Unable to connect C4780 to router VM DG280

My C4780 printer is unable to connect wirelessly to Virgin Media's NetGear DG280 router from my Mac. Printer offline status is displayed. Previsously had BT Hub 2.0 and same Mac and printer worked fine. Anyone have an idea why the printer and router wont speak to each other? Thanks
This question was solved.
View Solution.

You will have to re-install the printer. First, from the front of the printer: Setup [Scan] > Network > Restore Network Defaults.
Now, get the latest software for your printer from the "Support & Drivers" link at the top of this page and run the installer again. You will have to temporarily use a USB cable for your computer to tell the printer about your new router (network).
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Similar Messages

HP Officejet Pro 8000 Wireless: HP printer unable to connect to wireless router.

Installing new printer, getting error msg saying HP printer unable to connect to wireless router. MAC address filtering may be enabled on your wireless router which can prevent HP printer from connecting to your wireless network during setup.
SOLUTION says: If MAC address filtering is enabled and you would like to keep it enabled, you must add the MAC addressof your printer to the list of permitted devices for your wireless router before continuing.
My router is WD My Net N900 Router. MAC filtering is diabled. My security mode is WPA/WPA2 Personal.
I have run out of ideas to try and fix the issues, would appreciate some help.
Thanks,

Hi Jamshidk
I am surprised you are getting that message and you checked the router settings and it is showing that the Mac Filtering is disabled.
I would suggest connecting the printer to the router with a ethernet cable to get a valid IP address and then setup the wireless.
Print a configuration report.
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&dlc=en&docname=c01554589&lc=en&product=3760410&tmp...
Type the IP address from the configuration page in the address bar into internet explorer browser. This will open the embedded web server for the printer. Click on the Networking tab, on the left hand side select wireless. After this is setup and applied, disconnect the ethernet cable.
Should be on the wireless network. Takes about 1 minute.
Run the add printer wizard.
Go to start, devices and printers and select add a printer. (Win 7)
Test the printer.
If you need more assistance just let me know.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

WRT54G: Unable to connect to the Router!

I have set up my router exactly as told in the setup wizard, but when I get to step 8, I encounter a problem and I get the following error message:
Unable to connect to the Router!
Check that your Router has been connected to the computer, and that your Ethernet adapter is working!
Oddly, my wired internet works just fine through the router, but my wireless doesn't because I can't complete the setup. All the lights that are supposed to be on are on and not blinking or anything.
What do I need to do to fix this?

you can actualy configure the router without using a setup cd.. you can try accessing the router setup page using your working computer that is wired to the router. just go to internet exp. type 192.168.1.1 on the address box.. it will ask for password- just type admin. go to the wireless menu - change the ssid to any name that you want to name your network. try to view wireless networks on your wireless pc and check if you can see the name that you set. connect to it..
you can check if it works.
Piz Brother,
>>>--DARK_TEMPLAR -->

Unable to connect to the router! (wrt54g v. 2)

I just got a router from a garage sale; it was still in the box and everything.
Well, I tried hooking it up to my modem and computer to get wifi, but I can't get it to work.
This is the setup:
modem -> router -> computer
I can access the internet when the setup is this way, but there's no wifi, and I can't access 192.168.1.1 or set it up using the CD it came with. When I go through the setting up process with the CD, I get this error message that says "Unable to connect to router! Check that the router has been connected to the computer, and that you're ethernet adapter is working."
When I try to go to 192.168.1.1, it says "The connection has timed out." I can't ping it either.
I've also tried resetting it several times, but that doesn't do anything.
Someone please help!

Hi sylentknight and welcome to the forums!
You said that you are able to connect to the internet with this set-up: modem -> router -> computer right? So does that mean that you can ping the router when it is connected directly to your computer? Reason why I'm asking is if it does work, you can try to configure the router for the wireless settings while it is directly connected to the router first then try to go wireless. Please let me know if understood your post correctly.

Hp photosmart 5520 unable to connect to wireless router

The printer worked fine-I went on vacation and now it won't work. I ran the wireless network test and it said"hp printer is unable to connect to your wireless router". The wireless router is connected and running fine. My wireless hp computer (windows 7) works just fine.
The report satd "network name ssid found" said FAILED
But "current configuration" showed the SSID
can anyone offer a fix?
Help
colleenmercy
This question was solved.
View Solution.

