Problems dialing from a external modem to a isdn router

Hi,
I have trouble with my modem dial-in in an other router using his isdn interface.
The problem looks like the following:
The calling router:
router-2523#debug dialer events
Dial on demand events debugging is on
router-2523#ping 172.16.4.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.4.1, timeout is 2 seconds:
00:17:50: Se5 DDR: rotor dialout [best] least recent failure is also most recent failure
00:17:50: Se5 DDR: rotor dialout [best] also has most recent failure
00:17:50: Se5 DDR: rotor dialout [best]
00:17:50: Se5 DDR: Dialing cause ip (s=172.16.4.2, d=172.16.4.1)
00:17:50: Se5 DDR: Attempting to dial 51
00:17:50: CHAT5: Attempting async line dialer script
00:17:50: CHAT5: Dialing using Modem script: Dialout & System script: none
00:17:50: CHAT5: process started
00:17:50: CHAT5: Asserting DTR
00:17:50: CHAT5: Chat script Dialout started.....
Success rate is 0 percent (0/5)
router-2523#
00:18:02: CHAT5: Found abort string BUSY expecting CONNECT
00:18:02: CHAT5: Chat script Dialout finished, status = Connection aborted
00:18:02: Se5 DDR: disconnecting call
router-2523#
The called router:
router-2503-II#debug isdn events
ISDN events debugging is on
router-2503-II#debug isdn q931
ISDN Q931 packets debugging is on
router-2503-II#
00:18:58: ISDN BR0: RX <- SETUP pd = 8 callref = 0x01
00:18:58: Bearer Capability i = 0x9090A3
00:18:58: Channel ID i = 0x8A
00:18:58: Progress Ind i = 0x8583 - Origination address is non-ISDN
00:18:58: Calling Party Number i = 0x01, 0x83, '15', Plan:ISDN, Type:Unknown
00:18:58: Called Party Number i = 0x81, '51', Plan:ISDN, Type:Unknown
00:18:58: CCBRI_Go Fr L3 pkt (Len=27) :
00:18:58: 5 1 81 90 4 3 90 90 A3 18 1 8A 1E 2 85 83 6C 4 1 83 31 35 70 3 81 35 31
00:18:58:
00:18:58: ISDN BR0: Incoming call id = 0x000B, dsl 0
00:18:58: ISDN BR0: LIF_EVENT: ces/callid 1/0xB HOST_INCOMING_CALL
00:18:58: ISDN BR0: HOST_INCOMING_CALL: (non-POTS) VOICE
00:18:58: ISDN BR0: HOST_INCOMING_CALL: (1) call_type = VOICE
00:18:58: ISDN BR0: HOST_INCOMING_CALL: voice_answer_data = FALSE call type is VOICE ALAW
00:18:58: ISDN BR0: Event: Received a VOICE call from 15 on B2 at 64 Kb/s
00:18:58: ISDN BR0: Event: Accepting the call id 0xB
00:18:58: ISDN BR0: INCOMING CALL: VOICE ERROR: Bearer capability not available(0x3A): bchan 1, call id B
00:18:58: ISDN BR0: process_disconnect(): call id 0xB, call type is VOICE, b_idb 0x24F470, ces 1, cause Bearer capability not available(0x3A)
00:18:58: ISDN: get_isdn_service_state(): idb 0x24F470 bchan 3 is_isdn 1 Not a Pri
00:18:58: CCBRI_Go Fr Host InPkgInfo (Len=9) :
00:18:58: 7 0 1 0 B 3 18 1 8A
00:18:58:
00:18:58: CCBRI_Go Fr Host InPkgInfo (Len=13) :
00:18:58: 5 0 1 0 B 3 8 1 BA 8 2 80 BA
00:18:58:
00:18:58: ISDN BR0: TX -> CALL_PROC pd = 8 callref = 0x81
00:18:58: Channel ID i = 0x8A
00:18:58: ISDN BR0: TX -> DISCONNECT pd = 8 callref = 0x81
00:18:58: Cause i = 0x80BA - Bearer capability not available
00:18:58: ISDN BR0: RX <- RELEASE pd = 8 callref = 0x01
00:18:58: CCBRI_Go Fr L3 pkt (Len=4) :
00:18:58: 4D 1 81 97
00:18:58:
00:18:58: ISDN BR0: LIF_EVENT: ces/callid 1/0xB HOST_DISCONNECT_ACK
router-2503-II#
00:18:58: ISDN: get_isdn_service_state(): idb 0x24F470 bchan 3 is_isdn 1 Not a Pri
00:18:58: ISDN BR0: HOST_DISCONNECT_ACK: call type is VOICE
00:18:58: ISDN BR0: HOST_DISCONNECT_ACK: VOICE ERROR: Bearer capability not available(0x3A): bchan 1, call id B
00:18:58: ISDN BR0: TX -> RELEASE_COMP pd = 8 callref = 0x81
router-2503-II#
Does anyone know whats going wrong and why I could not get a connection th the 2503-II router? When I try the connection from an other router using isdn on both sides the connection works fine...
I added the configuration of both routers in the attachments...
Best Regards
Marcos

