Problems after new New Power battery

Just installed a new high capacity New Power battery in my G4 1.42 GHz. I did the PMU reset, and battery calibration as recommended by New Power.
However, now, instead of going into sleep mode when battery runs down, the computer turns off. This happens when the battery gets down to around 15 minutes on the menu bar.
I don't mind (at least not too much) the computer turning off before the minute counter gets down to the end, but not going into sleep mode is a problem, as I lose whatever I'm working on.
This problem has probably been covered on this board, but I haven't been able to find it.
Any help is appreciated.
Ed

Same problem! Does your battery icon in the menu bar go red at about one hour run time left? What about the Amperage number in the About this Mac - is it a negative number?
See both my posts:
http://discussions.apple.com/message.jspa?messageID=8248752#8248752
and
http://discussions.apple.com/message.jspa?messageID=8266683#8266683
I too can live with this, just wondering if you are having the same issues I am.
Have you spoken with any of the technicians? They told me someone with a G4 just called with the same issues, was it you?
Mrs H

Similar Messages

Problem after upgrading New Firmware 14.1.G.1.534. Asking for Password when i click settings menu

Problem after upgrading New Firmware 14.1.G.1.534. Asking for Password when i click settings menu, for which i never kept any password.
Any DEFAULT Password so that i can unlock the settings menu.

That's quite odd, just repeat the update process
Update Service (SUS)
http://www.sonymobile.com/gb/tools/update-service/
http://www-support-downloads.sonymobile.com/Software%20Downloads/Update_Service_Setup-2.11.12.5.exe
PC Companion (PCC)
Bridge (for Mac)
Alternatives on How to backup Xperias
http://talk.sonymobile.com/thread/36355
"I'd rather be hated for who I am, than loved for who I am not." Kurt Cobain (1967-1994)

My problem after N73 New firmware

Dear All
V 4.0727.2.2.1
Hello
i have a problem after i pdate my firmware for Nokia N73
the problem is: before When I started to make a call the counter appear on the screen and when the other side open the line the counter start the count the time. This is useful to see the call time during the call process
But after the new firmware I did not find this service and I can not fix it.
How I can fix it?
Also, how I can back to the old firmware?
Is there a program to do the same service?

That's quite odd, just repeat the update process
Update Service (SUS)
http://www.sonymobile.com/gb/tools/update-service/
http://www-support-downloads.sonymobile.com/Software%20Downloads/Update_Service_Setup-2.11.12.5.exe
PC Companion (PCC)
Bridge (for Mac)
Alternatives on How to backup Xperias
http://talk.sonymobile.com/thread/36355
"I'd rather be hated for who I am, than loved for who I am not." Kurt Cobain (1967-1994)

Exchange 2007 - Outlook Anywhere problems after installing new SSL cert

*** Original thread posted on wrong forum ***
Hi all,
Exchange 2007 environment (2x CAS, ISA2006). Not much familiar with Exchange.
Problem: 20-odd machines off the domain use Outlook Anywhere (XP with Outlook 2010). AUthentication pop-up and not able to connect.
Company has recently changed its name and we have to renewed the SSL cert. Previous SSL cert. was issued to: webmail.oldcompname.co.uk (several SANs on that cert., including internal server names).
Applied for a new UCC SSL cert issued to: newcompanyname.com (also includes webmail.newcompanyname.com ; autodiscover.newcompanyname.com + old SANs).
The setting on those machines point the proxy to the following:
Https://webmail.oldcompname.co.uk (which is fine since it is in the cert and can be accessed)
Only connect to proxy servers that have this principal name in their cert.:
msstd:webmail.oldcompname.co.uk (I believe this is the problem since the new UCC SSL cert. was issued to newcompanyname.com).
Browsing technet + internet it seems that I need to look into OutlookProvider EXPR.
When I run Get-OutlookProvider everything is blank (I believe I should be concerned to EXPR only for Outlook Anywhere).
I am thinking of running: Set-OutlookProvider -Identity EXPR -CertPrincipalName msstd:newcomanyname.com
My only concern is whether this might break something else in the Exchange environment, especially as we have 100+ users on smartphones connecting via SSL on webmail.oldcompname.co.uk
Is it save to run this command? Do I need to re-start IIS? Do I need to look into any settings on ISA2006?
Comments/help are much appreciated.
Regards

