Time Capsule wireless network and Windows Vista

I am trying to set up TC on my IMAC.
The set up went fine, but now I'm trying
to add a wireless client. The client would
be windows with vista. Airport utility has
been installed on windows vista. When I try
to connect it sees the new network I set up,
but won't connect to the internet.

Welcome to the discussions!
"When I try
to connect it sees the new network I set up,
but won't connect to the internet."
Are you saying that the Vista PC will connect to the wireless network, but can't get an internet connection, or it can see the wireless network, but can't connect?
If it cannot connect to the wireless network, is there an error message displayed? If so, what does the message say?

Similar Messages

  • I have a 2TB Time Capsule I want a windows vista workstation to be able copy 2 it.

    I have a 2 TB time capsule, I want a windows vista machine to be able to copy files to it. Different people gave me diferent pieces of advice,  some say partitition the time capsule, others say enable SMB on the vista machine.  Since I am not well versed with Time Capsule.  I need someone knowledge to be transferred via this medium so that I can configure my home environment to acheive what is stated in this email.  The way I am configured is The time capsule is also the router, there is one macbook connected to the router and on vista machine connected.   I have not partitioned the time capsule at all.  I am sure there is this type of configuration out there,  Some readers from this forum must know how to do this.  I would like to achieve this without partitioning the time capsule.  Is SMB a good way?  Thank you

    1. Can you ping the IP? If not make sure you are on the same ip subnet.
    Turn off the firewalls, and ensure vista is set to home for network, not work or public.
    2. Once you can ping the TC, try again to get access from Windows Explorer.
    If it fails, ensure the disk share in the TC is set to WORKGROUP or whatever is the correct workgroup for the vista machine.
    Also ensure the guest access is turned on and you have read and write permissions.
    This will work.. you just have to make it.

  • My MBP doesn't remember my Time Capsule wireless network when waking from sleep

    My MBP (OS 10.5.8) doesn't remember my Time Capsule wireless network when waking from sleep.  Thus, every time my MBP wakes from sleep, I need to select the Airport icon in the upper menu bar, select "Join other network", enter SSID and password.  This is very cumbersome.  And, I never had this problem when I was using the ISP's provided wireless router/gateway/DSL modem. Adding the Time Capsule and using it to generate the wireless network has introduced this problem. 
    It appears that this problem has to do with the hidden SSID.  I don't need the lecture on how hidden SSID provides no serious security benefit.  That's why I have the WPA2 encryption.  I'm interested in a solution that will allow the Time Capsule to generate the wireless network, maintain a hidden SSID, continue to use WPA2 encryption, but have my MBP recognzie and autoconnect to this network.
    Solutions I've alread tried:
    1. Open Network Preferences
    2. Select Airport from left hand column (and ensure Airport is at top of that list)
    3.  Select Advanced
    4.  Delete all Preferred Networks.
    5.  Apply settings.
    6.  Restart computer
    7.  Return to Network Preferences and from Advanced page, manually add my network with hidden SSID and WPA2 password
    This solution works fine as long as I don't take my computer elsewhere and connect to another network.  As soon as my preferred networks list gets another network, my MBP stops finding my TC network.  Since I take my laptop to a lot of places (it's a laptop, after all...) this is a problem.
    As I say, prior to adding the TC on my network (and using it to generate the wireless network), my MBP had no problem keeping 50+ preferred network names/passwords in the Preferred Network list, but always automatically finding/connecting to my home network without the need to "Join other network."  Thus, I assume the problem lies with the Time Capsule.
    Any ideas?

