Sessions get disconnected with a STATUS 26

I'm running Solaris 10 x86 update 5 will all patches that smpatch said were available and Sunray Software 4.0 with patch 127554.-03. All this is running on an X4150 within ESX 3.5. The DTUs seem to run fine after anywhere between 4 hours to 3 days and then they goto a STATUS 26. I utswitch'd over to this new sunray server so power cycling my DTU only brings me back to my original sunray server that runs fine (solaris 10 x86 update 2, sunray software 4.0 no patches). When i attempt to utswitch back to the new sunray server, i get stuck with the status 26 again. The only way i can log back into the new sunray server is to do a utrestart -c on the new sunray server. Something to note is I only have 2 sunray2 FS DTUs connecting to this new sunray server and they both DON'T get status 26s at the same time.

We have a set of 7 servers (heterogeneous hardware) all running Solaris 10 on a patch level not older than three month.
Three of them seem to cause no problems at all (classic UltraSPARC platforms).
Another also seems not involved though it's differetn hardware (SunFire X4100, AMD Opteron)
Two occasionally cause this 26D problem (T1 processors)
And the last one immediately and always "hijacks" all DTUs and then lets them starve. (T6320 blade module, T2 processor)
Even after putting raysrv7 to offline and stopping the ray services there are still a couple of Xnewt processes occupying DTUs.
When I do a pstack to one of them it does not look sound with respect to the arguments of pollsys or WaitForSomething.
We did not yet apply patch 127554-05, but as far as what I'm reading here it does not really sound promising to do so.
root@raysrv7 1# ps -ef|grep Xnew
root 13448 13371 0 15:23:06 ? 0:01 /opt/SUNWut/lib/Xnewt :34 -nobanner -auth /var/dt/A:34-gJayhA +bs
root 22379 22359 0 15:42:48 pts/3 0:00 grep Xnew
root 13824 13371 0 15:23:07 ? 0:01 /opt/SUNWut/lib/Xnewt :25 -nobanner -auth /var/dt/A:25-pJayhA +bs
root 13638 13371 0 15:23:07 ? 0:01 /opt/SUNWut/lib/Xnewt :28 -nobanner -auth /var/dt/A:28-mJayhA +bs
root 14116 13371 0 15:23:08 ? 0:01 /opt/SUNWut/lib/Xnewt :22 -nobanner -auth /var/dt/A:22-sJayhA +bs
root 13549 13371 0 15:23:07 ? 0:01 /opt/SUNWut/lib/Xnewt :30 -nobanner -auth /var/dt/A:30-kJayhA +bs
root 15244 13371 0 15:23:10 ? 0:01 /opt/SUNWut/lib/Xnewt :7 -nobanner -auth /var/dt/A:7-BJayhA +bs
root 13381 13371 0 15:23:06 ? 0:02 /opt/SUNWut/lib/Xnewt :39 -nobanner -auth /var/dt/A:39-bJayhA +bs
root 14833 13371 0 15:23:09 ? 0:01 /opt/SUNWut/lib/Xnewt :16 -nobanner -auth /var/dt/A:16-yJayhA +bs
root@raysrv7 2# pstack 13448
13448: /opt/SUNWut/lib/Xnewt :34 -nobanner -auth /var/dt/A:34-gJayhA +bs
ffffffff7e2d9c2c pollsys (ffffffff7fff69c0, a, ffffffff7fff7280, 0)
ffffffff7e273bf0 pselect (a, ffffffff7fff69c0, ffffffff7e444710, ffffffff7e444710, ffffffff7fff7280, 0) + 1f0
ffffffff7e273f94 select (ff, 10043df08, 0, 0, ffffffff7fffd390, 1005f4d58) + a0
000000010009e308 WaitForSomething (ffffffff7ffff450, 1, 1005df480, 1003baa00, 1003b1600, 1003baa00) + 5d0
00000001000d9d0c Dispatch (4800, 1, 1004d6978, 0, 10043ffa8, 4800) + 33c
00000001001055b8 main (5308, 1003bb874, 1004d6630, 1003b1600, 1005f3cb8, 1005f3cb0) + 930
000000010003c2bc _start (0, 0, 0, 0, 0, 0) + 17c
Any suggestions? Any help? Or is this a dead thread?
Regards
Karl

