[Solved] No Route to Host but Internet is fine
Hi, Im trying to install tcpdump and getting this error;
bash-3.2# pacman -S tcpdump
resolving dependencies...
looking for inter-conflicts...
Targets (1): tcpdump-3.9.8-1
Total Download Size: 0.26 MB
Total Installed Size: 0.57 MB
Proceed with installation? [Y/n] y
:: Retrieving packages from extra...
error: failed retrieving file 'tcpdump-3.9.8-1-i686.pkg.tar.gz' from mirrors.uk2.net : File unavailable (e.g., file not found, no access)
warning: failed to retrieve some files from extra
error: failed to commit transaction (unexpected error)
Errors occurred, no packages were upgraded.
bash-3.2#
So thinking the host might be down, I pinged it
[jamie@myhost ~]$ ping -c 3 mirrors.uk2.net
PING mirrors.uk2.net (83.170.64.14) 56(84) bytes of data.
64 bytes from mirrors.uk2.net (83.170.64.14): icmp_seq=1 ttl=58 time=14.7 ms
64 bytes from mirrors.uk2.net (83.170.64.14): icmp_seq=2 ttl=58 time=22.6 ms
64 bytes from mirrors.uk2.net (83.170.64.14): icmp_seq=3 ttl=58 time=14.6 ms
--- mirrors.uk2.net ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 2009ms
rtt min/avg/max/mdev = 14.616/17.317/22.623/3.753 ms
[jamie@myhost ~]$
Looks fine, so I tried another mirror
bash-3.2# pacman -S tcpdump
resolving dependencies...
looking for inter-conflicts...
Targets (1): tcpdump-3.9.8-1
Total Download Size: 0.26 MB
Total Installed Size: 0.57 MB
Proceed with installation? [Y/n] y
:: Retrieving packages from extra...
error: failed retrieving file 'tcpdump-3.9.8-1-i686.pkg.tar.gz' from www.mirrorservice.org : Connection timed out
warning: failed to retrieve some files from extra
error: failed to commit transaction (unexpected error)
Errors occurred, no packages were upgraded.
bash-3.2#
Again no good, and again ping works fine
bash-3.2# ping -c 3 www.mirrorservice.org
PING www.mirrorservice.org (212.219.56.134) 56(84) bytes of data.
64 bytes from www.mirrorservice.org (212.219.56.134): icmp_seq=1 ttl=55 time=17.8 ms
64 bytes from www.mirrorservice.org (212.219.56.134): icmp_seq=2 ttl=55 time=24.4 ms
64 bytes from www.mirrorservice.org (212.219.56.134): icmp_seq=3 ttl=55 time=30.0 ms
--- www.mirrorservice.org ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 2006ms
rtt min/avg/max/mdev = 17.805/24.100/30.052/5.008 ms
bash-3.2#
Any ideas?
Edit: So its fixed now, for some reason /etc/resolv.conf was pointing to my router dns server, which barely works, after setting it back to my local one its working.
Last edited by jamie112 (2008-09-08 16:06:50)
It might help you figure out what's different when
you connect with telnet vs. when you connect
with a Java program. That difference might give
you a clue as to what you need to do differently
in your program to make it work.
Perhaps it insists that the source port number
is in the "privileged" range?
Similar Messages
-
Telnet can't figure out route to host, but only on certain ports?
This only occurs under 10.5. In 10.4.11, I can hit the server on both ports through telnet.
telnet <server> 510
Trying <server>...
telnet: connect to address <server>: Connection refused
telnet: Unable to connect to remote host
telnet <server> 80
Trying <server>...
Connected to <server>.
Escape character is '^]'.
fetch
HTTP/1.1 400
Date: Sun, 06 Jul 2008 03:06:15 GMT
Content-Type: text/html
<html><head><title></title></head>
<body>
fetch: 0
</body></html>
Connection closed by foreign host.
Here's the strangest part:
ping <server>
PING <server> (ip): 56 data bytes
ping: sendto: No route to host
^C
--- <server> ping statistics ---
1 packets transmitted, 0 packets received, 100% packet loss
How come it can figure out the route when using port 80, but not when using port 510? And is the inability to figure out the route the reason why Wireshark shows ZERO outgoing packets on port 510 when it fails to connect?
And why only on certain IPs? If I use "edu.yorku.ca", I can connect via telnet on both 80 and 510.orangekay wrote:
So it works if you supply a FQDN but not an IP? Are you certain that the IP you're using is valid? There may be some DNS trickery going on behind the scenes.
No, it only connects when I hit the server on port 80. Using IP or FQDN doesn't seem to make a difference.
If I try to use Network Utils to do a trace route, it too says no route to host.
I've got a G4/ppc running 10.4.11 attached to the same router, and it has no issue hitting the server on any port, and can do a trace route as well. -
WRT45GC - Not connecting to NTL Broadband, but internet works fine minus the router
I seem to have a problem try to get my WRT45GC to work as an accesspoint for my NTL connection. If the modem is plugged directly into my PC via ethernet cable, internet works fine. But if I plug my WRT45GC into the modem then have a direct connection to my pc from the router, i only get limited or no connectivity.
