Recording stops and starts up again

So i was recording a gig and it would stop and start up again throughout
the event. I was not running anything else on my laptop but onlocation. My virus protection was turned
off since I was in a non-wifi location.
Here are my specs for my laptop.
HP-HDX18
Intel(R) Core(TM) 2 Duo CPU
T9900 @ 3.06 GHz-3.07GHz
Memory 6GB
64 Bit Windows Vista - Waiting for my Windows 7 upgrade to come in.
500 GB HD
Rating of 5.4

When I first tried it out... it was a band new laptop. Nothing was running
on it except on location. I turned off the screen saver and virus
protection. There was no pattern of when it would glitch it would just do
it. Some a few seconds apart to a few minutes apart. Yes my disk very
defragmented which I always do after installing and uninstalling programs.
So I know everything was up to par at that time. I also have premiere pro
cs4 on it and it runs fine with no hiccups. Just on location does this. I
kind of notice at one time it seemed like it would hiccup when the audio
level dropped. But then again it would do it when someone was on the mic
talking too. So I'm clueless... and I believe its going to be very hard to
diagnose.

Similar Messages

Airplay movie stops and start over again

I have problem with AirPlay while watching play-channels from my iPad. After a while the program just starts over again. What can I do to fix this?

Welcome to the Apple Community.
Intermittent problems are often a result of interference. Interference can be caused by other networks in the neighbourhood or from household electrical items.
You can download and install iStumbler (NetStumbler for windows users) to help you see which channels are used by neighbouring networks so that you can avoid them, but iStumbler will not see household items.
Refer to your router manual for instructions on changing your wifi channel or adjusting your multicast rate.
There are other types of problems that can affect networks, but this is by far the most common, hence worth mentioning first. Networks that have inherent issues can be seen to work differently with different versions of the same software. You might also try moving the Apple TV away from other electrical equipment.

HT201412 my new ipod touch 5 will not turn on!!! im mad about this can someone helpp me or tell me what to do i tried alot of stuff my ipod just has the spinning circle it will turn on but 5 seconds later it stops and starts spinning again.

So today I try to reset my Ipod. But it doesnt work!!! It will turn on for about 5 seconds then shut down and the spinning circle will appear. I tried resetting, but it didnt work. someone please help me before I break this thing!!!!

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

How can I stop the execution on a JSP page and start it again

Hi
I am making a program that simulates how to manage transactions when accessing a database by using locks. I have run into a problem and I hope someone has the time to help me.
When a user does an update the transaction commits and releases its locks when the program executes
<%stmt.executeUpdate("commit!"); %>
I need to put a break in to stop the program executing this statement, to illustrate the lock is set correctly.
I have tried to put in an alert box but this does not prevent the rest of the java code being executed.
I have tried to use prompt boxes, JavaScript functions, but these functions cannot have any java code in them.
I have tried using the java.swing JOptionPane boxes but this didn?t work either
I have tried to get input from the user but I don?t know how to retrieve this data on the same page. (As far as I know you have to use submit and even refresh the page or retrieve it on the next page).
Does anyone know how I can stop the execution on a JSP page and start it again (on same page)
Mette

I already have another client (Tomcat jsp application) running and it throws a SQLException correctly when I don�t put in a commit=true statement and don't close the database connection.
But the problem is how to get the code above to stop to illustrate I have set this lock.
I have tried to use the JOptionPane but because my program is running in a web browser I cannot use the JOptionPane dialog box.
I have tired using an alert box but it executes the commit statement before the alert box is dispayed. So this does not work
While (i < 2)
if( i==1)
%>alert(�The transactions commits when you press Ok�); <% //what it to stop execution here
else
stmt.executeUpdate(�commit�);
I am not using threads so I cannot use the sleep function.
I am using mysql and have already configured it to detect deadlocks and how long to wait for locks.
Thanks for your help
Mette

Has anyone else experienced the stopping and starting again while playing music in iTunes. It was fixed but with the last update it has started skipping again.

Has anyone else experienced the stopping and starting again whil playing music in itunes. It was working fine wit the prior fix, but after the last update
it started skipping again.

Try it in another vehicle see if it still happens, at least you can narrow it down to your phone or the car. My 4s play totally fine, I have never had any of those issues. Maybe its time to restore your phone and start over. I would also have someone else play their Iphone in your car, see if it happens to them. Or try yours in someone elses car. Good Luck!

Why does Image Capture stop recognizing Epson scanner after scanning several images? I have to stop and start the scanner in order for Image Capture to recognize it again.

Why does Image Capture stop recognizing Epson scanner after scanning several images? I have to stop and start the scanner in order for Image Capture to recognize it again.

Karen ...
Might be corrupted preferences (.plist)
Open the Finder. From the Finder menu bar click Go > Go to Folder
Type or copy paste the following:
~/Library/Preferences/com.apple.image_Capture.plist
Click Go then move the com.apple.image_Capture.plist file to the Trash.
Restart your Mac and your scanner and try scanning an image.