Hi,
I configured the ISDN BRI Intaerface on the Router-2503-II in the following manner:
router-2503-II#sh run int bri 0
Building configuration...
Current configuration : 133 bytes
interface BRI0
no ip address
encapsulation ppp
dialer pool-member 1
isdn switch-type basic-net3
isdn incoming-voice data
end
router-2503-II#
after this I tried it again and got the following debug output:
router-2503-II#
00:11:54: ISDN BR0: RX <- SETUP pd = 8 callref = 0x01
00:11:54: Bearer Capability i = 0x9090A3
00:11:54: Channel ID i = 0x8A
00:11:54: Progress Ind i = 0x8583 - Origination address is non-ISDN
00:11:54: Calling Party Number i = 0x01, 0x83, '15', Plan:ISDN, Type:Unknown
00:11:54: Called Party Number i = 0x81, '51', Plan:ISDN, Type:Unknown
00:11:54: CCBRI_Go Fr L3 pkt (Len=27) :
00:11:54: 5 1 81 90 4 3 90 90 A3 18 1 8A 1E 2 85 83 6C 4 1 83 31 35 70 3 81 35 31
00:11:54:
00:11:54: ISDN BR0: Incoming call id = 0x0008, dsl 0
00:11:54: ISDN BR0: LIF_EVENT: ces/callid 1/0x8 HOST_INCOMING_CALL
00:11:54: ISDN BR0: HOST_INCOMING_CALL: (non-POTS) VOICE
00:11:55: ISDN BR0: HOST_INCOMING_CALL: (1) call_type = VOICE
00:11:55: ISDN BR0: HOST_INCOMING_CALL: voice_answer_data = TRUE call type is VOICE ALAW
00:11:55: ISDN BR0: call id 0x8 call treated as DOV
00:11:55: ISDN BR0: Event: Received a DATA call from 15 on B2 at 64 Kb/s
00:11:55: ISDN BR0: Event: Accepting the call id 0x8
00:11:55: ISDN BR0:2: Incoming call rejected, unbindable
00:11:55: ISDN BR0: process_disconnect(): call id 0x8, call type is DATA, b_idb 0x24F470, ces 1, cause Call rejected(0x15)
00:11:55: ISDN: get_isdn_service_state(): idb 0x24F470 bchan 3 is_isdn 1 Not a Pri
router-2503-II#
00:11:55: ISDN BR0: HOST_INCOMING_CALL: DIALER ERROR 1: bchan 1, call id 8
00:11:55: CCBRI_Go Fr Host InPkgInfo (Len=13) :
00:11:55: 5 0 1 0 8 3 8 1 95 8 2 80 95
00:11:55:
00:11:55: ISDN BR0: LIF_EVENT: ces/callid 1/0x8 HOST_DISCONNECT_ACK
00:11:55: ISDN: get_isdn_service_state(): idb 0x24F470 bchan 3 is_isdn 1 Not a Pri
00:11:55: ISDN BR0: HOST_DISCONNECT_ACK: call type is VOICE
00:11:55: ISDN BR0: TX -> RELEASE_COMP pd = 8 callref = 0x81
00:11:55: Cause i = 0x8095 - Call rejected
router-2503-II#
Have you any ideas where to look from here?
Regards
Marcos