Similar Messages

  • IDOC is Getting Fail with - 56 Status EDI Partner profile not available

    Hi,
    I am trying to Post invoice Data into IDOC on ECC Side.
    My Scenario is File u2013 XI u2013 ECC(IDOC).
    But It is Getting Fail with 56 Status u201C EDI: Partner profile not available u201C
    On Control record I am getting this
    Port                       BLANKKKKKKKKKK
    Partner Number              CLNTDEC110      Logical system for Client
    Partn.Type       LS                    Logical system
    Function                                  BLANKKKKKKKKKK
    Port                            SAPDPI
    Partner number             CLNTSAMPLE
    Partn.Type                      LS         Logical system
    Partner Role                   BLANKKKKKKKKKK
    My configurations are Like this :----
    On ECC  Side  MY SID is DEC
    On ECC side I have two logical system in CLNTDPI100 for PI
                             CLNTDEC110 for ECC.
    I have Partner profile on ECC system on CLNTDPI100 logical system    - we20
    Added message type in inbound side of partner Profile (INVOIC-INVOIC02)
    ON SAP PI/ XI System  MY SID is DPI
    IDX 1 has Port name SAPDEC
    On Message mapping EDI_DC40 is mapping with constants with below given value
    <INVOIC02>
       <IDOC BEGIN="">
          <EDI_DC40 SEGMENT="">
             <TABNAM> </TABNAM>
             <DIRECT>2</DIRECT>
             <IDOCTYP> </IDOCTYP>
             <MESTYP>INVOIC</MESTYP>
             <SNDPOR>SAPDPI</SNDPOR>
             <SNDPRT>LS</SNDPRT>
             <SNDPRN>CLNTDPI100</SNDPRN>
             <RCVPOR>SAPDEC</RCVPOR>
             <RCVPRT>LS</RCVPRT>
             <RCVPRN>CLNTDEC110</RCVPRN>
          </EDI_DC40>
    Regards
    PS

    Check the following :
    in We 02 which  partner number is displayed just in the posted IDOC -> 2nd coloum in the IDOC list .and verify if the
    same you have in Partner profile. Actually this details comes from  ECC business system's logical system name which you give in SLD.
    in we 19  - take the error iDOC numner and  open the IDOC ->click on the first line -> check entries as you mentioned
    above  sender port should be PI port not empty.you need to check the partner profiles properly
    follow these steps
    1. create a RFC destination of tyoe H for Pi system- 2. create a Port  and assigen the RFC destination to it
    3 create logical system for PI BD54 PICLNT001 say , 4 with the same name create a partner profile in We20
        in parter profile  maintain the  inbbound message parameters  and add the PI port as receiver port in it .Give the basic type also .
    now
    for sender details  in ur case PI : u have  port (defined in PI IDX1),patner number (LS defined in ECC PICLNT001), parter type LS.
    for  receiver  you have port defined (as above), partner number the logical system for ECC system.
    in we 19 ,, edit the control record as above and  go to the tab inbound processing and test the internal posting
    it should work fine. in the adapte specific attribuet for receiver ECC system , maitain the same LS name , if any wrong entry is
    there then change the LS in sld to poing to correct LS/
    refer this
    http://www.riyaz.net/blog/xipi-settings-in-r3-partner-system-to-receive-idocs/technology/sap/26/
    Regards,
    Srinivas

  • Calls Getting disconnected with reason code 26

    Hi,
    Few of my calls are getting disconnected with reason code 26. on agent screen it just flash and disconnect.as per RCD its showing Error code 0( fine) and finally its ending at Skill Group Node. talk time is 1 or 2 seconds. agents having auto answer setting as well as IP Phone set auto ans with headset.
    my setup is IPIVR based UCCE setup.
    Please help
    Regards-
    PK

    Hi PK,
    CD 26 normally indicates Resource Not available in CUCM side. please check the Jtapi gateway process logs for the failed calls. you should be able to see something similar to below
    19:08:37:896 PG1A-jgw1 Trace: ConnFailedEv CID: 27224748 Addr: 80002985 CiscoCause: CAUSE_RESOURCESNAVAIL Cause: CAUSE_RESOURCES_NOT_AVAILABLE.
    if that is the case , please check from CUCM perspective as well.
    Regards,
    Sasikumar.

