Services with different IP address subnets over CSS 11500 series

Hi all folks!
I have two CSS 11500 series...
In just a few months i will have ready a DRS (Disaster Recovery Site), where i will have 2 more servers to add to the environment.
But this servers will be in a different subnet from that today i have for the servers who are configured in the current services of my CSS.
So then the doubt i arises is:
Is correct to add two new services with these servers, but using the IP addressing of the DRS site???, and including on the CSS a static route to this network, (of the DRS) in order to reach them?? is it correct, it will work well?
This would be so....
             ________________LAN to LAN_____________________
             |                                                                                |
             |                                                                                |
|------SITE A------|                                                        |------SITE B------|  
     [Firewall] ===============IPSEC============= [Firewall]               
           |                                                                                |
           |                                                                                |
[CSS-A]-[CSS-B]                                                            [SWITCH]
       |          |                                                                     |         |         
     [SWITCH]                                                                    |         |                                                                 
[srvA] [srvB] [srvC]                                                          [srvD] [srvE]
So, at [CSS-A] & B, i will put a static route to firewall that know the subnet of site B through the IPSEC tunnel.
So In the CSSs, i will add the new services for the Servers "D" & "E" with the IP address of Site B.
This should be seen as well:
!*************************** GLOBAL ***************************
ip route 0.0.0.0 0.0.0.0 [IP FIREWALL]
ip route SITE B [IP FIREWALL]
!************************** SERVICE **************************
service srvA
  ip address A.A.A.x
  port 8080
service srvB
  ip address A.A.A.x+1
  port 8080
service srvC
  ip address A.A.A.x+2
port 8080
service srvD
  ip address B.B.B.y
port 8080
service srvE
  ip address B.B.B.y+1
port 8080
I know that this practice is not the most desirable, in fact should use"Basic Global Server Load Balancing Site Redundancy Using the CSS with DNS", but I don't have much time to change the entire environment today, and in this first stage i have to begin with this poor but quick solution that i thought and i wanted to be validated if there is posibliidades this to work
Within their experiences that they say? Will operate?
Thanks in advance!
Regards!
Esteban =)

Daniel!
Sorry by delay!
Thank you so much for you time for reply.
You have given me a great help to this doubt!
But..using "source group" let me know..
I can´t undertand the really difference between NAT with ACls as you can see at this link: (http://www.cisco.com/en/US/products/hw/contnetw/ps789/products_tech_note09186a0080093dfc.shtml)
and
this other link, using NAT (from the piont 5), (http://www.cisco.com/en/US/products/hw/contnetw/ps789/products_configuration_example09186a0080093dff.shtml)
where the NAT is configured under a method different from the previous one..
So.. for this scenario described above, which would you recommend using? I would think that the second is the most indicated truth? What do you think?
Thanks in advance again!!!
Have nice day!
Regards.
Esteban.

Similar Messages

  • Can't send email using different IP address subnet

    Hi, in our office using different IP address subnet, like this : 
    10.254.1.xxx and 10.254.3.xxx
    And Our Server Exchange version is 2007, using IP address 10.254.1.xxx, but when from another IP like 10.254.3.xxx can't send or receive email, and get error (on some pc that using SeaMonkey) :
    An error occured sending mail : The mail server sent an incorrect greeting: 4.3.2 Service not available, closing transmission channel.
    Someonce can help me, please..
    Thanks before.

    Hi Jim, 
    We have check the following path on our Exchange Server :
    C:\Program
    Files\Microsoft\Exchange Server\Logging\TraceLogs 
    And
    we not found any log files here.
    Thanks.
    Best Regards,
    Antoni

  • How can I transfer contacts from one iPad to a new iPad with different iCloud addresses?

    how can I transfer contacts from one iPad to a new iPad with different iCloud addresses?

    One way would be to e-mail them from yourself to yourself. That would totally avoid the different ID issue.

  • I have two Iphones with different email addresses sharing one Apple ID. Will that cause problems with using messaging and FaceTime?

    I have two Iphones 5 with different email addresses sharing one Apple ID account.Both are using IOS 8.
    I would like to set up a new Apple Id for one of the phones and remove it from the old account.
    If I do that, can I move all of the purchased apps and songs to the new Apple account?
    Also, will sharing one Apple ID account with two devices cause problems with using messaging and FaceTime?