Also once this has been set up my laptop can pick up the wireless network but once again no internet.
I have been told different things by different people ie, the modem and router may have the same IP address, the router may not have DCHP enabled ( I dont have the IP address to log onto the router) please can someone help
If i unplug the router and have the modem connecting directly to the pc, internet works fine again.if u have a cable connection....follow the steps below
1) connect the computer to one of the LAN ports on the router...and connect the modem to the router's internet port.
2) check the ip add on the computer . to check the ip add go to start -> run -> cmd -> ipconfig...ensure that u have an ip add of 192.168.1.x and default gateway 192.168.1.1
2) access the router using http://192.168.1.1 . Keep the username blank and the default password is "admin".
3) go to the "mac add clone" subtab , enable it and click clone your pc's mac..save the settings....do a power cycle
4) go to the "wireless" tab , change the ssid , channel - 1 or 11.
If this does not work for u , revert back with the details - ISP name , cable / DSL , internet ip add off of the status page on the router.... -
VPN Client can't reach router or hosts, but can reach other connected sites.
We have a VPN client configuration on a 2901 router. The client passes authentication and connects fine. When connected, cannot reach the 2901 or any devices directly behind it, BUT can reach routers and hosts that are connected to the same 2901 through site to site connections.
Few notes:
I have added some lines excluding NAT in a few different ways, but does not resolve.
I have switched the RAP rool from 10.96.20.x to 172.21.20.x and can then connect to the local host. Appears to be a routing issue to the 10.x network, but I can't seem to find the solution.
Any help would be greatly appreciated. Here is the config:
boot-start-marker
boot system flash
boot system flash:c2900-universalk9-mz.SPA.153-2.T.bin
no ip domain lookup
ip inspect log drop-pkt
ip inspect name FIREWALL tcp
ip inspect name FIREWALL udp
ip inspect name FIREWALL ftp
ip inspect name FIREWALL fragment maximum 256 timeout 1
ip inspect name FIREWALL ntp
ip inspect name FIREWALL pptp
ip inspect name FIREWALL dns
ip inspect name FIREWALL l2tp
ip inspect name FIREWALL pop3
ip inspect name FIREWALL icmp router-traffic
no ipv6 cef
crypto isakmp policy 1
encr aes
authentication pre-share
group 2
crypto isakmp policy 5
encr 3des
authentication pre-share
group 2
crypto isakmp policy 10
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp policy 95
authentication pre-share
group 2
crypto isakmp policy 99
hash md5
authentication pre-share
group 2
crypto isakmp policy 110
hash md5
authentication pre-share
crypto isakmp client configuration group VPN-RAS
key *********
dns 10.96.17.2 10.1.200.50
wins 10.96.17.2 10.1.200.50
domain mine.com
pool RAPOOL
acl SPLIT
save-password
split-dns mind.com
netmask 255.255.255.0
crypto isakmp profile USERS
match identity group VPN-RAS
client authentication list DOMAIN
isakmp authorization list VPN-RAS
client configuration address respond
keepalive 300 retry 5
crypto ipsec transform-set AES128 esp-aes esp-sha-hmac
mode tunnel
crypto ipsec transform-set 3DES esp-3des esp-sha-hmac
mode tunnel
crypto ipsec transform-set DES esp-des esp-md5-hmac
mode tunnel
crypto ipsec transform-set 3DES-MD5 esp-3des esp-md5-hmac
mode tunnel
crypto ipsec transform-set DES-SHA esp-des esp-sha-hmac
mode tunnel
crypto ipsec transform-set myset esp-3des esp-sha-hmac
mode tunnel
crypto dynamic-map dynmap 1
set transform-set AES128
set isakmp-profile USERS
crypto map COMPANY_VPN 10 ipsec-isakmp
set peer *******
set transform-set 3DES-MD5
match address PA-VPN
qos pre-classify
crypto map COMPANY_VPN 50 ipsec-isakmp
set peer ******
set transform-set AES128
match address VPN
qos pre-classify
crypto map COMPANY_VPN 999 ipsec-isakmp dynamic dynmap
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
ip address 37.222.111.224 255.255.255.248
ip access-group INBOUND in
no ip redirects
no ip unreachables
