To access Web Interface Database

Can anyone help in accessing the database (online peoples IDs) of Yahoo chat rooms (any room e.g. regional, age, romance) and can take their Index or so.

You have to implement the following:
Not sure what you want.
If you need to connect....
Figure out the url you need to connect. Do a http connection and send the url. You will get a html back. Almost any java tutorial will explain how to do this.
If you need 'ids'....
Open a http connection to yahoo. Post the appropiate URLs to get the pages you need. Those will return html pages which you need to parse (search in the swing libraries for a html parser.) Get the text that you are looking for.
If you need to interact....
This is just a different type of 'url' which is defined via CGI. You construct a CGI post/get and send it. You get html back. Parse it and figure, based on the result create some conditional rules to create another CGI post/get and send it off again.

Similar Messages

Can only telnet from other switches to a SG300 switch. Also can't access web interface.

For whatever reason I can telnet from another switch to the SG300 switch but not directly to the switch. I also can't access the web interface or ping the switch. Any help would be appreciated. Here is the running config
config-file-header
WasteWaterSG30010MPP
v1.3.5.58 / R750_NIK_1_35_647_358
CLI v1.0
set system mode switch
file SSD indicator encrypted
ssd-control-start
ssd config
ssd file passphrase control unrestricted
no ssd file integrity control
ssd-control-end xxxxxxxxxxxxxxxxxxxxxxxx
vlan database
default-vlan vlan 2
exit
vlan database
vlan 2,75,200,999
exit
voice vlan id 200
voice vlan oui-table add ________
voice vlan oui-table add _phone_____________
voice vlan oui-table add ___________________
voice vlan oui-table add ______________
voice vlan oui-table add
voice vlan oui-table add ___________
voice vlan oui-table add ___
voice vlan oui-table add ______________
hostname WasteWaterSG30010MPP
line console
exec-timeout 0
exit
line telnet
password 382fda4a4a26e6637edac0eb8b8ba4581087d32d encrypted
exit
line console
password 382fda4a4a26e6637edac0eb8b8ba4581087d32d encrypted
exit
enable password level 15 encrypted 382fda4a4a26e6637edac0eb8b8ba4581087d32d
username admin password encrypted 382fda4a4a26e6637edac0eb8b8ba4581087d32d privi
lege 15
snmp-server location XXXXXXXX
snmp-server community String1 ro view Default
sntp server 172.16.2.1
ip telnet server
interface vlan 2
ip address 172.16.2.23 255.255.255.0
no ip address dhcp
interface gigabitethernet1
storm-control broadcast enable
storm-control broadcast level 10
storm-control include-multicast
port security max 10
port security mode max-addresses
port security discard trap 60
spanning-tree portfast
switchport mode access
switchport access vlan 999
macro description ip_phone_desktop
!next command is internal.
macro auto smartport dynamic_type unknown
interface gigabitethernet2
spanning-tree portfast
switchport mode access
switchport access vlan 999
interface gigabitethernet3
spanning-tree portfast
switchport mode access
switchport access vlan 999
interface gigabitethernet4
storm-control broadcast enable
storm-control broadcast level 10
storm-control include-multicast
port security max 10
port security mode max-addresses
port security discard trap 60
spanning-tree portfast
switchport mode access
switchport access vlan 999
macro description ip_phone_desktop
!next command is internal.
macro auto smartport dynamic_type unknown
interface gigabitethernet5
spanning-tree portfast
switchport mode access
switchport access vlan 999
interface gigabitethernet6
spanning-tree portfast
switchport mode access
interface gigabitethernet7
spanning-tree portfast
switchport mode access
switchport access vlan 999
interface gigabitethernet8
spanning-tree portfast
switchport mode access
switchport access vlan 999
interface gigabitethernet9
spanning-tree link-type point-to-point
switchport trunk allowed vlan add 75,200,999
switchport trunk native vlan 2
macro description switch
!next command is internal.
macro auto smartport dynamic_type switch
interface gigabitethernet10
spanning-tree link-type point-to-point
switchport trunk allowed vlan add 75,200,999
switchport trunk native vlan 2
macro description switch
!next command is internal.
macro auto smartport dynamic_type switch
exit

A member of which VLAN ID is that device from which you trying to reach that switch?
Is that device directly connected to switch WasteWaterSG30010MPP? If yes, to which port?
If you are connecting from different VLAN than VLAN2, are you using routing between VLANs? Where is that routing device connected to?
> I also have another switch that connects to the network through this switch and am able to telnet to it.
that second switch member of same VLAN 2? Or management is part of different VLAN?
..too few information to be able to give you final answer.