  • Client getting disconnected with CTISVR

    Hello Everyone,
    I am using ICM 8.5(2).Recording servers which are communicating with ctisvr are getting disconnected continuously.
    While observing the logs ,found the below mentioned termination reason.
    14:19:16:421 cg1B-ctisvr Transmit queue limit of 15000 messages exceeded by client PGUser (session 223).
    14:19:18:499 cg1B-ctisvr SESSION 223: Terminating client PGUser at (172.19.241.16:3440), E_CTI_UNSPECIFIED_FAILURE
    14:19:18:499 cg1B-ctisvr Trace: CTILockObject::Unlock - WARNING: - Long Lock Warning on Global\Session Lock, Thread 4500 held lock for 2078 ms, exceeded threshold 500 ms
    14:19:18:499 cg1B-ctisvr Trace: TransportProtocol::QueueMSG - PGUser (SessionID 224) , Message queued:  (11517 msgs in the queue, max:15000)
    14:19:18:499 cg1B-ctisvr Trace: TransportProtocol::QueueMSG - Verint (SessionID 226) , Message queued:  (13639 msgs in the queue, max:15000)
    14:19:18:499 cg1B-ctisvr Trace: CTILockObject::Unlock - WARNING: - Long Lock Warning on Global\Master Session Lock, Thread 4500 held lock for 2078 ms, exceeded threshold 500 ms
    14:19:18:499 cg1B-ctisvr Trace: TransportProtocol::UnQueueMSG - PGUser (SessionID 224) , Message unqueued:  (11516 msgs in the queue, max:15000)
    14:19:16:421 cg1B-ctisvr Transmit queue limit of 15000 messages exceeded by client PGUser (session 223).
    14:19:18:499 cg1B-ctisvr SESSION 223: Terminating client PGUser at (172.19.241.16:3440), E_CTI_UNSPECIFIED_FAILURE
    14:19:18:499 cg1B-ctisvr Trace: CTILockObject::Unlock - WARNING: - Long Lock Warning on Global\Session Lock, Thread 4500 held lock for 2078 ms, exceeded threshold 500 ms
    14:19:18:499 cg1B-ctisvr Trace: TransportProtocol::QueueMSG - PGUser (SessionID 224) , Message queued:  (11517 msgs in the queue, max:15000)
    14:19:18:499 cg1B-ctisvr Trace: TransportProtocol::QueueMSG - Verint (SessionID 226) , Message queued:  (13639 msgs in the queue, max:15000)
    14:19:18:499 cg1B-ctisvr Trace: CTILockObject::Unlock - WARNING: - Long Lock Warning on Global\Master Session Lock, Thread 4500 held lock for 2078 ms, exceeded threshold 500 ms
    14:19:18:499 cg1B-ctisvr Trace: TransportProtocol::UnQueueMSG - PGUser (SessionID 224) , Message unqueued:  (11516 msgs in the queue, max:15000)
    Is the termination reason is due to exceeding transmit queue limit of 15000 messages or not???
    If yes kindly suggest the resolution of the same.
    It would be a great help to me.
    Thanks in Advance.
    Regards,
    Arpit Arora

    hi,
    what about the manual?
    http://download.oracle.com/docs/cd/E11882_01/network.112/e10746/toc.htm
    Also some startup information can be found in docid 76629.1 Overview and Configuration of ASO Encryption
    Also if they are interested in encrypting data with TDE I found the following on OTN:
    TDE column encryption Implementation Guide and Script for PeopleSoft :
    http://www.oracle.com/technetwork/database/security/tde-comp-tool-160389.zip
    greetings,
    Harm

  • Async call gets stuck with pending status

    Hi,
    I am working on Tasklayer where need to invoke Async. call, the .bpel file has Invoke activity and below that it has pick activity with branches one for OnMessage and another is also OnMessage but, this is for fault. Now, when it invokes the Async. what i see in the instance is that the OnMessage activity gets stuck in Pending status, it doesn't proceed further. Kindly let me know if any one has faced similar issue.
    Thanks & Regards,
    Sanjay

    Hi Sanjay,
    you are saying that u r calling an asyc process.
    So as an async process do not send the response back to parent through same port, you have to send the fault back to parent by invoking it(parent).
    Here you can send the fault by using existing callback port otherwise you can define separate port for fault can send through that(you have to do it in WSDL).
    So here for the first case no need to have the pick as u r getting both success and fault through same port. If you are going for separate one you have to have pick(one for success and other for faulted one)
    So as Steven said you have to have a catch and invoke to send the fault back to parent.
    Regards
    PavanKumar.M

  • Outlook 2010 gets disconnected with Exchange 2010

    Hi
    We are facing a strange issue that some Outlook users are getting disconnected and it reconnects after 1 or 2 hours or after changing the IP of the system. During the Outlook disconnection period we can't even telnet on port 433 to the CAS BLB name or IP
    (same time we can able to ping CAS name). The security and network team is checking the same, is there any thing to be checked with Exchange servers regarding this issue?
    Thanks in Advance
    LMS

