.
    If you want to preserve every backup since day one, then you will need to add more storage space. If you purchase a new Time Capsule, Time Machine backups will continue on the new machine.
    If you get a new Time Capsule, there would be very little configuration required. Basically, the new device would be setup as a bridge to the old Time Capsule using a short ethernet cable. You would need to reset Time Machine by pointing it at the new Time Capsule for backups.

  • How to repair lower memory slot ?

    Hello,
    I was the happy owner of a 15" PowerBook G4 until the lower memory slot died. The slot is said to be empty in system profiler (I've tried with different RAMs), but I still get the informations about the RAM in the lower slot when I boot on the hardware test DVD, althought it's written in red. I've already tried cleaning up the slot, reseting the NVRAM, the PMU and reinstalling an OS with no effect. My computer is out of warranty, (and the problem is not recognized by Apple on the 1.25 model - that doesn't mean I won't buy another mac, but I won't give them more money because they screwed it up !), but I need it to work as long as possible (waiting for 64 bits Macbooks ...).
    I have all the tools needed to open the computer, resolder some components if needed, or change them.
    What can I do to repair it ? What is damaged ?
    Thanks for your time,
    Jeremy

    I would still contact Apple as they have acknowledged this as a fault haven't they on other models? And if a free fix is up for grabs I would grab it myself. So do contact Apple and see what they say, if you haven't already.
    As regards soldering, the circuit boards would probably have been soldered using the flow solder technique. Basically they are dipped into a bath of solder I believe which is a simplified explenation.
    You will probably need a very fine soldering point to your soldering iron and some means to 'suck' the old solder out first before applying new solder to do the job properly. There will be a lot of pins to solder, I hope you have a big magnifying glass and a very steady hand. Remember don't try and solder too many in one go as the heat will build up in the board, so do a few and let it cool down in between.
    Good Luck if you do try to solder them.
    Phil

  • I'm so screwed....What are my options?

    My iPhone fell out of my pocket tonight and almost completely flushed down the toilet....I got it out and now it's buried inside a bowl of rice inside a ziploc baggie BUT....
    There are no other phones available right now. It's only been a few hours but I feel sooo lost without it. Its my alarm clock, I listen to it to fall asleep at night, and actually...I'm on vacation and I'm now without my contacts or anything.
    What are my options? I'm not a rule breaker so I don't want to get a unlocked one...too scared of "the man". LOL
    Any other ideas out there?
    WWYD?

    Is there an AT&T store around? AT&T will sell you a new, standard, bottom of the barrel cell phone for $40.00 that you can return for a full refund within 30 days (plus, there's no activation fee). Apparently, AT&T has a plan in place for those that are without a cell phone b/c of repair issues. I'd just let them know that Apple is currently fixing your iPhone and that they're out of stock and could not give you a loaner iPhone while yours is being repaired. It's worth a shot. Plus, if you're a good customer (been with them for a while, always pay your bill on time, etc.), they should help you out... Hope this helps .

  • My ipod nano 6th gen fell out of my pockey and the screen cracked badly, is there any coverage for this under warranty? I just bought it a month ago. If not what are the options for getting it fixed

    My ipod nano 6th gen fell out of my pocket and the screen cracked badly, is there any coverage for this under warranty? I just bought it a month ago. If not what are the options for getting it fixed? It is pretty frustrating, it fell from about 3 feet out of my pocket and now looks like it was beaten by a hammer.

    Debbie:
    deborahfromwindsor wrote:
    he advises restarting by inserting the OSX disc and pressing down the C button to reboot from there then selecting disk utility, hard disk and repair.... Does he mean me to hold down the C key on the alpha keyboard or the ctrl key?
    Should I just ask for my money back??? If it is a simple repair do I just literally push the disc in, push the power button and hold down the C button?
    That's where I would begin, too, with
    Repair Disk
    Insert Installer disk and Restart, holding down the "C" key until grey Apple appears.
    Go to Installer menu (Panther and earlier) or Utilities menu (Tiger) and launch Disk Utility.
    Select your HDD (manufacturer ID) in the left panel.
    Select First Aid in the Main panel.
    (Check S.M.A.R.TStatus of HDD at the bottom of right panel, and report if it saysanything but Verified)
    Click Repair Disk on the bottom right.
    If DU reports disk does not need repairs quit DU and restart.
    If DU reports errors Repair again and again until DU reports disk is repaired.
    If DU reports errors it cannot repair you will need touse autility like TechTool Pro,Drive Geniusor DiskWarrior
    First we need to determine if the issue you are experiencing with the computer is software or hardware based. Once we have gotten things sorted out there should be time enough to make you decision about keeping or returning it.
    cornelius

  • Buying New Phone but Contract  can't yet what are my options???

