Satellite A300D-135 - BIOS - System Configuration Data Read Error

After Booting a Satellite A300D-135 laptop the following error message appears:
<Several BIOS messages >
3070M Extended RAM Passed
512 KB L2 Cache
System BIOS shadowed
Video BIOS shadowed
ATAPI CD-ROM: TSSTcorp CDDVDW TS-L632H
Fixed Disk 0: TOSHIBA MK2546GSX
Mouse initialized
ERROR
System Configuration Data Read Error
Press <F1> to resume, <F2> to Setup
After pressing F1 the machine boots Windows just fine, but the error message is quite irritating while it comes with a loud BEEP
I've tried the following things so far (in this particular order):
- Loaded BIOS defaults
- Flashed the BIOS with latest BIOS (2.80) for this model type
- Reinstalled windows with HDD format
All of these haven't worked.
I've seen the same message appearing on several places on the internet (on different laptops with a Phoenix BIOS in common), but until now I haven't been able to find a working solution.
It might me a hardware issue, but all devices (vga, soiund, lan, wifi, usb, hdd) seem to work just fine in Windows, so this doesn't seem the issue). Another solution that is mentioned in some forums is replacing the cell battery. But because the laptop keeps time properly I don't think this is the case either.
Any ideas ?
Regards,
GJ

Hi buddy,
It seems that the power on self test has detected a hardware error... :(
I think such a problem like this you cant solve with loading the default settings in BIOS or with an update because its hardware based error.
In your case I would contact an authorized service provider. The guys can check your notebook because they have special diagnostic tools for Toshiba notebooks and access to all Toshiba databases I think.
You can find a list of them here:
http://eu.computers.toshiba-europe.com > Support & Downloads > Find an authorized service provider
Usually they work really fast and you will have a short repair time I think. In my case it did take only one week until I got my notebook back. :)

Similar Messages

Pantone W530 Color Sensor help needed eccm25sensorData.dat read error

New Benzel installed to fix a bad track pad
On restart color sensor demanded re-calibration.
Error 22 message said ECCM25sensorData.dat file had a read error.
I can not locate file to install.
The Lenovo paid support solution was to suggest a full re install.!!
That is nuts, kind of like replacing a car engine because of a bad spark plug.
Anyone have a clue or work around?
And yes I tried unistalling and reinstalling the following: http://support.lenovo.com/us/en/downloads/ds015010
I get three buzz error when try initial calibration which then instructs to use the Sensor Replacement Utility which results in the error message.
Seem Windows 8 folks are having the same problem. What is up Lenovo??????????
http://forums.lenovo.com/t5/W-Series-ThinkPad-Laptops/windows-8-pantone-driver/m-p/1034813#U1034813
Windows 7 machine
Thanks!

"AMT Options" missing from HP 2540p BIOS "System Configuration" tab

I used to have an HP Elitebook 2540p Core i5. I recently got a Core i7 version.
The old machine had an "AMT Options" tab that could be used to set options to make it possible to see the AMT MEBx (Management Engine BIOS Extension) at boot time. This is shown in this picture:
My new Core i7 machine is missing this option, as shown here:
I need this option so I can enable the AMT serial-over-lan feature for debugging.
I updated my BIOS from F09 to F50 (the newest) but the option didn't appear. I went to the "Set Security Level" setting which seems to control what stuff is shown and what isn't. But it didn't have an AMT Options option.
Can anyone tell me how to get this option back? All HP Elitebook 2540p should support AMT right? Because this manual seems to indicate it:
http://h10032.www1.hp.com/ctg/Manual/c02958196.pdf
I also tried doing "Restore Defaults" and "Reset BIOS security to factory default" froim the "File" tab in the BIOS
(Also I tried just hitting ctrl-p repeatedly at boot to try and get into the MEBx but it didn't work
Thanks for any help you can provide (but I know this is a pretty hard/uncommon question)
Jimmy Dean

