Software version 5 - Issues?

After updating to software version 5 - it freezes on step 4 of 5 - I have restarted both the laptop and the itouch but to no avail - any suggestions?

Go to documents<pictures<find iPod photos and delete all photo cache documents. Then close iTunes, unplug your iPod. Then plug in your iPod and launch iTunes and try to sync.

Similar Messages

7936 not showing software version and vlan issue

I have a 7936 that does not show the software version. I have installed the newest load on the callmanager, but still cannot see what version it is running on the phone.
My main issue with the phone is that I have to set the switchport access vlan to the voice vlan, if I try to let the phone use the swithport voice vlan, it will pull an IP address off of the data vlan and not the voice vlan.
Any help with either of these issues would be greatly appreciated. I do rate all helpful posts.
Thanks,
Robert

Hi Robert,
Here is some info that may help;
Verifying Firmware Version Information
You can obtain information about the firmware version installed on the IP Conference Station.
Follow these steps to verify the firmware version on an IP Conference Station:
Step 1 Press the Menu button.
Step 2 Press the Up or Down scroll button to select the Admin Setup menu.
Step 3 Press the Select button.
Step 4 Enter the administrator password. (The default administrator password is **#.)
Step 5 Press the Enter softkey.
Step 6 Press the Up or Down scroll button to select System Information.
Step 7 Press the Select button.
Step 8 Press the Up or Down scroll button to select SW Version.
The firmware version number is displayed.
Or if that is not working try accessing this way;
Using the Web Interface
Follow these steps to access the Cisco IP Conference Station 7936 web interface:
Step 1 Open your web browser.
Step 2 In the address field enter:
http:// IP address of the IP Conference Station:
Configuration information applies to the specific IP Conference Station associated with the IP address you enter.
Note If you changed the HTTP port number, you need to use that number as a suffix to the IP address. If you did not change the HTTP port number, then you do not need to enter a suffix.
The web interface appears, and the initial login page is displayed.
Step 3 To log in as the administrator, enter the administrator password and click Login.
The default administrator password is **#.
Note When logged in to the IP Conference Station web pages, the web pages will time out after approximately 20 minutes of inactivity. You will then have to log back in.
Step 4 To log off, click Administrator Logout.
Information Available on All Web Pages
The top right portion of the Cisco IP Conference Station 7936 web interface includes a separate section that displays consistent information for all of the web pages.
This section contains the following information; example text appears next to each item in the list:
Software Version: 3.3(2.00)
Protocol Type: SCCP
Boot Load ID: PC0503031418
Application Load ID: CMTERM_7936.3-3-2-0
IP Address: 10.1.1.11
MAC Address: 00c742655892
Local Number: 2022
As far as the VLAN issue goes, this has always been the case for our 7935's as well and I'm sure the 7936 is the same.
Switchport mode access
Switchport access VLAN XXX
Hope this helps!
Rob
Please remember to rate helpful posts........

The screen on my iPhone turned into an xray like display. With the assistance from Apple Support, I Upgraded the software version. But still did not resolved the issue.

The screen on my iPhone turned into an xray like display. With the assistance from Apple Support, I Upgraded the software version. But still did not resolved the issue.

Probably a setting. Look at the manual.
iPhone User Guide (For iOS 4.2 and 4.3 Software)

Restarting issue (partially solved) - Software version 1.2

Some users have mentioned a problem with their Ipods restarting on their own for no reason. It has also been suggested that this problem might be triggered by certain songs. I have had the same problem since updating to software version 1.2, AND I HAVE IDENTIFIED THE SIMILARITY IN ALL OF MY PROBLEMATIC MP3'S...
THEY ARE ALL ENCODED IN MONO
I do not have any other type of file besides MP3's on my IPOD, and as of yet, I have not had this restarting problem with ANY of my files EXCEPT FOR EVERY ONE of them that is in MONO (as opposed to stereo).
When I have some time I will try to RE-encode these songs in Stereo, and reload them into my Ipod to see what will happen. But I'm going on vacation for a week and will not be able to do this for over a week. If anyone out there has the time, please try this and let us know how it works out.
For the time being, I am removing EVERY file that is encoded in Mono from my Ipod, and hopefully this problem will disappear.

I am experiencing the same problem and this solution does NOT work:
1. From the Start menu, choose Control Panel.
2. Open the Internet Options control panel.
3. Click the Connections tab.
4. Click the LAN Settings button.
5. Select the Automatically detect settings checkbox.
6. Click OK in both windows.
7. Reopen iTunes and connect your iPod.
8. Update or Restore your iPod.
Any other helpful solutions, puh-leez???

Remote Desktop - The Remote Desktop administrator software does not match the installed client software version.