Hi,
According to the description, I found that we re-new a SSL certificate.
"I am thinking of running: Set-OutlookProvider -Identity EXPR -CertPrincipalName msstd:newcomanyname.com"
Just do it. Then remove the old certificate on ISA server and install a new one.
Found a similar thread for your reference:
Renewal of SSL certificate in exchange 2007 with ISA 2006
http://social.technet.microsoft.com/Forums/exchange/en-US/25770038-8491-470a-92fa-8ae50674b7a6/renewal-of-ssl-certificate-in-exchange-2007-with-isa-2006
Hope it is helpful
Thanks
Mavis
Mavis Huang
TechNet Community Support

Problems after installing new memory stick

The problem that I have is this:
I have an iMac PPC G5 2.1 GHz 20" w/ built-in iSight which was purchased in April 2006. Last week I purchased a certified 1 GB stick of RAM from OWC. I installed the RAM per the instructions given in the owner's manual. I restarted my computer and the RAM was not recognized in "About This Mac", nor was it listed in the Apple System Profiler. I thought that maybe I hadn't seated the RAM properly, so I removed the stick and repeated the installation process. I called and spoke to a tech at OWC who walked me through resetting the PRAM and NVRAM. This was not successful in forcing the RAM to be recognized. I have returned the RAM to OWC and am expecting a replacement from them within the next week or two.
(As a side note, after each repeat of the process, the computer would not shutdown as quickly as it had been since I purchased it. I waited for one minute and then forced a shutdown via hoding the power button in. I made two attempts at a clean install of the OS. Both times there was an error at the very beginning of the install process that would not allow it to continue and required a restart). I am highly concerned about the shutdown issue and the inability to re-install the OS.
Has anybody had or heard of an issue like the one that I have just decribed?
iMac G5 20" iSight Mac OS X (10.4.7) w/ Bluetooth keyboard & mouse

I completed the Disk Warrior rebuild but it did not solve my problem. It has even added a new problem. Now the "Starting Mac OS X..." progress bar that runs prior to the appearance of the desktop image is still on my screen after the desktop image is loaded. It is starting to look like I need a fresh install of the OS, but I can't do that either. Somebody please help!!! I am glad that I bought the AppleCare protection.
I am going to give the "fsck" thing a try before I give up.
iMac G5 2.1 GHz 20" iSight Mac OS X (10.4.7) w/ Bluetooth keyboard & mouse
Message was edited by: CT Mac Addict

Problem after installing new AMD FX-4170 processor

Hello,
i just installed AMD FX-4170 on my MSI 890GXM-G65 mainboard. Then, when i start my computer, everything seems to be fine, all fans are working, those 4 proc. power LEDs are shining, everything is powered. But i get no signal to my monitor, cant get to BIOS, keyboard not working, nothing. I tried two different graphic cards, even that integrated one (not sure if it would work, when disabled in BIOS) nothing changed.
Same problem is when i place back the old Phenom processor. Black screen, from time to time No signal message on my monitor.
I have the lates BIOS 1.d.
Any suggestion?
Or am I screwed and have to buy new maiboard, because this one is somehow damaged?

clear CMOS helped. Computer is not very stable, second SSD disk (F: )(not the one with system) keeps disconnecting after some period of time, but at least i see what is happening it does not even show System reserved area (E: )of the system disk (C: ), that is normally visible...
RAID is set to AHCI, so it is ok.. the trick must be somewhere else.. i will check BIOS one more...