Similar Messages

I am having problem dialing from my iphoe 5 but I can receive calls and 3G is working

I have an Iphone IOS 8.2 , occasionly like every couple of weeks I am not able to dial from my phone , however I ahve no proble receiving incoming calls and 3G works fine without any interruption. So to temporalrly solve the problem I move the sim card from my Ipone and isnert it in my Ipad activiate 3g on my ipad and do soem brwsing then I move the sim card back to my phone and problem fixed , I can dial again. I woluld like to know what could be causing this problem so I can fix it once and for all

Greetings samuelfrombamako,
Welcome to the Apple Support Communities!
I understand that you have been having a sporadic issue where you cannot make an outgoing call. Removing the SIM card is a good troubleshooting step, although you shouldn’t need to place it in your iPad. There are a couple of other troubleshooting steps I would suggest because this is an ongoing issue such as Reset Network Settings which are outlined in the attached article.
If you can't make or receive calls on your iPhone - Apple Support
Cheers,
Joe

Problem Booting from an External Hardrive

Hi All,
I have a problem trying to boot from an external firewire hardrive. I have a iBook G4 running 10.4.8. and I'm trying to boot from an external firewire hardrive running 10.3.9. It will not boot. I get a grey screen with the international "No" sign (the circle with a diagonal line through it). But yet, I can take that same external firewire hardrive and hook it up to my iMac G4 running 10.4.8., and it boots up with no problem. Any help would be greatly appreciated. Thanks.
iBook G4 1.33 1.25GB RAM  iMac G4 1.25 2GB  iMac G4 800 1GB  iMac G3 600 1GB Mac OS X (10.4.8)

Here's an update. I think I figured it out. In the "get info" box of the external HDD, there is a checkbox at the bottom that reads, "Ignore ownership on this volume" and it was checked. So, I unchecked it, and rebooted, and now it boots up correctly. I'm not exactly sure what that checkbox means, but it's working now. Thanks to everyone for your input.

Booting from an external drive over usb

Hey, has anyone else had any problems booting from an external? I have an external lacie drive that I keep a clone backup on (using superduper) and usually have it connected with firewire400. I know it works because i've accidently booted using it before, but recently the firewire port on it died so i've been using usb instead.
Now the problem, holding option on my macbook starting, I get no options to choose from. If i have the mac osx dvd in, it pops up so I know it's not a problem with my macbook. It is possible to boot from usb correct? Everything i've read has said it's possible... I'm not sure why my external drive isn't coming up. I know it works over usb because I've used it alot since the firewire port died on it. I checked in the disk utility and it does say it's bootable, and afterall it's cloned using superduper like i said before...
I have 2 partitions on the drive, is that a problem? It never was before, I've booted off it many times before using firewire though. Can someone help me out here? Very annoying as I'm replacing the HD in my macbook and neeeeeeed to get on my external.
When I asked the guy at the genius bar awhile ago he just said it was probably a problem because my old internal HD died and he said sometimes it causes the macbook to not even be able to get as far as the point to boot from another source. Well now I have a new working drive in it, so I know that's not the problem. It just doesn't show up to boot from anymore, ugh.

Sounds like your clone isn't bootable. Have you tried the following:
Repairing the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger and Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer. Now restart normally.
If DU reports errors it cannot fix, then you will need Disk Warrior (4.0 for Tiger, and 4.1 for Leopard) and/or TechTool Pro (4.6.1 for Leopard) to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.