    LaPastenague, thanks for weighing in.  Didn't know that the hidden SSID capability was not IEEE standardized, and thus different devices will handle hidden SSID differently.  With my admittedly limited knowledge of how SSID/hidden SSID works, I'm still a little confused as to why my MBP would remember the generic router/gateway's hidden network, but struggle with the TC's hidden network.
    To my knowledge, when an SSID is broadcast by a base station (Airport, wireless gateway, etc.), a connecting device (like a laptop, iPad, etc.) detects this broadcast--this would be a passive reception of this SSID signal.
    When an SSID is hidden, the base station does not broadcast its identification.  Rather, a connecting device must transmit the name, and when the base station recognizes the broadcast, the connection is made. That's what you do when you select "Join another network" and manually enter the SSID.
    The idea with OS X's Network Preferences is that these steps, whether for hidden networks or broadcast SSIDs, become automated.
    Where is the potential for a different chipset between the TC and the previously used wireless router/gateway to alter this functionality?  Shouldn't the selection of an SSID by the MBP to broadcast to seek for a base station be a function solely on the MBP?  And once broadcast by the MBP, the TC should detect and reply? 
    Basically, the MBP can connect to the hidden TC manually just fine.  The MBP can connect to the old setup automatically just fine.  The MBP cannot connect to the TC automatically.  Aren't these automatic connection functions solely on the MBP?
    I'll try un-hiding the network and re-verifying that the problem is exclusively with the hidden network.
    Z

  • How to integrate AT&T U-Verse with existing Time Capsule wireless network

    I would like to switch from Comcast HDTV+Earthlink internet service to AT&T U-Verse, but it’s not clear to me how to integrate the AT&T system with our existing Time Capsule/wireless set-up. The TV (with cabled DVR) is in our family room; the Time Capsule, printer & iMac are in the study. Do I need to move the Time Capsule - so it is directly connected to the AT&T ‘gateway’ box via ethernet cable - or - can I just attach an Airport Express module to the modem/router box and leave the Time Capsule where it is? (I plan to turn off the wireless function on the AT&T device.)

    No, we have a mix of 802.11g & 802.11n devises, so it looks like I will need to use the WDS option
    Yes, this is your only option here.
    can I 'create' a (Apple) WDS network rather than 'participate' in a (2Wire) network?
    Maybe I am mistaken, but I sense that you may be thinking that you can somehow combine the 2 Wire and Apple networks together in a WDS setup. This is not possible since they are not compatible for this purpose.
    You will configure the main Apple router to "participate in a WDS network". There is no other way to set it up if you want to use WDS. It will be configured as the "main base station" in the setup.
    You could leave the 2Wire network "as is" and use it for guests or some other purpose. There is some concern though about having different networks in close proximity due to likely interference effects between the devices.
    (2) Can I use an Airport Express device in 'relay' mode and also use it to stream AirTunes to the stereo?
    Yes
    I'm also wondering if the 2Wire device & the TC should have the same password and security (WPA2), so the NetQuakes seismograph in the garage can 'see' the internet through both devices. But perhaps a question for another day...
    OK to use the same WPA2 Security, but having the same password for two distinct networks may cause some confusion.

  • Extending Gen 1 Time Capsule Wireless network with Airport Express N

    I am having difficulty setting up my new Airport Express w/ 802.11N (SKU# MB321LL/A) to extend the wireless network from my Time Capsule (SKU# MB276LL/A).
    My setup is as follows:
    Time Capsule is connected to Cable modem with the following wireless settings:
    Wireless mode -> Create a Wireless Network
    Allow this network to be extended -> Checked
    Radio Mode ->802.11n (5Ghz N only)
    Wireless Security -> WPA2 Personal
    The issue is the when I attempt to setup the AE to extend the network. I match the settings to the Time Capsule:
    Wireless Mode -> Extend a Network
    Select the Time Capsule Network
    Allow wireless clients -> Checked
    Wireless Security -> WPA2 Personal
    However after I reset the AE the LED glows Amber and the following problem is reported:
    +Wireless Network+
    +This AirPort wireless device is set up to join a specific wireless network that can't be found. If you don't see the network that you want to join in the Network Name Pop-up menu, enter the network name and network password if necessary to try again.+
    When I check the Airport->Wireless tab the settings were as before.
    Any thoughts on this? Thanks.

    Welcome to the discussions!
    Have you tried to position the AirPort Express close, say 10-15 feet, as a test to see if it will connect that way?
    If so, then move it back another 10-15 feet, etc.
    5 GHz signals do not travel well or penetrate surfaces very well, so my first thought was that the signal was not strong enough for the Express to pick it up where you had it located.
    Message was edited by: Bob Timmons

  • My PC (Windows) can't see my Time Capsule wireless Network

    I just installed a wireless network with a Time Capsule and it's working fine for the three Macs and the printer in the household.  However, I still need to have access to the wireless network for one PC running Windows.  Problem is the PC doesn't "see" the Time Capsule Network.  What am I missing and how can I set up the PC on the wireless network?

