Set up Calibration Inspection in Inspection Interface

Hello,
I’m currently designing an inspection interface “front panel” for a program that detects faults in caps. I’ve been having a look at some of the features that are offered in the interface and I was wondering if there is a way I can perform an edit calibration in the inspection interface. Thanks for any response.

Actually, the Calibration step in VBAI allows you to dynamically relearn calibrations based on previous points. The simple calibration and point distance calibrations allow you to use previous points to update the calibration. On the second tab of the calibration step, check the relearn option. All calibration types allow you to dynamically adjust the calibration origin/angle based on previous points using the same relearn flag in the calibration step.
If you want to permantely update the calibration, you can check the "Save Image Calibration to File" option on the first tab of the calibration step.
Hope this helps,
Brad

Similar Messages

Any advantages to setting the AP-Manager and Management interface to an untagged vlan?

Any advantages to setting the AP-Manager and Management interface to an untagged vlan? Currently, our controllers have their management and ap-manager interfaces on the same untagged vlan. Would it be wise to change this? Are there any gotchyas I should be aware of?

No really, there won't be a problem. Management an AP-manager can be on different vlans.
The vlan you chose to untag is the vlan you should declare as native on the switch, that's it.
No advantage in having interfaces configured in a way or another.
Some people want the management to be in a "management" subnet and the ap-manager will be in the subnet with all the APs. Some others have several AP subnets so the ap-manager is in the same as management ... no importance whatsoever as long as the config is coherent.
The only thing that is worth considering is the size of AP subnet to me. If you give a /16 for APs and have 1000 APs in a single subnet, ARP and broadcast storms will be hitting the fan. But the vlan tag/untags that you chose are not important
To rate an answer, click on the stars below it. 1 for not so useful and 5 for very useful.
Nicolas
===
Don't forget to rate answers that you find useful.

PowerShell: How do I reliably set the IP address on an interface when the interface is not connected ?

Hello all,
I am in a bit of a bind - no pun intended. I would like to know how to reliable set the persistent IP address of an interface that may be disconnected when the address is set. I can set an address and it will be stored in the ActiveStore but
that does not really help if I need it next time I reboot. I have tried using netsh and WMI but they don't seem to create a persistent address on the disconnected interface. Now if I us ncpa.cpl I can do it all day long so it must be possible.
In fact if I do it that way the registry settings change. So, I figured I would go that route (modifying the registry) but, alas, that does not work either - upon reboot the address shown in the interface properties show a blank IP address, gateway,
and netmask. It is interesting that it is using a static address though.
Thanks for your help
Robert
Robert Thompson

Look in the Gallery for numerous examples of setting a static address on an interface.
http://gallery.technet.microsoft.com/site/search?query=static&f%5B2%5D.Value=static&f%5B2%5D.Type=SearchText&f%5B0%5D.Value=networking&f%5B0%5D.Type=RootCategory&f%5B0%5D.Text=Networking&f%5B1%5D.Value=clientside&f%5B1%5D.Type=SubCategory&f%5B1%5D.Text=Client-Side%20Management&ac=2
¯\_(ツ)_/¯

Inspect and Inspected field in Record Results:Characteristic overview

hi,
Can any one explain me the Inspect and Inspected field in Record Results:Characteristic overview screen. How the sample size is determined in Inspected field during lot creation.
Muthamil

Dear Muthamil
This fully depends on the sampling procedure you choose. for eg if you choose 100% sampling procedure and you have lot quantity of 10 items
Then inspect will be 10 and inspected will be 10.
SAP gives the definition for INSPECT as - Predefined sample size that has to be inspected for an inspection characteristic or a partial sample.
For each inspection plan characteristic you define the amount by which the inspected sample size in the 'Insp.ed' field can deviate from the to-be-inspected sample size in the 'Inspect' field. If a characteristic (partial sample ) is closed the system checks whether the required sample size is adhered to. The characteristic (partial sample) can only be closed if this is the case.
But for Scope not fixed, larger , smaller scope the inspected field chages based on the result recording
SAP gives the definition for INSPECTED as - Number of sample units that have been inspected for a characteristic or a partial sample.
Hope this explains
Regards
Gajesh

QM : First inspection lot - inspection plan, other inspection lot another insp. plan

Hello.
Is it possible with standard SAP when it is create the first inspectio lot for material/vendor ( origin 01) that it takes an inspection plan, and for the next inspection lot that will be created for the same material/vendor ( origin 01) that system takes from another inspection plan ????
Or have i to user a badi/user-exit?? which?
Regards.
Antonio

Dear Antonio,
Try this
1. In material master do not set the auto release indicator for 01 inspection type
2. Make inspection plant for material with group counter 2
3. Now you have two different inspection plans with group counter1 &2
4. Do the GR for same material for two times
5. Two inspection lots will be generated
6. Assign inspection plan manually for first inspection lot with first group counter
7. Assign inspection plan manually for first inspection lot with second group counter
Please let me know is it working or not
Regards,
Jagan