Nokia C7 Dialing from contact list

I'm having problem dialing from contact list and recent calls. I can only makes calls when dialing the numbers. I can receive calls. Texting works fine from contact list and recent calls, but voice call can only be done by dialing the number .Phone has to reboot everytime it happens.

Hi Remembranze,
First of all, check via Nokia Suite and on the phone itself for any firmware updates that may be available. IF there is an update, please update to the latest version offered. If there is no update, then try re-installing your current firmware via Nokia Suite. Failing this, try Restoring your phone to factory settings, and if this doesn't work, then you try performing a three finger hard reset. Failing this, you will need to take your phone to your local Nokia Care point for them to inspect.
to locate your nearest Nokia Care point: http://nokia.com/support

Problem booting from Hdd

I have a problem booting from a external Hdd comes up with a command screen then a box with shutdown then restart any ideas

There must be something wrong with the data on the drive or it's hardware as you are experiencing a Kernel Panic. Run a repair on it maybe?
DALE

Having lag problems on the XBOX 360 - connecting to WRT160N wireless router.

Having lag problems when playing on the XBOX 360(wireless connection) after we installed our new WRT160N wireless router. Looking for ideals on how to fix this performance problem?
Cable Conpany: Comcast
Modem Model: zoom
Wireless Router Model: Linksys WRT160N

A few more thoughts:
- Changing the channel settings does NOT achieve anything. I manually tried every setting with no success.
- Changing the encryption settings did not help. I tried "open", WEP and WPA and none of them work.
- Even when this problem shows up, the xbox360 wireless adapter successfully finds and associates with the wireless network. It even manages to read data from the network - it just does it VERY SLOWLY and disconnects often. This causes extreme lag in xbox live games, which shows up as unpredictable play and disconnects from games.
- The fact that G-only mode works fine pretty much proves that this problem can be fixed with a firmware change. The xbox360 wireless adapter and the WRT160N can definately talk to each other using 802.11g successfully so there must be some issue with negotiating the correct version of 802.11x.
- I've considered trying a third-party firmware, such as DD-WRT to see if this fixes the problem. Has anyone tried this and if so what happened?
If you are seeing this problem, please reply to this thread and say so. If enough people respond perhaps Linksys will fix the problem. Even if you're not registered with this board, registering is very quick and easy so don't let that deter you.
Thanks

10.5.2 and Apple External Modem Dialup - computer freezes when dialing up

Hi,
Many thanks in advance for your attention.
Since upgrading to OS 10.5.2, the computer freezes (the cursor freezes) each time I try to dial up to internet. The only way to unlock computer is to shut the power button off and start over.
I am using the Apple External Modem.
Had no problems before (10.5.1, 10.5, Tiger, etc.). So far I seemingly have no problems with any other app. Only when I try to connect (dialup) to the internet.
I did the usual repair and verify permissions before and after installation.
I did a repair and verify Disc (from the Install Disc) after these problems.
Both reported no problems.
I also tried trashing Internet Connect prefs files in Home Library.
I see a lot of posts and looks for Wireless connection problems.
The only dialup solution I've read so far are people who went back to 10.5.1.
- Ross

