SNMP OID query
Not sure if this is the right forum for this.....
Doing a bit of work using SNMP for various things - need to know if there is a way to delete the VLAN.DAT file using SNMP - and if so what is the OID I need to use.
Thanks
You can use the CISCO-FLASH-MIB for this. You would set the following objects:
ciscoFlashMiscOpEntryStatus : 5ciscoFlashMiscOpDestinationName : "flash:vlan.dat"ciscoFlashMiscOpCommand : 3ciscoFlashMiscOpEntryStatus : 1
The file should then be deleted.
Similar Messages
-
I am trying to build a basic TCL skeleton script that reads a remote SNMP OID and displays the value on the screen.
I don't want it to be an EEM Event, I just want to run it from the (tcl)# prompt.
So I guess I'm asking if you can use cli_exec and other commands in the "namespace import ::cisco::eem::*" in a normal non-EEM script - can I do that?
This is the error I get:
OTN.159(tcl)#source flash:TCL_SNMP_Remote_Read.tcl
invalid command name "::cisco::eem::event_register_none" ^
% Invalid input detected at '^' marker.
What am I missing?
================= TCL_SNMP_Remote_Read.tcl ==============================
::cisco::eem::event_register_none
namespace import ::cisco::eem::*
namespace import ::cisco::lib::*
if [catch {cli_open} RESULT]
{ error $RESULT $errorInfo }
else { array set cli1 $RESULT }
if [catch {cli_exec $cli1(fd) "snmp get v2c 192.168.1.100 public timeout 1 oid 1.3.6.1.2.1.1.1.0" } RESULT]
{ error $RESULT $errorInfo }
else { set SnmpSysDesc $RESULT }
if [catch {cli_close $cli1(fd) $cli1(tty_id)} RESULT] {
error $RESULT $errorInfo
puts $SnmpSysDesc
=========================================================================
In the sho-run config I have:
event manager directory user policy "flash:/"
event manager session cli username "cisco"
Any help to get me started would be greatly appreciated!
TimIf you don't want an EEM policy, then don't use any of the EEM constructs. Instead, all you need is this:
set output [exec "snmp get v2c 192.168.1.100 public timeout 1 oid 1.3.6.1.2.1.1.1.0"]puts $output -
The cisco snmp oids do not work, I can't get cpu or memory data.
Hello. I want to monitor the cpu and memory usages on my cisco devices using snmp. I found the snmp oids related to cpu in the following page :
http://www.cisco.com/en/US/tech/tk648/tk362/technologies_tech_note09186a0080094a94.shtml
I just copy the table here:
But the oids in the table do not work on my devices. For example, I have a cisco 3550 switch with the ip 192.168.1.211, version 12.2(25)when I want to get the informations about the oids up in the table, I got these results:
It shows that the oids cisco given up in the table are not existed in my 3550 switch's MIB. More weird is that when i add a number "1" to
the end of the oid cisco given, I can get some meaningless data for some unkonwn item names like "entreprises.x.x".
For most mib items, the snmp oids work well on my switch. For example, the following graph shows the interface out rate of the swtich:
I think the essence is when I executed the following command:
in all the output results, there's not any item relevant with "cpu" or "memory", but most other items are ok, such as interfaces, as shown below:
IF-MIB::ifDescr.47 = STRING: FastEthernet0/39
IF-MIB::ifDescr.48 = STRING: FastEthernet0/40
IF-MIB::ifDescr.49 = STRING: GigabitEthernet0/1
IF-MIB::ifDescr.50 = STRING: GigabitEthernet0/2
IF-MIB::ifDescr.51 = STRING: Null0
IF-MIB::ifDescr.52 = STRING: Vlan1
IF-MIB::ifType.1 = INTEGER: ethernetCsmacd(6)
IF-MIB::ifType.2 = INTEGER: ethernetCsmacd(6)
IF-MIB::ifType.3 = INTEGER: ethernetCsmacd(6)
IF-MIB::ifType.4 = INTEGER: ethernetCsmacd(6)
IF-MIB::ifType.5 = INTEGER: ethernetCsmacd(6)
So why the cisco given oids won't work on my cisco switch, and how can I get the datas I want? Anyone has some advices? Thanks in advance!