    Try downloading AirPort Utility for Windows here:
    http://support.apple.com/kb/DL1391

  • Problem with Time Capsule Wireless Network...

    I have Time Capsule over a year and it worked fine with Xfinity Modem. Recently, Xfinity had upgraded modems to Wireless router and I have ARRIS TG862 from them. I was able to set up wireless network using bridge mode on my Time Capsule and it all worked fine for a while.
    My set up is: Arris Router is conected to Time Capsule thru ethernet connection. I have two more Airport Express in different areas of the house (one in Theater room and one in upstair office). I have conncted one port of Time Capsule to linksys switch which is supplying connection for all wired devices on network.
    Last week, our wirless network stopped working and I rebooted router and TC. Still no resolution. I went ahead and set up the TC to factory settings but forgot to plug out all the network connections from it. I reconfiugred Apple TC with same wireless network name and same network settings. Most of the wired devices are connecting fine and two of the iphones and Macbook Pro won't connect. iphones, seems to be getting IP address but won't connect to interent. My windows laptop says connected to "EAGLE" my wireless network but "EAGLE 2" provides internet connection. I have reset my TC to factory defaults and reset same way so many times but still same results. I called Comcast and asked them to turn off wireless in their router thinking that router is creating a second wireless network but I still have the same issue.
    Any suggestions on how should I set up my TC? I think, it went insane..............:(
    Should I set up TC with a brand New wireless network Name to resolve this issue?
    I have 7.6.4 version on TC.
    I thought I knew, but what's the right procedure to set up TC? Plugged in the router and unplug from everything else and connected thru an ethernet connection to my laptop?
    I have wasted so much time on this with the same results every time.
    I did unplug all the network connections from TC and reset to factory defualts and set up my wireless again but same results.
    Can someone please help me with this? Thanks in advance.

    What is the model of the TC? The actual number.. A1xxx from the base of the TC is important.
    When you have a modem router.. then the TC must be in bridge mode.. and create a wireless network.
    Your names are not yet windows compatible.. please use all names that are short, no spaces and pure alphanumeric.
    Fixing names is important part of this.
    But the latest firmware 7.6.4 is also troublesome. I would downgrade it to 7.6.1 and factory reset before you start that process.
    Any TC older than 3years may have hardware issues.. a Gen3, A1355 may need a replacement and certainly anything older does.
    Drivers in windows for wireless are problematic as well..
    Certainly start there and see how it goes.

  • Help with Time Capsule/wireless network setup

    Just purchased Time Capsule, hooked it up, and followed the instructions to create a new wireless network. The problem is that my MacBook Pro can't find the internet via the new Time Capsule network. It can "see" the Time Capsule, and I can log on with the new password, but there is no internet connectivity. If I unhook the ethernet cable from the Time Capsule and hook it directly into the computer, the computer is able to rapidly access the internet. Plug the ethernet back into the Time Capsule, and even though the Time Capsule light is green, there is no internet connectivity for that computer or other computers. Also, the Time Capsule signal strength is exceedingly low. Help!

    Please try the steps again. However, this time, I would like for you to perform a modem reset between powering all the equipment down and starting to power them back up again.
    You should find a reset button on the back of your Motorola modem.
    So, the steps should now be:
    o Power-down all of the equipment, except the modem.
    o Perform the modem reset. Note, the reset may take anywhere from 5 to 30 minutes to complete. Check your User's Guide that came with the modem. If you don't have a copy of the guide, you can get it here: SB5101 User Guide
    o Once the reset is complete, power-up the TC by following the sequence I provided earlier.