    Okay I dropped my phone in some water and had to find a replacement it is a razor but being it was given to me there are issues with it... The phone changes settings on its own and I can't access VM called Verizon and they can't help with changing it and the one that is in the phone is unknown. Talke with Verizon and then Tech Support and they did nothing and said they have no way to know what it is did a master reset and so on.
    So here is my question being the contract the phone is under does not allow new phones till December and I can't extend the contract being it is a business phone what are my options? From what I learned buying just a phone from Verizon is a costly one, and if you buy one from an online source the two I got where prepay only and not able to be used on an existing contract.
    If I take my replacement used phone to a Verizon Store can they get the Pin number out of? I know they are there to sell you a new phone and want you to extend your contract . The cost of a "NEW" Phone is in the hundereds of dollars when you get it for next to nothing when you sign a contract.
    Is there any good place I can get a "New Phone and reactivate it as a replacement and know what the pins are being the one I have now though used Verizon can't not hop[ena dn since it turns off the ringer now and then I miss calls and get vms I can get.
    Any suggestions or just go and buy a new phone whatever the best cost is and be done with this???
    ANy information on what I can do seems that Verzion can only help so far via the phone and going to a store from what I have experienced and heard is requiring an contract extension and then you get a new phone for a better price. Which again I can not do.
    Just looking for some good information on wat the options are???
    MikeMich

    Thanks, Looks like I am stuck with the current phone even though no one at Verizon can assist me in getting the pin for the vm feature. As for ebay I contacted 2 sellers that stated their phones were good to be used on Contract the first one I got I called attempted to activate it and they told me it could only be used as a "PrePaid" Phone. I had to return it and the seller want me to end the transaction as if his listing was valid even though it stated could be used on a existing contract. Being he was also in Michigan I got it within a few days but then had to return it. Seems many list their phones like this but when you contact them and ask they kind of side step it and the auction ends. This seller had good feedback maybe because some don't leave any because of the same issue. I looked at whast the phones are listed at an 300 + unless you sign an additional  2 years which I can't do being it is a company phone and paying twice is also not worth it using it as a prepaid phone for 6 months...
    Looks like they got you anyway so I will just have to continue getting vms and no access and hope the phone lasts until they can get new ones...
    Sad fact is there should be a better way to get a replacement phone. Since I don't know any Verizon Dealers when I had another carrier the guy was great he would do anything including rebuild a doa phone with parts he collected as people upgrade but at Verizon they just want you to "upgrade" and "extend" the contract Which I am not the admin person to make that decision
    Guess you have to know someone and I don't...
    Such is life these days...At least for me....
    MikeMich

  • I am making multiple DVD's of roughly 50 hours of footage on DVD Studio pro with 4 separate menus for 4 different 'parts' or series if you will. 50 hours - 20 episodes - 4 parts of 5 episodes each. What are my options in terms of burning these parts on to

    I am making multiple DVD's of roughly 50 hours of footage on DVD Studio pro with 4 separate menus for 4 different 'parts' or series if you will. 50 hours - 20 episodes - 4 parts of 5 episodes each. What are my options in terms of burning these parts on to separate DVD's, what is the process, what size DVD RW should I buy, what bitrate should I use, and what quality I should expect for the burn. Any advice or insight is welcome.

