TS5198 Unsupported hardware only mentioned after release?

I'm very upset that these unsupported displays were not mentioned before I upgraded to Mavericks... Now, since I upgraded, my perfectly working, beautiful acrylic Cinema Display (which was totally fine under 10.8) is no longer usable with my system --try using a display in the daytime without being able to turn up the brightness from it's lowest level, it's unusable.
This isn't a CPU or some other internal component that has been slowly getting obsolete after many years of Moore's law at work...this is a display.
Mostly I'm upset that these incompatibilities were not stated outright from the start and now only slyly addressed weeks and weeks later in a support forum.
Any one else having questions as to Apple's response to this issue?
And, has anyone the tech know-how to resolve this issue sans-Apple?
Thanks

Instead of attempting to do it without Apple's help, I suggest bringing it up to AppleCare.     Point them to the article. Get a free online http://developer.apple.com/ account and submit a bug report at http://bugreporter.apple.com/
In the past when Apple has considered hardware obsolete, it was not sold for at least seven years.
http://en.wikipedia.org/wiki/Apple_Cinema_Display Gives you the display history. Now I'm not sure which one yours is, but based on: http://support.apple.com/kb/HT1752 it sounds like they have already considered it obsolete on a certain number of years.    Recover your backup and continue to use 10.8 until you can change to a different display.

Similar Messages

Quartz Complains of Unsupported hardware after 10.5.5 update

I have a Macbook 2.1 (which comes with the onboard intel GMA 950 display card).
Previously all the nice graphic effects like font aliasing, pretty effects while alt-tab, etc used to work by default. Previously I could run many of the .qtz file on my machine, for e.g. "Word of the Day" screen saver. But after the upgrade all these UI pretty candy has diseppeared.
Most irritating is that of text aliasing is not enabled anymore. A bit of investigation indicated that Quartz acceleration has been disabled! On running Quartz composer I see an error that i have an unsupported hardware. Why has the hardware requirements been pushed up when it was not the case before?
How do I enable this again?

That's a really nice list.
Sounds like something is screwing around with memory and that's causing the panic. See what's running. Though modern memory management is much better, there are still problems when programs hold memory, don't release memory, try to claim unavailable memory, etc.

Will it be possible to create new version of document only after releasing

Dear Expert,
is it possible to create a new version of the document only after release of the document...i don't want document version should be created other then release status.
Bhuwan

Hello,
Since you are a technical consultant also, probably you are in a better position to deside how to achieve this.
You will have to develop a user exit which will check status/ Release Indicator of Document when new version option is clicked through CV01N/ 2N/ 3N/ 4N transaction and take necessary action.
Regards,
Milind Dumbre

Entry Sheet Printout only after Release

Hi all,
I wanna know if its possible to configure that an Entry Sheet could only be printed after released?
If so, how could this be made?
Regards.
Gregory.
Edited by: Gregory Mayorga on May 28, 2010 4:21 PM

Hi,
In the IMG ->External services management->Messages->output control for
SES->Define access sequence for SES -> select access sequence 0001->
select (for example) table 506 ->fields
...here you will see that you can add KZABN to communication
structure KOMKBES. If the entry sheet was accepted, KZABN with "A" must be checked. Please create also a condition record accordingly (MN13).
Please check additionally:
spro > material management   > external services Management   >
messages   > define condition table for service entry sheet   > create
condition table
There is on acceptance on the right hand pannel under field
catalog, please make sure you select this field and move them to the
left hand panel
If this is setup correctly , then please check the following:
- the output type use for service entry sheet. If it is NEU (SAP
standard) , check the access sequence assigned
- check the configuration of access sequence, whether this customzied
condition is assigned?
- If it is assign, whether the exclusive flag is setup
if the above customizing is correct, the next step is to check the
output condition record via txn MN15 (to display)
Please also check the flags which you have assigned to your message determination schema in the customizing under "Assign Schema to Service Entry Sheet "
Regards,
Edit