    Also I found a similar article "http://social.technet.microsoft.com/Forums/exchange/en-US/06f4d721-a778-4437-b43a-9ad6ca70344b/outlook-clients-randomly-disconnected-from-cas-array?forum=exchange2010"
    which almost explains the same issue - users are getting disconnected and even unable to telnet teh cluster IP and getting connected after a few minutes.
    So we will go ahead and re configure the NLB. We plan to keep the existing NLB on one server and remove and add second node and do the same for the other. What do you think?
    LMS

  • HT204406 How can i get tracks with "waiting" status to upload to itunes match.

    I have completely cleared my library and started again. i have 24000 tracks in library but only 15000 + are uploading. leaving a further 6000 or so with a "waiting" status. i have tried the update itunes match option which runs through the full process and on completion is still leaving the tracks with "waiting" status.
    any ideas??

    I have the same issue, although I only have about 2500 tracks and half of them are in waiting. I read a few other peoples issues with this problem and checked and found that all the songs (or whatever it is) are not in the folder they were in, in fact they are not on my computer anymore! They are still in the cloud i guess, well the information is, but the songs arent.  So now I have to go back and re-import all the CD's that are missing.  I did reinstall itunes before this happened which probably had something to do with it, but whenever I tried to update itunes match it would freeze my computer and give me an error.  So I reinstalled and now it works but half my music is gone! and alot of it was not on CD, I had gotten online, but when I go to check purchases/downloads available, it says everything that can be has been.  It ***** because it takes so long and I know I have lost some of the songs since I got them online and dont have a hard copy.  But basically you need to check to make sure the files are in the folder that itunes is looking in, and that they are ON your computer or server.  Then re-import if you have to, and update itunes match (if your using) then icloud should recognize.  Ill let you know if this works for me since I am in the process of doing just that.  

  • QuickVPN successful session gets disconnected

    Hello,
    I have been installing RV042 routers in my clients homes for automation systems.  We set up VPN to use the Quick VPN utility and I am having an issue.  I am using Windows 7 64bit on the client end and can successfully connect.  After a period of time, usually an hour or so the remote network becomes unavailable and an error message pops up on the client that reads; "Remote is not responding. Do you want to wait?".  Clicking "yes" delays the popup for approx 30 seconds.  A "no" response disconnects the session.  Attempting to reconnect results in sucessfull connection but failed verification with "Failed to ping remote VPN Router."  and then a disconnect.  Both routers, client side and the remote, are RV042 models and both systems are with Comcast service. (Also happens to other service provider systems that other clients have.) On the QuickVPN client side I do have port 443 and 500 forwarded to my PC with windows firewall off.   Any ideas??
    Jon

    I am the only user at this time.
    I tried the connection this morning and I still cannot connect.  Previously, I haven't had the time to investigate the disconnect so I'd just leave the thing alone and eventually I'd need to connect and it would work.
    I am pretty sure a reboot of the remote router has not happened before successful reconnection.
    What should I look at?

  • Everyday around 3 to 4 PM all RDP sessions (around 50) getting disconnected

    Hi,
    We have a Windows 2008 R2 Terminal Server (workgroup) with SQL Server and C# application installed on the same terminal server.
    Around 50 users access this terminal server. Since 15 days, everyday between 3PM to 4 PM, all the 50 user sessions gets dicsonnected at the same time and without anything done on the server, users can RDP again and work without any problems.
    Verified event logs, terminal server logs, network, firewall, router etc. everything is working fine.
    Only thing observed is, when RDP sessions gets disconnected, we see PING time out.
    Any help to address this issue is appreciated.
    Raghuveer.

    Hi this is the error, users are experiencing.
    The session won't go into disconnect status, it stays ACTIVE only in the terminal server.
    User session freezes for 5 to 15 seconds and the same RDP session continues to work without any manual intervention.
    Is this network issue ? We ruled out network cable, routers problems if any in both client and server locations.
    Error: Reconnecting
    The connection has been lost..Attempting to reconnect to your session...
    Connection attempt 1 of 20
    Enabled following :
    Open Group Policy Object Editor:
    (command line: gpedit.msc)
    Navigate to Computer Configuration/Administrative Templates/Windows Components/Terminal Services
    Click on Keep-Alive Connections and select enabled.
    Any other suggestions is beneficial to us to fix this issue.

