UC500- Outbound SIP Routing Question

We have a UC540 that is receiving its trunking from a cloud based sip server.  They have two trunks on the server, one for voice traffic and one for fax traffic.  Inbound this works fine but all outbound traffic goes over the 'voice' trunk.  Is it possible to route outbound traffic, from the fxs ports that the fax machines are connected to, onto the 'fax' trunk of the sip server?  The sip server only provides one ip address, with unique registration to each trunk.

Hey guys,
Thanks for the response.  Let me clarify my question a bit.  I get the translation routing part and that is very helpful but I am still stuck on how to point a dial peer to the 'fax' trunk on the sip server.
A typical dial peer on the switch looks like this:
dial-peer voice 1022 voip
corlist outgoing call-national
description **CCA*Generic Locale*Long Distance**
translation-profile outgoing SIP-Trunk-Out
preference 1
destination-pattern 91[2-9]..[2-9]......
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
and the sip-ua looks like this:
sip-ua
credentials username 7xxxxx5 password xxxxx realm xxx.xxx.xxx.236  (voice trunk/user ID on the sip server)
credentials username 7xxxxx6 password xxxxx realm xxx.xxx.xxx.236  (fax trunk/user ID on the sip server)
keepalive target ipv4:xxx.xxx.xxx.236:5060
authentication username 7xxxxx5 password xxxxxx
no remote-party-id
retry invite 2
retry register 10
timers connect 100
timers keepalive active 100
registrar ipv4:xxx.xxx.xxx.236 expires 3600
sip-server ipv4:xxx.xxx.xxx.236:5060
connection-reuse
host-registrar
Thanks,
Chad

Similar Messages

  • CUCM SIP Route Pattern Discussion

    Hello,
    I have some questions about SIP route pattern configuration but the main question is I can configure SIP route pattern to match any IP address. so if the user dial any ip address it will hit this route pattern.
    Regards,

    Help -> For this page
    IPv4 Pattern
    (Required) Enter the domain, sub-domain, IPv4 address, or IP subnetwork address.
    For Domain Routing pattern usage, enter a domain name IPv4 Pattern field that can resolve to an IPv4 address. The domain name can contain the following characters: [, -, ., 0-9, A-Z, a-z, *, and ].
    For IP Address Routing pattern usage, enter an IPv4 address the IPv4 Pattern field that follows the format X.X.X.X, where X represents a number between 0 and 255.
    For the IP subnetwork address, in Classless Inter-Domain Routing (CIDR) notation, X.X.X.X/Y; where Y is the network prefix that denotes the number of bits in the address that will be the network address.
    Tip   
    If the SIP trunk supports IPv6 or both IPv4 and IPv6 (dual-stack mode), configure the IPv6 Pattern in addition to the IPv4 pattern.

  • CVP Opsconsole: Patterns for RNA timeout on outbound SIP calls - Dialed Number (DN) text box does not take any input

    Hi there,
    I'm having problems modifying the 'Dialed Number (DN)' text box under 'Advanced Configuration->Patterns for RNA timeout on outbound SIP calls' of the SIP tab in the Cisco Unified Customer Voice Portal 8.5(1) opsconsole. In a nut shell, I need to change the RNA timeout but some reason when typing into the Dialed Number text box, the input is not taken. The reason I want to change this settings is because my ICM Rona is not working with CVP:
    https://supportforums.cisco.com/thread/2031366
    Thanks in advance for any help.
    Carlos A Trivino
    [email protected]

    Hello Dale,
    CVP doesn't allow you to exceed the RNA more than 60  Seconds. If you want to configure the timer for DN Patterns you should  do it via OPS console, It would update the sip.properties files in  correct way, the above way is incorrect.
    Regards,
    Senthil