Files hanging in print queue. Reboot seems only way to release to print device

The tech from the Windows Forum suggested I should post my problem here because you folks have better expertise.
My OS is Win 7 Pro. Have three output devices. Two hang files in the print queue. Third is an early 90's vintage HP Laserjet. Works flawless.
All devices are connected to our ehternet and Dell server. Other users do not experience the problem my desktop unit suddenly has encounted.
1. Ricoh Model C5501 with Fiery (Had on the network for two years, no problem until recent.
2. No hardware or softwware changes, although the problem started happening after a late December or Early January Windows update. Only thing I know . Coincidence? Maybe
3. Computer is on a domain network
4. Sometimes I get a message out of the system tray that tells me the document failed to print, but there is no message number. Other devices no message at all.
The files just fail to print or released from the print queue.
I can open the print queue and delete the files or cancel printing without a problem.
Tried stopping and restarting the print spooler. No help. Files still in print queue.
Re-booting the computer will release the files from the print queue. That has been my only dastardly work around.
Could my print spooler files be corrupted? Could a Windows update have changed my environment or written a file to cause this scenario?

Hi Robison,
Could you please tell us what update have you installed recently? since this issue only occurred after installing this update, Maybe something installed in your system conflicts with it, in order to find out whether this is a culprit, I suggest you uninstall
this update for a test.
Plaese also keep the latest drivers for the printers or just reinstall the drivers.
Yolanda
TechNet Community Support

Disabling selected Purchase Order field(s) after released/approved

Hi Experts,
I have a requirement to disable specific Purchase Order fields after released via ME29N.
For example, in Purchase Requisition - I can "Release Indicator - Field Selection Key" to control Purchase Requisition screen layout. However, for Purchase Order - the configuration for "Release Indicator" consist only standard default "Chgable" options.
Question:
Is there a way to customize the Purchase Order "Release Indicator" for screen layout based on customer requirements other that using the default as mentioned above?
Thank you.
Steven

Hi Padmasri,
I understand your explanation on the standard SAP behavior.
Nevertheless, I'm looking for some flexibility to meet customer requirement. Like in Purchase Requisition, there is option to further customize the screen layout by linking it to the "Release Indicator".
Therefore, apart from the standard 6 options given by standard SAP, can we add/customize the options? For example, my customer may one to change a field in the Purchase Order even after released.
Thank you.
Steven

MBP only restarts after rest

Folks,
I'm re-posting this here from another thread in the hope that I'll get a better response. It's a compilation of my observations to date.
Situation:
My MBP has begun to refuse to start on first attempt. This AM it started fine. I then shut it down & tried again a few minutes later. Nothing. Would not restart.
I removed the battery/mag-safe & held the power button down for 5 seconds. I also cleared the PRAM. Yesterday I tried holding the power button down while inserting the power cord. It started. Today I could not replicate this. However, after about 10 tries it finally turned on. Battery is fully charged.
Once booted it runs perfectly. Yesterday, just in case, I made an image of both my Mac & BootCamp partitions. No problem.
This has me stumped. Bad power switch? Loose power switch connection? I'm perfectly willing to fix this myself if somebody can point me in the right direction.
Update:
I went to my local Apple Store & spoke with one of their techs. Very professional.
He suggested I replace the upper case. I can do that.
However, after I came home I had a thought (rare enough), so I tried a little experiment. I discovered that, if I leave the machine off for 18 minutes or more, it starts just fine. Every time.
Could this be a temperature/heat related matter? And, if so, what could the heat be affecting??
Update #2:
I haven't heard a word from anyone as to the possible cause of this phenomenon; except to try installing a new $300 upper case.
I'm becoming concerned that I may have no choice but to ship this rig back to Apple. I'd hate to do that. I don't want to be without it for the weeks it would take to maybe find the problem & maybe fix it. I'll fix it myself, if only I can isolate the culprit.
So, here's what I've done since the last entry:
1.) I timed how long it takes for it to "recover" so that it will power up after being shut down. It was between 18 & 20 minutes.
2.) I ran Tech Tool Pro 4. It passed every test, including memory.
3.) CPU temp at rest is somewhere around low 40's to mid 50's Celsius. That's about 5 degrees higher than my new iMac at work, but this is a Core Duo MBP & they tend to run warm.
4.) I ran Software Update last night. It updated and rebooted fine. But, that didn't involve using the power button.
My next test will be to see if it will do a hard shut down immediately after boot; before the unit has had a chance to get hot. But, hopefully someone will have a suggestion in the meantime.
Update #3:
This AM I pressed the power button & started the boot process. I then, after about 15 second pressed & held the button down to see if it would power down. It did.
I then rebooted & allowed it to fully load. Then, after about 2 minutes, I tried a hard shutdown. No go.
Therefore, it would seem that either heat, or some "full" electrical charge (?) is preventing the power button shutdown or startup after it has been allowed to completely boot.
After about 20 minutes, after the heat or charge has dissipated, it works just fine.
If I have to send this machine to Apple so be it. But, my growing concern is that this problem is so obscure that I might be without my computer for a considerable period of time.
At this point any and all comments are more than welcome. I'm desperate.
Thanks,
Jack