no ip proxy-arp
ip verify unicast reverse-path
ip flow ingress
ip flow egress
ip nat outside
ip inspect FIREWALL out
ip virtual-reassembly in
duplex auto
speed auto
no cdp enable
no mop enabled
crypto map COMPANY_VPN
interface GigabitEthernet0/1
no ip address
ip flow ingress
duplex auto
speed auto
interface GigabitEthernet0/1.17
description LAN
encapsulation dot1Q 17
ip address 10.96.17.253 255.255.255.0
ip access-group OUTBOUND in
ip flow ingress
ip flow egress
ip nat inside
ip virtual-reassembly in
standby 0 ip 10.96.17.254
standby 0 priority 110
standby 0 preempt
standby 0 track 1 decrement 20
interface GigabitEthernet0/1.27
description VOICE
encapsulation dot1Q 27
ip address 192.168.17.254 255.255.255.0
ip access-group OUTBOUND in
ip helper-address 10.96.17.2
ip flow ingress
ip nat inside
ip virtual-reassembly in
h323-gateway voip bind srcaddr 192.168.17.254
ip local pool RAPOOL 10.96.20.50 10.96.20.150
ip forward-protocol nd
ip nat inside source route-map NAT-POOL interface GigabitEthernet0/0 overload
ip route 0.0.0.0 0.0.0.0 37.222.111.223
ip route 10.96.16.0 255.255.255.0 10.96.17.250
ip route 172.22.1.0 255.255.255.0 10.96.17.250
ip route 172.22.2.0 255.255.255.0 10.96.17.250
ip route 172.22.3.0 255.255.255.0 10.96.17.250
ip route 192.168.16.0 255.255.255.0 10.96.17.250
ip access-list extended DMZ
deny ip any 10.0.0.0 0.255.255.255
deny ip any 192.168.0.0 0.0.255.255
permit ip any any
ip access-list extended GUEST
deny ip any 10.0.0.0 0.255.255.255
deny ip any 192.168.0.0 0.0.255.255
permit ip any any
ip access-list extended INBOUND
deny ip 80.25.124.0 0.0.0.255 any
deny ip 10.0.0.0 0.255.255.255 any
deny ip 172.16.0.0 0.15.255.255 any
permit udp host 173.239.147.114 any eq isakmp
permit esp host 173.239.147.114 any
deny ip 192.168.0.0 0.0.255.255 any
permit udp any host 37.222.111.224 eq isakmp
permit udp any host 37.222.111.224 eq non500-isakmp
permit esp any host 37.222.111.224
ip access-list extended NAT
deny ip 10.96.20.0 0.0.0.255 any
deny ip any 10.96.20.0 0.0.0.255
permit ip 192.168.0.0 0.0.255.255 any
permit ip 10.0.0.0 0.255.255.255 any
ip access-list extended NONAT
permit ip any 192.168.0.0 0.0.255.255
permit ip any 10.0.0.0 0.255.255.255
ip access-list extended OUTBOUND
deny udp any host 22.55.77.106 eq isakmp
deny udp any host 22.55.77.106 eq non500-isakmp
deny esp any host 22.55.77.106
permit ip any any
ip access-list extended PA-VPN
permit ip 10.0.0.0 0.255.255.255 10.96.18.0 0.0.0.255
permit ip 10.0.0.0 0.255.255.255 192.168.18.0 0.0.0.255
permit ip 192.168.0.0 0.0.255.255 10.96.18.0 0.0.0.255
permit ip 192.168.0.0 0.0.255.255 192.168.18.0 0.0.0.255
ip access-list extended SPLIT
permit ip 10.0.0.0 0.255.255.255 any
permit ip 192.168.0.0 0.0.255.255 any
ip access-list extended VPN
permit ip 10.96.16.0 0.0.0.255 10.0.0.0 0.255.255.255
permit ip 10.96.17.0 0.0.0.255 10.0.0.0 0.255.255.255
permit ip 10.96.18.0 0.0.0.255 10.0.0.0 0.255.255.255
permit ip 10.96.0.0 0.0.255.255 192.168.0.0 0.0.255.255
permit ip 10.96.0.0 0.0.255.255 10.0.0.0 0.255.255.255
permit ip 192.168.16.0 0.0.0.255 192.168.0.0 0.0.255.255
permit ip 192.168.17.0 0.0.0.255 192.168.0.0 0.0.255.255
permit ip 192.168.18.0 0.0.0.255 192.168.0.0 0.0.255.255
permit ip 192.168.17.0 0.0.0.255 10.0.0.0 0.255.255.255
permit ip 192.168.18.0 0.0.0.255 10.0.0.0 0.255.255.255
permit ip 172.22.0.0 0.0.255.255 10.0.0.0 0.255.255.255
permit ip 172.22.0.0 0.0.255.255 192.168.0.0 0.0.255.255
route-map NAT-POOL deny 5
match ip address NONAT
route-map NAT-POOL permit 10
match ip address NATWe have a VPN client configuration on a 2901 router. The client passes authentication and connects fine. When connected, cannot reach the 2901 or any devices directly behind it, BUT can reach routers and hosts that are connected to the same 2901 through site to site connections.
Few notes:
I have added some lines excluding NAT in a few different ways, but does not resolve.
I have switched the RAP rool from 10.96.20.x to 172.21.20.x and can then connect to the local host. Appears to be a routing issue to the 10.x network, but I can't seem to find the solution.