@jamesdeanthree
‎Thank you for using HP Support Forum. I have brought your issue to the appropriate team within HP. They will likely request information from you in order to look up your case details or product serial number. Please look for a private message from an identified HP contact. Additionally, keep in mind not to publicly post ( serial numbers and case details).
If you are unfamiliar with the Forum's private messaging please click here to learn more.
Thank you,
Omar
I Work for HP

Satellite Pro U200 - Bad Checksum (ROM (Data Block) ) error

Hello when i start my Toahiba Satellite Pro U200
I have a Error
Bad Checksum (ROM (Data Block) )
PRESS ANY KEY TO CONINUE.
Pleas Help

The most common cause for "Bad Checksum" errors is the CMOS battery malfunction on the motherboard.
The battery could be empty or could simply be dead. But its really not easy to say whats wrong exactly!
Therefore I would recommend firstly to access the BIOS and to set it to default settings. Dont forget to save the changes.
Furthermore you should connect the AC adaptor and should let it connected for about 24hours to recharge the CMOS battery.
Maybe it helps to get rid of this error message.
If it doesnt help, then you should contact a notebook technician!

LSMW data Reading Error

HI,
In the LSMW process i am getting the below error while doing 9th step Reading data.
Unable to write to file 'E:\Z1XK01_ZXK01_ZXK01.lsmw.read'
Message no. /SAPDMC/LSMW804
Rgds
Mani

'E:\Z1XK01_ZXK01_ZXK01.lsmw.read'
what is E: ?
only a directory on your application server is allowed here (it must not be a directory from presentation server, which is your local PC(
go back into step 7 and correct the directory and file name for the read data

MAnaged system configuration error in solution manager

Hi,
While doing managed system configuration getting the error, below versions are using.
MDM 7.1 SP10 Import server and Solution manager 7.1 SP10.
Can anyone help me?.
Regards
Chandra

Two cases you have
1) Satellite system
Re-install The DIA agent and give correct (port numbers )SLD details
Once you re-install the DIA agent, run Rz70 from satellite system
data will pull from satellite system to central SLD.
2)Run SLD check from Solman system , check its successful or not
Go to LMDB and check satellite system
After re-Synchronize technical system from SLD
Thanks ,
Rahul yedapally

EPM System Configurator Error

Hi,
I am trying to open EPM System Configurator but getting error:
"The Vital Product Data registry is in use by another installer. Please start this installer after the other installtion is complete."
I am not installing the EPM system. It is already installed. I am just trying to open EPM System Configurator by Start--All Programs--EPM System--Foundation Services-- Start EPM System Configurator
I am not running any othe installer. I tried restarting the system also but again I am getting the same error.
Please help me with this error.
Thanks & Regards,
Akshat

Hi Srikanth,
I am not running any othe installer. I tried restarting the system also but again I am getting the same error.
Actually I am trying to integrate OBIEE with EPM workspace.
I am following the below link:
http://download.oracle.com/docs/cd/E10415_01/doc/bi.1013/e10416/general_10134.htm?bcsi_scan_6E125C62D30562F9=0&bcsi_scan_filename=general_10134.htm#BEHGEFEI
I am facing the problem at step -- 11.5.3.6 Configuring the Web Server for EPM Workspace
Regards,
Akshat
Edited by: user10943765 on Oct 1, 2010 10:57 PM

Managed System Configuration - Software version and OS is not accepting

Dear
When i try to setup the PI system in solman 7.1 - Managed system configuration, below the error msg.
Please help to sort it the problem
Regards
Jay

Hi Pany,
Steps to follow
- Rename the J2EEFRMW01_5-20002637.zip file to J2EEFRMW01_5-20002637.SCA.
-telnet localhost 5$$08
-logon with the user administrator
- deploy /software/j2eefrmwpatch/J2EEFRMW01_5-20002637.SCA version_rule=all
- Once it is done , then trigger the data to the SLD
- Checked the software component in SLD
- Resync the LMDB with SLD
- Then performed the activity of manage system Configuration.
With Regards
Ashutosh Chaturvedi

BIOS - System Information, Model: Can it be Changed?