[SOLVED]Multiple Problems after a new install on Arch Linux

Hello all,
I just finished installing Arch Linux from the core ISO which I downloaded from the site. The install went smoothly and booted up fine. Also I was able to install gnome and its extras fine as well. On the first boot after installing gnome I managed to get my resolution correct also. However later on after I installed compiz fusion everything with the resolution seems to be going wrong . My computer specs are shown below :
AMD 64 3200
Asus M2N MX-SE
2 GB Ram
Geforce 8600 GT
Viewsonic VA1918wm (Native resolution is 1440x900)
At the moment I can only manage to get upto 1024x768 and it looks quite bad at that resolution. I have attached the xorg.conf I have at the moment.
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "Files"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/misc"
FontPath "/usr/share/fonts/100dpi:unscaled"
FontPath "/usr/share/fonts/75dpi:unscaled"
FontPath "/usr/share/fonts/TTF"
FontPath "/usr/share/fonts/Type1"
EndSection
Section "Module"
Load "dbe"
Load "record"
Load "extmod"
Load "glx"
Load "dri2"
Load "dri"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5 6 7"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
EndSection
Section "Device"
Identifier "Card0"
Driver "nvidia"
VendorName "nVidia Corporation"
BoardName "G84 [GeForce 8600 GT]"
BusID "PCI:2:0:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
SubSection "Display"
Viewport 0 0
Depth 1
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 4
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 8
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 15
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
While I was trying to fix this I noticed I was encountering other problems also. For one I found that sometimes dhcpcd times out on booting up and I cant seemt o connect to the Internet on booting. Although I just thought of trying a static IP and I'll post if that helped later on.
Another problem is I found that I seem to get the following error randomly. Pressing ctrl + D after this just restarts the machine.
The superblock could not be read or does not describe a correct ext2
filesystem. If the device is valid and it really contains an ext2
filesystem (and not swap or ufs or something else), then the superblock
is corrupt, and you might try running e2fsck with an alternate superblock:
e2fsck -b 8193 <device>
Finally, while I boot up I noticed that it says "Mounting root partition as read only [DONE]" Is the root partition supposed ot be mounted as read only ? Attached my fstab just in case it is needed.
# /etc/fstab: static file system information
# <file system> <dir> <type> <options> <dump> <pass>
none /dev/pts devpts defaults 0 0
none /dev/shm tmpfs defaults 0 0
#/dev/cdrom /media/cd auto ro,user,noauto,unhide 0 0
#/dev/dvd /media/dvd auto ro,user,noauto,unhide 0 0
#/dev/fd0 /media/fl auto user,noauto 0 0
/dev/sda3 /boot ext3 defaults 0 1
/dev/sdb1 / ext3 defaults 0 1
/dev/sdb2 swap swap defaults 0 0
/dev/sdb3 /home ext3 defaults 0 1
As you can see I'm quite new to Arch Linux so any help would be deeply appreciated.
Last edited by FilledVoid (2009-09-11 16:28:28)

Thank you for all your suggestions . I tried replacing the ID to Card0 but it didnt seem to fix it . However on the bright side I checked more threads on the forum and found some that helped out . :)
http://bbs.archlinux.org/viewtopic.php?id=75070&p=2
http://bbs.archlinux.org/viewtopic.php?id=72788
http://bbs.archlinux.org/viewtopic.php?id=76938
I copied the xorg.conf file from the third link and just made minor changes to it like removing all the resolutions I didn't need and now its working fine :).
Now Im just stuck with two problems. One is the following message which appears randomly.
The superblock could not be read or does not describe a correct ext2
filesystem. If the device is valid and it really contains an ext2
filesystem (and not swap or ufs or something else), then the superblock
is corrupt, and you might try running e2fsck with an alternate superblock:
e2fsck -b 8193 <device>
******************* FILESYSTEM CHECK FAILED *************
* Please repair manually and reboot. Note that the root *
* filesystem is currently mounted read-only. To remount *
* it read-write type: mount -n -o remount,rw / *
* When you exit the mantenance shel the system will *
* reboot automatically. *
A thread about the same can be found http://bbs.archlinux.org/viewtopic.php?pid=295384 but there isn't a solution on it.
The second is the intermittent problems with the Network being setup. Sometimes when I boot up it just says dhcpcd timedout and I won't be able to connect . However I can connect on another machine at the same time.
Took a look at the drive in question with gparted and it shows the below information:
/dev/sdb1 ext3 / 32.59 GB 4.92 GB 27.68 GB boot
By any chance is any of the above information relevant :x ?