Cisco RM-1252G-A-K9 can't access web interface

I hope I am in the correct forum for this topic?
For some reason I cannot access the web interface in order to configure this device. I have it connected to a router (DHCP). The router assigns an IP Address and I can ping it. If I attempt to go to that IP Address in any web browser. the page cannot be displayed. I've reset it several times. I have 2 of these and same problem. Am I missing something obvious? I sure hope so...

Connecting to the Access Point Locally
If you need to configure the access point locally (without connecting it to a wired LAN), you can connect a PC to its console port by using a DB-9 to RJ-45 serial cable.
Follow these steps to open the CLI by connecting to the access point console port.
Step 1 Connect a nine-pin, female DB-9 to RJ-45 serial cable to the RJ-45 console port on the access point and to the COM port on the PC.
Step 2 Set up a terminal emulator on your PC to communicate with the access point. Use the following settings for the terminal emulator connection: 9600 baud, 8 data bits, no parity, 1 stop bit, and no flow control.
Assigning an IP Address Using the CLI
When you assign an IP address to the access point using the CLI, you must assign the address to the BVI. Beginning in a privileged EXEC mode, follow these steps to assign an IP address to the access point BVI using the console port:
Command
Purpose
Step 1
enable
Enter privileged EXEC mode.
Step 2
configure terminal
Enter global configuration mode.
Step 3
Interface bvi1
Enters interface configuration mode for the BVI.
Step 4
ip address address mask
Assigns an IP address and subnet mask address to the BVI.
Step 5
end
Return to privileged EXEC mode.

Can not access web interface: Linux: permission denied

When starting my oracle-xe on centos5 it works but i can not open the web interface. During install i have configured it on port 81 and this is the error i get when starting the db:
30-MAY-2010 19:17:54 * (CONNECT_DATA=(CID=(PROGRAM=)(HOST=localhost.localdomain)(USER=oracle))(COMMAND=status)(ARGUMENTS=64)(SERVICE=LISTENER)(VERSION=169869568)) * status * 0
Error listening on: (Description=(Address=(Protocol=tcp)(Port=81)(Host=localhost))(Presentation=HTTP)(Session=RAW))
30-MAY-2010 19:17:57 * service_update * XE * 12546
TNS-12546: TNS:permission denied
TNS-12560: TNS:protocol adapter error
TNS-00516: Permission denied
Linux Error: 13: Permission deniedFirewall and seLinux are disbled.
I have installed oracle-xe as root and added root to the dba-group
What could be the issue for this?
Edited by: Yannick.O on May 30, 2010 10:35 AM

You have to use some port higher then 1024. Ports below 1024 are reserved for root user only.

HP LaserJet 400 MFP M425dn: bug in MTU path discovery, printer reboots via web interface