    >>What are my options in terms of burning these parts on to separate DVD's<<
    20 episodes totaling 50 hours equals about 2.5 hours per episode assuming all episodes have the same duration.  Fitting 2.5 hours onto one single layer DVD would require a low bit rate which means quality wouldn't be anywhere near best, but that's a judgement call you'll have to make based on several factors.  For example; if there is not much motion in the video (talking heads, etc), you can get by with a lower bit rate and may not notice any quality difference.
    >>what is the process>>
    The process is essentially the same as it is when authoring a regular DVD with 2 hours or less of content.  However, with as many discs as you'd need to complete this "set," you'll need to create a separate DVD Studio Project for each disc.  Basically, you'd use one of Compressor's DVD Presets (or customize a preset) to create an MPEG--2 video file (.m2v) and a Dolby Digital audio file (.AC3).  Import both of those assets into your DVD Studio Pro project for authoring and burning.
    If you want to keep one episode per disc, DVD Studio Pro does have a 150 minute preset or you could use dual-layer discs with a higher bit rate for better quality.  Again; your call.
    >>what size DVD RW should I buy<<
    Size?  12cm.  Capacity?  Single layer, single sided DVD discs (DVD-5) have a rated capacity of 4.7Gb (4.37Gb actual), including menus.  If you use single layer discs and want to keep the quality reasonably good, you'd need at least 50 discs to complete this "set" with each disc holding roughly 2 hours of footage if you keep the menu on each disc simple.  Or, you could use dual-layer discs (DVD-9) which have a capacity of about 7.95Gb - almost doubling the recordable capacity.  There are also dual-sided, dual-layer discs available (DVD-18) but they are relatively expensive and have to be manually turned over to continue playback ... but they do have roughly 15.9Gb capacity.
    >>what bitrate should I use, and what quality I should expect for the burn<<
    Exactly; the quality is dependent on the bit rate chosen, as well as the quality of the compression.  Using compression markers where needed can greatly increase the quality of playback but will most likely increase the file size of the compressed video.  For the best quality, keeping the bit rate  as high as possible allowed under the DVD specification will yield the best quality but some DVD players may choke if the bit rate is too high.  For best quality I typically aim for a bit rate around 7.6 to 8.0Mbps but that will only allow about one hour of footage.
    Naturally, if you decrease the bit rate, you can fit more footage onto the disc but quality will be sacraficed.   Here's a chart approximating DVD bit rates and durations for single layer discs (does not include space for menus):
    3.5Mbps - 120 minutes
    5.0Mbps -   95 minutes
    6.0Mbps -   82 minutes
    7.6Mbps -   65 minutes
    8.0Mbps -   60 minutes
    -DH

  • RAID almost full, what are my options

    Hi we have a xserve RAID 5.6TB with 14 x 400Gb drives, set up as RAID 50.
    We are now getting to the stage where the RAID is getting quite full and need to start planning how we deal with this with the minimum disruption and cost, what are our options?

    The short answer is "you can't" and the longer answer is "maybe you can but you shouldn't".
    If you did find another Xserve RAID with 400GB drives in it you maybe could create a giant RAID 0 from the underlying RAIDs but the potential for data loss with some many moving parts underneath would make it IMHO unacceptable. And even if you did get that to work you would need to restripe the new RAID and wouldn't be able to just "expand" the current one.
    As usual William is right. Your best option is to buy a larger capacity box like a Promise RAID and migrate your current data to it. The next best option would be to see if you can find 16 Xserve RAID compatible 750GB PATA drives and replace your 400s. But this would require backing everything off and then restoring the data AND those drives are getting very hard to find.
    Sorry the news isn't better but mixing too many or mismatched (in terms of speed and/or size) parts into a single volume is bad idea AND without a fancy filesystem designed to expand endlessly it's hard to keep the same volume going perpetually. As a performance issue you really do want to limit how many simultaneous writes you're doing on a single journaled HFS volume. Since every change needs to get written to the journal if there are too many changes the journal can become a performance choke point. While this is more a function of use and number of users a single 9TB+ volume would hold the potential for this kind of conflict.
    My $.02,
    =Tod

  • Want to downgrade from Leopard to Tiger - what are my options?

    Hi,
    I installed Leopard on my partner's iBook G4 (1.2ghz) and its speed has reduced to a crawl. I would like to go back and re-install Tiger from its original install discs but need to retain the home folder. What are my options and am I going to come across any issues downgrading? (aside from any apps that require Leopard)
    Thanks,
    Neil