Any fix for random art and song order problems after adding new music?

If I sync my touch with itunes as a restore, all cover art, albums and playlists are correct. Once I add anything new or make a change and re-sync, random cover art is missing and random songs are in the wrong order. The only way to fix the problems is through a complete restore. Has anyone else had this problem or figured out a fix? I am using the latest itunes on a PC with XP.

A few issues, but sorry let me try to understand.
Adding new music, 'XXXX's iPod cannot be written or read'' can you let me know the number. most likely music format is not iPod Compatible like HE-AAC.
started skipping songs - these are normally due to corrupted ID3 tags, try converting them -File-> Advance -> IPOD version or use MP3 validator to fix all songs in the library. (My Apologies, only work for MP3 music that skipped)
As for item 2, you can try Hard Reset if you like to download MP3 validator.
After charging till full charge, at least 2 hours (preferably 4 hours)
Toggle the Hold switch, make sure you dont see the red mark when you do the next step
Reset the iPod -> Press Menu and Center button simultaneously for about 10 secs till the Apple Logo comes ON
Then release the buttons
Select your preferred language.
Here is the Apple support Article on the 5Rs
http://www.apple.com/support/ipod/five_rs/classic/
Good Luck!

Problems after installing new version o iphone 3gs

I installed this evening the new version of my iphone 3gs and since then I cannot use my iphone nor reinitialise it beause it asks me to connect to itunes.When i connect it to the computer it say there is no pilot and doesnt manage to install a new pilot I telecharged the last version of itunes and reinstallated it, try again to reinstall the pilot but impossible to connect and I can't use my iphone
Help me please

A warm welcome Sabina!
i wonder if the issue is the new battery (can that cause a slow down
and malfunction of this sort).
Not too likely at all.
or if my HD is the problem.
Very likely, I would expect all Laptop HDs 4 or more years old to be failing by now.
i just read somewhere that whenever we do the updates we're supposed to do the permissions and i never knew to do that -- so i haven't ever done it. could that be the problem.
That and Verifying or Repairing the HD are sort of like looking both ways before you cross the street, neither may be necessary to cross the street, but it certainly can prevent problems during the crossing!
should i do a clean install of the system software and start from scratch.
I really think the Internal HD is on it's way out, but if you have a good/complete backup, actually a bootable clone on an external Firewire Drive is preferable... Best way to get an exact bootable copy of your old drive to the new one is with Carbon Copy Cloner...
http://www.bombich.com/software/ccc.html
thoughts would be appreciated. i don't have the money to take it anywhere to be fixed or to buy new -- so any help is greatly appreciated.
Without Money to replace the HD, you may be stuck booting off an external HD

HDD problem after installing new SSD

i bought a Kingstone SSD 60GB, and procced to a clean installation in my HP DV7-1020us laptop wich i love. All nice and good... i got out the HDD, install SSD in previously used HDD slot, install windows 7 on SSD partition, put the HDD in second hard drive bay that was it.
The problem is... after couples shuts down of my laptop (still working good), one time when i started, my laptop spent like 10-15 mins trying to start up the windows , ( i could hear my old HDD working hard) and after that i wanted to reach my HDD but i couldnt... i double click on the partition i want to open and my HDD starts working hard hard and in the end it says that i need to format it so i can acces it. My hdd haves 3 partitions... i runned disk checks and repairs and still doing the same. I finally formated all of it... all of my HDD partitions including the Recovery partition. My HDD works fine until i shut down my laptop for the first time after formating, then another 10-15 mins to start up and shut down the windows. Also if i connect my hdd via USB everything is fine ( if i previously format the HDD and connect it via USB). But if i move it back into my laptop in my sata slot things goes bad again. Also if i wait 10 mins at start up, get the hdd out and connect it via usb it still runs very ver very slow, and one partition asks me for formating. So i'm thinking that my second sata slot connection does something bad to my hdd.
I'm thinking that my second sata slot haves some problems... what should i do? I dont like my HDD working on my USB, it's a laptop, everything has to be integrated.
Oh and if i move my ssd from first sata slot to my second one, it says "please insert bootable device...."
Thank you, if u need more information please ask me

