SNMP: Zone: Duplicate member error message
hello
customer trying to close zone under FM
and received following error message
any advice welcomed i didnt find any reference in documentation
JYP
SNMP: Zone: Duplicate member - RWSE-02A ZoneAliasList .1401.7
Sounds like the message is complaining about a zone with a duplicate member in it. You may want to open a command line session to each of the MDS and see if you can locate and delete any duplicate zone members. You should check all the MDS switches in the VSAN, because the duplicate member could be in any one of them.
Hope this helps,
Mike
Similar Messages
-
I have connected my time capsule to motorola SG6580 modem via ethernet. I have a wireless network on the motorola and a wireless network from the time capsule. I get duplicate IPs error messages (no connection) sometimes when trying to connect devices to the wireless network. How do I fix? Sometimes devices cannot connect to the network because of conflicting IPs. I look on the Motorola and every device has a unique IP assigned but occasionally a device has taken the IP of another device. I have been writing down all the devices and the IPs they have been using. It happens more with PCs than Macs, ipads or iPhones.
If the Time Capsule is set up correctly in bridge mode, then it is the responsibility of the Motorola modem/router to provide the correct IP address assignments for all devices on the network.
Check to insure that the Time Capsule is correctly set up to operate in bridge mode as follows:
On your Mac, open AirPort Utility
Finder > Applications > Utilities > AirPort Utility
Click on the Time Capsule icon, then click Edit in the smaller window that appears
Click the Network tab at the top of the next window
Insure that the setting for Router Mode is configured to read "Off (Bridge Mode)"
Once you have confirmed that the Time Capsule is configured correctly, everything else is the responsibility of the Motorola modem/router as far as network routing and IP address assignments for devices.
If you continue to have IP address issues, then you should contact the Internet Service Provider (ISP) that provided the Motorola device to you and ask them to fix the issue. -
Hi,
Does anyone know what a duplicate class error message means and how to resolve it?
It just does not make any sense to me as there is only one instance of the class yet the compiler is throwing out a duplicate class error message.I copied your experiment and had no trouble compiling the four classes (A, B, C, and Test). One thing to note is that Test.class shows up in the root destination directory (above a.b.c) because Test.java is missing the package statement. Perhaps, as mentioned earlier in the thread, the missing package statement is causing the problem with your compiler.
I compiled them with ant using the following build.xml code:
<?xml version="1.0" encoding="UTF-8"?>
<project basedir="." default="compile" name="PackageTest">
<property name="build.dir" location="build"/>
<property name="dist.dir" location="dist"/>
<target name="init">
<mkdir dir="${build.dir}/classes"/>
<mkdir dir="${dist.dir}"/>
</target>
<target name="compile"
depends="init"
description="Compile Source Code">
<javac srcdir="."
destdir="${build.dir}/classes"/>
</target>
</project> -
Planning 9.3 Duplicate member error: An object with the name 0000 already e
Hi All
I have 5 dimensions in my Planning applications namesly, Company, State, Product, Entity and Account
Company hase members called 0000(default) and 1000, 1001 etc
I also want add my Entity default member as 0000, but when I tried to add the memeber in my entity dimension I'm getting the Error : An object with the name 0000 already exists: Please help me to fix this
Thanks in AdvanceU won`t be able to add the duplicate item name to planning application untill it would be the 9.5 version.
By the way, NotPlanning App`s nothing like as scanty - they has already an option "Allow duplicate item names" in 9.3 version.. -
RH11 gives a duplicate file error message converting from RH9
My project has an empty file which cannot be deleted but was ignored by RH9. In converting to RH11 I get the following message: "Error - node */Views/<folder name>/<folder name>/SBLCRVAL.htm already exists." However, there is no other file by that name in the project. There is a similar one which I renamed and everything works fine in RH9, but I cannot convert to RH11.
Hi there
I think I'd save a copy of the offending file in a safe place, then delete it from the project. After the upgrade completes, then import it back into the project.