Hi colleenmercy,
On the network menu, select Restore Network Defaults. This will clear the current network settings and allow you to reconnect the printer to the network. You can use the wireless setup wizard or reinstall the HP software to reconnect.
I was an HP employee.
Please mark the post that solves your problem as "Accepted Solution"

Airport unable to connect to ActionTec Router

Hello all,
It seems everyone is having similar issues with their Mac's being unable to connect or having issues connecting to their routers. My neighbor is one of them. I'm a PC guy, so I know little about macs.. But I've learned within 1 day that His issue is common with everyone on this page.
He was using a 2WIRE### Router purchased through AT&T/SBC for his DSL Connection. It had died on him 3 days ago. yesterday we attempted to replace it with a new Actiontec DSL Wireless Gateway (router). On first start up, we gave the network a SSID name and no security. His Wife's PC notebook connected fine, and I being next door, was able to connect fine. However his Macbook could not.
After hours of troublshooting, I learned that Changing the channel can fix the issue. I did this, and after a restart on both ends, I had it finally begun working. Today, he was unable to get on the internet without using Ethernet cable, again.
I am unsure of how to resolve this issue. I'm not even trying WEP or any security right now since I cannot seem to connect to it at all.
Any advice anyone can give me would be great. But so far all i've seen as possible solutions have been: change the SSID name, Remove Password making it open, and Change the channel.
Anyone beleive that Updateing firmware would help? I heard that downloading Macbook updates seem to remove their connections as well.
-Disgruntaled
Jeb
Mac Book Mac OS X (10.4.10)

I have updated information:
I've spoken to both my ISP and Apple directly. They've replaced my Airport Card and my airport extreme base station. I am still not able to log on via the internet.
I have heard from a local store that there has been problems before with Macs, wireless internet, and ISP's that use PPOE to dial up. If I were to switch internet companies I would be able to log on no problem (so he says).
Of course my issue now is, Apple can't fix it, and my ISP won't help as all they will do is see if I can log onto the internet via regular DSL Line, which of course I can.
I'll let you know if there is a trick or any sort of additional information I can offer.

Unable to connect to netgear router and internet

I've installed Solaris 10 1/06 (x86) on a system running an intel mainboard model D865PERL. This has a built in ethernet controller ( Intel 82547EI gigabit lan controller) and the mainboard appears on the bigadmin hcl as being supported. The OS recognizes the built-in NIC as e1000g0 but during initial installation it attempts to configure e1000g0 first thing then responds with "skipped interface e1000g0" then proceeds with the installation.
I choose Networked and run through the installation (or following a sys-unconfig) selecting to enable DHCP but it returns "Could not contact a dhcp server on the network interface e1000g0." I then have to set it up staticly to resume the configurator. I specify the e1000g0's ip address as 192.168.0.5 with a subnet mask of 255.255.255.0. I choose not to enable IPv6 (ive tried it with IPv6 enabled) and no Kerberos. I attempt to specify DNS for name service and use my internet providers domain name (both the name and the resolved ip address associated with it) with the two DNS server ip addresses resolved by the WAN setup on the router (Netgear FR328S), selecting no search domains. But it is unable to locate my hostname on the provided DNS's i entered. dunno why it would say that, it really doesn't matter does it? Anyway, I specify no name service to proceed. i choose no to the question in regards to overriding the system's default NFS version 4 domain name to continue.
It knows it has a cable connection but I'm unable to see the router, even though ive specified 192.168.0.1 as the default route (ive also tried setting it to detect the default route on reboot but it fails). The router doesn't see the NIC as a connected device either (im setting here on another computer running xp :() Ive tried disabling the DHCP server feature on the router and I still cant see it. Ive tried setting the NIC's ip address and MAC address as reserved in the LAN setup on the router (this works for my winXP drive where I need a static IP address and also have access to the internet). I've tried leaving the reserved IP address assignment (attached to the NIC's mac address and host name that i specified) with DHCP enabled but I'm still unable to resolve an IP address from the dhcp server. I made sure the router had the latest firmware and went through the configuration with a fine toothed comb, so to speak. nothing seems to work.
I tried to connect directly to the internet device, removing the router and it still fails to resolve an ip address via dhcp. what am i missing here? Ive run through this multiple times now and im at a loss. Ive also referenced sun's System Administration Guide: IP Service to try to resolve the issue but im now all I'm doing is going in circles.
# ifconfig -a
lo0: flags=2001000849<UP, LOOPBACK, RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
e1000g0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 192.168.0.5 netmask ffffff00 broadcast 192.168.0.255
ether 00:13:20:47:6c:48
# netstat -rn
Routing Table: IPv4
Destination Gateway Flags Ref Use Interfacd
192.168.0.0 192.168.0.5 U 1 0 e1000g0
224.0.0.0 192.168.0.5 U 1 0 e1000g0
default 192.168.0.1 UG 1 0
127.0.0.1 127.0.0.1 UH 4 85 lo0
# prtconf -pv
Node 0x000019
compatible: 'pci8086,1019.8086.301f.0'.....etc
model: 'Ethernet controller'
subsystem-vendor-id: 00008086
subsystem-id: 0000301f
vendor-id: 00008086
device-id: 00001019
name: 'pci8086,301f'