In case the pictures I inserted missing, I attach my problem in the doc.Have you looked at this previous discussion:
Can't Activate FaceTime -
Snmp oids for the command "show counters interface intx/y delta"
Hello,
I have a question about SNMP OIDs for the command "show counters interface intx/y delta" on Catalyst6500. The customer wants to create graphs for the following values:Overruns, qos0Outlost, InErrors, OutErrors, InDiscards, OutDiscards etc..
Is possible to get these values using SNMP??
Thank you
RomanThank you, Dan. These OIDs are for the output from the command "show interface int x/y". But I think, that these OIDs are not for the command "show interface int x/y delta".
Roman -
Hello
Someone could tell me where to find a list of SNMP OIDs for solaris 8
thank you for your cooperationThank you, Dan. These OIDs are for the output from the command "show interface int x/y". But I think, that these OIDs are not for the command "show interface int x/y delta".
Roman -
Vpdn: searching for snmp oid to log out vpdn session
Hello colleagues,
Cisco 7204 works as vpdn server.
There are two problems:
1) I'm searching for snmp oid to log out , terminate vpdn session
2) radius server does not receives snmp statistics of incoming traffic of vpdn users.
Please is anyone able to assist me?
aaa new-model
aaa authentication login default local
aaa authentication ppp default group radius local
aaa authentication ppp VPDN local group radius
aaa authorization network default local group radius
aaa accounting delay-start
aaa accounting update periodic 3
aaa accounting exec default start-stop group radius
aaa accounting network default start-stop group radius
aaa session-id common
vpdn enable
vpdn-group 1
! Default PPTP VPDN group
description HOMENET
accept-dialin
protocol pptp
virtual-template 3
interface Virtual-Template3
ip unnumbered Loopback1
peer default ip address pool vpdn-pool
no keepalive
ppp authentication chap VPDN
snmp-server community xxxxxxx RW
snmp-server chassis-id 0x0E
snmp-server enable traps tty
radius-server host x.x.x.x auth-port 1812 acct-port 1813
radius-server timeout 60
radius-server key 7
radius-server authorization permit missing Service-Type
Best regards, Petr AkimovHello –
I received a reply from the developer of the script, and listed below is the new code that was suggested:
#!/bin/bash
value=`snmpwalk $1 -v1 -c $2 .1.3.6.1.2.1.25.1.5.0 | cut -d " " -f4`
if [[ value -gt $3 ]]
then
echo " $value Users Online, Critical!"
retval=2;
else
if [[ $value -gt $4 ]]
then
echo " $value users online, Warning!"
retval=1;
else
echo " $value Users online, fine."
retval=0;
fi
fi
exit $retval;
I checked the server in question, and there were two, 2, user logins active on the system. I ran the snmpwalk command, and the output was the following:
HOST-RESOURCES-MIB::hrSystemNumUsers.0 = Gauge32: 15
I then modified the script to include the above text, and ran it again. The output was the following:
15 users on line, Normal.
For some reason, the value of 12 appears to be that for no users logged into the system. I am not sure why that is the case.
If nothing else, progress has been made with the modification of the script. The snmp service that I have installed on the server is that which came bundled as a
feature with the server. The only thing that was not installed was the SNMP WMI Provider option. -
SG-500 - SNMP OID for CPU Load?
Hello,
i have several SG500 (Standalone and stacked). How can i get the CPU Load via SNMP? Who knows the correct SNMP OID for CPU Load?
In the MIB which are provided as download a wasn't able to find the correct OID.Hello,
There are three OIDs available for CPU usage:
CPU utilization for 5 seconds
.1.3.6.1.4.1.9.6.1.101.1.7.0
CPU utilization for 1 minutes
.1.3.6.1.4.1.9.6.1.101.1.8.0
CPU utilization for 5 minutes
.1.3.6.1.4.1.9.6.1.101.1.9.0
This came from a scrap note I had in an e-mail, so I am not exactly sure where this information is originally.