Cheers... Rick -
Duplicate error message when doing validation
hi am geting two same error when validation,i what to display only one error message
am in jdeveloper 11.1.1.6.0,am geting duplicate validation error message
this is how am doing validation
<af:inputText value="#{bindings.Organisationname.inputValue}"
simple="true"
columns="20"
maximumLength="#{bindings.Organisationname.hints.precision}"
shortDesc="#{bindings.Organisationname.hints.tooltip}"
id="it1" autoSubmit="true" required="true"
validator="#{pageFlowScope.orgvalidation.chkOrgName}"
label="Organisation Name">
<f:validator binding="#{bindings.Organisationname.validator}"/>
</af:inputText>
public String checkName(String orgname){
ResultSet rs;
Row curPerson;
String value= null;
OrgAppModuleImpl am =(OrgAppModuleImpl)ADFUtils.getApplicationModuleForDataControl("OrgAppModuleDataControl");
try {
System.out.println("valueadded "+orgname.toUpperCase());
value =am.findbyOrgname(orgname.toUpperCase().trim());
System.out.println("valueadded "+value);
catch (Exception e) {
e.printStackTrace();
return value;
public void chkOrgName(FacesContext facesContext, UIComponent uIComponent,
Object object) {
// Add event code here...
String value =(String)object;
String evalue= checkName(value);
if( evalue == null){
}else{
FacesMessage message = new FacesMessage();
message.setSeverity(FacesMessage.SEVERITY_ERROR);
message.setSummary("Organisation Name already exists.");
FacesContext context = FacesContext.getCurrentInstance();
context.addMessage("esecurity", message);
throw new ValidatorException(message);yes i what two diffirent validation which is required=true and checking for duplication this is not what am talking about,what am talking about is the two message for duplicate validation for checking duplicate,am geting this message twice in the error message
public void chkOrgName(FacesContext facesContext, UIComponent uIComponent,
Object object) {
// Add event code here...
String value =(String)object;
String evalue= checkName(value);
if( evalue == null){
}else{
FacesMessage message = new FacesMessage();
message.setSeverity(FacesMessage.SEVERITY_ERROR);
message.setSummary("Organisation Name already exists.");
FacesContext context = FacesContext.getCurrentInstance();
context.addMessage("esecurity", message);
throw new ValidatorException(message); -
My iPod Classic won't sync--I keep getting error messages.
I have an iPod Classic (Late 2009) that's about a year and a half old. It just started refusing to sync with iTunes. I have a PC, and when I plug the iPod in, the computer wants to scan and fix the iPod. Whether I let it or not--I've done it both ways, multiple times--when I open iTunes, iTunes says I need to restore my iPod. It restores without glitching. But when I try to re-sync my library, I get 200-400 songs in and get an error message that a specific song can't be synced because of "error [numerical error]." I've seen "Error -50" a lot, but not always. It doesn't always get stuck on the same song, artist, or album--just somewhere in the B's, something goes wrong. At the beginning, I was seeing a "duplicate file" error message, but I haven't seen it the last 5-7 times I've gone through the restore-resync process.
I've tried manually managing the content, but the same thing happens. If it doesn't get stuck on a song, it'll say "Finishing Sync" for ages--until I have to force-quit iTunes and manually eject the iPod.
I have reinstalled iTunes--not 100%, but using their "find and replace faulty parts" option. I have an iPhone, and it syncs with no problem, and I my iTunes library itself is functioning totally normally. However, iTunes freezes a lot when I'm trying to fix this problem with my iPod, including when I first plug it in. I've had to force-quit iTunes multiple times because of this.
This all started because my iPod was skipping from about 10 seconds into one song to the next in the playlist. I figured something was wonky with the last sync, so I went to restore my iPod. When I plugged it in, I noticed that there was a software update, so I did that--I can't remember if I restored, then did the update, or the other way around. But nothing has worked since then.
It must be a problem with the iPod itself that the restore just isn't erasing, but I'm not sure where that leaves me. Help?This could be an indication or a damaged or dying hard drive. I would recommend doing a disk diagnostic on the iPod's HD using the instructions given by turingtest2 in this older thread. He also covers what the resulting numbers indicate.
https://discussions.apple.com/thread/3784647?start=0&tstart=0
B-rock -
Hi,
While trying to open the order in co03, co02, I am getting the below error message : Inconsistent data : order 107434 16.09.2013, duplicate entry o 0020 is showing. Please guide me the way forward.
Regards,
Mastan.Hi Mastan
The report mentioned by Rajen should clear the inconsistent records.
Please observe that you could have found this by yourself report with a quick note search for this error message or even searching for old threads.
Even a google search points to the solution.
You should do your own research before opening such kind of thread.
BR
Caetano -
Just receive an unlocked 3gs iphone from a family member and can't unlock the screen. Can't restore iphone because of error message.Now what do I do?