Couple of suggestions:
Work first on seeing the router, using a static IP and pings.
Forget about DNS, DHCP, etc for now. If you don't see the router, nothing is going to work.
You don't need to reboot or do sys-unconfig every time. Just change your settings using ifconfig and route add. Actually, you don't even need to set the route to be able to ping something inside your subnet.
By your output of ifconfig, it seems that the NIC plumbed correctly.
In the Solaris machine, try pinging your own IP address to make sure it responds and you don't have any issues with the NIC/driver.
Make sure the cable and port in your router work. If you can use them with Windows, you should be able to use them with Solaris. Unless...
Try using a crossover network cable to connect the Solaris computer to the router. This is personal experience: I had a Blade 100 that would not see my router. After a couple of hours of trying just about everything, I used a crossover cable and voila! it worked. Why? I don't know :) , but it worked...

Setup WIzard error. Unable to connect to the Router.

All the connections are correct. I am able to connect to IE and FireFox with ethernet and connected my nook via 'Linksys'. I opened using ISP address and set up security. Is there more in the setup that I need to do?
Solved!
Go to Solution.

Hi. Are you still getting that error after you setup everything on the router? Is wired internet working already? Are you replacing an old router? If you still encounter that error, you can download the updated software version for your router. It is best to wire your computer directly to the modem for that and run it from there. You may have to reset the router back to defaults by pressing its reset button down for 15 seconds so that you can start afresh with the setup. I have here a link for you that might help you regarding the software:
Cisco Connect error codes
http://homekb.cisco.com/Cisco2/ukp.aspx?vw=1&docid=8c48ffab84714adb992ca2bf5dd9a529_Cisco_Connect_Er...

Airport extreme unable to connect to new router

We just received a new router from our cable company. The old router worked with our airport extreme just fine. After hooking up the new router the airport extreme could not connect to it. I received the following error "error occurred while trying to access the apple wireless device. Make sure your connection is valid Error -6753" So then I tried to power off and reset the Airport extreme. The button was stuck on my reset button. I did figure that out and was able to click the button. But even if I would hear the audible click when i held down the reset button the amber light never flashed rapidly? Not sure what else to do. I have turned off the modem, unplugged the router, plugged them back in. etc. I just don't know where to go from here.
Thanks!
jodi

Were you able to get the AirPort Extreme to reset back to factory default settings, as LaPastenague detailed?
The amber light needs to flash rapidly for about 6-8 seconds during the process to indicate that the reset is taking place correctly. Once you release the reset button, the light will stay solid amber for 15-20 seconds or so, then change to slow blinking amber.
We are a bit confused as well, since in your first post you mention that you received a new router from the cable company, then later in the post, you mention that you have a (separate?) modem.
In the most recent post, you mention that you have a new modem. Is the new router from the cable company the same device as the new modem? Or, do you have a new modem and another new router in addition to the AirPort Extreme?
Can you clarify on exactly what devices that you have? Make and model numbers would help. We know that you have an AirPort A1408.

Unable to connect C4780 with Mac Pro wirelessly

When i tried to conner Printer C4780 wirelessly to Mac pro it says that the selected printer software isn't from the manufacturer and may not let you use all the features of your printer. The software that i installed is one which i received when in brought printer in PC World in UK. It does connect with USB but not wireless.