    Sharing an iCloud account between two devices can be done without causing issues with iMessage and FaceTime, just go into Settings for each of these functions and designate separate points of contact (i.e. phone number only, or phone number and unique email address).  While that works, you'll then face the problem where a phone call to one iPhone will ring both if on the same Wi-Fi network -- but again, that can be avoided by changing each phone's settings.
    Rather than do all that, don't fight it -- use separate IDs for iCloud.  You can still use a common ID for iTunes purchases (the ID for purchases and iCloud do not have to be the same) or you can use Family Sharing to share purchases from a primary Apple account.

  • CW2000 ANI Server is finding same devices with different IP addresses

    The ANI Sever is finding devices by multiple ip addresses. One devices is showing up as two devices with different ip addresses. It will show up with the loopback under its hostname and also find it by a serial ip address.

    http://www.cisco.com/warp/public/cc/pd/wr2k/cpmn/prodlit/wk2ke_wp.htm should clear up how ANI works in this case.

  • I inadvertently created 2 accounts with different email addresses - can I merge them?

    I inadvertently created 2 accounts with different email addresses - can I merge them?

    Hi have 2 accounts-accident,
    Please contact Customer Care to have an agent assist you with this. You'll find the contact information here: Contact Customer Care
    Best,
    Sara

  • How do I send docs to multiple signators with different email addresses on Echo sign ?

    How do I send docs to multiple signators with different email addresses on Echo sign ?

    Thanks man...the problem could be on the signators side.
    Rick Schell...Realtor, ABR
    www.rick-the-realtor.com
    Cell 615-804-3085
    Crye-Leike Realtors
    Office 615-373-3513
    Fax 615-373-5228
    Quoting Echosign-Rob <[email protected]>:
    Echosign-Rob  created 
    the discussion
    "How do I send docs to multiple signators with different email 
    addresses on Echo sign ?"
    To view the discussion, visit: 
    https://forums.adobe.com/message/6395941#6395941
    >

  • Do CSS 11500 series allow remote SPAN?

    Hi,
    I found SPAN (Switch port analyzer) is available on CSS 11500 series, but could only found destination must be local. Is it possible to do remote SPAN and make the destination be in another remote switch?
    And how many local span sessions are allowed?
    Thanks,
    Rgds
    Jorge

    Cisco WebNS Software Version 7.20 delivers support for a new Cisco CSS 11501 model and Cisco WebNS Software 7.20 supports SPAN the features.
    Switched Port Analyzer (SPAN) or port mirroring is useful for network analysis?a copy of the packets received or transmitted by a source port is sent to a designated destination port.
    Kindly go through these links to get detailed information:
    http://www.provantage.com/cisco-systems-css11503-ac~7CSCO288.htm
    http://www.cisco.com/en/US/products/hw/contnetw/ps792/prod_release_note09186a008077c440

  • CSS 11500 Series Query

    Hi
    I have 2 CSS 11500 series units working in a master / slave configuration.
    Both units are identical in regards to hardware, IOS, etc.
    1 unit allows the running config to be saved by the ' copy run start' command where the other goes through the motions of saving, but a 'show startup-config' shows nothing.
    This unit seems to be operational in every other regard. Is this a hardware fault or am I missing a software command somewhere along the way ?
    Thanks
    Ian

    You get such problems when the device is running short of memory. Try increasing the DRAM because what is happening is that the device saves the config in the NVRAM but it does not have enough DRAM to display the configuration when the "sh startup-config" command is executed. A temporary solution is to restart the device, if the problem persists then you have to upgrade the memory.

  • Why connect two dhcp servers with different IP addresses?

    
    so for an assignment at college we had to configure a router connected to two switches which both had a server connected to them.
    the computers were connected via dhcp to either server however each side had a different IP. we have now been asked to justify as to why two servers were used with different IP which I cannot quite produce a business orientated answer.
    I can understand connecting two dchp servers on same IP to increase fault tolerance but I do not understand using two separate IP addresses.

