SIP Server FQDN missing

My phones will not connect to my Lync server. When I run the dhcputil - emulate my SIP Server FQDN is blank. I believe this entry comes from :
netsh dhcp server add optiondef 120 UCSipServer Binary 0 comment="Sip Server Fqdn"
But I have ran this with changing to my Lync server, but it still comes up blank.
Any ideas?
Thanks
Baze

Here's link for Configuring DHCP Options to Enable Sign-in for IP Phones that may be helpful as well
http://technet.microsoft.com/en-us/library/gg398088%28v=ocs.14%29.aspx
http://um.losrios.edu/network-config-to-support-the-lync-phones/
Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question, please click "Mark As Answer"
Mai Ali | My blog: Technical | Twitter:
Mai Ali

Similar Messages

Bea sip server 3.1 xml error:(

hi.i am a new this subject.i develop a instant messaging with SIP using java.But i have given error xml.When i start the sip server and enter the console.all xml files cannot process.why?i dont know configure the sip server? do i miss someone? pls help me:(
Error message is admin console:The template you provided at /WEB-INF/templates/form.xml could not be processed
The template you provided at /WEB-INF/templates/.xml could not be processed
The template you provided at /WEB-INF/templates/summarypage.xml could not be processed. and all xmls can not process.
Error message is start server prompt.
Error: 'Instruction unknown:loadinstruction' (but i is not seen.there small 2 instead of i)
Fatal Error: 'Could not compile stylesheet'
Can I load only web logic sip server 3.1 or can i load with other web logic server for example Oracle Web Logic Server 10.3?????????do they work with together??????????
Edited by: user13107827 on May 24, 2010 5:50 AM

As the Product Manager for the Oracle Communications Converged Application server (the former BEA WebLogic SIP server) and the former product manager for the Sailfin (I was PM for the Sailfin product before I left Ericsson to work for BEA) I must say that the Oracle product is absolutely superior, both in terms of quality and design, to any other competing product. I can also say that Oracle is fully behind this technology. Remeber that in the long run the issue is not "cost", but "value". Open source software is generally free for a reason.

CVP - SIP Server Groups and Redundant SIP Proxy (CUPS)

I am migrating from a CVP 7 + UCCE 7.5 solution which uses srv.xml files on the CVP servers to implement redundancy
from CVP to the SIP Proxies (which are CUPS based).
In the new CVP 8.5 + UCCE 8.5 solution, I am trying to set up equivalent redundancy, which
is now done via Server Groups.
The solution is geographically diverse, with one CVP server + a CUPS server (publisher) at Site1,
and the second CVP + CUPS server (subscriber) at site 2.
Previously (on CVP 7), I was able to configure each CVP server so that its priority was to use the CUPS server at its
"local" site. Hence there were 2 different srv.xml files, one for each CVP server.
To configure this in CVP 8.5, I would need 2 SIP Server groups, to give each CVP a group
configured to prefer the "local" CUPS server. But when I configure a SIP server group(s) pointing to CUPS, I seem to be only able
to get one single Server Group to work. That single Server Group only works if the server group name
matches exactly the Domain Name configured in CUPS. Since CUPS' Domain name is a single cluster wide name,
I can get only one Server Group working, not the two that I need.
So, where am I going wrong?
Regards.

Fairly new to CVP and had a question about how to configure the dialed number patterns so they point to more than 1 CUCM. My environment doesn't have a SIP Proxy or DNS Srv. That said, I tried to create as what was mentioned above - SIP Serve Group with 2 CUCM Subs then have a dialed number pattern point to it. However, when I initiate a call to an ICM script and eventually hit an agent, it flips between ready and reserve. When I change the dialed number pattern to point to a specific CUCM, it works fine. Followed all the aobve recommendations as well. Any idea how to make this work? Hoping I'm just missing something here...

Lync IM intergration without Server FQDN in Certificate

Hello All,
We have Exchange Server 2010 Sp2 and Lync Server 2013.
We need to intergrate Lync 2013 IM with Exchange 2010 owa.
But we are having below problem .
1) Our CAS certificates does not include the Server FQDN. ( Servername.contoso.local) , We canno't add this address in to 3rd party certificate.
How can we do this ?
regards

I'd suggest changing the URL of your EWS to use the same domain as your SIP domain (i.e cas.contoso.com) - presumably a valid internet domain. This is the recommended approach. You can follow the guidance here on doing that: http://technet.microsoft.com/en-us/library/aa997233(v=exchg.150).aspx
Once you have done this you can request a public CA certificate.
If this helped you please click "Vote As Helpful" if it answered your question please click "Mark As Answer"
Georg Thomas | Lync MVP
Blog www.lynced.com.au | Twitter
@georgathomas
Lync Edge Port Check (Beta)
This forum post is my own opinion and does not necessarily reflect the opinion or view of Microsoft, its employees, or other MVPs.