Ross Corsair wrote:
Hi,
Found this as a suggestion on how to fix the 10.5.2 internet dialup problem, but it is so vaguely written, I have no idea what the tipster is talking about.
I assume the tipster means one types these commands in Terminal?
If someone can explain the following in English, I would be grateful.
I had problems sharing a dial-up (Modem) PPP connection. I want to use NAT for security reasons and found that only the first connection after reboot worked. Subsequent connects would fail due to NATD not rebinding the new PPP bindings. Restarting NATD fixed the problem. Luckily PPPD fires off some scripts in /etc/ppp depending on connection status. The following script restarts NATD after every successfull connect if you save it as /etc/ppp/ip-up (don't forget to make it executable):
#!/bin/sh -
N_P=`ps -uxc -U root | grep ' natd$' | awk '{ print $2 }'`
if [ "$N_P" != "" ]; then
logger -i -t $0 "Sending SIGHUP to natd (PID $N_P)"
kill -HUP $N_P
fi
Yes, this meant to be run in the terminal.
Really, the poster expected that these commands would be saved in a sh script and executed that way.
Create a txt file and past those commands into it. It will need to be saved with execution permissions.
What does it do?
N_P=`ps -uxc -U root | grep ' natd$' | awk '{ print $2 }'`
This asks the system for a list of running processes (ps -uxc) where the user is root (system admin) and passes this list to grep (which filters the list looking for a process with the string 'natd$'. This passes a single line out of the process list to awk which simply prints the second item in the list.
The end result is that the procid (process id) for the natd process is stored in the variable N_P.
Next -
if [ "$N_P" != "" ]; then
logger -i -t $0 "Sending SIGHUP to natd (PID $N_P)"
kill -HUP $N_P
fi
This checks whether a natd process was found - $N_P not null string.
If a process was found - the logger command writes and entry to the system log and then the script tries to kill the process gently (kill -HUP).
This should clear the natd process which should restart if you try and dial again.
The script is not really vague - just needs a comment or two to make it understandable to those who are not Unix geeks.

[URGENT] Problems Booting from External HD

I'm at a complete loss on this one. I'm a pretty competent Mac geek, and even I can't figure this out. Bear with me, I'll try and explain my problem as best I can. First, some basic info:
My hardware setup:
• iMac G3 600MHz
• 1GB RAM
• 120GB internal HD, running OSX 10.4.7
The computer's internal drive is used by someone else for work during the day. I run all of my files and programs from a 2nd HD, which I boot from:
• Seagate 300GB HD
• Bytecc combo USB/Firewire drive enclosure
Software:
The only recent install I've done is Super Duper, which I did after I began having problems. I used it clone my Firewire boot drive to a (backup) 400GB external USB/Firewire drive, and I restored from the clone once when I began having the problems that now appear to have come back. At the time, it appeared that restoring from the clone had solved my problems. I'm fairly certain that my problems are software-related: I've installed the drive in question in another Mac (internally), S.M.A.R.T. status appears fine. I'm not using anything awful like Norton Disk Doctor, I've tried rebuilding the volume using DiskWarrior, without success.
Problem:
I am unable to boot from my Firewire drive. When I start up using it, everything appears normal, until I get to the boot panel. The progress bar loads very slowly, and only gets about halfway finished before the login panel appears on top of it (even though the boot drive is a single-user volume, set to login automatically). The username and password fields are both blank, and if I enter my username and password it says it's incorrect.
Symptoms:
• OSX/programs become unresponsive after waking from sleep. Computer freezes, and most recently the screen went completely gray. After forceably turning off the computer and HD and restarting, I get the problem I just mentioned with the login panel. I don't have any problems waking from sleep if I'm booting from the computer's internal HD.
• Certain programs (notably iTunes and Adobe CS2 apps) periodically become unresponsive and quit. Several times I've gotten an "unknown error" message from iTunes saying that it is "unable to save the iTunes library". Both of these issues usually precede the main problem of being unable to boot/login.
• Occasionally, if I boot from the computer's internal HD and then switch on the external, it refuses to recognize it as being a formatted OSX extended (journaled) volume. Turning it off for several minutes and then turning it back on sometimes fixes it, as does repairing it using Disk Utility.
These problems have been plaguing me for months now, and with more than one external HD (although using the same enclosure). Everytime I do something to fix it, the problems seem to go away for an increasingly shorter amount of time, before reappearing, each time slightly worse than before. I'm convinced all of the issues I've been having are in some way related, I just can't figure out how they're related (or what I can do to fix them). Hopefully, one of you can help me.
iMac G3 600MHz Mac OS X (10.4.7) 1GB RAM | 120GB HD (Internal) | 300GB HD (External) | 400GB HD (External)