  • SIP Trunk Question - Outbound Calls Fail

    Hi Folks,
    I am using a Cisco 2821 as a router that will convert a SIP trunk to an E1 PRI. Si my setup is:
    SIp-Trunk > 2821 Router > E1 port on 3900> CUCM
    Inbound calls are working fine, but outbound are failing. I am starting to think its due to transcoding issue on the SIP-GW maybe (there is nothing configured on it for XCODE etc).
    I think my configuration is fine as I am able to recieve calls inbound. Just outbound fail.
    Here are the debugs from the SIP-GW:
    "Debug CCSIP calls"
    *Nov 26 18:50:50 UTC: //929/F9E88693801B/SIP/Call/sipSPICallInfo: 
    The Call Setup Information is:
    Call Control Block (CCB) : 0x4BB4F194
    State of The Call        : STATE_DEAD
    TCP Sockets Used         : NO
    Calling Number           : 1528xxxx
    Called Number            : 909
    Source IP Address (Sig  ): 172.29.x.xxx
    Destn SIP Req Addr:Port  : 10.200.7.157:5060
    Destn SIP Resp Addr:Port : 10.200.7.157:5060
    Destination Name         : 10.200.7.157
    *Nov 26 18:50:50 UTC: //929/F9E88693801B/SIP/Call/sipSPIMediaCallInfo: 
    Number of Media Streams: 1
    Media Stream             : 1
    Negotiated Codec         : No Codec   
    Negotiated Codec Bytes   : 0
    Nego. Codec payload      : 255 (tx), 255 (rx)
    Negotiated Dtmf-relay    : 0
    Dtmf-relay Payload       : 0 (tx), 0 (rx)
    Source IP Address (Media): 172.29.5.210
    Source IP Port    (Media): 16786
    Destn  IP Address (Media):  - 
    Destn  IP Port    (Media): 0
    Orig Destn IP Address:Port (Media): [ - ]:0
    *Nov 26 18:50:50 UTC: //929/F9E88693801B/SIP/Call/sipSPICallInfo: 
    Disconnect Cause (CC)    : 28
    Disconnect Cause (SIP)   : 484
    Can anyone shed some light on the area that I need to focus on? This is my first attempt at SIP and I am confused :)
    Thanks.

    Hi
    909 is what I meant to dial as that is the help desk for the telco. 
    I tried mobile numbers as well getting the same error codes. And international numbers. 
    If it's based on the called number being wrong then I guess I will have to play with the calling party ID and call type as well... Maybe this is causing it to fail?? 

  • SIP Redundancy Question

    Hello,
    I have set up 2 CUBEs with sip trunks to a provider from my CUCM 8.0.3.  everything is working fine with exception of fall over to the second sip trunk in the route list.  Meaning, if i bring the first CUBE down the second one never routes the outbound calls even though it is second in the route group.  Does anyone know how to get this working properly?  or...does this set up just not work?  How can I get the call manager to notice that its first outbound choice died?
    Thanks,
    Ed Vazquez

    Hi,
    Wrong forum. You need to move this question to IP Telephony forum...
    Regards
    Please rate all useful posts
    Favor calificar todos las respuestas útiles.
    LinkedIn Profile: do.linkedin.com/in/leosalcie
    MDGDP, CCNA, CCNA Voice certified

  • UCCE 9 Outbound SIP problem

    Dear All,
    I'm implementing the SIP Outbound Dialer, the architecture is below
    1. ROGGER + Campaign Manager : (version 9.0)
    2. CMPG + CTI Server + CTIOS + MRPG + SIP Dialer : (version 9.0)
    3. CUCM ver 8.6
    4. Gateway + E1 trunk + IOS 15.1(3)T
    The problem is SIP Dialer doesn't call out after successfully loaded calling list into the CampaignManager (checked the log in baImport). I checked the status of SIP Dialer that it Active all (please, see the attach file). But when I check the log on MRPG it said that "Failed an attempt to ACTIVATE the Peripheral's Routing Client ". I don't sure that this is the cause of the problem or not, I've re-checked configuration on MRPG manay times but nothing strange. Anyone found this problem before please, suggest.
    BR.
    Winai K.

    Hi,
    Except for 15.1(x)T train other IOS versions do not have the capability of doing the CPA analysis (determining voice \answering machine \ fax etc) effectively.
    As a result it is recomended to use above code.
    Thank you
    Anuj

  • Patient reminder outbound sip dialer script

    Hi Experts,
    I have setup some UCCX 8.5 system ACD scripts with agents on CUCM 8.6 for a healthcare facility.
    The only item remaining is an outbound dialer option, which can automatically call out
    patient phone #s and play a recording with Patient name, date and time of appointment, etc..
    On the back-end, these appointments are stored in an Oracle based Medical application.
    I am trying to figure out what format I need to export the data from Oracle, so it can be imported
    into the UCCX ?
    here are the pieces of the puzzle:-
    1> Oracle DB will export a daily/weekly appointment list, which I want to import into UCCX.
    2> the hospital receptionist will record the patient names as wav files (they dont have any Nuance integration)
    3> my Outbound dialer script will either import the static file (from the DB), or do a Database DIP
         to query this list of appointment reminders, then create the reminder prompt, and
         complete the call/play prompt after the call is answered....
    Questions:
    > does anyone have any sample script/pointer to this kind of an application integrated with UCCX ?
    > what format do I need to export data from Database in ? (assuming the DB does not support a direct
       connection through UCCX)
    > any other pointers/suggestions are welcome.
    I searched through the support forums, but didnt find this answered before..
    Thanks
    JK