S.U. &/or anyone else,
O.K., I'm back to square one.
History:
1.) I discovered that my MBP would only restart after a rest period of somewhere around 20 minutes. I assumed a heat/power button issue. My local Apple Store tech suggested that upper case needed replacement.
2.) On a whim If discovered that if I pressed the TYGH keys fairly hard the machine would restart immediately, without the waiting period mentioned in #1 above. Since the keyboard cable to logic board connector is right under these keys I assumed that the connector was loose. I ordered some Kapton tape and planned to reseat the keyboard connector and retape it more securely.
3.) While waiting for the tape to arrive I kept using the TYGH key combo if I needed a fast resart. But, after 2-3 days of doing this I noticed that it didn't always immediately work; that I would need to repeat the process. Then after the machine booted I noticed that some keys began to refuse to work. If I pressed randomly around the board eventually they would come to life, but not always stay alive. It seemed to be getting worse, so to prevent further damage I retired the MBP & grabbed my old iBook G3.
4.) The tape arrived. Yesterday I opened the case, examine the keyboard cable plug & logic board socket under a magnifier. Both looked undamaged. I then reseated the connector and taped it down securely. Everything looked perfect.
5.) I reassembled the machine, slowly & carefully. I then pushed the power button. Nothing. So, I tried the TYGH combo. The machine started. But, many keys refused to work.
So, here is where it stands. I'm going to assume that I have a keyboard or keyboard cable malfunction; not a power button problem.
Question: I'll get a keyboard from iFixit & install myself if the general consensus is that the keyboard is the problem. But, does the keyboard come with the cable? I see no reason to replace the upper case, since it doesn't come with the keyboard, only the power button & trackpad. and, that doesn't seem to be the problem.
Any further suggestion in this situation are more than welcome.

MIRO still Payment Block after Release

Dear Experts,
I got a trouble with invoice process. We are using workflow to release payment block, so that the status of the MIRO can be changed from "P Payment Request" to "Free for Payment". The problem is the status cannot be changed to "Free for Payment" even after release via workflow has been carried out. When we checked the workflow status, the workflow runs well, and the release successfully done via that workflow. Another problem is : this case happens only on several MIROs randomly. Sometimes this case happens, while in another MIRO this case never happens.
Can you help me with the problem? Is there any reason why this kind of issue happens?
Thank you very much

hi,
check the below mwntioned link.
Payment Block after MIRO posting
regards
sumit simran

Need to Change PR after Release

Hi,
We have a PR which is created and Released. It is configured in such a way that after release, changes are not allowed. Now, the user wants to change the Purchase Group field (only that field) in the PR without re-triggering the release strategy. I checked the Release Indicator in the Release Strategy and changed the field 'Changeable' to the value 2.
Now, it allows to change the Purchase Group. But, user also be able to add new line items to PR, which we don't want to allow.That means, user should only be able to change the Purchase Group field of the existing line items. No other changes should be allowed.
How we can solve this issue.. Please give me your suggestions.
Thanks in advance.