I occassionally get a similar problem, when playing a corrupt video via mplayer. The scrren freezes and I have to poweroff. When I log back in no user and no password is valid, even when root is enabled.
Solution: replace from a cloan. You will need to boot from a good cloan before you can do this, and be able to retain the original permissions.
I use: sudo rsync -avE /private/var/db/netinfo/ /Volumes/vol-name/private/var/db/netinfo
PB 15 1.5 Ghz

Read data from an external Oracle-DB: Codepage problems

Hi,
I try to get data from an external Oracle-DB which runs under NLS_CHARACTER
WE8ISO8859P1. In this DB are russian texte stored. If I read these texts via native-SQL I obviously get wrong characters. (e.g. Èíñòðóìåíòû äëÿ óãëîâîé øëèôîâàëüíîé ìàøèíû instead of Инструменты для угловой шлифовальной машины). If I save the text as a html file and then open it with IE. I can change the encoding and get the right view.
Has anybody got an idea ? (Mabye I can read the data in a different codepage or maybe there is a possibility to convert the codepage in SAP after reading it from oracle)
Thanks a lot !!!!

The problem is solved.
Many thanks !

I have a macbook pro from 2006, my internal cd drive is not working and i'm trying to install factory definitions from an external cd drive. the problem is that when i press c nothing happens only appears an interrogation folder.

i have a macbook pro from 2006, my internal cd drive is not working and i'm trying to install factory definitions from an external cd drive. the problem is that when i press c nothing happens only appears an interrogation folder. or sometimes appears the apple logo and than back again to the interrogation folder... Help please!!!!

mcbsousa wrote:
hm... Is there any chance of making the bootable usb file and send it by dropbox or something like that? than put it in a pen drive and connect to the mac??
Sending by Dropbox where, To who, to what computer? As your does not start up.
You need to take at least the OS disc to a work Mac computer and create DMG from the OS install disc then restore that DMG to USB thumb drive. Then you can boot the computer from that thumb drive and install the OS. That is if your hard drive is functioning correctly.
Then you can use the App disc in the external CD/DVD drive to load up all the included Applications that come with your version of OS X.

Problems importing and playing songs from an external cd/dvd drive

I am having problems importing songs on my PC from an external usb drive. What I have is an external combo usb firewire drive hooked up to my pc with a usb cable. (usb 2.0) When I launch itunes, it sees the cd I have loaded but when I go to import the songs, itunes just pops past each song in a second like each song was just a second in length. Then I have some corrupt file in my itunes library. Itunes gets the cd names and titles from CDDB correctly but can't play the songs or import them. I use this pc solely for playing audio, it is a Pentium 4 2.6 with 1GB of ram with build in usb 2.0 on the motherboard. There is no other software installed on the system other then virus software. When I use Windows Media Player the cd is read perfectly fine. I even play DVDs off the drive with no problems too. This problem in intermittent, with different cds. These are all commercial cds not burnt ones that someone made for me. Any help or suggestions would be appreciated.