Firmware Datecode: 20121205
1. We can not access this MFU over VPN link. Otherer devices are accessed successfully.
As far as I understand there is an error in MTU Path Discovery.
tcpdump logs are attached.
Is there a way to change MTU of this device?
2. This MFU a reboots when I open page "Settings" of "Networking" submenu (/hp/device/set_config_networkSettings.html?tab=Networking&menu=NetSettings) if option "System" -> "System Setup" -> "Language" is "Russian". But this looks like a very good feature since I've have not found the way to reboot this printer remotely.
Here I was tring to access web interface over VPN (IPSec), 192.168.4.135 is IP of my comp, 192.168.160.200 - is IP of MFU, 192.168.160.254 is a gateway:
$ tcpdump -n -r printer-1.pcap
reading from file printer-1.pcap, link-type EN10MB (Ethernet)
17:20:29.337867 IP 192.168.4.135.54147 > 192.168.160.200.80: Flags [S], seq 2356029847, win 8192, options [mss 1460,nop,nop,sackOK], length 0
17:20:29.338026 IP 192.168.160.200.80 > 192.168.4.135.54147: Flags [S.], seq 614551948, ack 2356029848, win 8760, options [mss 1460,nop,nop,sackOK], length 0
17:20:29.344909 IP 192.168.4.135.54147 > 192.168.160.200.80: Flags [.], ack 1, win 64240, length 0
17:20:29.348488 IP 192.168.4.135.54147 > 192.168.160.200.80: Flags [P.], seq 1:304, ack 1, win 64240, length 303
17:20:29.348564 IP 192.168.160.200.80 > 192.168.4.135.54147: Flags [.], ack 304, win 8457, length 0
17:20:29.378872 IP 192.168.160.200.80 > 192.168.4.135.54147: Flags [P.], seq 1:513, ack 304, win 8457, length 512
17:20:29.379063 IP 192.168.160.200.80 > 192.168.4.135.54147: Flags [.], seq 513:1973, ack 304, win 8457, length 1460
17:20:29.379100 IP 192.168.160.254 > 192.168.160.200: ICMP 192.168.4.135 unreachable - need to frag (mtu 1280), length 48
17:20:29.379103 IP 192.168.160.200.80 > 192.168.4.135.54147: Flags [.], seq 1973:3433, ack 304, win 8457, length 1460
17:20:29.379135 IP 192.168.160.254 > 192.168.160.200: ICMP 192.168.4.135 unreachable - need to frag (mtu 1280), length 48
17:20:29.379251 IP 192.168.160.200.80 > 192.168.4.135.54147: Flags [.], seq 1:1461, ack 304, win 8457, length 1460
17:20:29.379272 IP 192.168.160.254 > 192.168.160.200: ICMP 192.168.4.135 unreachable - need to frag (mtu 1280), length 48
17:20:29.379274 IP 192.168.160.200.80 > 192.168.4.135.54147: Flags [.], seq 1461:2921, ack 304, win 8457, length 1460
17:20:29.379304 IP 192.168.160.254 > 192.168.160.200: ICMP 192.168.4.135 unreachable - need to frag (mtu 1280), length 48
17:20:29.379306 IP 192.168.160.200.80 > 192.168.4.135.54147: Flags [.], seq 2921:4381, ack 304, win 8457, length 1460
17:20:29.379335 IP 192.168.160.254 > 192.168.160.200: ICMP 192.168.4.135 unreachable - need to frag (mtu 1280), length 48
17:20:29.379338 IP 192.168.160.200.80 > 192.168.4.135.54147: Flags [.], seq 1:1461, ack 304, win 8457, length 1460
This is more detailed view on some packets.
$ tcpdump -nv -r printer-1.pcap
17:20:29.379063 IP (tos 0x0, ttl 64, id 1, offset 0, flags [DF], proto TCP (6), length 1500)
192.168.160.200.80 > 192.168.4.135.54147: Flags [.], cksum 0x7233 (correct), seq 513:1973, ack 304, win 8457, length 1460
17:20:29.379100 IP (tos 0x0, ttl 64, id 62678, offset 0, flags [DF], proto ICMP (1), length 68)
192.168.160.254 > 192.168.160.200: ICMP 192.168.4.135 unreachable - need to frag (mtu 1280), length 48
IP (tos 0x0, ttl 64, id 1, offset 0, flags [DF], proto TCP (6), length 1500)
192.168.160.200.80 > 192.168.4.135.54147: Flags [.], seq 513:1973, ack 304, win 8457, length 1460
17:20:29.379103 IP (tos 0x0, ttl 64, id 1, offset 0, flags [DF], proto TCP (6), length 1500)
192.168.160.200.80 > 192.168.4.135.54147: Flags [.], cksum 0x5edf (correct), seq 1973:3433, ack 304, win 8457, length 1460
17:20:29.379135 IP (tos 0x0, ttl 64, id 62679, offset 0, flags [DF], proto ICMP (1), length 68)
192.168.160.254 > 192.168.160.200: ICMP 192.168.4.135 unreachable - need to frag (mtu 1280), length 48
IP (tos 0x0, ttl 64, id 1, offset 0, flags [DF], proto TCP (6), length 1500)
192.168.160.200.80 > 192.168.4.135.54147: Flags [.], seq 1973:3433, ack 304, win 8457, length 1460
17:20:29.379251 IP (tos 0x0, ttl 64, id 1, offset 0, flags [DF], proto TCP (6), length 1500)
192.168.160.200.80 > 192.168.4.135.54147: Flags [.], cksum 0x0c1c (correct), seq 1:1461, ack 304, win 8457,
P.S. This thread has been moved from LaserJets to Multifunction and All-in-One - HP Forums Moderator