Any help would be greatly appreciated. Here is the config:
boot-start-marker
boot system flash
boot system flash:c2900-universalk9-mz.SPA.153-2.T.bin
no ip domain lookup
ip inspect log drop-pkt
ip inspect name FIREWALL tcp
ip inspect name FIREWALL udp
ip inspect name FIREWALL ftp
ip inspect name FIREWALL fragment maximum 256 timeout 1
ip inspect name FIREWALL ntp
ip inspect name FIREWALL pptp
ip inspect name FIREWALL dns
ip inspect name FIREWALL l2tp
ip inspect name FIREWALL pop3
ip inspect name FIREWALL icmp router-traffic
no ipv6 cef
crypto isakmp policy 1
encr aes
authentication pre-share
group 2
crypto isakmp policy 5
encr 3des
authentication pre-share
group 2
crypto isakmp policy 10
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp policy 95
authentication pre-share
group 2
crypto isakmp policy 99
hash md5
authentication pre-share
group 2
crypto isakmp policy 110
hash md5
authentication pre-share
crypto isakmp client configuration group VPN-RAS
key *********
dns 10.96.17.2 10.1.200.50
wins 10.96.17.2 10.1.200.50
domain mine.com
pool RAPOOL
acl SPLIT
save-password
split-dns mind.com
netmask 255.255.255.0
crypto isakmp profile USERS
match identity group VPN-RAS
client authentication list DOMAIN
isakmp authorization list VPN-RAS
client configuration address respond
keepalive 300 retry 5
crypto ipsec transform-set AES128 esp-aes esp-sha-hmac
mode tunnel
crypto ipsec transform-set 3DES esp-3des esp-sha-hmac
mode tunnel
crypto ipsec transform-set DES esp-des esp-md5-hmac
mode tunnel
crypto ipsec transform-set 3DES-MD5 esp-3des esp-md5-hmac
mode tunnel
crypto ipsec transform-set DES-SHA esp-des esp-sha-hmac
mode tunnel
crypto ipsec transform-set myset esp-3des esp-sha-hmac
mode tunnel
crypto dynamic-map dynmap 1
set transform-set AES128
set isakmp-profile USERS
crypto map COMPANY_VPN 10 ipsec-isakmp
set peer *******
set transform-set 3DES-MD5
match address PA-VPN
qos pre-classify
crypto map COMPANY_VPN 50 ipsec-isakmp
set peer ******
set transform-set AES128
match address VPN
qos pre-classify
crypto map COMPANY_VPN 999 ipsec-isakmp dynamic dynmap
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
ip address 37.222.111.224 255.255.255.248
ip access-group INBOUND in
no ip redirects
no ip unreachables
no ip proxy-arp
ip verify unicast reverse-path
ip flow ingress
ip flow egress
ip nat outside
ip inspect FIREWALL out
ip virtual-reassembly in
duplex auto
speed auto
no cdp enable
no mop enabled
crypto map COMPANY_VPN
interface GigabitEthernet0/1
no ip address
ip flow ingress
duplex auto
speed auto
interface GigabitEthernet0/1.17
description LAN
encapsulation dot1Q 17
ip address 10.96.17.253 255.255.255.0
ip access-group OUTBOUND in
ip flow ingress
ip flow egress
ip nat inside
ip virtual-reassembly in
standby 0 ip 10.96.17.254
standby 0 priority 110
standby 0 preempt
standby 0 track 1 decrement 20
interface GigabitEthernet0/1.27
description VOICE
encapsulation dot1Q 27
ip address 192.168.17.254 255.255.255.0
ip access-group OUTBOUND in
ip helper-address 10.96.17.2
ip flow ingress
ip nat inside
ip virtual-reassembly in
h323-gateway voip bind srcaddr 192.168.17.254
ip local pool RAPOOL 10.96.20.50 10.96.20.150
ip forward-protocol nd
ip nat inside source route-map NAT-POOL interface GigabitEthernet0/0 overload
ip route 0.0.0.0 0.0.0.0 37.222.111.223
ip route 10.96.16.0 255.255.255.0 10.96.17.250
ip route 172.22.1.0 255.255.255.0 10.96.17.250
ip route 172.22.2.0 255.255.255.0 10.96.17.250
ip route 172.22.3.0 255.255.255.0 10.96.17.250
ip route 192.168.16.0 255.255.255.0 10.96.17.250
ip access-list extended DMZ
deny ip any 10.0.0.0 0.255.255.255
deny ip any 192.168.0.0 0.0.255.255
permit ip any any
ip access-list extended GUEST
deny ip any 10.0.0.0 0.255.255.255
deny ip any 192.168.0.0 0.0.255.255
permit ip any any
ip access-list extended INBOUND
deny ip 80.25.124.0 0.0.0.255 any
deny ip 10.0.0.0 0.255.255.255 any
deny ip 172.16.0.0 0.15.255.255 any
permit udp host 173.239.147.114 any eq isakmp
permit esp host 173.239.147.114 any
deny ip 192.168.0.0 0.0.255.255 any
permit udp any host 37.222.111.224 eq isakmp
permit udp any host 37.222.111.224 eq non500-isakmp
permit esp any host 37.222.111.224
ip access-list extended NAT
deny ip 10.96.20.0 0.0.0.255 any
deny ip any 10.96.20.0 0.0.0.255
permit ip 192.168.0.0 0.0.255.255 any
permit ip 10.0.0.0 0.255.255.255 any
ip access-list extended NONAT
permit ip any 192.168.0.0 0.0.255.255