Hi mykey651,
Thank you for your query, I will do my utmost to assist you.
I grasp you have installed a SSD drive as the main drive and the original drive as a secondary. All works well until you reboot and then it is unable to locate the SSD.
Here is a link to HP Notebook Hard Drives & Solid State Drives Identifying, Preventing, Diagnosing and Recovering from...
If that has not helped, I suggest you go out to the bios and restore the defaults. This will reset the system and make it scan for installed hardware. This should help it to find the new SSD as the boot drive.
Here are two more documents that may be of help.
About Solid State Hard Drives
How to Install an SSD (Solid State Drive
Hope this helps and have a great weekend.
Sparkles1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

Problems after installing new PSU

I have a very unstable system after replacing the PSU. Her is a list of issues encountered.
I had worked on my PC today then left it running as usual while I was away. Came back and my PC was "sleeping" reawakened and it fired up except the screen remained black. Tried several times to restart...same effect. Went into bios and couldn't see anything untoward but did change my start sequence thinking this may have an effect. Finally got my pc to light up the screen only to find the following messages. The previous performance overclocking failed?
Keep your current bios settings y or n. Now I don't overclock as far as I know?? I went back to bios and changed a few minor settings. Tried to restart and got as far as Windows is starting which promptly froze. Tried restarting again and got to a black screen wiyh flashing cursor in top left. Went back to bios and set failsafe default settings. This time my pc fired up. What is going on, I am really getting anxious as replacing my PSU was (I thought) going to bring stability back to my PC. Why does my PC fail to wake up? I have bios set on S3, and enabled the relevant resume choices. I need help....thanx

It worked !!! I thought i had already reseted the bios but seems like using the menu didnt do it. The computer is now working as b4 thx god it isnt some damage on my hardware !!! Should I now access BIOS and save to default again ? I set the time manually in windows dont know if that is the best way to go around it anyways I am going to search about it. Btw the PSU is XFX the GPU is from MSI. How should i proceed now, should I keep with the RMA and make sure its not faulty or the problems that arose with it are all explained by problems in the BIOS and there is no reason to be afraid of the new PSU? Thx alot again !!!

Startup problems after instaling new graphics card drivers

PC: HP p6520 f with a 400 watt power supply
video card: AMD Radeon 6570 (MD1GD3)
After getting the 400 watt power supply, I was able to uninstall the intergrated graphics card's drivers, but I can't succsesfully startup after installing drivers for the new card without a system restore, which of course gets rid of the new drivers.
I've tried newer drivers, but those don't work either.
Any suggestions?

Hello Sev_07. I understand you're unable to install your video card drivers.
Are you receiving an error on boot?
Are you experiencing any issues with other pieces of hardware?
Have you tried running HP Support Assistant and Windows Update to ensure all of the software and drivers are completely up to date?
It may also be helpful for you to provide your product number so I can look at your computer's specifications. This document can show you where this is located.
I hope you have a great day!
Please click the white star under my name to give me Kudos as a way to say "Thanks!"
Click the "Accept as Solution" button if I resolve your issue.

Mailbox problems after the "new, improved" version messed up all my stuff

OK ... so I finally got sync to work ... tried a hint from the forum, with my own variation (started it while on the desktop, rather than after I put it back into "preferences") ... and sync actually WORKED!
HOWever ... the mailbox STILL seems to want to enter every incoming as TWO ITEMS ... and it COUNTS them the same way ... until I click on both ...
THE MAIN PROBLEM, tho, is that when I click on a new email (or an old one), the message that is brought up is NOT the one indicated ... age of the items viewed ranges from 10 to 18 months old ...
An example: my spouse sent me an email ... it shows up in the "old" Mail site, AND on the MailMe location ... it's readable in MailMe, BUT THE JUNK FILTER WILL NOT WORK ... so I must weed thru the crap, or ... go back to the Mail site, let the junk filter work, and then go back to MailMe to read only the "real" messages, without being bothered by all the extraneous junk ...
Anyone have any thoughts or suggestions? Anyone? Bueller?