Let me know if that works for you,
Christopher Ebert - Network Support Engineer
Cisco Small Business Support Center
*please rate helpful posts* -
EEM detector SNMP OID does not work
i want to use EEM to detector policy-map class traffic rate, if class traffic is more than a number, trigger syslog message.
below is my EEm script on ASR1002 ( asr1000rp1-adventerprisek9.02.04.02.122-33.XND2.bin)
event manager applet Rate-limit
event snmp oid ".1.3.6.1.4.1.9.9.166.1.15.1.1.10.50.196608" get-type exact entry-op gt entry-val "100" poll-interval 10
action 1.0 syslog msg "policy Rate-limit"
but i did not see anything showing on syslog. from debug, i got below error msg :
Jun 1 02:21:49.160 GMT: fh_fd_snmp_process_async
Jun 1 02:21:49.160 GMT: fh_fd_snmp_process_poll_timer: re=0x3D144824, timer_type=POLL
Jun 1 02:21:49.160 GMT: fh_fd_snmp_process_poll_timer: OID unavailable, value check skipped
Jun 1 02:21:49.160 GMT: fh_fd_snmp_start_poll_timer: start_t=10000
but i could get number from snmpwalk command :
xchen-mac:~ xchen$ snmpwalk -v 2c -c <string> -m ALL stde1002a .1.3.6.1.4.1.9.9.166.1.15.1.1.10.50.196608
SNMPv2-SMI::enterprises.9.9.166.1.15.1.1.10.50.196608 = Counter64: 112938
please help me where is wrong ?Duplicate post.
Go here: https://supportforums.cisco.com/discussion/12219976/eem-detect-snmp-event-not-working -
SNMP OID on Catalyst 3750G & 3650G
Hallo guys,
we have a couple of 3750Gs and sveral 3650Gs in my company lan, and I'm looking for the SNMP OIDs supported with which the very basic status of these switches can be retrieved. I mean generic status like the switch is being active, or experiencing technical error etc...
I was advised to take 1.3.6.1.2.1.4.1.0 (IPForwarding), but I'm not sure if it is the right one. I'd appreciate if someone can give me a hint..
Thank you!
Li LuYour request is pretty generic. There are a lot of OIDs which can provide device health. You might want to start with ifInOctets, ifOutOctets, ifInErrors, and ifOutErrors. Those will give you per-port byte and error counts in both the ingress and egress directions.
As for whole-device help, take a look at the moduleTable from the CISCO-STACK-MIB. The object moduleStatus will tell you the status of the fixed switch itself. -
Cisco ASA SNMP OIDs (show name, show vpn-sessiondb l2l)
Hi all,
I am trying to figure out the SNMP OIDs that is equivalent to the following ASA commands:
show name
show vpn-sessiondb l2l
Thanks!im looking for the solution ? did u ever find out if this was possible?
-
What snmp OID to use to monitor control-plane of router
Hi there!
I've applied policy-maps on control-plane, based on cisco recomandation.
Now i need to know, what snmp OID i've to use to monitor them (i'm using zabbix)
Let me know.
Regards!If you are using IOS which uses a policy-map to configure Control Plane Policing then you are asking in the wrong place as this forum is for IOS-XR not IOS but you can poll objects in the CISCO-CLASS-BASED-QOS-MIB::cbQosPoliceStatsTable (for example cbQosCMDropByte64, cbQosPoliceExceededByte64, cbQosPoliceConformedByte64).
If you mean you have changed the LPTS policers to help protect the control-plane in IOS-XR then I believe there is currently no support for polling the counters via SNMP. See the section on monitoring in Xander's document https://supportforums.cisco.com/document/93456/asr9000xr-local-packet-transport-services-lpts-copp -
ASA 5512 - monitor power supply status via snmp oid
Device – ASA 5512 running 9.1(1).