Hi,
I just upgraded to Mavricks and get this when I try to launch Remote Desktop:
The Remote Desktop administrator software does not match the installed client software version.
I tried removing the application and reinstalling it to no avail. Any suggestions?
Thanks.
-David J. Eisen

Hi coold88!
I have an article for you that addresses your issue:
Remote Desktop 3: How to install Remote Desktop Administrator software after the client software has been updated
http://support.apple.com/kb/HT3596
You will want to make sure you have the latest version of the software as well:
About Apple Remote Desktop 3.7
http://support.apple.com/kb/HT5896
Thanks for using the Apple Support Communities. Have a good one!
-Braden

I have iphone 3gs 16 gb. after i downloaded software version 5.0, my phone stopped working. it keeps saying that the phone doesnt have a simcard.

I got a message that " iphone software version 5.0 is available" for my iphone. After i updated it, i got a message that my iphone could not be activated and to try to connect to itunes which i did, but i got a message that my phone has no sim card. Even with a sim card inside, my phone says that there's "No service." What happened? Help!!!

Yes, I tried. But nothing is working. I am feeling bad as such a costly phone stop working in 1.4 year ?
I am just sharing my experience.
I am not ranting but yes angry as I am eligible for upgrade in Nov 2012 so don't want to pay $149 for replacement as I can upgrade to iPhone 5.
Apple expert please help me how can I fix it. It's completely software issue.

Bluetooth bug in OS 10.0.10.672 (software version 10.0.10.85)

Hi there,
It appears that the latest release of the software has introduced a nasty Bluetooth bug. Before this release my Z10 worked perfectly fine with my HandsFree Link in my 2006 Acura TL. However, since I installed the latest OS release 10.0.10.672 (software version 10.0.10.85) I can pair with the vehicle however any call in or out causes the Bluetooth connection to be instantaneously dropped. The device simply cannot manage a conversation. Please note that the device itself does not disconnect (it is still paired), but it cannot service any audio between the vehicle and the Z10. Restoring to an older release of the OS fixes this issue.
Is there any way to get this resolved at all?
Please advise.
Thanks!

When my wife returns with our 2008 Odyssey with HandsFree Link I'll give it a try. I know it was working before I upgraded, as well. I'll post back later this evening.
1. Please thank those who help you by clicking the "Like" button at the bottom of the post that helped you.
2. If your issue has been solved, please resolve it by marking the post "Solution?" which solved it for you!

Certain apps will not install on my iPod touch 1G due to software version

I bought an iPod Touch 1G off a friend recently. When I got it off him, it had several versions of Angry Birds which all functioned perfectly. Since having to erase all the data and the apps on the device in order to sync it to my computer, I don't seem to be able to install Angry Birds at all and when I try, I get an error message saying I need to update the software version to iPhone 4.
According to my iTunes it is currently on the latest software version which is 3.1.3.
I don't understand why I can't install applications that were working fine before I synced the device to my computer. Could it be some cross-platform issue between my friends Mac and my Pc?
If anyone has a solution, I would be grateful as this is getting frustrating.

First of all, the 1st generation Touch can only instal and use up to iOS 3.1.3, even though there are later versions of the iOS available for newer iPod Touchs. The 1G simply isn't capable of using iOS 4.
As for Angry Birds, there appear to be six versions available (in the UK store), three are paid for and three are free. However, of the three free versions, two require iOS 4.0 or higher to run. So the versions installed on your iPod when you bought it must have been paid for or Angry Birds Lite. I assume therefore that you have been trying to instal Angry Birds Free and Angry Birds Rio Free, which both require iOS 4.0.
I have no idea why there are six different versions or why some require a higher version of the software than other versions.
So either try installing the Angry Birds Lite or buy one of the other versions. Be aware though, that if a version you buy then gets updated and subsequently requires iOS 4, it will be removed from your Touch (as it will not work).

Nokia N97 software version 11.X.021 released

Nokia N97 software version 11.X.021 released This software release includes significant improvements in the software stability, especially email, imaging, USB detection, widget stability and display transitions. To enable you to get the most out of your Nokia N97, the release also includes an Ovi store client. Further application updates will become available soon

After update, the issue of "when receive a call and the device is key locked, when you pick the phone it still shows that somebody calling in the screen, even after hanging up". we should reboot the phone.
I supposed this firmware fixed the problem, but I think my confiance to Nokia is decreasing

IPod touch wheel and iPod software version 1.5

Hi,
I have a problem with my iPod touch wheel (20 GB).
I have purchased some music on the iTMS this days, but i was unable to transfer it to my Ipod, which software version was 1.4.
So, I decide to restore the iPod with the latest version for this model, i.e. 1.5, and to upload all the songs, using the automatically update option.
I did it, but after uploading the music, all the playlists are empty (menu "playlists", "artists", etc...). I can't see any songs although the indication of size is correct.
But, everything seems normal when I access the iPod by iTunes (version 5) : I can see and play all the playlists on the iPod, when I have deactivate the automatically update.
So, I restore again the iPod, and transfer manually some playlists. I was able to browse them on the iPod, and listen to them.
I'm using iTunes 5, on Mac OS X 10.4.2.
Has anyone had the same problem ?