You've posted this in the iSync forum. However, iSync doesn't sync mail at all - it just syncs Contacts and Calendars to mobile phones and PDAs.
Presumably, you're referring to MobileMe Sync, for which the correct forum is here:
http://discussions.apple.com/forum.jspa?forumID=1264

Automatic Mailbox Distribution problem after Creating New AD Site

We redesigned our Active Directory Sites a little while ago. We moved the subnets and servers from the old sites to the new sites. We haven't removed the old sites yet, but that will happen soon. We haven't noticed any issues with the new
sites except for one weird issue and that is that Automatic Mailbox Distribution no longer works, in fact if you don't specify a database with the enable-mailbox (or new-mailbox) commands it will fail with an error that load balancing failed to find a valid
mailbox.
The problem, from the output of an enable-mailbox, command appears to be a site problem (from the fact that the automatic mailbox distribution discards sites that are not in the same site as the user). The verbose output has the command checking the
old site even though the server is in the new site. I've already checked the databases and none of them have the IsExcludedFromProvisioning or IsSuspendedFromProvisioning properties set to TRUE
My question is how do I make the databases show up as in the new site rather than the old site?
Any and all help with this issue is appreciated.
This is the output from the command:
VERBOSE: [16:36:50.864 GMT] Enable-Mailbox : Initializing Active Directory server settings for the remote Windows
PowerShell session.
VERBOSE: [16:36:50.864 GMT] Enable-Mailbox : Active Directory session settings for 'Enable-Mailbox' are: View Entire
Forest: 'False', Default Scope: 'domain.local', Configuration Domain Controller: 'DC01.domain.local', Preferred Global
Catalog: 'VMDC01.domain.local', Preferred Domain Controllers: '{ VMDC01.domain.local }'
VERBOSE: [16:36:50.864 GMT] Enable-Mailbox : Runspace context: Executing user: domain.local/All Users/AD/Admin1,
Executing user organization: , Current organization: , RBAC-enabled: Enabled.
VERBOSE: [16:36:50.864 GMT] Enable-Mailbox : Beginning processing &
VERBOSE: [16:36:50.880 GMT] Enable-Mailbox : Instantiating handler with index 0 for cmdlet extension agent "Query Base
DN Agent".
VERBOSE: [16:36:50.880 GMT] Enable-Mailbox : Instantiating handler with index 1 for cmdlet extension agent "Rus Agent".
VERBOSE: [16:36:50.880 GMT] Enable-Mailbox : Instantiating handler with index 2 for cmdlet extension agent "Mailbox
Resources Management Agent".
VERBOSE: [16:36:50.880 GMT] Enable-Mailbox : Instantiating handler with index 3 for cmdlet extension agent "Mailbox
Creation Time Agent".
VERBOSE: [16:36:50.880 GMT] Enable-Mailbox : Instantiating handler with index 4 for cmdlet extension agent
"Provisioning Policy Agent".
VERBOSE: [16:36:50.880 GMT] Enable-Mailbox : Instantiating handler with index 5 for cmdlet extension agent "Admin Audit
Log Agent".
VERBOSE: [16:36:50.927 GMT] Enable-Mailbox : Current ScopeSet is: { Recipient Read Scope: {{, }}, Recipient Write
Scopes: {{, }}, Configuration Read Scope: {{, }}, Configuration Write Scope(s): {{, }, }, Exclusive Recipient Scope(s):
{}, Exclusive Configuration Scope(s): {} }
VERBOSE: [16:36:50.927 GMT] Enable-Mailbox : Searching objects "domain.local/All Users/SM/GP/User1" of type
"ADUser" under the root "$null".
VERBOSE: [16:36:50.942 GMT] Enable-Mailbox : Previous operation run on domain controller 'VMDC01.domain.local'.