Show version:
ASA-1# sh ver
Cisco Adaptive Security Appliance Software Version 9.1(1)
Device Manager Version 6.6(1)
Compiled on Wed 28-Nov-12 11:15 PST by builders
System image file is "disk0:/asa911-smp-k8.bin"
Config file at boot was "startup-config"
ASA-1 up 8 hours 38 mins
Hardware: ASA5512-K7, 4096 MB RAM, CPU Clarkdale 2792 MHz, 1 CPU (2 cores)
ASA: 2048 MB RAM, 1 CPU (1 core)
Internal ATA Compact Flash, 4096MB
BIOS Flash MX25L6445E @ 0xffbb0000, 8192KB
Issue: looking for a snmp OID to poll power supply status (Inbuilt Power Supply - no redundant power supply in this scenario). Possibly what we see in show environment.
CSE analysis:
I tried using the OIDs belonging to CISCO-ENTITY-FRU-CONTROL-MIB , like cefcFRUPowerOperStatus and cefcFRUPowerAdminStatus but it didn’t return anything.
NOTE: I have done all the snmp walks from the Linux server. Do I doubt it’s something to do from the snmp manager side.
Couple of observations. The CISCO-ENTITY-FRU-CONTROL-MIB talks about the field replaceable power supplies, so I doubt if it’s going to return the value for inbuilt power supply.
Second, I noticed that there are snmp traps supported for power supply and threshold setting. See configuration below. Is it that only traps works for power supply and environment related details?
Snmpwalk on cefcFRUPowerStatusEntry returns nothing:
[root@tonbenso-eagle bin]# ./snmpwalk -v2c -c public 172.16.169.29 1.3.6.1.4.1.9.9.117.1.1.2.1
SNMPv2-SMI::enterprises.9.9.117.1.1.2.1 = No Such Object available on this agent at this OID
Snmpwalk on cefcFRUPowerOperStatus returns nothing:
[root@tonbenso-eagle bin]# ./snmpwalk -v2c -c public 172.16.169.29 1.3.6.1.4.1.9.9.117.1.1.2.1.2
SNMPv2-SMI::enterprises.9.9.117.1.1.2.1.2 = No Such Instance currently exists at this OID
Snmpwalk on cefcFRUPowerAdminStatus returns nothing:
[root@tonbenso-eagle bin]# ./snmpwalk -v2c -c public 172.16.169.29 1.3.6.1.4.1.9.9.117.1.1.2.1.1
SNMPv2-SMI::enterprises.9.9.117.1.1.2.1.1 = No Such Instance currently exists at this OID
[root@tonbenso-eagle bin]#
login as: root
I tried polling the ciscoEntityFRUControlMIB to see what all values it return. It just returned enterprises.9.9.117.1.3.1.0 = INTEGER: 2. Meaning cefcMIBEnableStatusNotification is FALSE (value 2). Meaning cefcModuleStatusChange, cefcPowerStatusChange, cefcFRUInserted, cefcFRURemoved, cefcUnrecognizedFRU and cefcFanTrayStatusChange are prevented from being sent.
Snmpwalk on ciscoEntityFRUControlMIB
[1]+ Stopped ./snmpwalk -v2c -c public 172.16.169.29
[root@tonbenso-eagle bin]# ./snmpwalk -v2c -c public 172.16.169.29 1.3.6.1.4.1.9.9.117
SNMPv2-SMI::enterprises.9.9.117.1.3.1.0 = INTEGER: 2
Object
cefcMIBEnableStatusNotification
OID
1.3.6.1.4.1.9.9.117.1.3.1
Type
TruthValue
Permission
read-write
Status
current
MIB
CISCO-ENTITY-FRU-CONTROL-MIB ; - View Supporting Images
Description
"This variable indicates whether the system
produces the following notifications:
cefcModuleStatusChange, cefcPowerStatusChange,
cefcFRUInserted, cefcFRURemoved,
cefcUnrecognizedFRU and cefcFanTrayStatusChange.
A false value will prevent these notifications
from being generated."