Maybe:
Restore loop (being prompted to restore again after a restore successfully completes)
Troubleshoot your USB connection. If the issue persists, out-of-date or incorrectly configured third-party security software may be causing this issue. Please follow Troubleshooting security software issues. .
Next try placing in DFU mode and then restoring.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
Then try restoring on another computer.
Last, make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar

HT1349 New software versions of iTunes and Safari hanging my XP system.

I have updated my software versions of iTunes and Safari in response to update message. Upgraded software is now causing my XP system to hang. It looks as if neither of the new versions can access the internet.

In the course of your troubleshooting to date, have you worked through the following document?
Apple software on Windows: May see performance issues and blank iTunes Store

Connector specific error - blackberry bold 9790 - desktop software version 6.1 and outlook 2010

Hi there
I've recently upgraded my business partners' outlook from 2007 to 2010. In doing so we've had a corrupt profile which we have had to delete and then replace with a new one. In doing so his outlook started working again but now his blackberry isn't synching the calendar entries.
Here's the basics:
- Bberry model - Bold 9790
- Bberry operating system - Blackberry's latest (7.1 I think)
- Blackberry desktop software 6.1 - this is intentional as we have found in the newer version of hte desktop software that we cannot map our teamsite calendar from outlook and sync the entries
- Outlook version 2010
- Calendars we are trying to sync are a personal one from a pst folder and a teamsite one from sharepoint linked to our microsoft exchange set up.
The error we are getting is a 'connector specific error'
I have worked with him to create the PTtrace.log and tif.log files. I've gotten reams of pages; but the errors on todays date (when the problem began) have come up with error 4238, 113, and 12. We have tried un-installing and re-installing 6.1 as well and no luck. We have re-set the configuration setup and re-mapped folders; chosen the new outlook profile, etc and still keep getting same error.
I'm now starting to think that there is a problem with the mapi profile as a start and wonder if outlook needs to repair itself or whether we are getting the error because of a duplicate entry somewhere (though if you asked me to tell you where from the logs I couldn't identify it).
I'm litterally tearing my hair out because my poor business partner lives and dies by his blackberry. Really want to try to get this resolved; but need some help and suggestions as I've tried most of the main causes and fixes.
Any assistance would really be appreciated so I can put him and myself out of our misery.
Thanks in advance.
Cel

Hi and Welcome to the Community...apologies for the delayed reply...hopefully you already have this resolved, but just in case!
Thank you for the thorough report...that helps tremendously. Sadly, though, none of the errors you listed reveal anything useful when I search the public KBs...perhaps you will be more lucky
http://btsc.webapps.blackberry.com/btsc/microsites/microsite.do
Even though it sounds like you may have done all or part of this, I encourage you to research the process in this thread:
http://supportforums.blackberry.com/t5/Desktop-Software-for-PC/Cleanly-quot-Starting-Over-quot-with-...
It starts with a process for cleanly starting over, and there is some discussion, and there is also a post (15) with links to older Desktop Software versions, if those are needed. Note that this is not, by any means, guaranteed to work...but it has worked for many to resolve issues they are having.
Your suspicion about the MAPI Profile may well be warranted, in which case this KB might be useful.
KB02083 How to create a Microsoft Outlook MAPI profile
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Trying backup and install software version 7.0 Bundle 2416

I can't help but have the same problem trying backup and install software version 7.0 Bundle 2416?   Anyone got any ideas - my 9900 is now completely unusable and is stuck on "Backing Up Your Data"!!

Hi and Welcome to the Community!
RIM is constantly changing, due to many many reasons (some of which are licensing), the compatible PIMs for the Desktop Software. I've no idea what prior version supported CardScan, but the current KB regarding compatibility is here:
KB12268Applications supported by BlackBerry Desktop Software for Windows for synchronization
You can find some older versions of the Desktop Software in this archive:
http://www.blackberryforums.com/rim-software/253387-archived-rim-desktop-software.html#post1744114
Good luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4   Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA   Display/Scan Bar Code

TS3694 I'm trying to update my iphone 3g with software version from 2.2.1 (5H11) to 2.2.1 and an unknown error occurred (-1)

I'm trying to update my iphone 3g with software version from 2.2.1 (5H11) to 2.2.1 and an unknown error occurred (-1)

eepereira wrote:
an unknown error occurred (-1)
That Error message is indicative of a Hardware issue. The Device may need Service. Take it in for evaluation.

I want to update my computer to the newest software version

I want to update my computer to the newest software version I have 10.6.8 but I am not sure if all of my files will delete. What will happen if I update?

With any update/upgrade you should always do a back up first.
If you have files that have been done on a Clssic Mac platform, they need Rosetta to run, this only runs on SL.
So consider that, also some older versions of iWork...have some issues as well.
But your machine should be able to run Mavs.
Here are the system Specs:
http://support.apple.com/kb/HT5842

Software version 5 - Issues?

Similar Messages

Maybe you are looking for