1. On an EliteBook 8470p (BIOS 68ICF), can BIOS 68ICE be written to it instead?
2. If so, will that change the Model Name as seen in BIOS System Information to read "ProBook 6470b" or will it still show up as an "EliteBook 8470p"
Follow-up question: can a ProBook 6470b Motherboard be installed in an EliteBook 8470p chassis?

Hello e-lumino,
Welcome to the HP Forums!
I understand you would like assistance with your notebook. However, this is a commercial notebook, so you should post your issue on the notebook board of the HP Enterprise Forums for a better answer.
Thank you and have a great day!
Mario
I worked on behalf of HP.

Satellite M45 with disk read error

My Satellite M45 has hung with a "disk read error" on reboot. I have tried cntrl-alt-delete but to no avail. I am loathed to use the recovery disk since it will reformat and I have a feeling my hard disk might be fried anyway.
Has anyone any knowledge on how I can restore this disk inexpensively?
Thanks
G

If you can't boot normally, hit the F8 key during boot up and see if you can get into Safe Mode. If not, running the Recovery CDs maybe the only option.
I would try to run the Recovery CDs even if I thought that the drive might be fried. What is the down side? If it works, you have a working computer. If it doesn't, you know that you were right and the hard drive needs to be replaced.

Satellite C855D-135 - Corrupt BIOS, black screen, keyboard is not working

Hello everybody.
I have been having some issues with my Toshiba Satellite C855D-135 laptop. I had to change my internal hard drive, so I decided to install windows 7 on it (I used to have windows 8 but don't have the CD and I couldn't find the licence key sticker.),
So I went into the BIOS to switch it from UEFI to CSM, but something went wrong at that point and it seems to have corrupted the bios.
I think I have bricked it, but some things still work.
When I turn it on:
- the screen stays black (Yes, I have tried it on a different screen)
- the keyboard doesn't seem to be working (the leds don't turn on when I press caps lock)
- the fan works fine
- cd reader works fine
- When I plug in a USB stick, it flashes quickly once, so that seems to be working
- When I removed the memory bar, the computer did it's series of beeps
- I tried removing the battery, unplugging it and pressing on the power button for ages. (no luck)
- I have tried removing the CMOS battery to revert the bios to default. (no luck)
- I tried flashing the bios on a USB stick, until I realised the keyboard wasn't working and that it was all in vain.
- I tried putting the bios update on a CD, and it spun for a while, but nothing happened in the end. I tried putting these files on the CD:
- IBIOS.BAT
- C8610.FD (in the Win8 folder)
- C610.FD (in the WIN7 folder)
- I tried renaming C8610.FD to BIOS.FD
I have run out of ideas now.
Could anybody help me? Pretty please?
I hope it's not the motherboard that's broken, coz I really don't have enough money to send it off to be repaired.

The whole story sounds very strange to me I never heard about that fact that changing the boot mode from UEFI to CSM would affect the BIOS.
In my opinion there is some serious hardware problem. As you already assumed, it could be probably a motherboard fault.
I would recommend you to ask some technicians for some hardware diagnostic tests to perform an motherboard check in order to be 100% sure about the fault.
If you dont have enough money and the motherboard is really affected you could try to get some 2nd hand part