    A CCX script can do a database dip. I am not sure if Oracle is a supported DB for CCX.
    The outbound dialer is more about dialing and send calls to Agents.
    What CCX is missing is a way of triggering a script at regular time intervals. However there are two ways to trigger a script in CCX. The first is by someone dialing in using a route point. The second is via a http access.
    So what you could do is to schedule a job on a Windows server that every minute would make a web access to the CCX server. This would trigger your CCX script which could then do a database dip looking for a user to call. If it finds work it would dial the number, play the messages etc and possibly write the results back to the database. This is nothing to do with the outbound dialer.
    Nuance is a TTS/ASR engine and is pretty simple to integrate, well TTS is pretty simple to setup and use. ASR is a bit more challenging.
    If I was doing this job I would write a Windows service that ran a regular intervals. It would look in the Oracle DB for work. When it found a person to call it would make a web access to CCX to trigger a script and it would pass the information across as parameters. This would be the number to dial, date and time of the appointment, name of the wav file with the persons name and what ever information you need to pass to the script. Depending on how your script works you could have CCX return a result to the Windows service, things like no answer, wrong person, person wants to change appointment. I would do the smart things in the Windows service and keep the CCX script simple.
    Graham

  • SIP UUI Question

    Hi,
    Could somebody please advise as how would we retrieve the UUI (User to User Info) in ICM ? The UUI is being set at the customer PBX (Nortel) and getting passed on to ICM through the PG. I`m trying to retrieve that through either through UserToUserInfo variable ,with no luck.
    Call flow:
    Nortel PBX ---->SIP Trunk -----> Cisco CallManager ---->CTI Route Point----->CCM PG----->ICM
    Raj

    Yes, same trunk will be used for both inbound and outbound calls.
    Let say you create one SIP trunk between CUCM and Asterisk, same SIP trunk here will be used to deliver all calls from CUCM to Asterisk and vice versa.
    When you look at SIP trunk configuration in CUCM, you will get both inbound and outbound call related parameters for appropriate configuration of outbound and incoming call routing.
    Thanks
    Vivek

  • Agent Selection/Routing Question

    Hello:
    I wanted to run a question by the group to get some feedback on a question I have surrounding Agent routing within UCCX (8.5 su4).
    Here is the setup of the environment:
    CSQ1: General
    Routing Criteria: LAA
    CSQ2: Spanish
    Routing Criteria: Most Skilled
    Agent1
    has Skills of General and Spanish. 
    Their competency is the same within both skills.
    Question: Calls are in queue for both CSQ's, although the call in the spanish CSQ has been in queue longer.  And agent 1 goes ready.  Whats currently happening is that agent 1 is getting another call from the General Queue as opposed to getting it from the spanish queue.
    How do I ensure that agent 1 gets the call from the spanish CSQ over the general CSQ?  Each CSQ needs to keep the Routing Criteria the same.
    My thought is that it has to be one of these two items, if not a combination of both.
    Decrease the Competency of all General agents to a (5) and Making the Spanish competency higher then 5.
    in the script, for Spanish Calls use the Set Priority Node to increase Spanish queued calls to be at like a 5, to ensure all spanish calls have a higher priority then general Calls.
    Any feedback would be appreciated! 