Hi Arminda,
Thanks for your reply.
I tried that. As you said, it will make all fields as 'Display' and only 'Purchasing Group' as editable.
But, the problem is, it will allow the user to add a new line item to the PR without affecting the Release Status.
I don't want to allow the user to add another line item.
Is there any control in the field 'Changeable' where we give the values 1 to 4 ? Please let me know.

Changes in PR even after release

Dear Gurus
In purchase Requisition change (ME52N) it is allowing to change PR Quantity and Price even after released from the higher authorities.
What Configuration has to be done so that After release of PO system should not allow to do any changes in Purchase requisition.
Where as the purchase requisiotn changes has to be done only after the higher authority asks to make changes i.e the higher authorities has sent for revision.
Also plz let me know how can the higher authority set the purchase req for Changes in SAP (Any configuration has to be done for that).
Or any customizing settings required.
If the Changes is done in PR then again release strategy should be applicable.
Please guide me.
Regards
shailesh

Hi SHailesh,
In your release procedure for PR's. For the release indicator, in the field changebill enter
Options:
1 - Cannot be changed (no changes possible)
4 - Changeable, but new release in case of value change or strategy change
The above will resolve your issue.
if helpful award points
Regards,
Vivek

Why can we only use 1 release class for overall Release of Purchase Req?

Hi,
After realizing that it would be beneficial to use more than one release class for overall release of Purchase Requisition with classification, in use with release groups for overall release, I now ask if someone knows why SAP has chosen to only allow 1 release class for overall release of Purchase Requisition?
In my scenario I would like Release group US, used for release strategies for US-plant to be able to use 1 release class with a specific set of characteristics.
For example class REL_PREQ_CLASS_OVERALL_VALUE_IN_USD including a characteristic PR_TOTVAL_USD looking at CEBAN-GFWRT. The chosen currency for this characteristic would be USD.
I would then like to allow Release group FR, used for release strategies for FRANCE-plant to use another release class with another set of characteristics.
For example class REL_PREQ_CLASS_OVERALL_VALUE_IN_EUR including a characteristic PR_TOTVAL_EUR looking at CEBAN-GFWRT. The chosen currency for this characteristic would be EUR.
In this way the release strategies for the respective release groups US and FR, could maintain their overall limit values in their respective release strategies in their own currencies.
1. Observe that I do not want to use the same Release class for both release groups for overall release, even though I know that this is currently the only allowed option, as far as I've understood.
2. Observe that I do not want to specify the two characteristics PR_TOTVAL_USD and PR_TOTVAL_EUR for overall value in the same release class, as this would lead to double maintenance for a large number of release strategies. Also consider the maintenance when new countries with new currencies want release strategies.
3. Observe that I only want to use overall release.
What I'm trying to avoid is having to continuously translate local business USD overall value limits to limits in the currency chosen for the overall value characteristic. If this for example is specified in DKK, this would lead to a need to adjust the overall value limits as soon as the exchange rate between USD and DKK changes in the system.
Please consider this simple example:
Local requirement is that USD purchase requisitions should be blocked when the USD value is above 1000 USD. However in my release strategy I would have to maintain a value of >5365 DDK, if DKK is chosen as the currency for overall characteristic.(e.g exchange rate 5,365).
Next month the currency exchange rate in the system between USD and DKK has changed, and therefore I would have to go into CL24N and maintain the value to reflect the new exchange rate between USD and DKK. Lets say it has gone up to 5,435. I would now have to maintain a value of > 5435 DKK in my release strategy to correctly reflect the local business requirement of 1000 USD.
So if anyone could please explain why SAP has taken the decision to make the Release class for overall release client specific that would be much appreciated and awarded accordingly. Also if you have any suggestion on how I could obtain the above scenario on maintaning overall value limits in different currencies than that would be awarded to.
BR Jakob F. Skott

You can give feed back to Apple from the iTunes drop-down menu in the iTunes menu bar..
You can also contact the iTS Customer Service from the links on this page - http://www.apple.com/support/itunes/store/
MJ

Internal change after Release

Hi
Scenario
We are using internal order (Investment) for capital budgeting.
We have created two roles a)Z_FI_IOCREATION for order creation, change
and display and b)Z_FI_IORELEASE exclusively for releasing the order.
End users create the order and their HOD's release the oders.
Requirement
End users can change the order n number of times but only before
Release of the order.
After release of Order if the order is changed by end user the orders
should be available for Release again. This way we contol the change of
orders after approval. How this can be addressed.
Regards
Ganesh

Hi,
Try whether you do not give authroization for change of Internal Order through transaction code KO02.
Trust this helps much!
Cheers!