What do you mean by unlock the screen? Is there a passcode set on the iPhone? If so and this is from a family member, can that family member give you the passcode? If it has been forgotten then you must retore from recovery mode per http://support.apple.com/kb/HT1212
-
Hiding the #error message from a member column
Hey guys,
The issue is mainly the member formula column showing the basic #error message in the cell upon intentionally messing with the values. It's pretty natural, but I'm looking to hide that error message, though I forgot how. I'm sure it's pretty simple.
I'm using Hyperion 11.1.2.1.0.83
Thanks again!
Edited by: 922290 on 20-Mar-2012 22:40
Edited by: 922290 on 20-Mar-2012 22:51You could have a look at the following post to get some ideas, it is not exactly the same issue but may help Re: #error in formula row of the form sum([1])/2
There is also the IsError function, more info at http://docs.oracle.com/cd/E17236_01/epm.1112/hp_admin/apcs03s09.html
Cheers
John
http://john-goodwin.blogspot.com/ -
How to avoid 'duplicate data record' error message when loading master data
Dear Experts
We have a custom extractor on table CSKS called ZCOSTCENTER_ATTR. The settings of this datasource are the same as the settings of 0COSTCENTER_ATTR. The problem is that when loading to BW it seems that validity (DATEFROM and DATETO) is not taken into account. If there is a cost center with several entries having different validity, I get this duplicate data record error. There is no error when loading 0COSTCENTER_ATTR.
Enhancing 0COSTCENTER_ATTR to have one datasource instead of two is not an option.
I know that you can set ignore duplicates in the infopackage, but that is not a nice solution. 0COSTCENTER_ATTR can run without this!
Is there a trick you know to tell the system that the date fields are also part of the key??
Thank you for your help
PeterAlessandro - ZCOSTCENTER_ATTR is loading 0COSTCENTER, just like 0COSTCENTER_ATTR.
Siggi - I don't have the error message described in the note.
"There are duplicates of the data record 2 & with the key 'NO010000122077 &' for characteristic 0COSTCENTER &."
In PSA the records are marked red with the same message (MSG no 191).
As you see the key does not contain the date when the record is valid. How do I add it? How is it working for 0COSTCENTER_ATTR with the same records? Is it done on the R/3 or on the BW side?
Thanks
Peter -
I'm trying to burn a dvd from idvd but I keep getting error message, broken assets, but when I check my drop zones and their content there's no error messages on any of them?
Hi
And if You change view - in main "window/view field" so that You see the box-plot structure.
No exclamation marks there either ?
and non at the front page ?
iDVD do not copy Your material - only points to where it is stored. So if on any external hard disks, USB-memories, CDs or DVDs are missing - assetts are broken.
Or if You changed location of any material or directed iPhoto or iTunes or GarageBand to a new Library - Then iMovie/iDVD also get's lost.
Yours Bengt W -
i keep getting an error message when trying to sync my iphone in itunes, "duplicate file name specified." Anyone have any help? Please??
You can try going to iTunes with your device connected, select your device, then click view, show duplicate items
-
i get an error message when trying to sync my reset ipod "The iPod ...cannot be synced. A duplicate file name was specified."
Locate the photos folder which is selected for syncing with the device and delete the folder iPod Photo Cache inside.
tt2 -
I am unable to sync to my ipod. Error message states "unable to sync because duplicate file name exist". Any ideas on how to remedy this problem?
Were some of the songs purchased from a different itunes account?
Maybe you are looking for
-
The item can't be moved because AirPort Time Capsule can't be modified
have just set up my new airport time capsule done a time machine back up but can not add any files to it to share when i try i get the following message "The item can't be moved because AirPort Time Capsule can't be modified" how do i change this ma
-
Can't recover from recovery partition with OneKey after disastrous Win 8.1 upgrade
I have a U410 that is only a couple months old. A few days ago I decided to take the plunge and accept the free upgrade to Windows 8.1. Big mistake. SInce the upgrade, I've had a slew of problems ranging from programs not running to hard disk integri
-
I need to update my iphone 3g to ios 4.3
My friend gave me an Iphone 3 16gb but I need to update to the ios 4.3. Does anyone know how i go about doing that. Thanks
-
Is Apple TV able to connect to more then one tv
I was wanting to get Apple TV but I have 3 TVs can I connect Apple TV to all of them or do I have to buy a seaprate Apple TV for each tv.
-
Compaq Presario Desktop, IJ750 (Inkjet)
Hi, I am having problems with my computer printer in which it is jamming. I cannot buy another printer to replace it because I am told that they no longer make Compaq printers or inkjet printers anymore. Is it worth keeping my computer because I am