    Hi Sean
    All calls on the system if you are not using priority steps already should be answered FIFO... provided that there are agents available in the queue that the first call came in (i.e. they meet the minimum competency). Competency, skills/LAA and all those algorythms only affect who gets the call, not which one is served first. The exception to that is if the competency excludes some agents from the CSQ completely.
    So a call that arrives in 'Spanish' first should be routed to agents first, as long as there are agents available. Does the same apply if the agent is 'ready' but on a call for example? E.g. call voicemail as the agent, then put a call in to spanish, then one in general, and see which one comes through first.
    Priority will work, but will mean that Spanish calls alway queue jump. Priority is absolute, so a p2 call will jump in front of all other lower-priority calls regardless of how long they have been there.
    If you just want first-come-first-served, then that's what you should have by default.
    Aaron

  • BT Infinity - HG612 and second router question

    Hi,
    I've got an odd question. I have BT Infinity and have the HG612 VDSL modem. Does anyone know if and how it can be configured to bridge its WAN connection to another router? For work I need site-to-site VPN access, which is performed by this other router. Unfortunately it needs to own the WAN address, so I need to configure the HG612 to bridge the address with it. Has anyone does this? Is the HG612 even capable of doing this?
    I can't find any user manuals on it.
    Thanks, 
    Simon

    Hi Andy and welcome
    In THIS POST Phil recently wrote.-
    "Very proud of myself this afternoon.  I'm not much of an expert when it comes to DIY but I have managed to hardwire the router from the back of my house to the office on the first floor at the front.  After much contemplation, I decided to buy some external cat5e cable and run this along the same points as the SKY feed.  The result looks pretty good and I can now get 37.5Mbps upstairs as well as down. Result."
    Phil is very friendly I am sure if you have any questions it might be worth dropping him a PM ( philt1808 ) PM = Private Message if you click on the link philt1808 in brackets on the right you'll see SEND THIS USER A PRIVATE MESSAGE click on that.
    Mention it's PC's fault your contacting him... 
    Edit this thread has some info on cables http://community.bt.com/t5/BT-Infinity/Master-Socket-gt-Modem-gt-Hub-Router-cabling/td-p/408439
    Please Click On any Text in Blue as that automatically links to information.
    PC (NDEGR)

  • ESB routing question

    Hi,
    I have a question on the service that we are writing for the ESB. We are doing some simple transformations on the messages that the ESB consumes through AQ, then outputs to various end points(file adapter, soap adapter, DB adapter) after going through a routing service.
    My question is that it seems like the message delivery to the end points is very sequential. I thought that the message was suppose to hit all the end points, regardless of it's state, and move on to the next end point, and only retry the end points that failed. But this does not seem to be the case. Is there a way to achieve this with Oracle ESB?
    Thanks.

    The issue is that the routing service is sequential. We have a few adapters on the same routing service, and we observe that the message moves through the adapters sequentially.
    We are going to try to break out the routing service and end points so that each process dequeues from AQ, goes to one routing service, and one end point. Hopefully this way, there won't be any blocking, and all RS and endpoint can execute independently. The concern then is having a multi-consumer AQ, and I'm not sure if there are any issues with it.

  • CSCtq10477 - Callmanager 9.1 can't make outbound calls, Route List gets error 41 - All devices busy

    Hi all
    I seem to have run into bug CSCtq10477 and maybe CSCul71689 and CSCum85086, where calls can be received from an MGCP gateway, but fail outbound with Callmanager logs showing
    03095771.002 |17:34:14.103 |AppInfo  |RouteListCdrc::null0_CcSetupReq - Terminating a call after the RouteListCdrc cannot find any more device.
    03095771.003 |17:34:14.103 |AppInfo  |RouteListCdrc::terminateCall - No more Routes in RouteListName = RL_OUTBOUND.  Rejecting the call
    03095771.004 |17:34:14.103 |AppInfo  |RouteListCdrc::terminateCall - Sending CcRejInd, with the cause code (41), to RouteListControl because all devices are busy/stopped.
    03095771.005 |17:34:14.103 |AppInfo  |GenAlarm: AlarmName = RouteListExhausted, subFac = CALLMANAGERKeyParam = , severity = 4, AlarmMsg = RouteListName : RL_OUTBOUND, Reason=41, RouteGroups(RG_OUTBOUND)
    and a Route List exhausted alarm appearing in RTMT.
    Resetting the MGCP gateway in Callmanager, bouncing the serial interface, E1 controller and No MGCP/MGCP has no impact.  I could also see the circuit was not full.
    We have got round this by removing the gateway from the Route Group and pointing the Route Patterns directly at the gateway and this works.  I can see two of the bugs above are fixed in the latest 9.1.2SU3 code (9.1.2.13900-10), but I don't see CSCtq10477.  This bug document shows some 9.1 code is OK, but not this one.
    9.1(1.21020.1) - Not listed for download, is this an ES?
    9.1(2.10000.11) - Not listed for download, is this an ES?
    9.1(2.10000.28) - 9.1(2) - but not shown in the release notes for 9.1(2) either.
    Does anyone know if the Release notes just missed this out, or does the bug document need the Fixed versions to be updated?
    Thanks