Deploying war file in weblogic SIP server 2.2

Hi,
I trying to deploy a "sar" file in weblogic SIP server,but it is not allowing me to do that.So one of my collegue told me to change the "sar" to "war" and try to deploy.
When i am trying to deploy that it is saying that unable to find deployment descripter WEB-INF/web.xml in the war file.Actually it is there.But i don't know why it is giving that error.
Actually i need to deploy "sar" file and i changed that file into "war" file
What are all the trail and error to solve this problem
(1)I made the "war" file from file folders.
suppose my application directory name is "myapp"
then i am going into the "myapp" folder and from there i am trying to make war file and it is having all the related class files , sip.xml file , web.xml file.
Then i tryed to deploy that file from weblogic SIP server 2.2.console.
(2) Next I included the weblogic.xml file also into the war file.
(3)The "sar" file working fine in SDS 3.1,but not in we blogic SIP server.
(4)The SDS3.1 is working with JRE 5 so i changed that JRE from 1.5 to jre 1.4. and again prepared the sar file and changed that SAR file to WAR file.
I created a domain in SIP server which was created in "user_projects."
For e.g., the domain name is "mydomain" and
the directory structure is
mydomain
|
|
|----------applications(dir)
|
|----------myserver(dir)
|
|----------rmfilestore(dir)
|
|----------sipserver(dir)
|
|-----------boot (file)
|
|-----------config.xml
|
|-----------startWeblogic
|
|-----------stopWebLogic
|
|----------upload-------xxxxmanager----META-INF---WEB-INF----log4j.properties
--------------sip.xml
-----------------web.xml
-------------weblogic.xml
web.xml, sip.xml,log4j.properties are under WEB-INF folder
Do i need to change any path setting in startWebLogic.cmd file.I didn't change any thing in the startWeblogic.cmd.
Since my war file is having all the related files like all the related "jar" files in that.
Any body's help will be appriciated.
Thanks
vish

Can any body please reply for above question.
Hi BEA support please flash some light on my above question
vkviswanadh

How to reset password of weblogic sip server 3.1

Hi ,
Can anybody help me in resetting the username/password of weblogic sip server 3.1
Thanks a lot
Regards
Saurabh

Hi,
If we have only one admin account available, I am afraid there is no means to reset the password other than reinstalling Windows. See this article as a reference:
What to do if you forget your Windows password
Besides, we may try to create the Windows 8.1 install media with the following article:
Create installation media for
Windows 8.1
How to perform a clean installation of Windows
And please note, if we do a clean install, we need to activate Windows again.
If Windows 8 came preinstalled on your computer, your product key should be on a sticker on your computer or with your documentation. Or we may contact the manufacturer for further help.
Best regards
Michael Shao
TechNet Community Support

NullPointer when invoke InitialContext in standard application sip server

I am unable to do a new InitialContext() in an application that does not have any sipservlets , but is deployed on sip server engine tier
When an application is deployed in weblogic engine server (sip server 3.1 ) without a sip.xml as the application does
Not have any sip servlets , a new InitialContext() throws a NullpointerException . The stack trace is below .
This error is not encountered in weblogic 9.2 server (non sip server)
InitialContext ic = new InitialContext();
javax.naming.NamingException [Root exception is java.lang.NullPointerException: SIP Servlet context not found]
at javax.naming.spi.NamingManager.getURLObject(NamingManager.java:588)
at javax.naming.spi.NamingManager.getURLContext(NamingManager.java:533)
at javax.naming.InitialContext.getURLOrDefaultInitCtx(InitialContext.java:279)
at javax.naming.InitialContext.lookup(InitialContext.java:351)
at

Hi B.,
have you managed to find the solution for this problem? I'm facing same issue.
I also tried to publish the WS in standalone app (via javax.xml.ws.Endpoint.publish()) and it worked with no problem that way. However, when I moved this to servlet definition, it failed.
Thanks a lot.
Regards,
F.

Dial-up connection between Asterik SIP server and Cisco 5400

Hi,
We have a setup for dial-up. The incoming call lands on Cisco 5400 and is forward to PGW using mgcp intergration. PGW sends it to Asterik SIP server over SIP. This Asterik Server sends it to another Cisco 5400 over SIP for Internet.
The issue is for some dial-up user, it works fine. But for some it doesn't. The problem is when we see the log on the last Cisco 5400, the incoming call tone is detected as FAX tone rather then Modem tone.
Any idea why is it so??