VERBOSE: [16:36:50.974 GMT] Enable-Mailbox : Load Balance : Database container located at 'CN=Databases,CN=Exchange
Administrative Group (FYDIBOHF23SPDLT),CN=Administrative Groups,CN=DOMAIN,CN=Microsoft
Exchange,CN=Services,CN=Configuration,DC=DOMAIN,DC=local'.
VERBOSE: [16:36:50.974 GMT] Enable-Mailbox : Searching objects of type "MailboxDatabase" with filter
"(&((IsExcludedFromProvisioning Equal False)(IsSuspendedFromProvisioning Equal False)(Recovery Equal False)))", scope
"OneLevel" under the root "Databases".
VERBOSE: [16:36:51.005 GMT] Enable-Mailbox : Comparing local site 'OLD-SITENAME' with database site 'OLD-SITENAME'.
VERBOSE: [16:36:51.021 GMT] Enable-Mailbox : Comparing local site 'OLD-SITENAME' with database site 'OLD-SITENAME'.
VERBOSE: [16:36:51.021 GMT] Enable-Mailbox : Comparing local site 'OLD-SITENAME' with database site 'OLD-SITENAME'.
VERBOSE: [16:36:51.021 GMT] Enable-Mailbox : Comparing local site 'OLD-SITENAME' with database site 'OLD-SITENAME'.
VERBOSE: [16:36:51.021 GMT] Enable-Mailbox : Comparing local site 'OLD-SITENAME' with database site 'OLD-SITENAME'.
VERBOSE: [16:36:51.021 GMT] Enable-Mailbox : Comparing local site 'OLD-SITENAME' with database site 'OLD-SITENAME'.
VERBOSE: [16:36:51.036 GMT] Enable-Mailbox : Comparing local site 'OLD-SITENAME' with database site 'OLD-SITENAME'.
VERBOSE: [16:36:51.036 GMT] Enable-Mailbox : Comparing local site 'OLD-SITENAME' with database site 'OLD-SITENAME'.
VERBOSE: [16:36:51.036 GMT] Enable-Mailbox : Comparing local site 'OLD-SITENAME' with database site 'OLD-SITENAME'.
VERBOSE: [16:36:51.036 GMT] Enable-Mailbox : Comparing local site 'OLD-SITENAME' with database site 'OLD-SITENAME'.
VERBOSE: [16:36:51.036 GMT] Enable-Mailbox : Comparing local site 'OLD-SITENAME' with database site 'OLD-SITENAME'.
VERBOSE: [16:36:51.036 GMT] Enable-Mailbox : Comparing local site 'OLD-SITENAME' with database site 'OLD-SITENAME'.
VERBOSE: [16:36:51.052 GMT] Enable-Mailbox : Comparing local site 'OLD-SITENAME' with database site 'OLD-SITENAME'.
VERBOSE: [16:36:51.052 GMT] Enable-Mailbox : Comparing local site 'OLD-SITENAME' with database site 'OLD-SITENAME'.
VERBOSE: [16:36:51.052 GMT] Enable-Mailbox : Comparing local site 'OLD-SITENAME' with database site 'OLD-SITENAME'.
VERBOSE: [16:36:51.052 GMT] Enable-Mailbox : Comparing local site 'OLD-SITENAME' with database site 'OLD-SITENAME'.
VERBOSE: [16:36:51.067 GMT] Enable-Mailbox : Comparing local site 'OLD-SITENAME' with database site 'OLD-SITENAME'.
VERBOSE: [16:36:51.067 GMT] Enable-Mailbox : Comparing local site 'OLD-SITENAME' with database site 'OLD-SITENAME'.
VERBOSE: [16:36:51.067 GMT] Enable-Mailbox : Comparing local site 'OLD-SITENAME' with database site 'OLD-SITENAME'.
VERBOSE: [16:36:51.067 GMT] Enable-Mailbox : Comparing local site 'OLD-SITENAME' with database site 'OLD-SITENAME'.
VERBOSE: [16:36:51.067 GMT] Enable-Mailbox : Load Balance : The search for databases returned an empty result. This
could happen if all databases are excluded from the Load Balance process.
VERBOSE: [16:36:51.067 GMT] Enable-Mailbox : Load Balance : There is no available database. Refer to previous verbose
messages for more information.
VERBOSE: [16:36:51.067 GMT] Enable-Mailbox : Admin Audit Log: Entered Handler:OnComplete.
Load balancing failed to find a valid mailbox database.
+ CategoryInfo : NotSpecified: (0:Int32) [Enable-Mailbox], RecipientTaskException
+ FullyQualifiedErrorId : 4AE0EA04,Microsoft.Exchange.Management.RecipientTasks.EnableMailbox
VERBOSE: [16:36:51.083 GMT] Enable-Mailbox : Ending processing &