    Hi,
    9.1(1.21020.1)  is an ES.
    9.1(2.10000.28) is the base version of 9.1(2) so this bug will be fixed in this version or any higher version of 9.1(2).
    Upgrading to the latest ES or 9.1(1) or 9.1(2)SU3 would take care of this bug.
    HTH
    Manish

  • 1760 Router Questions

    Essentially, I've been studying for the CCNA and I've decided to purchase some older equipment to set up in my house so I can get some additional practice with the IOS interface. I've been looking at 1760 routers on ebay, and it seems like a pretty good place to start as I would like to actually use the devices in my current LAN, rather than simply setting up a lab.
    My question is, could I take a 1760 and connect it to my cable modem, and then connect a switch (say a 2950 that I'll purchase a later date) to another interface? What add-in cards will I need to make this possible?
    Here's a graphic representation of what I'd like to do.
    If the 1760 isn't a good choice for this sort of setup, what would you reccomend? I'd prefer 100Mbit/sec capable routers if possible.
    Thanks for the help/suggestions.

    Taylor,
    if you have a VLAN capable switch and proper IOS support, you can configure PPPoE client on a subinterface hence you can use the 1760 (or any other router) to connect to the ISP and route between VLANs.
    This is my current setup:
    interface GigabitEthernet0/1
    no ip address
    duplex auto
    speed auto
    interface GigabitEthernet0/1.4
    encapsulation dot1Q 4
    ip pim dense-mode
    ip igmp query-interval 125
    pppoe enable group global
    pppoe-client dial-pool-number 9
    interface Dialer9
    mtu 1490
    bandwidth 4672
    bandwidth receive 480
    ip address negotiated
    ip nat outside
    ip virtual-reassembly in
    encapsulation ppp
    ip policy route-map RM-loop1
    dialer pool 9
    crypto map CM-1
    crypto ipsec client ezvpn witopia_IAD
    As you can see I use a subinterface to do PPPoE client and have the Dialer 9 interface receive the public IP address then I route traffic to other dubinterfaces. I used to do that on a 1751 nd on a 1721 this is now a 1921.
    You need to ensure the pppoe client on 803.1q subinterfaces is supported in the ios version you run and obviously that 803.1q subinterfaces are supported.
    You can do all of that in the cisco feature nav.
    Enjoy
    Fabio

  • 2 more router questions

    Hi everyone. I had a couple questions about some readings on my FIOS Actiontec router. Sorry if this is basic stuff, but I am still learning:  
                        1) On the my main page where it shows my computer's wireless connection it reads that remote access is enabled. What does this mean?
                        2) On the Wireless Status page it shows something called WMM is enabled. What is WMM?
    Thanks in advance for any help.
    Solved!
    Go to Solution.

    Well here is an update: I made a lot of changes on my computer based on the advice given to me on this forum. Based on what I changed, I would say it was a combination of remote microsoft and remote verizon processes/services running on my computer. Now that I have disabled or blocked many of those processes and services, the router no longer displays "remote access enabled".    Thanks to everyone who responded for your very helpful advice and information.

  • Routing question

    Hi,
    I've made a proxy Service in aqualogic, that contacts another webservice, with a different WSDL than the proxy.
    How do i define the messageflow for this?
    I need to map the proxy requestxml to the business service xmlschema, for which I have build an XQuery for. Thats not the problem. Its the messageflow, the exact syntax in the modeling.
    PSRequest1->XQuery->BSRequest->BSRespons->XQuery->PSRespons
    How would i build this in the messageflow editor?

    The xml transformations can be done in XQuery mapper tool.
    I contacted my route node the following way, after receiving the message through my proxyservice.
    I did this by changing the body of the incoming xml message to the format of my business service.
    Then i reverted it back.
    So the messageflow is the following.
    Incoming message through PIPELINE.
    Make a stage in inbound and outbound flow in the pipeline.
    In the stage alter the body of the incoming XML to the format of the Business service.
    Do the reverse in the outgoing stage.
    The xml Body of the incoming/outgoing message has a default variable named "body"

Maybe you are looking for