permit ip any 10.0.0.0 0.255.255.255
ip access-list extended OUTBOUND
deny udp any host 22.55.77.106 eq isakmp
deny udp any host 22.55.77.106 eq non500-isakmp
deny esp any host 22.55.77.106
permit ip any any
ip access-list extended PA-VPN
permit ip 10.0.0.0 0.255.255.255 10.96.18.0 0.0.0.255
permit ip 10.0.0.0 0.255.255.255 192.168.18.0 0.0.0.255
permit ip 192.168.0.0 0.0.255.255 10.96.18.0 0.0.0.255
permit ip 192.168.0.0 0.0.255.255 192.168.18.0 0.0.0.255
ip access-list extended SPLIT
permit ip 10.0.0.0 0.255.255.255 any
permit ip 192.168.0.0 0.0.255.255 any
ip access-list extended VPN
permit ip 10.96.16.0 0.0.0.255 10.0.0.0 0.255.255.255
permit ip 10.96.17.0 0.0.0.255 10.0.0.0 0.255.255.255
permit ip 10.96.18.0 0.0.0.255 10.0.0.0 0.255.255.255
permit ip 10.96.0.0 0.0.255.255 192.168.0.0 0.0.255.255
permit ip 10.96.0.0 0.0.255.255 10.0.0.0 0.255.255.255
permit ip 192.168.16.0 0.0.0.255 192.168.0.0 0.0.255.255
permit ip 192.168.17.0 0.0.0.255 192.168.0.0 0.0.255.255
permit ip 192.168.18.0 0.0.0.255 192.168.0.0 0.0.255.255
permit ip 192.168.17.0 0.0.0.255 10.0.0.0 0.255.255.255
permit ip 192.168.18.0 0.0.0.255 10.0.0.0 0.255.255.255
permit ip 172.22.0.0 0.0.255.255 10.0.0.0 0.255.255.255
permit ip 172.22.0.0 0.0.255.255 192.168.0.0 0.0.255.255
route-map NAT-POOL deny 5
match ip address NONAT
route-map NAT-POOL permit 10
match ip address NAT -
Browsers not working but internet is fine
I've been having a weird issue for a few days, my computer is connected to the internet and I am able to login a messenger and use spotify and other programs that run through wifi but for some reason none of my internet browsers open any page. If anyone knows how to fix this please help!
Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test. -
Not connecting to Music Store or Software Updates (but Internet works fine)
About a month ago, I moved in to a new apartment and set up a new cable internet connection. After a very frustrating installation process (Netgear is not very Mac-friendly), the Internet worked. A couple days later, I realized I couldn't get onto the iTunes Music Store. It just tries for a while and then says it can't reach it and for me to check my Network Diagnostics.
I tried to get to the music store when I was at work on an Ethernet connection (as opposed to my usual wireless), but that didn't work either. I also realized today that my Software Updates aren't working, because they cannot connect either. It just tells me to click on Network Diagnostics, which I always do to no avail.
Also tonight, I realized I only have 4.5 GB space left on my computer. This computer is less than a year old, and I don't see how this is possible. I deleted a lot of things, and that didn't make any difference. Could I possibly have a virus? I thought Macs didn't even get viruses!? What should I do?I got this message from you, but I still have the same problem of not being able to connect to the iTunes store, software updates, Safari, CDDB, Help, Southwest's Ding, my weather widget, and several other things. I found a post you did in July where you helped someone else who it sounded like had the same problems that I am having. However, I tried your approaches to that -- isolating the problem (it affects all accounts on this computer), typing in that number (17.254.3.183) in Safari (says the server stopped responding), and now I really hope I don't have to back up everything and start over. I think this started when I moved to this apartment and set up a new Comcast cable internet account. I have been able to live with it because I have a computer at work and spend most of my time there anyway, but at times when I want to burn CDs, it really drives me crazy. Do you recommend taking it to the Apple store or would you be able to help me? Thanks.
-
Airport Extreme Blinking Amber But Internet Working Fine Multiple Status Messages
I have Airport Extreme 5.6.1. It started blinking amber showing Airport did not have a valid Internet Address. I was concerned about with changing anything if I could still connet. Checked a forum and it suggested to go to sheck status and see the problem. I did and now I have a new mesage. No DNS server address. I am hesitant about doing anything because if I do and lose internet connection I am really up a creek without a paddle.
Just to update. I unplugged my modem for a short time. When it powered up the light was green on my Airport Extreme.