  • REPORT GETS HUNG WITH THE REPORT QUEUE SHOWING THE STATUS OF OPENING

    I have installed Oracle 9ids on windows 2000 platform. This installation is part of the oracle clinical installation process.
    The installation went on fine except few problems during generating reports. I am able to generate report but as soon as any one of the report fails it stops all the subsequent reports . The failing report has the status of "Opening" in the report queue manager whereas all the subsequent reports get stuck with the status of "Firing before trigger" status in the report queue manager.
    Has anybody encountered the same problem or anything similar... if so, pls hlp...
    Regards,
    Venus

    I tried this Gill, but result is bit different :-
    Seems some little modifications are needed. Report should be displayed like the below one where it says how many times the same Task is associated with the same incident. Eg. Task 'TASK_CIRCUIT_RESOLVER' is associated with the incident 'INC000000001434' 4 times. 'IPCG Diagnostic Template' is associated with  'INC000000000943' 2 times. Similarly for other records.
    But I really thankful to you for giving me the logic proceed further. I tried  '=RunningCount([Task Name]; Row; ([Task Name]; [Incident ID]))'. It gave me desired results. :-
    But the only thing that needs to be done is to bring the single Task associated with the Incident..
    Thanks,
    Neha Pateria

  • Session geting disconnected before IDLE_TIME in profile

    Hi !
    My database is :
    SQL> select * from v$version;
    BANNER
    Oracle9i Enterprise Edition Release 9.2.0.4.0 - Production
    PL/SQL Release 9.2.0.4.0 - Production
    CORE 9.2.0.3.0 Production
    TNS for Linux: Version 9.2.0.4.0 - Production
    NLSRTL Version 9.2.0.4.0 - Production
    on os :
    SQL> !uname -a
    Linux abc-dc 2.4.21-50.ELsmp #1 SMP Tue May 8 17:18:29 EDT 2007 i686 i686 i386 GNU/Linux
    I have created a profile Kill_session and set idle_time as 30 minutes(I think the unit for this value is min).
    and the profile has been given to the a user genweb. Now when I log in with genweb the session getting disconnected very frequently....not even staying 3 min. inactive.
    Its showing :
    ORA-02396: exceeded maximum idle time, please connect again
    But if I assign default profile to the user genweb in which idle_time is unlimited the session is not getting disconnected.
    The ping response is strong. Issue is happening in both the case, if I connect via listener or connect logging in the server.
    Also :
    sho parameter resource
    NAME TYPE VALUE
    enqueue_resources integer 1692
    resource_limit boolean TRUE
    resource_manager_plan string
    SQL> select * from dba_profiles where profile='KILL_SESSION';
    PROFILE RESOURCE_NAME RESOURCE LIMIT
    KILL_SESSION COMPOSITE_LIMIT KERNEL DEFAULT
    KILL_SESSION SESSIONS_PER_USER KERNEL DEFAULT
    KILL_SESSION CPU_PER_SESSION KERNEL DEFAULT
    KILL_SESSION CPU_PER_CALL KERNEL DEFAULT
    KILL_SESSION LOGICAL_READS_PER_SESSION KERNEL DEFAULT
    KILL_SESSION LOGICAL_READS_PER_CALL KERNEL DEFAULT
    KILL_SESSION IDLE_TIME KERNEL 30
    KILL_SESSION CONNECT_TIME KERNEL DEFAULT
    KILL_SESSION PRIVATE_SGA KERNEL DEFAULT
    KILL_SESSION FAILED_LOGIN_ATTEMPTS PASSWORD DEFAULT
    KILL_SESSION PASSWORD_LIFE_TIME PASSWORD DEFAULT
    KILL_SESSION PASSWORD_REUSE_TIME PASSWORD DEFAULT
    KILL_SESSION PASSWORD_REUSE_MAX PASSWORD DEFAULT
    KILL_SESSION PASSWORD_VERIFY_FUNCTION PASSWORD DEFAULT
    KILL_SESSION PASSWORD_LOCK_TIME PASSWORD DEFAULT
    KILL_SESSION PASSWORD_GRACE_TIME PASSWORD DEFAULT
    SQL> select profile from dba_users where username ='GENWEB';
    PROFILE
    KILL_SESSION
    I had to change the profile for the user to default.
    Sorry for posting all this long output. Pls. help me ....
    Am I missing something here?
    Edited by: gc on Jan 21, 2011 2:11 AM

    SQL> create profile KILL_SESSION2 limit idle_time 30;
    Profile created.
    SQL> ALTER USER GENWEB PROFILE KILL_SESSION2;
    User altered.
    But same result.
    Connecting through plsql developer from a client pc. also login to server using putty and then sqlplue in both case sessions are disconnected in seconds.
    sho parameter resource_limit
    NAME TYPE VALUE
    resource_limit boolean TRUE

  • Pc Suite via bluetooth getting disconnected on E61...