Hi,
From your description, I would like to clarify the following thing:
By default, all online and healthy mailbox databases on Exchange 2010 servers in the local Active Directory site can be chosen by automatic mailbox distribution to store a new or moved mailbox. Mailbox databases in other AD site can't be chosen by automatic
mailbox distribution to store a new or moved mailbox.
What's more, I recommend you use the following cmdlet to enable mailbox and check the result.
Enable-Mailbox -Identity xxx -Database xxx
Hope it helps.
Best regards,
Amy Wang
TechNet Community Support

Permissions problems after installing new hard drive

I backed up my old hard drive with SuperDuper!, then installed a new hard drive. When I tried to install my backup on the new hard drive with Disk Utility, it would work fine and then hang. It wouldn't finish, even overnight. So I installed a clean copy of leopard on the new hard drive, and then used Migration Assistant to move everything over from my backup. Worked great, until I actually tried to use the computer. Tons of permissions issues, mail and address book wouldn't run, Skype won't run even after installing an upgraded version, etc. What's weird, is my main account is an administrator account, but logging on as root and trying to remove admin permissions from my main account, the checkbox is greyed out! I also don't have a UID 501 on the system. I'm 502, and my wife's account is 503. I can't fix permissions from the finder, and in certain cases can't get them changed in terminal logged in as root. I don't know how to get my data from my old hard drive (which is running 10.5.1) to my new hard drive (also 10.5.1) Please help me! Thanks.

Hey Shawn,
Have you looked at the permissions with "Get Info"? Are they listed as belonging to "unkown user"?
First of all, see the Apple doc <href="http://docs.info.apple.com/article.html?artnum=306876">Administator user changed to standard.
After you clear that up, you'll probably have to remove the "unkown user" and add your user as the owner of all your folders. During that process, finder will probably crash. At that point, try running <a href="http://discussions.apple.com/thread.jspa?messageID=5670342#5670342>this terminal command described in "mlaster's" second posting.
Good luck!
CMF

Problem after getting new hard drive

Okay, don’t laugh but I think I am using Photoshop elements 1 and yes it works on windows 7. The systems information does say something about version 6.1 service pack 1. Anyhow it has worked great for no more than I do.
Last week I had to get a new hard drive. Supposedly everything was “ghosted” over from the old to the new.
Now my elements work well until I try to save the edited image. I then get “Could not save as "C:\...\SANYO4b.jpg" because of a program error”.
I uninstalled and reinstalled. Same thing. I searched Google for over an hour and the only thing I came up with to try was to change all my scratch disks to C.
Still no luck. Any ideas?

“If you right click on the Photoshop elements 1 shortcut and choose Run as Administrator, does the saving work?” YES!
Back to this “Permissions” Issue.
when I right click on c drive and go to
properties-security i get
group or user names (and this info about them)
authenticated Users- nothing checked
system- full control
Administrators (myname-PCAdministrators)- full control
User (my name-PC\Users) only has checked
read and execute
list folder contents
read
The others (full control, Modify, write and special permissions) are NOT CHECKED.
Thinking this might be the problem, when I started to change the “User (my name-PC\Users)” to full control I got the warning that “changing the root directory of the startup disk can result in unexpected access...etc.”
Could this be the problem and if so should I let those warnings about dire consequences stop me?

Problems after new New Power battery

Similar Messages

Maybe you are looking for