PO change after Release

Dear All,
One our client wants after release of the PO (we have only 1 level), system should not allow to chage the PO.will it possible?
Regards
venu gopal

hi
use shortcut as
OLME>Purchase Order>Release Procedure for Purchase Orders>Define Release Procedure for Purchase Orders>Release indicator-->maintain 1 in 3rd column
Vishal...

Add estimated cost in PM Service order after release of order.

I have released the PM service order. Now I need to add the estimated cost in service order. . Please tell me a way to do so. I have only released the order and no other transaction has been done.

ANIMESH KUMAR,
AS standard you cannot change the estimated cost value after release (REL).
However, I have seen two work arounds:
- Copy the field onto the Enhancement tab via user-exit IWO10018
- A bespoke TCode/program to directly update the AUFK-USER4 field
PeteA

Firefox only works after I re-boot my computer

I just got a new computer last week. It is running Windows 8 - 64 bit. I installed Firefox, used it for a week, set up my bookmarks, etc. and it worked fine. The other day when I logged in and opened Firefox, I couldn't click on anything - nothing would happen - it was like it was frozen. I went into Internet Explorer and also into Google Chrome and they both worked fine - I could click on things and it would do what it was supposed to do. So, I re-booted my computer and then Firefox worked fine. Same thing the next day, Firefox only worked after I re-booted my computer...and also today, same thing. Why is it frozen when I first go into it, but if I re-boot the whole computer, it works? Has me baffled. Any help would be appreciated, because it is my favorite browser. But if this keeps up, I won't be using it anymore. Thank you!
I have my home page set to Yahoo, so that's where it goes when I open it. When I get there, I can't click on my e-mail, nothing in the toolbar, it's totally frozen.

Hello,
'''Try Firefox Safe Mode''' to see if the problem goes away. [[Troubleshoot Firefox issues using Safe Mode|Firefox Safe Mode]] is a troubleshooting mode that temporarily turns off hardware acceleration, resets some settings, and disables add-ons (extensions and themes).
If Firefox is open, you can restart in Firefox Safe Mode from the Help menu:
*In Firefox 29.0 and above, click the menu button [[Image:New Fx Menu]], click Help [[Image:Help-29]] and select ''Restart with Add-ons Disabled''.
*In previous Firefox versions, click on the Firefox button at the top left of the Firefox window and click on ''Help'' (or click on ''Help'' in the Menu bar, if you don't have a Firefox button) then click on ''Restart with Add-ons Disabled''.
If Firefox is not running, you can start Firefox in Safe Mode as follows:
* On Windows: Hold the '''Shift''' key when you open the Firefox desktop or Start menu shortcut.
* On Mac: Hold the '''option''' key while starting Firefox.
* On Linux: Quit Firefox, go to your Terminal and run ''firefox -safe-mode'' <br>(you may need to specify the Firefox installation path e.g. /usr/lib/firefox)
When the Firefox Safe Mode window appears, select "Start in Safe Mode".
:[[Image:Safe Mode Fx 15 - Win]]
'''''If the issue is not present in Firefox Safe Mode''''', your problem is probably caused by an extension, theme, or hardware acceleration. Please follow the steps in the [[Troubleshoot extensions, themes and hardware acceleration issues to solve common Firefox problems]] article to find the cause.
''To exit Firefox Safe Mode, just close Firefox and wait a few seconds before opening Firefox for normal use again.''
When you figure out what's causing your issues, please let us know. It might help others with the same problem.

TS5198 Unsupported hardware only mentioned after release?

Similar Messages

Maybe you are looking for