John Getzke wrote:
Its hard to understand what you are trying to do or ask here. We have some offices connected via IPSEC tunnels. IPSEC interface's MTU is 1280 bytes (not 1500 bytes as Ethernet). All other devices successfully work over this VPN link. HP m2727 works. HP m425dn does not work. As a network administrator I've traced source of problem on all possible points and found that HP m425dn has a bug in the "Path MTU Path discovery" routine. The logs I attached shows that any packet of the TCP stream that the printer (160.200) sends to host (4.135) has "Don't fragment" flag set. According to IP standard the router HAVE TO discard the packet with DF flag set and size bigger then MTU since it can not pass a packet further without fragmentation - IPSEC MTU is 1280 bytes only while HP sends 1500 bytes. The router informs the printer about this problem with ICMP message Type: 3 (Destination unreachable) with Code: 4 (Fragmentation needed) suggesting MTU of next hop: 1280. The router does not communicate with the printer itself, it just informs the printer about network problem. According to IP standard the printer HAVE TO resend this data with the size of packet decreased according to suggested size. This is expected behavior of the Path MTU discovery routine. But the printer sends the packet again with the same size and DF flag set. The router again discards the packet and informs printer... This cycle repeats again and again until connection is closed due to timeout. Therefore "Path MTU discovery" routine is broken at this device. It would not be a serious problem, but the printer resends packets at rate over 28000 pps (about 40 MBytes per seconds) and its CPU is so heavily loaded that it even does not respond to touches on its touchscreen. So an innocent attempt to print document on terminal server located at another office leads to inaccessibility of the printer.
The network dump can be downloaded in PCAP format from here.

[SOLVED]cups web interface bad request error

Installed cups, libcups and all the other pckages mentioned in CUPS archwiki page and also insatlled cups-pdf. Avahi-daemon is enabled and so does cupsd but on accessing web interface at archlinux:631 it give "Bad Request" message. Basically all I need is a virtual pdf printer like cups-pdf and my hp offficejet 5610 printer connected. any help is much appreciated.
Last edited by rsplenum (2013-02-04 20:10:28)

As stated, my home laptop could still access localhost:631 with my ipv6 host line commented out in /etc/hosts. I just updated another post with what I think the problem is, which is a ListenStream=631 line in /usr/lib/systemd/system/cups.socket which did not exist in the 1.7.0 version of cups. The 1.7.1 version was pushed out sometime last month, which might explain these posts only coming up now (there's at least three I've found). Read more via my post in the other thread.
I know this is solved, but wanted to leave breadcrumbs in related threads in case the solution here doesn't work for those who stumble on this.
Last edited by jwhendy (2014-02-09 20:15:08)

FIM Out of the box Reporting - web interface

Hi,
My customer is using standard FIM 2010 R2 reporting. They want to give access to reports to some users without installing SCSM console. Is there any way to give web access (web interface) to these reports?
Borys Majewski, Identity Management Solutions Architect (Blog: IDArchitect.NET)

You could use SQL Server Reporting Services (SSRS). It should already be up and running in their environment as part of the FIM 2010 R2 reporting installation. Security in SSRS can be based on AD group membership.
You might have to look into what the actual SSRS data sources are using for credentials. If they are impersonating the user executing the report, then the user may not have access to the data.
Thanks,
Mark
Mark Creekmore - BlueVault Software http://www.bluevaultsoftware.com