One PI set up for all the outbound interfaces

Hello Friends,
We have set of interfaces from SAP to 3rd party using PI system. We will not do any mapping for any interface in PI
We will receive the IDocs ( Orders , deliveries , shipping and alll ) from SAP and send it to 3rd party.
is there any way to send these IDoc's with only set up in PI ... only one repository and directory for all the messages )
Thanks

Hi
One way could be that on save of each transaction or event, an xml file is created which can be passed to the receiver.
Regards
Monika

Set an attribute inherited by an interface

Hello,
I've got a problem setting an attribute, so i appreciate your help or a link to a solution in advantage.
Situation: I've created an interface hosting some attributes. I've created an business object inheriting the interface. Now i try to set the value of the interface's attributes by invoking an interface's method (handing over the standard container of the business object). Unfortunatly, as result there are created new container elements instead of setting the interface's attributes.
How can i fix this problem?
Thanks, Stephan

I think you have misunderstood a thing or two with respect to enhancing/developing BOR object types. You should definitely implement the attributes. It should always be the attribute implementation code that sets the container value - even if it is technically possible to do it in some other way, this is bad practice and not upwards compatible if SAP enforces a more strict interface check (same problem that applies to undeclared parameters for methods).
Using a method to set attribute values is just stupid. It requires an extra step in the workflow, and it is not necessary since attributes will be automatically populated whenever they are needed. Additionally, if your attributes were only populated after a method call, you wouldn't be able to use them in customized inbox views, or in workflow start conditions.
So, I suggest you implement each of the attributes, and let them call a common subroutine in your implementation program which sets the data (object-whatever-whatever). Then each attribute implementation just makes a perform call, and calls the SWC_SET_ELEMENT macro. Your subroutine can be as sophisticated or unsophisticated as you need/wish - e.g. checking whether there is any need to refresh the values if there is a lot involved in finding the values.

Raw material issue for inspection from inspection lot

Hello friends,
My sample size is fixed i.e.75 gm for all raw material quality testing. I have defined sampling procedure with sampling type "fixed sample". I want that this amount should be decreased from total lot quantity when i am posting it to unrestricted use. i.e. for 10 kg inspection lot quantity, 9.925 kg quantity should be posted .Now, system propose whole quantity for stock transfer from quality to unrestricted after usage decision.
Waiting for reply!
Thanks in advance!!

Dear Kiran
1) System doesnot take decimal in samples. if your basic unit is KG and you procure 10kg material system will consider sample amount as 1 kg. it will not take 0.075kg as the sample.
2) Other option is make the procurement in GMs but that will be difficult for purchaser to handle
3) or esle make use of this exit and do the posting based on that
QEVA0009 - UD: Predefinition of quantity to be posted to sample stock
This will help
Regards
Gajesh

GR durng final inspection - single inspection lot

Hello Friends,
In material master there is a key that control inspection lot creation during GR from purchasing is there any similar key for production too
Like below
For each purchase order item, batch and storage location
Thanks & Regards
Raj

Dear raju
Yes, You can use for 04 inspection ,
'X' An inspection lot for each order ,batch & storage location- An inspection lot is only created during the first goods receipt for each PO item or production order.
Regards
gajesh

How to set/change ip-address on ethernet interface

I have an IP address set on my wireless interface (with Internet access - no problem here), but I want to use my Ethernet interface to connect to a NAS device, on a "private/hidden" network - different network (10.0.1.xx)
What is the best way to do this?

Look in the printer's user manual for instructions on using TCP/IP (Ethernet.) The printer will have to connect to your network via an Ethernet port. If I remember correctly those old printers only have an AppleTalk serial port, so you will need an adaptor. They were called PhoneNet adaptors. I have no idea where you might find one today. They have a serial port connection on one end and an Ethernet connection on the other.
Unfortunately, I don't know that the printer will work unless you can turn on AppleTalk, and SL no longer supports it. If that's the case then you need a different type of adaptor - one that actively converts from AppleTalk to Ethernet. They were once made by Asante and Farallon, and they sold for around $100. But they are no longer made.

Set up IPMP Solaris 10 -- two interfaces, one IP

I have a tasking to set up failure-based IPMP on a T5120. I have been reading all the Sun documentation on setting up IPMP, but cannot find exactly what I am looking for. I have one IP address, and two connected NICs, and my task is to set up IPMP so that if e1000g0 fails, e1000g1 will take over. Is this possible, and if so, how?