Hi Toonz - I have exactly the same problem when trying to import songs - itunes does recognise the cd drive and names of tracks etc - it just won't play more than one second of each, or import any more. i did run the cd diagnostic check you suggested - results below - don't mean anything to me i'm afraid - any bright ideas?
this was a christmas present and i haven't managed to put any new music on apart from what was already on our pc, so am v sad and hope you can make it better....
Microsoft Windows XP Home Edition Service Pack 2 (Build 2600)
ASUSTeK Computer INC. A7N8X2.0
iTunes 6.0.0.18
CD Driver 2.0.4.3
CD Driver DLL 2.0.3.2
UpperFilters: GEARAspiWDM (2.0.4.3),
Video Driver: RADEON 9500\RADEON 9500
IDE\DiskMaxtor6Y120P0_________________________YAR41BW0, Bus Type ATA, Bus Address [0,0]
IDE\CdRomATAPICD-RW_52XMax______________________150D___, Bus Type ATA, Bus Address [1,0]
IDE\CdRomSONYDVD-ROM_DDU1612____________________DYS1___, Bus Type ATA, Bus Address [0,0]
If you have multiple drives on the same IDE or SCSI bus, these drives may interfere with each other.
Some computers need an update to the ATA or IDE bus driver, or Intel chipset. If iTunes has problems recognizing CDs or hanging or crashing while importing or burning CDs, check the support site for the manufacturer of your computer or motherboard.
Current user is administrator.
D: SONY DVD-ROM DDU1612, Rev DYS1
Drive is empty.
E: ATAPI CD-RW 52XMax, Rev 150D
Audio CD in drive.
Found 14 songs on CD, playing time 65:08 on Audio CD.
Track 1, start time 00:02:00
Track 2, start time 00:17:42
Track 3, start time 04:59:28
Track 4, start time 12:35:43
Track 5, start time 16:11:73
Track 6, start time 22:46:73
Track 7, start time 28:23:27
Track 8, start time 32:37:70
Track 9, start time 37:46:01
Track 10, start time 42:35:14
Track 11, start time 46:22:32
Track 12, start time 50:29:14
Track 13, start time 55:20:60
Track 14, start time 60:46:54
Audio CD reading failed. Error Code: 1110 1110 1110 1110 1110 1110 1110 1110 1110 1110 1110 1110 1110 1110 1110 1110 1110 1110 1110 1110.
Get drive speed succeeded.
The drive CDR speeds are: 4 8 12 16 20 24 32 40 48 52.
The drive CDRW speeds are: 4.

Dial up Connection using External Modem in Solaris Intel Version

Hi
How to Install a modem in Solaris 7 Intel version and how to make a Dial Up Connection Using this external Modem.
Can any one Help me....
send your reply to [email protected]
Thanks in Advance ....
Vinod.

hello
i'm fond that inside the folder /etc you have another one called /ppp and inside the folder /ppp you have some files that you have to edit in orther to configure your user name and password, but everything is explained on that files, and is bether that you reed then
then in the console you have to type pppd ttya (if your modem is conected to the Com1) call myisp
were myisp is one of the files that you have to configure, but how i'm told you everyting is splained on that files
If you dont have it please install the 2 Cd
the only thing that i'm can't configure was diseble the "wait for dial tone" and in order of that i'm not able to conect to the internet, if you now someting aoubt that please send a e-mail to [email protected]
tanks

Flash CC Air iOS: Problems with loading text from an external xml located on a server.

So I have this code allowing me to load text from an xml located on a server. Everything works fine on the Air for Android. The app even works in the ios emulator, but once I export my app to my ios device with ios 7, I don't see any text. The app is developed with Air sdk 3.9. What could be the reason? Do I need any special permissions like on Android? Does ios even allow to load xml from an external server?
Any clues?

It was my bad. I linked to a php file to avoid any connection lags, which was absolutely fine on the android, but didn't seem to work on the ios 7. So all I did is change the php extension to xml and it worked without any problems.

Problems deleting a string from an external file.

hi!
I am working on a program but am having problems deleting a string of information from an external file. The code I have managed to do only seems to be deleting the surname. The rest of the string remains and the Surname from the string bellow the one that should have been deleted moves to where the surname that was just deleated was.
this is the code snippet that should be deleting the string:
          System.out.print("Please enter the last name of the contact: ");
          last_name = dataInput.next();
          int z = 0;
          for (int i=0; i < number_of_records; i++)
                    if ((last_name.compareTo(lastName)) < i && (last_name.compareTo(lastName[i]) > i))
                              z = i;
          for (int i = z; i < number_of_records; i++)
                    lastName[i] = lastName[i+1];
Anyone got any ideas why its not deleting the whole string?
the extrenal file is set out like:
surname,,first name,,phone number

I don't think you have given enough information to answer this question completely; however, here is my guess:
The code that appears to be doing the "deleting"
for (int i = z; i < number_of_records; i++)
    lastName[i] = lastName[i+1];
}is only acting upon the lastName array.

Problems dialing from a external modem to a isdn router

Similar Messages

Maybe you are looking for