  • Can't see wireless network with Windows Vista

    I have the Airport Extreme N and two PCs, one with W XP and one with W Vista. Everything works fine with the XP PC. On the Vista PC, I can connect to the network with LAN, but I can’t see the wireless network.
    The W Vista PC can identify other networks around the block, so the Broadcom 802.11g network adapter seems to work fine. The wireless runs on channel 13, which is OK for the XP PC. I have installed the latest update for the Airport Extreme.
    Any suggestions to what I can do to get the W Vista PC working on wireless?
    Best, Kasper

    Hi,
    I also have the same problem.
    My belkin wirelss router is set to channel 13, therefore my macbook cannot see this network when it search's, for the above reasons.
    However unlike the situation above I am unable to change from channel 13 as we have discovered in the past that this is the only channel that is not in use by other networks around our area. The rest gave us interferance troubles.
    I have a number of windows laptops in the house and there is a setting that you can change so the laptop will search for channel 13. I was wondering if anyone is aware of a setting on the macbook that will make the airport card search for 1 - 13 not just channels 1 - 10 as it is now.
    I thought I would add this question to this topic as it is very similar. I hope I was correct in doing so.
    Thanks,
    Josh
    Macbook   Mac OS X (10.4.8)  

  • External Hard disk connected to time capsule not visible in windows vista

    I have connected my external hard disk to Time capsule. Am Able to find the same in my MBP in finder under shared. But with windows I am not able to see this hard disk. I have installed airport utility and am able to see the time capsule. What to do?

    What is the format on the external USB drive?
    Have you setup the disk in workgroup correctly to the network workgroup name?
    Turn on guest read and write at least to get things started. If you turn on password or changed the default password you will need to remember that.
    How are you trying to access the disk? It will more than likely not show up in network shares, without deliberately using the tc ip.. so open explorer and type in \\YOUR_TC_IP_ADDRESS\Share_name
    If you have installed the airport utility for windows it should also install the required files to find the disk.

  • Extend Time Capsule Wireless Network with Airport Extreme

    I tried to install two base stations in my house. The first one is the Time Capsule which I use as my main router connected to the DSL modem by Ethernet and which has the main wireless network. The second is an Airport Extreme Base Station which tries to connect wirelessly to Time Capsule to extend the wireless network. I use WPA2 Personal as a security mode and it says there is an error at the end when it reconfigures the Airport Base Station --- questions: does it normally work with these two devices in that order? What process to make it work?”

    use Airport Utility manual set up button and place the secondary router in bridge mode then configure your wireless setting.

  • Extending Time Capsule wireless network with an Airport Extreme

    Hello - can anyone please advise about extending a wireless Time Capsule network by adding an Airport Extreme?
    I've looked at the Apple support advice - http://support.apple.com/kb/HT4259?viewlocale=en_US&locale=en_US -
    Wi-Fi base stations: Setting up and configuring an extended wireless network (802.11n) -
    but I couldn't seem to make it work. I don't know if it is different as I'm using Mountain Lion, but I cannot seem to locate a '

    Temporarily, move the AirPort Extreme to the same room or general area of the Time Capsule, power it up, and wait a full minute.
    Then, hold in the reset button on the back of the AirPort Extreme for 9-10 seconds, then release. Allow a full minute for the AirPort Extreme to restart to a slow, blinking amber light.
    Close AirPort Utility if it is open.
    Click the fan shaped AirPort icon at the top of your Mac's screen. Wait a few seconds for the listing of New AirPort Base Station to appear.
    Click on AirPort Extreme just below that and AirPort Utility will open automatically open and analyze your network settings. In the example above, this is shown as an AirPort Express. In another minute, you will see that it will configure the AirPort Extreme to "Extend" the network.
    Enter a device name that you want to use and click Next
    Wait another minute for AirPort Utility to configure the AirPort Extreme. When you see the message of Setup Complete, click Done.
    Move the AirPort Extreme to a location that is approximtely half the distance from the Time Capsule to the area that needs more wireless coverage and power it up.
    You are all set.

  • Time Capsule wireless network not visible.

    I have a first gen TC which up to today was working great.
    Today it was very, very slow on the wireless side but ok on the wired side.
    I restarted the cable modem and the TC, after which everything looks okay - but the wireless network is not visible to any of my devices.
    I have restarted it three times, reset it to factory and reconfigured it, switched the network settings to no security and other things but my iPhone, my iPad and my MacbookPro do not see the wireless network regardless of the security option or the networking type - N-only or B/G compatible.
    As I say it was fine until I returned from vacation today.
    Any thoughts?