SFE-2010P Crash on web interface access

Hello!
I have 1 SFE-2010P with latest factory installed firmware 2.0.1.80 3/06/2008.
It's configured to be on access mode for a remote branch.
It has a trunk with other Linksys switch, which has a trunk with a core Catalyst switch.
There are several VLAN's on the switch.
Management IP is on VLAN 201,and has ip 192.168.201.42.
Everything works great until I try to get an access to Web Interface of the switch. From different VLAN and subnet (192.168.3.0/24) I'm connecting through
Catalyst 3750 to 192.168.201.42 (a /24 subnet). I log in as valid user (admin), and when the browser points me to http://192.168.201.42/home.htm
switch REBOOTS!!!!
Telnet (Menu and LCLI mode) works great, and doesn't reboot the switch.
SFE-2010 is a great hardware, and it's a most powerful from Linksys's switches.
So I hope you'll help me.
P.S.
Here is my config:
interface ethernet g1
switchport mode trunk
exit
vlan database
vlan 10,30,108,201
exit
interface ethernet e27
switchport access vlan 10
exit
interface ethernet g1
switchport trunk allowed vlan add 10
exit
interface ethernet g1
switchport trunk allowed vlan add 30
exit
interface range ethernet e(1-12,14-26,28-48)
switchport access vlan 108
exit
interface ethernet g1
switchport trunk allowed vlan add 108
exit
interface ethernet e13
switchport access vlan 201
exit
interface ethernet g1
switchport trunk allowed vlan add 201
exit
interface vlan 10
name pp-a
exit
interface vlan 30
name av
exit
interface vlan 108
name veda8_lan
exit
interface vlan 201
name Management
exit
no ip dhcp snooping verify
interface vlan 201
ip address 192.168.201.42 255.255.255.0
exit
ip default-gateway 192.168.201.12

If the management IP of your switch is 192.168.201.42, then it must be in VLAN 108 and not in VLAN 201 but assuming I didn't get it correctly, it seems that you're in the right track because as soon as you're asking to log-in to the admin page of the SFE switch, it means that you're using the correct and management PC of the switch. I would agree with you, you're supposed to access it and it shouldn't behave that way. Maybe you could still narrow down the setup of you network. I mean, maybe you could try changing the management VLAN or use the computer that is directly connected to that switch while accessing it. Thanks!

Problems access to a web application (Web Interface or Web report)

Hi,
We found problems with the access to web application. Some users have problems with direct links to the web applications(Web Interface or Web reporting), when they click on the link an error message appears, the message displays the following text:
"Cannot open file Bex?sap-language=ENbsplanguge=ENcmd=idoc_TE.."
Clicking in details the message is "No Access to specified file"
For this users the access to excel reporting is correct, the message appears when they click on the direct web links through the browser or directly in BW system, but if they type the URL they can access. Other users can use the direct web link without problems.
I highly appreciate any help or idea about how to solve this issue.
Thanks in advance.

HI,
please ask to your basis that check the language of every single user on su01 tx.
This is the problem i think.
Natalia.

Access to MySql Database in the Web Service

Hi all,
In my j2me web service project, i want to access to MySql database in the web service and
my installation is
Tomcat 5.0 for Java WSDP,
Java Web Services Developer Pack 1.5,
MySql Server 5.0 and environment variables are adjusted...
server.xml where is in "C:\tomcat50-jwsdp\conf" is adjusted like this

<Realm className="org.apache.catalina.realm.JDBCRealm"
     debug="99"
     driverName="com.mysql.jdbc.Driver"
     connectionURL="jdbc:mysql://localhost:3306/erendb"
     connectionName="root"
     connectionPassword=""
/>
but i have not access to MySql database in the web service yet...
please help...

Hi Luis,
If you see closely, the productID is actually a concatenation of the areaID and the productID. The reasoning here is that a product can be in multiple nodes of the product catalog and one would need to specify the product on a particular node for the direct URL to work.
On a client site, we came up with a better solution by creating a new FM to retrieve the specific areaID and productID for a product. This FM could be called by extending the webshop. Then a .NET program was written to re-direct a shortened form of the URL to the long URL and therefore the specific product in the product catalog. Eg.: http://yyyyy.com/b2c/b2c/product would be automatically redirected to http://yyyyy.com/b2c/b2c/init.do?shop=<shop name>&areaID=<area Guid>&productID=<product Guid>, something similar to the concept behind "tinyurl.com". A point to remember here is that this would work only for the B2C webshop.
Hope this helps.
Cheers,
Ashok.

Content Library / Web Interface - access issue

BPC Microsoft 7.5 SP6
Windows 2008 R2 server
We have puublished an Excel template as an HTML page to allow (web only users) access to a menuing system and have subsequent access to their individual reports in PDF format. The menu page comes up without errors but I encounter the error "You don't have access" when clicking on a menu option (cells within template). The cells contain an Excel Hyperlink function in conjunction with a EVBNV function to launch this report. (No BPC or excel errors exist within template)
We have created a virtual directory for BPC application in addition to Reports and ReportServer for Reporting Services. We have modified the Site Settings and Folder Setttings in Reporting Services configuration to allow web users to correct role access.Users can access Reporting services Report url without a problem but the web interface does not want to launch/retrieve a pdf file. We have the correct BPC task capabilities and task profiles assigned, insuring they can access and use the content library.
Thoughts?
Thanks in advance.