Everytime I try to start FaceTime it says: "There has occured a problem with FaceTime. You have to stop FaceTime and start it again" What can I do about this?

Everytime I try to start FaceTime it says: "There has occured a problem with FaceTime. You have to stop FaceTime and start it again" What can I do about this?

Same problem as well as the network failure. Apple Care was suggesting a full reinstall and I declined. I thought it worked once but I can't be sure ... it might have been Skype which works perfectly.

I have Macbook Air. One day i am using email-Entrouage, sudden it stuck up. I stopped it and start entourage again but it start verify and and rebuild but not rebuilt. email are 41.5 GB and free 5 GB, plesae guide how to resovle.

i have Macbook Air. One day i am using email-Entrouage, sudden it stuck up. I stopped it and start entourage again but it start verify and and rebuild but not rebuilt. email are 41.5 GB and free 5 GB. When problem not resolved i also copied that email db file in other Mac book with 200 GB free space but same process first verify then rebuild then message it cannot rebuild. Please guide.

I've been rebuilding Entourage Identities for years for clients. Most fail because they do not have enough free space. See this article
http://www.officeformachelp.com/2007/09/rebuilding_a_damaged_database_that_excee ded_size_limit/
(Fair disclosure: OfficeforMacHelp is my site. I may receive some form of compensation, financial or otherwise, from my recommendation or link.)

What will happen if oracle listener is stopped and started again.....

Hi Gurus,
Please suggest What will happen if oracle listener is stopped and started again on a running SAP System ?
Thanks in advance.

Hi Lakhbir,
What will happen is that, all SAP work processes will loose connection to the database.
If any active jobs(background jobs, updates, insert to database ) are running, they may fail. All the work processes will go to a re-connect state.
( There are few notes on WP reconnect which you can check and read about)
DB Reconnect Parameters - SAP High Availability - SAP Library
Application will be running but users will not be able to do any activity or may not be able to login at all and may get errors like ( No connect to database possible)
As soon as you start the listener process again , all the work processes will connect to the database again.
This is because the WPs will keep on trying to connect to database at regular interval and as soon as the connection is available they will re-connect.
You do not have to restart any work process manually in SM50 or anywhere else as this feature is enabled by default until disabled manually.
Thanks
Amit

Sound stops and starts with x-fi titanium pci e

I am going nuts with this problem and creative support is not much help atm, so I have been troubleshooting myself. Whats going on is my sound stops, starts, and stutters a lot. It is pretty bad when I play music files but it is absolutely horrible when I watch videos like on CNN or YOU TUBE. It is like a old vinyl record skipping, except when this gets off a stutter, it races to where it should be on the time line. Also my creative console does not work right. I cannot use the equalizer, as the custom, rock, pop music select is greyed out and the box is checked to use the equlaizer. It also disappears when I click on a few tabs, like between speakers, bass, equalizer..then its just gone and I have to click the shortcut again to get it back.
What I have done so far is un-install everything, and do a clean boot, then re-install and I have the same problems. Though I downloaded the creative console beta(2.6.49) and it seemed to have fixed my issues with that. But downloading the new drivers (2.7.8) does not fix the stopping and starting.
Any suggestions?
I should mention I use klipsitch speakers..2.1, I don't have surround sound anymore.
Customer service had me run a registry cleaner and use it to uninstall everything creative. I used CCleaner, then used direct links to download drivers...again...(2.7.8) and a creative console(2.6.35)..guess what? It didn't work, same problems, though I downloaded and re-installed the beta for the creative console(2.6.49) and now it works fine. I also did all this under a clean boot..again.

Check if "Play Stereo Mix using Digital Output" is checked in the Console launcher in Settings/Digital IO.

SSRS Report queries begin running slowly, have to stop and start report server to restore performance

We have had a production issue crop up twice now where reports begin running slowly seemingly at random.
When this happens we can see from running SQL Profiler that the report queries are taking an extremely long time to execute. The same queries when run directly in management studio run quickly.
Initially I suspected parameter sniffing, and tried using OPTION (RECOMPILE) in the reports, as well as clearing out the particular query from the plan cache and running the SQL in SSMS to try and get a better plan etc but no amount of jiggery pokery by
me could get the queries to run any faster.
The really weird thing - is that stopping and starting the report server via the reporting services configuration manager instantly cures the problem.
I'd really love to know - why this might be? Is it something to do with the report server closing and re-opening its connections to the database? That's the only sort of thing I can think of...any ideas? Anyone? Any suggestions would be much appreciated.
LucasF