    If you had an external FireWire hard disk drive enclosure,
    of the bootable-type chipset, Mac compatible, and chose
    to clone the Leopard full installation to that external drive
    (as most externals do have or can be equipped with a
    faster spinning hard disk drive, it boots performance and
    could be used at home for desktop computing) it is very
    possible to clone the OS X and everything off the iBook
    and again try your luck with Tiger 10.4.11 in the iBook.
    If clones appear to be an option, be certain the cloned
    computer contents (a full computer clone) is made on
    a partitioned hard disk drive in proper enclosure; and
    the clone is tested prior to erasing the host computer's
    original drive contents. You can make clones and then
    there are Clones. Some can just work, but once in
    awhile, they don't. The two well known clone utilities
    are good options, and reading up on the topic helps.
    re: Carbon Copy Cloner, Bombich; and Super Duper.
    Free space may be at a premium in the small internal
    hard disk drive of the iBook; and older previous system
    folders, saved from other Archives, Updates, etc may
    have to be looked for, and trashed if they exist.
    The latest iLife 09 was not recommended in some
    hardware configurations by users and others who
    tried that version in older PPC hardware; the iTunes
    is a download, so it should work in Tiger equally well.
    The iDVD and iMovie, may have issues; iPhoto is
    OK in some older PPC G4s and not others.
    And older applications added to the installation which
    worked well under Tiger may not be happy in Leopard.
    And your mileage may vary...
    Good luck & happy computing!

  • What are our options for iWeb sites, in relation to iCloud? Is Apple dropping this type of hosting service?

    My husband and I have relied upon iWeb for our web sites for years....what now?
    Apple needs to address this issue soon! What are our options now, Apple, with iCloud?

    Great. Now really, what about iWeb Steve? http://twitpic.com/583j3k
    But seriously, it seems like many people are just trying to seed these discussions (about how upset people are over the unknown fate of iWeb) with suggestions such as; Try this or that web site building alternative, or Apple isn't obligated to you, or "you can easily publish your site to another server" blah, blah, blah. The fact is, thousands of people (or more) have learned to count on iWeb and Apple's one click publishing AND hosting to make their web sites. They have learned to make great looking web sites quickly with iWeb. They like iWeb. Some of us have used it for years. Apple is likely pulling the rug out from under ALL of these people. Many Sites, Blogs, Podcasts, Business Sites etc. will now simply cease to be if Apple stops supporting iWeb during the transition to "iCloud".
    The most frustrating thing of all is that Apple has not (as of yet) even said one thing about what will happen to all of the web sites already created with iWeb. They are just ignoring it so far. They have only given the press releases about MobileMe going away. It is rude in my opinion. Trying to "spin" the dialog about it now is not what is needed. I agree that Apple needs to answer the many legitimate concerns all the iWeb users are raising. And the sooner the better.

  • Ipad does not use flash player.  What are my options?

    What are my options since ipad does not use flash player?

    No Flash for iPads, iPhones, or iPods
    Here's why there's is no Flash available for iDevices or other mobile devices. Adobe was unable to provide a product that was suitable to the needs of battery powered mobile devices used for Internet browsing. Existing Flash technology used too much memory, ate battery life, and was buggy. Simply put Flash did not work well on mobile devices.
    Apple's Steve Jobs led the escape from Flash dependency when Apple introduced the iPhone, and later introduced the iPad. There was a hue and cry over the omission. Time proved Jobs was right on target.
    So this is why there is no Flash for your iPhone or iPad or iPod nor for most SmartPhones. Flash has been abandoned by many sites in favor of supported technologies such as HTML5 or by providing their own custom app.
    Here is Steve Jobs official comment on his momentous decision to omit Flash from iDevices: Steve Jobs on Flash.
    Here is Adobe's later announcement to cease development of Flash for mobile devices: Adobe on Mobile Flash. Adobe is not providing Flash for Apple iOS devices, and they no longer provide Flash for any other cellular phones. Flash is officially gone.
    Now, you are not necessarily out on a limb. There are some apps that can display some Flash, but don't count on there ability to display anything using Flash.
    A sample of Apps that can display some Flash content:
      1. Puffin
      2. SkyFire
      3. Photon Flash
      4. Browse2Go
      5. Swifter
    Also, note that many sites that use Flash provide their own app for accessing their material. So check with your favorite sites and find out if "there's an app for that."

  • What are my options (Java)?

    Hi all,
    I have a macbook (2009) running on OS v 10.5.8. I've read that there are no more Java updates made for this version. I need it for school. Some of the lessons I need aren't opening properly. What are my options at this point? Can I even get Java on my macbook anymore?
    Thanks
    Nichole

    There is no further update to Java for Leopard than this one:
    Update 10, 29 June 2011 - This release updates J2SE 5.0 to 1.5.0_30, and updates Java SE 6 to 1.6.0_26. J2SE 1.4.2 is no longer being updated to fix bugs or security issues and remains disabled by default in this update. Support for out-of-process Java applets on Mac OS X 10.5 Leopard has been removed with this update.
    This release is only for Mac OS X 10.5.8 or later versions of Mac OS X 10.5. http://support.apple.com/kb/DL1359

  • Director 5 movies - What are my options?