    Hi,
    I recently updated to Nokia_PC_Suite_683_rel_14_1_eng_us_web and now I am having troubles when trying to sync.
    I am getting the message [device name] connected via bluetooth and several seconds later it's getting disconnected with the message: [device name] disconnected via bluetooth --> in E61
    In 6230 - it's getting crazy and the phone is being shot down.
    I restarted both phones many times, restarted also the computer.
    Yesterday it worked for a while, I managed to syn my calendar but today it's not working again.
    until now I used an older version PC_Suite_681_rel_13 and it worked properly.
    I tried to go back but it's not working now.
    My Os is winxp- SP2
    PC suite version PC_Suite_683_rel_14_1_eng_us_web
    Bluetooth: Widcomm ver 4.0.1
    Machine - HP notebook.
    I hope someone has an idea.
    Tnx!
    pablo

    10-Jun-200701:50 PM
    pablo_1 wrote:
    Hi,
    I recently updated to Nokia_PC_Suite_683_rel_14_1_eng_us_web and now I am having troubles when trying to sync.
    I am getting the message [device name] connected via bluetooth and several seconds later it's getting disconnected with the message: [device name] disconnected via bluetooth --> in E61
    In 6230 - it's getting crazy and the phone is being shot down.
    Tnx!
    pablo
    I'm having the same problem. Uninstalled old PC suite and installed Nokia_PC_Suite_683_rel_14_1_eng_us_web today.
    With 6230i, phone is seen and a bluetooth connection is made but almost immediately PC suite disconnects. Can't even get a DKU-2 cable connection anymore.
    Useless!
    Help! Any ideas anyone?

  • Spool with 'Eror' status.

    When i print the invoices, it gets printed correctly with spool status as 'Completed' for some of the local output device (LOCL,HOLE) but for the output device(ZPDF( PDF output using Email)), spool is getting created with 'Error' status.
    When i checked the log for error status, its coming as 'Character converter active when first problem occured'.

    Hi Ashish,
    Check with the basis team for the log error ....
    Regards,
    Sravanthi

  • [svn:bz-4.0.0_fixes] 23961: Bug#3200562: New Flex Session Id generated while disconnect with streaming amf channel

    Revision: 23961
    Revision: 23961
    Author:   [email protected]
    Date:     2012-06-15 04:42:44 -0700 (Fri, 15 Jun 2012)
    Log Message:
    Bug#3200562: New Flex Session Id generated while disconnect with streaming amf channel
    While invalidating session, make sure a new one does not get created.
    Modified Paths:
        blazeds/branches/4.0.0_fixes/modules/core/src/flex/messaging/endpoints/BaseStreamingHTTPE ndpoint.java
    Property Changed:
        blazeds/branches/4.0.0_fixes/modules/

    You're trying to do this directly in ActionScript without using Flex, correct?
    The mxmlc compiler for Flex adds some registerClassAlias calls to map types between the client and the server. This will be missing if try to use the messaging code outside of a Flex app.
    Take a look at the mx.utils.RpcClassAliasInitializer class in rpc.swc. This has a static registerClassAliases method that will do the class registration for you. You should just need to call this before running your messaging code.
    -Alex

  • [svn:bz-4.6.x] 23962: Bug#3200562: New Flex Session Id generated while disconnect with streaming amf channel

    Revision: 23962
    Revision: 23962
    Author:   [email protected]
    Date:     2012-06-15 04:57:45 -0700 (Fri, 15 Jun 2012)
    Log Message:
    Bug#3200562: New Flex Session Id generated while disconnect with streaming amf channel
    While invalidating session, make sure a new one does not get created.
    Modified Paths:
        blazeds/branches/4.6.x/modules/core/src/flex/messaging/endpoints/BaseStreamingHTTPEndpoin t.java

    I thought the same that those devices simply are too old. However I would like to know what causes this capabilities change. We want to get rid of the old H/W, but at the moment it looks as if we would need to revert back to the 4402 in order to get those things working again.
    I have not enough information, but those devices are some kind of handhelds. Their MAC OUI belongs to Newport Electronics.
    Regards,
    Patrick

Maybe you are looking for