-
[SOLVED] Cannot resume from suspend but hibernate works fine
Please help me figuring out what can be the issues..
I cannot resume from suspend while "sudo pm-hibernate" works fine..
When I use "sudo pm-suspend", the system (samsung N210 netbook) goes to sleep and I can see the power light blinking as expected. But, when I try to resume the system from suspend by pressing the power button, the screen remains black with no HDD activity. Only thing I can see is the power LED on.
After I do "sudo pm-suspend" and try to resume from suspend but fails. So, I do a HARD reboot and then this is the content of /var/log/pm-suspend.log
Initial commandline parameters:
Thu Dec 16 12:00:27 IST 2010: Running hooks for suspend.
Running hook /usr/lib/pm-utils/sleep.d/00logging suspend suspend:
Linux archlinux-N210 2.6.36-ARCH #1 SMP PREEMPT Fri Dec 10 20:32:37 CET 2010 x86_64 Intel(R) Atom(TM) CPU N450 @ 1.66GHz GenuineIntel GNU/Linux
Module Size Used by
dm_mod 66662 0
rfcomm 34874 4
sco 8828 2
bnep 8726 2
l2cap 42585 16 rfcomm,bnep
ipv6 281833 24
nls_utf8 1288 0
cifs 242984 0
fscache 39915 1 cifs
fuse 64259 3
arc4 1378 2
snd_seq_dummy 1431 0
snd_hda_codec_realtek 275887 1
uvcvideo 61404 0
videodev 64318 1 uvcvideo
v4l1_compat 15578 2 uvcvideo,videodev
ecb 2041 2
snd_seq_oss 28760 0
ath9k 80424 0
joydev 10055 0
btusb 11385 2
v4l2_compat_ioctl32 10212 1 videodev
bluetooth 52419 9 rfcomm,sco,bnep,l2cap,btusb
snd_seq_midi_event 5436 1 snd_seq_oss
mac80211 196159 1 ath9k
ath9k_common 3624 1 ath9k
ath9k_hw 290909 2 ath9k,ath9k_common
snd_hda_intel 22285 1
snd_hda_codec 79384 2 snd_hda_codec_realtek,snd_hda_intel
ath 8822 2 ath9k,ath9k_hw
snd_seq 50082 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
snd_seq_device 5297 3 snd_seq_dummy,snd_seq_oss,snd_seq
snd_pcm_oss 39221 0
cfg80211 143110 3 ath9k,mac80211,ath
snd_hwdep 6110 1 snd_hda_codec
uhci_hcd 21926 0
easy_slow_down_manager 3185 0
snd_mixer_oss 17106 2 snd_pcm_oss
snd_pcm 71921 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss
snd_timer 19265 2 snd_seq,snd_pcm
cpufreq_powersave 958 0
sky2 46293 0
rfkill 15882 3 bluetooth,cfg80211
led_class 2331 1 ath9k
snd 57562 11 snd_hda_codec_realtek,snd_seq_oss,snd_hda_intel,snd_hda_codec,snd_seq,snd_seq_device,snd_pcm_oss,snd_hwdep,snd_mixer_oss,snd_pcm,snd_timer
psmouse 52592 0
cpufreq_ondemand 8215 2
soundcore 5969 2 snd
ehci_hcd 36988 0
tpm_tis 7928 0
shpchp 26453 0
sg 25652 0
phc_intel 9527 1
battery 10231 0
tpm 10957 1 tpm_tis
samsung_backlight 2844 0
serio_raw 4486 0
snd_page_alloc 7249 2 snd_hda_intel,snd_pcm
usbcore 137570 5 uvcvideo,btusb,uhci_hcd,ehci_hcd
ac 3105 0
pci_hotplug 24319 1 shpchp
tpm_bios 5505 1 tpm
i2c_i801 8550 0
freq_table 2323 2 cpufreq_ondemand,phc_intel
pcspkr 1819 0
thermal 12242 0
evdev 8519 14
processor 25936 1 phc_intel
mperf 1243 1 phc_intel
ext4 313574 1
mbcache 5722 1 ext4
jbd2 69002 1 ext4
crc16 1297 2 l2cap,ext4
sd_mod 25856 4
ahci 20353 3
libahci 17982 1 ahci
libata 156316 2 ahci,libahci
scsi_mod 124891 3 sg,sd_mod,libata
i915 321187 3
drm_kms_helper 25963 1 i915
drm 175314 3 i915,drm_kms_helper
i2c_algo_bit 4911 1 i915
button 4834 1 i915
i2c_core 18726 6 videodev,i2c_i801,i915,drm_kms_helper,drm,i2c_algo_bit
video 19305 1 i915
output 1940 1 video
intel_agp 29459 2 i915
total used free shared buffers cached
Mem: 2046212 603128 1443084 0 11400 258660
-/+ buffers/cache: 333068 1713144
Swap: 2250748 0 2250748
/usr/lib/pm-utils/sleep.d/00logging suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/00powersave suspend suspend:
/usr/lib/pm-utils/sleep.d/00powersave suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/01grub suspend suspend:
/usr/lib/pm-utils/sleep.d/01grub suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/01laptop-mode suspend suspend:
/usr/lib/pm-utils/sleep.d/01laptop-mode suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/11netcfg suspend suspend:
/usr/lib/pm-utils/sleep.d/11netcfg suspend suspend: success.