It appears there is an issue with EVBNV formula and its ability to dynamically pass parameters in HTML format.
IM 0003554460/20111

SRW224G4P: no web interface access

Hi to all!
I've read many ppl having similar problem, but mine is a little bit different.
The web interface of my switch (SRW224G4P) used to work very well, but since some time it is not possible to access, it sends back a page that contains:
<html><body><script>window.close();</script></body></html>
On Safari and IE it closes the window (of course), on Chrome it stays blank.
If I try to access via HTTPS it raises a problem with certificate, saying the certificate is for sw0.ph.cube.lan (the previous name of the siwtch) and not for sw0.voip.cube.lan (the actual name). I suspected it could be something related to name change, but even going back to the previous setting does not resolve.
I've tried to reset to factory defaults, even reflashing with the same firmware version, but the problem is not solved yet.
HW: SRW224G4P
SW: 1.3.1
TIA
Andrea Mistrali

Hi Andrea
You have done everything I would have tried, except have you upgrades your Internet explorer to a very recent Version ?
the datasheet shows that the unit supports only "Microsoft Internet Explorer (version 5.5 or later)" but I am thinking that it works best with IE6.
Maybe someone else has a better idea, but try using a IE version 6 and maybe not the more recent versions of IE.
If that fails, since the product has a "5-year limited hardware warranty with return to factory replacement and 90-day limited software warranty"
If the problem really is switch software on that switch, it sounds like a case for a replacement.
Contact the Small Business Support Center via the following URL.
http://www.cisco.com/en/US/support/tsd_cisco_small_business_support_center_contacts.html
regards Dave

Accessing an SQL Server Database created by MS Access Web App

1.I have tried to use MS Access Web App which has created an SQL Server Database. I would like to access the database using SQL Management Studio Express 2014. In access I can see the server name on windows.net and the database name but I do not know
how to connect to this using SSMS Express 2014. Can you please help?
2.I also want to view our emails on MS Exchange in real-time. In MS Access Jet I can do this by linking the folders as tables. Is there a way of doing this in SQL Server? If not can I have a separate MS Access Jet with linked tables which I can then link into
my SQL Server as an OLEDB Linked server?
3. If going for the Linked Table in Jet solution where can I store it so that my MS Access Web App will have access to it?

Hi gkounis,
I don't think it support link MS Access Jet with linked tables in SQL Server.
Can you share some info about your MS Access Web App?
Regards,
Black

Security when using EM web interface to administer the database

When I'm connecting to the database
via EM Database Control web interface,
it uses http protocol (http://machine:5500/em),
can it be used for safety https protocol,
or are there when using standard http protocol
at least passwords encrypted before
sending it over http?

I have called
'emctl secure dbconsole' command,
it run successfully,
but when I tried to start it
'emctl start dbconsole', it failed,
now I'm not able to stop it,
when I do so, the output is like this
'--- Failed to shutdown DBConsole Gracefully ---',
the state is 'not running', but when I try to
start it now it complains that EM Database Control
is already running.
What to do to make it work now at least without SSL?

Does not open Web interface EM Database Control

Oracle Enterprise Manager 11g Database Control Release 11.2.0.1.0
Agent is running, dbconsole too.
to the database through SQL Developer and SQL Plus connects.
when you go to localhost:1158/em opens a BLANK PAGE that contains 2 "squiggles" view"|[ ]]"
tried in different browsers, identical.
a feeling that most web interface is physically not in folders Oracle or what could be the problem, tell me please?

Oracle Enterprise Manager 11g Database Control Release 11.2.0.1.0
Agent is running, dbconsole too.
to the database through SQL Developer and SQL Plus connects.
when you go to localhost:1158/em opens a BLANK PAGE that contains 2 "squiggles" view"|[ ]]"
tried in different browsers, identical.
a feeling that most web interface is physically not in folders Oracle or what could be the problem, tell me please?

To access Web Interface Database

Similar Messages

Maybe you are looking for