Hi,
We have a setup for dial-up. The incoming call lands on Cisco 5400 and is forward to PGW using mgcp intergration. PGW sends it to Asterik SIP server over SIP. This Asterik Server sends it to another Cisco 5400 over SIP for Internet.
The issue is for some dial-up user, it works fine. But for some it doesn't. The problem is when we see the log on the last Cisco 5400, the incoming call tone is detected as FAX tone rather then Modem tone.
Any idea why is it so??

SPA2002 in SIP server environment

Hello,
I am using the SPA2002 that registers remotely to a SIP server. The phones register correctly and can reach any other user agent (not SPA2002). the problem is that other user agents cannot call the SPA2002 until the SPA2002 calls first then the other US calls immediately. If other UA does not call the SPA2002 for about 10 minutes then calls to the SPA2002 will not be possible.
Did any one meet this problem before?

There is a setting "NAT Keep Alive Enable" which will send a message every 15 seconds or so to the SIP server to keep the router sip signalling port open. Did you try setting that field to yes?

P2P SPA3102 setup with no SIP server/service provider

Description:
- Peer-to-peer ATA connection with no service provider or SIP server
Location A (my location):
- Linksys SPA3102
- PABX analog device (Panasonic)
- Public and static IP
Location B (my partner location):
- D-Link DVG2001S
- Public IP
Questions:
- Can B ATA (D-Link) call to A ATA (Linksys) being different brands?
- Can I pick up the B ATA attached phone and directly to have PABX internal dial tone at A, for other extension or external calls?
- From PABX other extensions, can I call to SPA3102 extension number and directly redirect the call to B ATA?
I was read many .pdf documents about SPA setup, and try differents configuration, but I'cant make the communication with my partner location happens.
I think my problem is understanding and writing the correct PSTN LINE and LINE 1 Dial Plan parameters in my SPA3102.
Can I make it happens?
Thanks in advance,
Bitman
Message Edited by Bitman on 07-28-2007 05:37 AM

Good day! I just hope this is not one of those “.pdf documents” that you have already read but basically this should work if you’re setting up two SPA3000 or SPA3102 since they have exactly the same Voice configuration:
http://www.provu.co.uk/pdf/sipura/spa_backtoback_2x_spa3000.pdf
I’m guessing that IP dialing should work on your two units if they both support SIP, however, in this case, I haven’t tried setting up a D-Link before ( or you may try to wait for other users who happen to have a D-link also to post suggestions) , you may just want to try looking for documents on setting up IP dialing on D-link then try to match it’s IP dialing parameters with the SPA.

Final Cut Server (FCSvr) missing the Edit Proxies Device in the Advanced Administration Pane.

Final Cut Server (FCSvr) missing the Edit Proxies Device in the Advanced Administration Pane.
If for any reason an Admin has mistakenly or purposely deleted the Edit Proxies device
from the FCSvr Java Admin, and you'd like to restore connective to it following the instructions below.
Note verify these symptoms, open the FCSvr Java Admin, Go to Preferences and the Proxies Pane and inspect
If the field and drop down for Edit Proxies is missing please backup your FCSvr DB manually and following the steps below to restore connectivity.
1. From the Terminal from the following command
          cd /Library/Application\ Support/Final\ Cut\ Server/Final\ Cut\ Server.bundle/Contents/MacOS/
2. Next run the following command
           ./fcsvr_client getmd --xml /prefs/0 > ~/Desktop/prefs0.xml
This will output a XML file containing the Final Cut Server Global Preferences to the Desktop folder of the currently logged in user.
3. Using for favorite XML Text Editor (mine is TextMate) open the file that was output
4. Notice the XML element and attribute values between lines 29 and 31
<value id="PROXY_CLIP_EDIT_DEVICE">
   <address>/dev/3</address>
</value>
5. From the command line run the following command to determine the Device ID for you Edit Proxies device
./fcsvr_client search /dev
You should get an output similar to what's below.
Address        DEVICE_NAME                   DEVICE_TYPE
/dev/20        Edit Proxies                  contentbase
/dev/9         MEDIA                         filesystem
/dev/1         Proxies                       contentbase
/dev/2         Version                       contentbase
Record the new Device id for the Edit Proxies device.
6. Open up the file /Desktop/prefs0.xml and XML attribute in line 29
   <address>/dev/20</address>
to the value of the Edit Proxies from step 6.
7. Save the /Desktop/prefs0.xml
8. From the command line run the following command
sudo ./fcsvr_client setmd /prefs/0 --xml ~/Desktop/prefs0.xml
enter you admin password if prompted.
9. Close and reopen the FCSvr Java Admin, Go to Preferences and Proxies and inspect
The field and dropdown should reappear.
If for some reason this didn't work, feel free to contact me offline.
Nicholas Stokes
[email protected]