    OK, so I have done this and it's made no difference. The new network Apple Network b73829 is still present alongside Wireless LAN.
    I can only access Time Capsule if I switch to the new network, with the resulting loss of internet access from my Powerbook and, if I switch back to Wireless LAN I regain internet access but cannot see Time Capsule.
    Although I just want to use Time Capsule to back up I have tried to connect it to my wireless LAN using the Join Existing Network on Airport Utility (even though I've been told I don't need to do this for Time Machine) but it has failed each time. After entering the password and wireless password information etc. and pressing update the Time Capsule device does re-start but there is ALWAYS an error message that says the device cannot be found and I should check that I am close to it (it's 3 feet away) or I should connect via Ethernet. If I connect via Ethernet it seems to disable the wireless functionality that I bought the device for.

  • Having trouble securing my Time Capsule wireless network

    Hi everyone,
    I purchased the Time Capsule to use as my main source of wireless connection in my living room some few months back. Recently, I have noticed that my wireless network has been acting slower than usual, especially during peak hours. Popping open up system preferences showed me that my Apple wireless network was unsecured.
    Several attempts of changing the WEP password and locking it proved unsuccessful, as I was able to detect the network on my mobile phone and on several laptops I have at home. Changing it to WPA and WPA2 also didn't fix this problem.
    I just wanted to quickly ask if I am doing something wrong? Why am I still able to see my own wireless connection even if I am not using my own computer? (I tested the connectivity by using a seperate laptop I have and I STILL found the network as being unsecured on this laptop and both on my mobile).
    Any help would be greatly appreciated!

    Why am I still able to see my own wireless connection even if I am not using my own computer?
    By default, all wireless routers will broadcast their Network Names (SSID). However, in order to connect to ones that are secured, you would either have to enter the encryption key manually or it can be done automatically if stored in your Mac's Keychain.

  • Time Capsule Wireless Networking

    Hi all,
    I am very new to apple discussion...
    I have a question regarding my time capsule.
    I have set up the tc and it works perfectly... I have closed the wireless network so it is not viewed when someone searches for wireless networks...( to add security)
    The issue is that each time my computer goes on sleep or turn off, when i turn it on, I would have to type the network name and a long password manually and sometimes it gets a bit annoying as you can imagine...
    is there a way that i can save the wireless network on my computer so i don't have to entre the information each time? I have turned " Remember this network " on...
    Also what is the MAC address? i have heard that it can be assigned to the network so the network only allows certain computers to be connected to it, is that right?
    thanks for your help...

    Ehsan Varavipour wrote:
    I have set up the tc and it works perfectly... I have closed the wireless network so it is not viewed when someone searches for wireless networks...( to add security)
    you TC still broadcasts its SSID. there is no "security" advantage in haveing a closed (hidden) network.
    The issue is that each time my computer goes on sleep or turn off, when i turn it on, I would have to type the network name and a long password manually and sometimes it gets a bit annoying as you can imagine...
    yeah, that's why i stopped employing a closed network
    is there a way that i can save the wireless network on my computer so i don't have to entre the information each time? I have turned " Remember this network " on...
    you should be able to accomplish that via keychain. look for a little box to tick where it says "remember this password in my keychain"
    Also what is the MAC address?
    http://en.wikipedia.org/wiki/MAC_address

Maybe you are looking for

  • Creating link on report elements to get more info

    Hello, I have created a data model in BI publisher which integrates two data models one from BI Answser (a query ) and One from source data (a table) I have linked an element on the BI Answer data model to the corresponding lement in the source table

  • Install Device Driver Software for Palm TX

    My new notebook has Windows Vista and I have had my Palm TX for almost two years.  To install the Palm on my notebook I downloaded the version for Vista from Palm.com.  When I went to synchronize the Palm with the computer during the installation the

  • Issue with the last column stretching in ADF table

    There is an issue wherein when  I try stretching the last column of the ADF table to reduce its width it does stretch. But whenever I try stretching it back to this original position it doesn't despite having columnstretching attribute set to multipl

  • Cannot re-install or uninstall itunes

    had a hard drive problem, new one installed, everything working except itunes. my library is intact, but itunes won't open. get error message "Problem with Shortcut - This action is only valid for products that are currently installed". This is after

  • Why is the OTN forum so unstable ?????

    Why is the OTN forum so unstable ????? I haven't seen any other Forum on the WORLD WIDE WEB being so slow/unstable? Maybe you should move over to some MS products (FYI this was a jocke).