PI 7.3 - AEX "unable to read configuration data" and login problems

Hello Friends,
after installation of AEX, i'm facing some problems.
1.I'm not able to login with any user, i created during installation wizard. So i cannot check any user in NWA -> User Administration.
2.Once more, while opening http://<host>:<port>/rep or http://<host>:<port>/dir, i get the following error message.
Can somebody help me?
I think, there is a problem with the users, which have been created during installation. How can i check this? Is there any chance?
Second, if i'm able to login, i have to import the exchange profile again. This should solve the problem. Or is this wrong?
PI (http://<host>:<port>/dir/start/index.jsp). Below is the part of the error message that is showing up. Appreciate your suggestions:
Exception class: com.sap.aii.utilxi.prop.api.PropertiesException$InitFailed
Message
Unable to read configuration data (ExchangeProfile/aii.properties)
Stacktrace
Thrown:
com.sap.aii.utilxi.prop.api.PropertiesException$InitFailed: Unable to read configuration data (ExchangeProfile/aii.properties)
at com.sap.aii.utilxi.prop.api.PropertySourceFactory.initServerMode(PropertySourceFactory.java:220)
at com.sap.aii.utilxi.prop.api.AIIProperties.initServerMode(AIIProperties.java:518)
at com.sap.aii.ib.server.applcomp.StartupServerProperties.initPropertiesForServer(StartupServerProperties.java:97)
at com.sap.aii.ibdir.server.applcomp.StartupCodeEntry.startup(StartupCodeEntry.java:151)
at com.sap.aii.ib.core.applcomp.IStartupCodeEntry.startupIfNotAlreadyDone(IStartupCodeEntry.java:43)
at com.sap.aii.ib.core.applcomp.ExplicitApplicationComponentImpl.startup(ExplicitApplicationComponentImpl.java:116)
at com.sap.aii.ib.core.applcomp.ExplicitApplicationComponents.startup(ExplicitApplicationComponents.java:438)
at com.sap.aii.ib.core.applcomp.ApplicationComponent.startup(ApplicationComponent.java:203)
Please let me know if I am not clear.
Edited by: Clarence on Feb 6, 2012 3:28 PM
Edited by: Clarence on Feb 6, 2012 3:28 PM

hi,
>>>>Second, if i'm able to login, i have to import the exchange profile again. This should solve the problem. Or is this wrong?
if you have java stack only there is no exchange profile anymore...
https://weblogs.sdn.sap.com/pub/wlg/28334
Regards,
Michal Krawczyk

Issue with latest Adobe Reader 11.0.10 - Adobe Reader cannot open in Protected Mode due to incompatibility with your system configuration.

Since updating to the most recent Adobe Reader v11.0.10, getting an Adobe Reader Protected Mode: Adobe Reader cannot open in Protected Mode due do an incompatibility with your system configuration. Would you like to open Adobe Reader with Protected Mode disabled?

The solution I was looking for was to launch Adobe Reader in Protected Mode.
I could not identify issues preventing Protected Mode from starting. What ended up working, was to do a complete uninstall, followed by a reinstall. Now we can load Reader in Protected Mode.

Adobe Reader cannot open in Protected Mode due to a problem with your system configuration.

From Adobe website: "Note that this list is not regularly maintained as Protected Mode now runs transparently in the background and it is unlikely that users will experience issues."
This explanation on the Adobe website does not explain what the problem is with the "system configuration". What is the system configuration problem?

Hi Steve,
As mentioned on the troubleshooting page as well normally application like antiviruses, encryption and system maintenance tools causes this kind of problem. These software software intercepts some system calls for the Reader sandbox. Could you please check if you have any of these kind of software installed? Could you please answer following question then I would be in better position to help you?
1. Version of Reader being used
2. OS
3. What happens if you choose launch unprotected? Do you see a failure or Reader launches?
Thanks

[Integration Engine Configuration Data] Error: No access to system landscap

Hi all,
When configuring Integration Engine Data (To go to 'Integration Engine Configuration Data' screen: Tcode: SXMB_ADM -> Choose: Integration Engine Configuration -> F8), we want to load Configuration from System Lanscape by choose F6, an error occur with message as below:
No access to system landscap
So that we can't load configuration from our System Landscape.
We have correctly configured other below:
     - We use http port for corresponding Integration Server.
     - Business System with role 'Integration Server' created correctly in SLD.
     - T-code SLDCHECK is all OK.
     - T-code SXI_CACHE is all OK.
Anyone can please help me correct this error ?
Point will be reward for any valuable answer,
Thanks a lot,
Vinh Vo

Please can you check if your RFC destination SAPSLDAPI and LCRSAPRFC are working both ABAP and Java stack.
just check the reply from Udo and jai's reply
R3 Connecte XI 3.0 Problem
also check page no 18
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/bd5950ff-0701-0010-a5bc-86d45fd52283

Satellite A300D-135 - BIOS - System Configuration Data Read Error

Similar Messages

Maybe you are looking for