If you have two interfaces and only want link-based failure detection, just put the group $YOUR_GROUPNAME statement in /etc/hostname.$INTERFACE file.
Say you have the two interfaces e1000g0 and e1000g1, your hostname is MyHostname and your group is MyGroup you would do the following:
put
MyHostname group MyGroup in /etc/hostname.e1000g0.
Put group MyGroup in /etc/hostname.e1000g1.
Either reboot the machine or manually configure ipmp:
ifconfig e1000g0 group MyGroup
ifconfig e1000g1 plumb group MyGroup up
in /var/adm/messages you there should be an info that no test-adress was given and that ipmp will operate in link-failure detection mode only.
Please note that officially you should create an ipmp instance first by issuing something like ifconfig $MyIPMP-Instance group MyGroup, but that step could be left out as ipmp instances are created implicitly.

How to set Camera Calibration as default??

I've calibrated my D300 with a Macbeth color chart, and got the altered values from the CS3 Calibration Script. I've entered these values in LR Develop Camera Calibration, then used Option->Set Default->Update to Current Settings. I didn't change any other settings, but now when I import images, they render with the previous White Balance, which came from the camera under incandescent lighting. Importing an outdoor image applies the same, now wrong, white balance. This is because I "Updated to current settings", to get the altered Camera Calibration. What am I doing wrong? I'm doing this in LR 2.0, but I assume 1.4.1 would do the same, no?

Jao -
Tint +5
Red -5
-3
Green -3
-15
Blue +5
-15
I used the modified script by ACR-Calibrator-L-V28. Prior to this, I got extreme settings so couldn't use them, but this script, along with more precise instructions worked. I shot the color chart in sunny conditions.
Dave - See above - LR2.0 printing with the 3800 works like 1.4.1. Perfect. I can't go back to LR 1.x. 2.0 is addictive. I just ignore the beta warnings. :-)
BTW In LR after changing JUST the Camera Calibration settings, use Option->Set Default to change calibration for just the camera you used on image selected in Develop. From then on, imported images from that camera will get the overridden calibration settings.

Inprocess inspection & 04 Inspection

Gurus,
When i am working with both 03 & 04,can i make GR for production order and take the material stock skipping 04 inspection?

When i am working with both 03 & 04,can i make GR for production order and take the material stock skipping 04 inspection?
Yes you can skip 04 inspection also.Also you can deactivate post to inspection for 04 inspection type.
But this is strange that you have activated 03 & 04 but still you want to skip the same.
Also remember you can use DMR in 04 also & skip the lot.
You can take mass UD in QA10.
Also you can use QA41 for scheduling.
Regards
Sujit

Inprocess inspection reassigning inspection plan

Hi,
I generated an inprocess inspection through 03 inspection type. But inspection characteristics where not there in the routing. Later I created inspection characteristics in routing.
When I tried to assign this task list by resetting sample calculation T Code- QAC3, it is saying confirmation already done.
Could anyone tell me how can I reset sample calculation and re assign my newly created routing.
I want to create an inspection lot with MIC's which I updated later or after confirmation.
I request anyone to help me.

Hi,
Follow the below any case for soln.
Case 1:
Go to CO02 (Production order change mode) enter order number
In order over view screen go to Function -> Inspection lot -> Delete and create and save the order. Now system will create the new inspection lot with new spec.
Case 2:
Go to Result screen for existing inspection lot click add characteristics icon add character one by one and do the result recording .
check and revert back.
Regards,
S.Babusingh

Setting applications to use specific network interfaces

How do I configure my computer such that specific applications will default to a different network interface than all the rest?
I want to set it up so that Adium always tries to use AirPort first and everything else uses ethernet if it's available.
Powerbook G4 1.5 Ghz Mac OS X (10.4.8) 1GB RAM

You can't (normally) get there from here.
What you're trying to do is affect the routing (route certain traffic through a specific interface). The issue is that routing works at the IP level, not the application level. This means that you can tell the system to route a.b.c.d (e.g. the address of the IM server you're connecting to) through a speciic router at w.x.y.z (e.g. the AirPort).
In order to do this, though, you need to have different IP address/subnet masks on each interface.
For example, assuming your wired ethernet is using 192.168.1.2/255.255.255.0 and your wired ethernet router is at 192.168.1.1, and your AirPort interface is using 10.1.1.2 with the AirPort router at 10.1.1.1 you can run the command:
<pre class=command>sudo route add a.b.c.d 10.1.1.1</pre>
and all traffic for a.b.c.d will go over the AirPort link.
Note that it doesn't matter what protocol you use - any traffic destined for a.b.c.d, whether it's AIM, HTTP, FTP or anything else - or what application you use - Adium, Safari, FireFox, etc. - they'll all use the AirPort link.
Note that this technique will NOT work if you have both interfaces on the machine configured in the same subnet, but this is not a supported configuration, so you shouldn't be doing that anyway.

Set up Calibration Inspection in Inspection Interface

Similar Messages

Maybe you are looking for