Hi LucasF,
In your scenario, usually we can monitor the execution log in Report Database. If you run below query, you can get the results how long the report takes to render (TimeRendering), how long to process the report(TimeProcessing) and how long to retrieve data
from Database(TimeData). You can check the starttime and endtime to know the total time for executing a report.
SELECT TOP1000 *FROM[ReportServer].[dbo].[ExecutionLog2]
More details information, please reference to similar thread below:
Steps for troubleshooting a slow SSRS 2014 server
Troubleshooting Reports: Report Performance
In SQL Server Reporting Services, a job will be created by SQL Server Agent if any of the following processes is underway:
query execution on a remote or local database server
report processing
report rendering
To cancel a job that is running on the report server, we can cancel the job directly or reduce the report execution time-out value in the SQL Server Management Studio and then will stop query execution. Please refer to the steps below:
Open SQL Server Management Studio, and connect to "Reporting Services".
Under the Report Server node, right-click on the "Jobs" folder and select "Refresh". Then, right-click on "Jobs" again and click "Cancel All Jobs".
Right-click on the Report Server node and open the "Server Properties" dialog.
Click the "Execution" option, and set the "Limit report execution to the following number of seconds:" to a much smaller number. After this issue is resolved, this configuration should revert to the previous state.
Reference:
Managing a Running Process
Setting Time-out Values for Report and Shared Dataset Processing
In addition, we can also use the KILL Transact-SQL statement to terminate a normal connection by terminating the transactions that are associated with the specified session ID. For the details information, you can refer to:
KILL (Transact-SQL)
If you still have any problem, please feel free to ask.
Regards,
Vicky Liu
Vicky Liu
TechNet Community Support

DVD will not stop and start in a Menue Mode

Hello I am using DVD Studio Pro 4 for a school project and i am looking for some help with this problem.
The DVD i have created plays and stops when i am watching one of my video tracks, i just can not start the DVD when i am previewing in any menue after i stop it.
I have created my DVD with 16 menus and 2 video tracks. It burns and plays back fine but i can not stop and start the DVD when i am in a menu mode. The DVD will stop and play when i stop the DVD playing video from one of my video tracks but when i am in menu i push stop on my DVD controller and the DVD will not start back up. The DVD will look like it wants to play but it will not play. I have to open the DVD player tray open in order for it to start the DVD again.
The DVD is a NTSC, SD, single layered 2.9GB
Any help would be much appreciated, Thanks.
Mike
PowerBook G4 15 1.25 ghz Mac OS X (10.3.9)

If only five months old it is still under warranty. Take it back.

Simple question? - stop and start code

hi, can anyone tell me how to stop this code and then start it again, as all it dose now is move to the last instruction. the code is on an action of a button being pressed, i would like it to stop in the code were it stays stop and then continue again when the button that it is on is pressed.
               board.setImage(0, 2, im); // move counter
               board.setImage(0, 1, null); // removing the last counter
               //stop
               board.setImage(0, 4, im); // move counter
               board.setImage(0, 3, null); // removing the last counter
                Is there any way of doing this?

helen852008 wrote:
hi, can anyone tell me how to stop this code and then start it again, as all it dose now is move to the last instruction. I'm guessing that you're trying to do some CPU-intensive animation processing on the EDT (event dispatch thread). You probably need to do some of your labor-intensive processing in a background worker thread. A SwingWorker object might work well for you. If you look at the api for this and search the forum you'll get an idea on what it does and some sample code. If this doesn't help, then you may do well to post a compilable subsection of your code, or SSCCE. Read up on posting SSCCEs here:
http://homepage1.nifty.com/algafield/sscce.html

Have to Stop and start "Apple Mobile Device EVERY time

I have an iPad and an iPod which I sync every morning through iTunes with Outlook. And each morning I must stop and start "Apple mobile device" in the Services to get iTunes to recognize my devices.
I have recently uninstalled iTunes,QuickTime, Bonjour.................................and reinstalled the latest version of iTunes and the latest versions for my iPad and iPod.
Nothing has changed. Any other advice.

Apple Mobile Device not Starting
· Windows Vista or Windows 7
In the Start SearchServices.
In the Programs
Select Apple Mobile DeviceStop the service
After the service has stopped, click Start the service.
After the Apple Mobile Device service has started again, open iTunes and connect the device.

How to stop and start only the process of Oracle Application Express?

I'd like to know how to stop the process of Oracle Application Express on my server installed oracle express package.
After installed Oracle Express edition, not only oracle database server processes but also Oracle Application Express, such as http server, is started automatically...
I hope to stop and start Application Express on demand but is this feature enabled?

Oracle Apex is an API, if that helps you understand / visualize. You do not start Apex process nor stop it.
When an Apex session starts it starts calling the API.
You can however start / stop the listener. It may be OHS, ApexListener and the J2EE container running it, OC4J or any other "server" that you are using.
The built-in EPG is something like an API again, you cannot start / stop it but you can disable/enable it with DBMS_XDB.SETHTTPPORT API.
Regards,

Recording stops and starts up again

Similar Messages

Maybe you are looking for