H.264 is a puzzling choice of codec for edit proxies. H.264 is not an edit-friendly codec since it is a complex long-GOP structure and will require a ton of rendering just to play back the timeline. ProRES 422 Proxy would be a much better choice for editing. I'm afraid I can't account for the differences between Compressor and FCServer in this case, but my gut tells me the non-I-frame codec you are trying to use for edit proxies might have something to do with it. Maybe for an edit-proxy workflow to operate properly on the server-side the codec must be I-frame? Is there any reason you do not want to use ProRES 422 Proxy? They are about 1/3 the footprint of 720p24 DVCPRO-HD, which is already very efficient. For that frame rate and frame size they would be roughly half the heft of good ol' DV25.
So my answer to all three questions would be to try ProRES 422 Proxy for your edit proxies and see if everything lines up.

BEA Sip Server 3.1 Socketexception

Hi All,
I am getting a SocketException on the multicast address specified for the Data and Engine Cluster while starting the managed servers in Weblogic SIP Server 3.1.
Does anyone know how to fix this?
Thanks !

As the Product Manager for the Oracle Communications Converged Application server (the former BEA WebLogic SIP server) and the former product manager for the Sailfin (I was PM for the Sailfin product before I left Ericsson to work for BEA) I must say that the Oracle product is absolutely superior, both in terms of quality and design, to any other competing product. I can also say that Oracle is fully behind this technology. Remeber that in the long run the issue is not "cost", but "value". Open source software is generally free for a reason.

Sh Application to test weblogic sip server 3.1

Is there any Sh application available to test weblogic sip server diameter domain?
I set up a diameter domain with hssclient only. The interface works fine. but I cannot find sh application to deploy.
just wondering where to get sh application example?
or is the application at diameter manageable? I meant that can I configure public id, HSS server and so on at admin console.
Thanks.

Hello,
You will need to test and recompile the application referencing the new Web Services .dlls for the BusinessObjects Enterprise version you plan to use.
There are some changes for example BusinessObjects Enterprise XI R3.1 uses Axis 2:
' Web Services URLs
Private WS_BASE_URL As String = "http://localhost:8080/dswsbobje/services/"
'NOTE: The following variables are case sensitive
'       Upper case for Axis 2.0 (BOE XI R3.1)
Private WS_URL_SESSION As String = WS_BASE_URL + "Session"
Private WS_URL_REPORTENGINE As String = WS_BASE_URL + "ReportEngine"
Private WS_URL_BIPLATFORM As String = WS_BASE_URL + "BIPlatform"
'       Lower case for Axis 1.1 (BOE XI R2)
'Private WS_URL_SESSION As String = WS_BASE_URL + "session"
'Private WS_URL_REPORTENGINE As String = WS_BASE_URL + "reportengine"
'Private WS_URL_BIPLATFORM As String = WS_BASE_URL + "biplatform"
Then deploy the application with the appropriate version of the Web Service .dlls.
The new documentation can be found at:
http://help.sap.com/businessobject/product_guides/boexir31/en/wssdk_dg_12_en.zip
and
http://help.sap.com/businessobject/product_guides/boexir31/en/wssdk_net_apiRef_12_en.chm
Elaine

Weblogic SIP server 3.1

how to use weblogic SIP server with X-lite?
because the x-lite's message "network not ready"
where the false?

I found answer to my question.
Yes it is available.
It is now “Oracle Communications Converged Application Server”

"Server Header" with Weblogic SIP Server 2.2

Hi All,
I'm using Weblogic SIP Server 2.2, based on Weblogic Server 8.1 SP5, and I want to desactivate the "Send Server Header" option.
I try to do it by using the console like describe in http://e-docs.bea.com/wls/docs81/ConsoleHelp/domain_server_protocols_http.html page. The config.xml file is modified ( <i><WebServer Name="myserver" SendServerHeaderEnabled="false"/></i>), but all response messages still contain the server header.
This header adds information about the version of WebLogic Server that is running. Which is a security leak.
It seem's that this problem is solved since Weblogic Server 8.1 SP4. But I don't succeed in turning the option off.
Any idea about this issue?
Thanks,
Karine.

Hi,
This problem is resolved by installing the new version of WebLogic SIP server (3.0 prÃ©views).
Thanks,
Karine.

SIP Server FQDN missing

Similar Messages

Maybe you are looking for