    Hello,
    My company produced a CD-ROM for troubled teenagers in 1998 with Director 5 (I think). Lots of Quicktime movies (v.2.1!) and buttons (lingo). The content is still very much relevant and we have been asked to uprade the product.
    What are my options now?
    Can I convert it for Shockwave and the Web or will there be too many lingo issues?
    Should I reopen the files, if at all possible, in a newer version of Director and work out the problems one at a time?
    Should I give up?
    Any advice is most welcome. Thank you in advance.

    Can I convert it for Shockwave and the Web or will there be too many lingo issues?
    You can't readily convert it for Shockwave use without first updating the file format to a newer version. You should start with updating the files in Director 7 which is the first version (IIRC) to use QT3 (the "modern" QuickTime for Windows engine). Development using Director underwent some major changes between 5 and 7 with the introduction of behavior scripts and sprite spans etc., so you should get your content working in D7 before progressing as this step will be the hardest. How complicated is impossible to say without seeing it, but I don't think you should give up without trying.

  • I have an old Imac G4 from 2003. I haven't used it in years, but I would like to start. What are my options for getting it up to date? Is it even worth the trouble/cost? I was hoping to at least get it running Snow leopard, if not Lion. Options?

    I have an old Imac G4 from 2003. I would like to start using it again, however it is so out of date and runs too slowly. What are my options to update it? I really don't want to invest a ton of money - I might as well get a new one, so if there are any reasonable ways to get it to run Snow Leopard or even Lion, please help. I've also considered using a mac mini? Is that worth it either? I'm not sure which way to go here. I don't want to trash it, I feel like it can be a great computer if updated.

    Presumably it is running tiger 10.4.11?
    It may be able to run Leopard 10.5:
    Leopard system requirements:
    http://support.apple.com/kb/SP517
    But that is as far as the old PPC Macs can go, and Leopard can cost up to $200 on Amazon.

  • HT201407 hi..I cant activate my Iphone 5. I bought this from someone who cant remember her apple password and even the email address that she used to set up the account.What am I gonna do now....How can I activate my Iphone. what are my options...pls help

    hi..I cant activate my Iphone 5. I bought this from someone who cant remember her apple password and even the email address that she used to set up the account.What am I gonna do now....How can I activate my Iphone. what are my options...pls help me.thank you

    Activation Lock in iOS 7  >  http://support.apple.com/kb/HT5818
    hannibalfromlemery wrote:
    .I cant activate my Iphone 5. I bought this from someone
    The Apple ID and Password that was Originally used to Activate the iDevice is required.
    If you cannot get this information from the seller
    Removing a device from a previous owner’s account
    You need to return the Device for a refund, as you will not be able to re-activate it.

Maybe you are looking for

  • Can't Change Credit Card Number, told to reregister but can't find reregister button

    Hello, Sorry to be a trouble, But I can't change my credit card # (because BBapps will not allow me to log on to control panel to do so. Made the mistake as a 1st timer to assume would ask for credit card number after I purchased Documents to Go. Did

  • DVD Problems/Possible Exchange?

    My DVD player in my new iMac G5 wasn't reading my DVD's a couple of nights ago, and it had been working before. I was just wondering if, once I looked into it more, I found out it was broken, could I get it exchanged? I would think I could b/c I have

  • Creating a restricted access page.

    I need to create a restricted access page within my website, so that a username and password are required to access. The Dreamweaver instructions ask me to go to the Server Behaviors panel (Window > Server Behaviors), click the plus button and choose

  • OBIEE 11g additional table in the generated sql

    Hi gurus, In OBIEE 11g RPD, we have a fact table whose source table is consisted by table A, B, C. Table A joins to table C while table B joins to tables C. And in the content tab, table C is used to filter out some records . If we select a column of

  • No playoffs on NFL Mobile??

    Are the playoff games not available to watch on NFL Mobile? Everything else is available (play by play, radio, ect..) however, the option to watch is not. Does it have to do with Verizon Videos being discontinued?  I am using a BlackBerry Torch 9850.