    Hi,
    Does “using two separate IP addresses“ mean 2 subnets which are connected by router？
    If you have separately configured 2 DHCP servers on the 2 subnets, and want 1 of the 2 DHCP servers to provide fault tolerance for the other. You need to use an RFC 1542–compliant router, or DHCP relay agent, in order to forward DHCP broadcast traffic.
    If there is any misunderstanding about your question, please correct. 
    Best Regards,           
    Eve Wang                                                                             
    Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

  • IDoc ORDERS01 with different shipping addresses

    Hi,
    we are using IDOC ORDERS01 to create customer orders in the ERP. Which is working fine as long as we are using just a partner number as ship-to-partner in the IDoc. Now it should be possible to also use different ship-to-partner addresses. So the idea was to use the same partner number for the ship-to-partner as before but add the different ship-to-partner address in the corresponding IDoc fields (IDoc segment E1EDKA1 for PARVW = WE). Which is also working fine except for the house number. Street name and house number are put together in IDoc field E1EDKA1-STRAS. And they also stay together in the street field of the resulting ERP sales order. But the address structure (for example in the partner deatails of the sales order) uses an own field for the house number. This field is not set with the house number from the street field in the ORDERS01 IDoc but with the house number of the default address of the used ship-to-partner number. Which means that the street line for the ship-to-partner has a street name and two house numbers which is of course not what we want to be displayed in sales orders. So how can we make the right house number from the ORDERS01 IDoc the one and only house number in the sales order? How can we overwrite the default house number of the default ship-to-partner address with the house number of the different shipping address from the ORDERS01 IDoc?
    Regards,
    Robert

    Hello Robert
    Check out the following OSS notes:
    1457805 - Fields not populating on inbound order through idocs.
    618476 - EDI: Field HAUSN is not filled- This is for older release and for INVOIC01, but may be you can borrow and develop the concept for   ORDERS01.
    Also did you consider leaving House Number blank in the customer master, i.e.
    in the street/house Number Filed, maintain like this:
    6201 W IMPERIAL HWY/ blank
    but not as
    W IMPERIAL HWY/6201
    That's how these fields are populated in my system.
    Hope this helps. Let me know.

  • Accept iCal invites with different email addresses?

    Hi there
    I receive calendar invites through a variety of different email addresses. I can only accept/save the invite to iCal (not a Google calendar for instance). Invites won't save to a stipulated calendar, only the default one.
    I cannot notify acceptance of an invite unless it has come to an Apple email address, so work and personal email addresses show that I have been invited but the caledar does not recognize alternative addreses and as a result I cannot confirm acceptance.
    Is there anyway to configure iCal to recognize multiple adresses or is there another application that you can suggest that works with multiple addresses?
    Many thanks for looking.

    At what stage does it change? What happens if you start the email with a capital? What happens if you select the address from the pop-up? What happens if you drag the address across from Address Book?
    AK

  • Same Vendor with different delievery address - subcontract challan plz help

    Dear Experts,
    I am sending the same material to the vendor, and making the subcontracting challan against that. now my problem is that the vendor is having two different delivery location. so i have to transfer the material to two different location with two different subcontracting callan.
    so what should i do? how can i do 541 for two different delivery address but the same vendor code.
    please guide on priority.
    any answer which will help me achieve the solution will be rewarded

    Alternative:
    Your Requirement is for printing the delivery address as per the delivery address given by vendor. This u can do by maintaining an additional partner function. Add this partner function to the purchase order. In the print the address is picked from the master data of this additional partner.
    If u want tracking at the level of your stock at which vendor site, then u need to maintain two vendors.

  • How can I pin multiple instances of Firefox to the taskbar in Windows 7 with different web addresses

    I pinned Yahoo Mail to my taskbar by dragging it down from the desktop. When I try to do that with a second address, it doesn't pin the second address, only a second copy of Yahoo mail.

    I just set Safari's option to None. That is I right clicked on the dock, selected options, and chose none. Also, in Mission Control's tab of System Preferences I clicked Off When switching to an application, switch to a space with open windows for that application. That let me open a new Safari window no matter what desktop I was in. But I had to do both. Just setting the desktop option to none didn't seem to do it. Finder seems to work okay with just the none option set.

  • Issue services with different Internal Orders within a Plant from one PO?

    Hiii... Please advice me of issuing services through one purchase order (one vendor comes and do the service to different machines of different internal orders in a plant) to different  internal orders within a plant.
    Thanks
    Manoj

    what is the problem?  you can have Multiple Line Items in a PO  (one for each internal Order).
    And within one Line item you can add multiple service lines.

Maybe you are looking for