Found couple of bugs:
CSCty32558 – but then this is for 5585 and I see it is fixed in 8.4
CSCul90037 – New state
Show snmp-server oidlist:
http://www-tac.cisco.com/Teams/ks/c3/getLargeFile.php?srId=632222409&fileName=20141030-013905_ASA-show-snmp-server-oidlist.txt
Show tech:
Sh run | in snmp:
ASA-1# sh run | in snmp
snmp-server host asa 172.18.123.228 community *****
no snmp-server location
no snmp-server contact
snmp-server community *****
snmp-server enable traps entity power-supply-presence power-supply-temperature -----à I was talking about this trap above
any help will be appreciated.Hi
I've got an ASA with redundant power supplies. An ASA5585. So I have the need to monitor them. :-) So how can we do it?
Also I've made a SNMP-Walk through the ASA v8.4(2)8 and it doesn't show up any ENV-MIB values. The
1.3.6.1.4.1.9.9.13 tree is not available. Are you shure it's available on the ASA?
Funny is also that the command "show snmp-server oidlist" from the 8.4 configuration guide is not available on the real CLI. I think the documentation guys were faster than the coders. ;-)
Kind regards
Roberto -
Problem using the SNMP OID to query the in use and available ds0 channels?
When using the MIB CISCO-POP-MGMT-MIB, particularly the OID .1.3.6.1.4.1.9.10.19.1.1.9.1.3.0.0 or .1.3.6.1.4.1.9.10.19.1.1.4
I have a pair of 2811 voice Gateways, both running IOS c2800nm-spservicesk9-mz.124-24.T4.bin
The value for active calls from 1 of the gateways is correct.
The value fromthe second is 4294967278
Has anyone seen this issue before, could it be a problem with firmware on the E1 card?
Can you check the firmware from the command line on the router.
Thanks
ColinUnfortunately, the POPM MIB is not fully supported on ISR platforms due to the triple numbering scheme of interfaces. See this thread for an alternative: https://supportforums.cisco.com/message/662852#662852 .
-
SNMP OID for DHCP on Server 2012
We recently installed Server 2012 standard on one of our servers and were trying to keep a graph of DHCP lease use. Anyway the OIDs for DHCP in Server 2008 R2 started with "1.3.6.1.4.1.311.1.3.2.1.1". If I try to snmpwalk these same OIDs on the new Server
2012 (We the DHCP server configured and active), I get:
Error in packet.
Reason: (genError) A general failure occured
Failed object: SNMPv2-SMI::enterprises.311.1.3.2.1.1
I'm using SNMPwalk and I've never had a problem with this before. Any idea what would cause this? Thanks!
Thanks!I'm having the same issue. OIDs just don't work against a 2012 DHCP server. I can snmpwalk other OIDs, just not DHCP :(
Firewall has been disabled (and there were already adequate snmp rules allowing the traffic). Since I can query other OIDs, I'm ruling out firewall.
Has this info been removed in 2012? -
Is there a single snmp oid for flash and dram ?
Does a single univeral oid (or 1 for flash and one for dram) exist that will provide total amount of flash and total amount of dram across all chassis families ?
ThanksThis link is your best bet:
http://www.cisco.com/warp/public/477/SNMP/contiguous_memory.html
Maybe you are looking for
-
Poor sound quality in timeline and export; fine in Source?
Hello all. Newbie to Pr but experienced pro in digital audio. I'm stumped and know I'm just missing something somewhere. I've made a music video for one of my songs. The graphics are all done (in AE), imported to Pr and eveything looks great. I impor
-
Hi, umm so anyways my ipod is about 2 years old now and i think the reason why it started to malfunction in the first place was because i had too much stuff on my ipod, apps, movies, and junk. But now i took it to the apple store and they were able t
-
Hi, is anyone experienced in boosting performance of large message processing in XI? I've got messages of about 3MB size. Their processing in XI takes about 5 minutes. The respective mappings are quite simple. I have seen that I can configure a speci
-
My Turbo-Saver (from Upromise.com) Add-on is incompatible with Firefox 5.0 and was disabled when I upgraded. i want to switch back to the previous version of Firefox where it is compatible.
-
I just tried to buy a song but it only let me gift it so I gifted it to myself. It was sent to my email. How to I redeem it so I can hear it and add it to my library? What happened to just buying a song? MJ2633