Running hook /etc/pm/sleep.d/20_samsung-tools suspend suspend:
/etc/pm/sleep.d/20_samsung-tools suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/49bluetooth suspend suspend:
/usr/lib/pm-utils/sleep.d/49bluetooth suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/75modules suspend suspend:
/usr/lib/pm-utils/sleep.d/75modules suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/90clock suspend suspend:
/usr/lib/pm-utils/sleep.d/90clock suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/91wicd suspend suspend:
/usr/lib/pm-utils/sleep.d/91wicd suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/94cpufreq suspend suspend:
/usr/lib/pm-utils/sleep.d/94cpufreq suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/95led suspend suspend:
/usr/lib/pm-utils/sleep.d/95led suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/98video-quirk-db-handler suspend suspend:
Kernel modesetting video driver detected, not using quirks.
/usr/lib/pm-utils/sleep.d/98video-quirk-db-handler suspend suspend: success.
Running hook /usr/lib/pm-utils/sleep.d/99video suspend suspend:
/usr/lib/pm-utils/sleep.d/99video suspend suspend: success.
Thu Dec 16 12:00:31 IST 2010: performing suspend
Since, the last time I checked about suspend was 1.5 months back, I cant really make out as to what package caused the issue as I had a few upgrades since that time.
I am no expert but it seems like it is the log of suspending the system, it seems like the system didnt even go to initial stage of resuming.
Last edited by shadyabhi (2010-12-27 17:54:19)Well this is a long shot... But my laptop had some issues with suspending due to low-power governors preventing it from fully working at times.
Because of that I manually suspend with the following script:
#!/bin/bash
clear
cpufreq-set -g performance
cpufreq-info
echo "Continue? y/n? ";read bevestiging
if [ $bevestiging = "y" ]
then
echo "System going down for suspension NOW!"
pm-suspend
else
echo "Exiting..."
exit 0
fi
exit 0
All it really does in the end, is change the governer from which it's currently on to "performance", thus allowing maximum clock speed.
I've also added in a little confirmation dialog to check whether it's properly switched.
Of course, this will only work for you if you're also using laptop-mode and cpufrequtils.
Edit: You need to run this script with sudo or as the root user.
Last edited by Aeva (2010-12-16 14:16:32) -
My site doesn't work when I upload to my own web host, but it's fine in Preview or BC. Why?
I have uploaded my site via FTP to my own web hosting and my site is broken. My menus and slideshows don't work, my styles are all missing... everything is shifted to the left. What has happened and how can I fix it?
lanistudio, while the symptom of your change may appear to be correct behavior, I believe your fix is incorrect.
The original code is correct. The way slideshows work is that the original image source is to a very small animated gif that provides the preloader graphic until the actual image is loaded. All the images in a slideshow that are not visible when the page is first loaded are loaded by JavaScript running in the background. That JavaScript copies the "data-src" attribute into the "src" attribute once the image data is available. In this way a page with a slideshow load much more quickly in the browser.
If images in a slideshow where failing to load for you, I suspect the Adobe Tech's feedback was accurate and one or more of your .js files is missing, in the incorrect location or in a folder with incorrect permissions. If you provide the URL for your site after doing a clean upload from Muse (to get rid of any post export hand editing of the code) we can diagnose the root cause of the problem.
If you've ever used a method other than Muse's File > Upload to FTP Host... to upload, delete, rename, move or otherwise alter what's on your hosting, then you need to turn on the "Upload: All Files" option within the Upload to FTP Host... feature in order for Muse to be able to upload everything so it has an accurate understanding of what needs to be updated during subsequent uploads with the "Upload: Only Modified Files" option set.
If you alter what's on your hosting using an FTP program and then upload from Muse with the Upload: Only Modified Files option set you're likely to end up with a mis-matched or incomplete set of files on your server. -
I can not access my router with Firefox, but IE works fine. Why?
It worked fine until today then I received a message that Internet Explorer will not let Firfox access the Internet.
You can check the exceptions in Tools > Options > Privacy > Cookies: "Exceptions" to see if you have blocked cookies for live.com
You can inspect the permissions (exceptions) for the currently displayed website in "Tools > Page Info > Permissions".<br />
You can inspect the cookies for the currently displayed website in "Tools > Page Info > Security > View Cookies". -
[SOLVED] Failure when loading modules, but everything works fine
I've updated Linux from 2.6 to 3.0, everything seems to be working as before, but I'm getting this when booting:
Loading modules [FAIL]
I don't see anything relevant in dmesg output, everything seems to be loaded fine. Is anybody else getting the same error since the kernel update?
Last edited by Camus (2011-08-08 14:07:56)What's strange is that Tp smapi's functionality seems to be there anyway... It's a module for battery control in Thinkpads and my battery indeed doesn't charge beyond 80%, the way I want it to be.
I'm having the same issue. I think you will find that the "functionality" isn't provided, as you said, /sys/devices/platform/smapi doesn't exist, and that your battery is actually remembering the last charge limits you sent to it. Try to remove the battery and put it back, I'm nearly sure that it'll lose them. This is what happens to me on my second battery, the ultra-bay one, which I occasionally have to remove to insert my CD drive.
No idea why tp_smapi doesn't load when put in MODULES in rc.conf, but workarounds should be easy. Alternatively, if you only use it to update your charge settings, you can just manually load it each time you need to.
EDIT :
Have just found out that by manually adding thinkpad_ec before tp_smapi in MODULES in rc.conf, everything loads. Strange, since thinkpad_ec should be loaded automatically with tp_smapi. But hey, it works.
Last edited by idx (2011-08-19 11:08:08) -
Home router can't connect to third party mail server (internet works fine)
I use speakeasy webmail (MegaPath) and whenever I use my home router (netgear WNR1000) the internet works fine but I can't recieve or send mail either through Apple Mail or through Entourage. When I'm at work, coffee shops or literally any other network my mail works fine. What's going on?
prkswllflwr, Welcome to the discussion area!
Assuming that your sister's Mac has an AirPort Extreme card installed, use the photos in KB 108039, Properly attaching the antenna on an AirPort Extreme Card to verify that the antenna wire is properly connected. -
Got a new motherboard after my PC crashed, because my old one was defect. Now my Creative Suite thinks it's a new computer. I can't register my serial number, because it can't connect to the internet, but internet works fine. What do I do? My operating system is windows 7, System is Intel Core i7-4790 / 16 GB RAM
Contact support by web chat to reset activations and refer to this:
Sign in, activation, or connection errors | CC, CS6, CS5.5
Mylenium -
NAT error: UDP OK but TCP = no route to host
I recently did a firmware update on my Airport Express and I think something has changed which is affecting file transfer speed. A NAT test shows UDP listen port 6881 is OK but when testing TCP listen port 6881 I get the following message:
NAT error: No route to host (173.19.148.196:6881)
I have Mediacom Cable and their provided modem is Touchstone Telephony Modem and my Airport Express is plugged into it to provide me a wireless connection (it has an IP address of 10.0.1.1).
I have a MacBook 4,1 Intel Core 2 Duo and run OS X v. 10.5.6. In Security settings my Firewall is OFF.
Can someone explain to me what I need to do to open the TCP port? Also, what is a UDP connection?
Thank youi had the same problem.
and i did the following steps
on vuze program
1) vuze -> preferences -> incoming tcp listen port (example 50123)
2) set the same port on UDP
after that you have to open tcp protocol (NAT -> virtual server) ... on your router and set start port as the same port as you already set in vuze (ex. 50123)... and an end port (ex. 50124)
be careful as local ip address, you have to set the same ip in the tcp protocol settings with the ip that your macbook uses to connect to the internet. you can find the ip on system preferences --> web--> and get the information.
I hope to help you and others with the same problem! -
My MacBook Pro won't connect to the Internet via wifi but it worked fine on ethernet cord...I tried running diagnostic but it didn't work:(((( it happen every time if I restart the modem and/or router.. Any idea how to fix this?
Hello Rattisate,
Sorry to hear you are not able to connect to Wi-Fi on your MacBook Pro. I would be concerned about this too. You can find information on how to troubleshoot this in the following article:
Troubleshooting Wi-Fi issues in OS X Lion and Mac OS X v10.6
http://support.apple.com/kb/HT4628
Follow the steps in the section labeled, "Symptom: My Mac does not connect to the Internet."
Thank you for posting in the Apple Support Communities.
Best,
Sheila M.
Maybe you are looking for
-
My MacBook is a 2009 working on Mac OS X 10.5.8
and I can't seem to install the latest version of iTunes 11 without OS X 10.6.8 (Lion?) or later... Do I have to buy a new computer? I don't want to pay for software if it's not compatible. Help!
-
Hi, i've some problem with the file rt.jar! when i launch java: Error: failed /usr/local/sun/j2sdk1.4.0_03/jre/lib/i386/client/libjvm.so, because libstdc++-libc6.1-1.so.2:cannot open shared object file: No such file or directory i've installed libstd
-
anybody please provide me the usage tracking document?(what is thee usage of usage tracking and how to implement the usage tracking)
-
Can I use my iPod Touch car charger on my iPad 2?
I have an iPod Touch and have a car charger for it. I just purchased a new iPad 2, and want to know if I can use the same car charger for it? If not, what technical specs should I look for when buying a new charger?
-
I can't download Elements 13. It said an error occurred. I downloaded a trial of Lightroom and it worked. However, when I bought Lightroom, it doesn't download.