Hi @Krish1840 , and thanks for the reply!
Do the pages come out blank when making a copy as well?
I would suggest deleting the printer from your print system, using this document: Uninstalling the Printer Software.
Once you have deleted it, I would suggest verifying and repairing the disk permissions: About Disk Utility's Repair Disk Permissions feature.
I would also suggest running your Apple updates: OS X: Updating OS X and Mac App Store apps
After the updates, I would recommend readding the printer via OS X v10.9 Mavericks: Installing and Using the Printer on a Mac
Good luck and please let me know how it goes!
Please click “Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks" for helping!
Jamieson
I work on behalf of HP
"Remember, I'm pulling for you, we're all in this together!" - Red Green.

Unable to connect to internet with my WRT54G router

I had no problem until a few days ago. I have it under a secured mode and wanted to unsecure it temporarily. I got into the 192.168.2.1 and clicked the security tab and got a clock that never seemed to come back to i closed the window. I went back into internet explorer and could not get into the internet.  I get a popup in lower right saying Local Area connection. This connection has limited or no connectivty. You might not be able to access the internet or some resources. For more information click this message.
Then I get
Windows could not finis repra the problem because the following actin can not be completed. Renewing your IP address.
I do a setup and get a message
Unable to connect to the router
I try pinging the 192.168.1.1 and it times out.
I do a diagostic and
HTTP Error 12007 connecting to www.microsoft.,com  shows up many times.
I have an Actiontec 701 DSL modem. I can get into the internet using that only.
I've tried resetting the router, I've done   what appears to be a firmware upgrade (lights blink etc), I've tried different power up sequences, I've tried re-booting.
What more can I try?

As of now you are not able to login to your router setup page, and you are getting an error message "Limited or no Connectivity". First you can try is Unplug the Power from your router, wait for 1 min and reconnect the power to your router and check if you connected to the router or still you are getting the same error message.
If still the same problem persist then Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

WRT54 V8 - Unable to connect to router... Help!

Hi Guys!
Not sure what I'm doing wrong, but I'm not able to connect to my router. I'm new to this whole wireless network and have hit a road block.
I put in the CD and followed the instructions. When I get to the point of it detecting my computer settings, I get the following message: "Unable to connect to the router. Check that the router has been connected to the computer and that your ethernet adapter is working."
I was able to connect to the neighbors network from my folks place, so I know it works. I'm guessing if I could get passed that point of the wizard, I'd be able to set up my network...
Any suggestions would be greatly appreciated.
Thanks in advance!!

If your Internet Service Provider is Cable follow this link
If your Internet Service Provider is DSL follow this link

LaserJet Pro CP1525nw cannot connect to new router (Home Hub 2000)

In December, we replaced everything EXCEPT our LaserJet Pro CP1525nw colour printer - new laptop (Dell Inspirion 15), new operating system (Windows 8.1 - 64 bit), new internet provider (Bell) and new wireless router (Home Hub 2000).
Immediately, we were unable to connect to the router. We tried all of the suggestions, including connecting the printer directly to the router - which worked, until we disconnected it and then they could not communicate again.
At the time, the only solution we could find was to connect our printer and laptop via USB cable and print that way - no more wireless printing, so unable to print from phones and iPad, but at least we could print from the laptop.
In the past month, we have become unable to use many of the features on our printer - when we try to select print options, we get the message "HPMSN103.dll has stopped working." So, we can still print, but cannot select options.
We have tried using the CD that came with the printer, and it gets to a certain point and then a fatal error occurs. We have tried downloading the "full solution" printer install program from the HP website, and the same thing happens. We have tried skipping that and just choosing the appropriate printer driver in Windows: if we only use that driver, we get a printer that shows up, but we cannot print if we select it (interestingly, though, we can actually access the printer options!); if we say we have the disc, then we get two printers showing up - we can select print options on the one that will not allow us to print, but not on the one that actually prints. If we try removing one of the printers, they both uninstall and we're back to square one.
So, we WANT to be able to get back to printing wirelessly - after all, we paid (handsomely) for a wireless printer! And we still cannot get our printer and the router to recognize each other. Can somebody help? We don't want to have to buy another printer.
Thanks!

Hi @Capers2 ,
I see that you are experiencing issues setting up the printer on the new router. I will certainly do my best to help you.
Thank you for providing that detailed information.
If the network name has any spaces or special characters, the printer may not recognize it.
The printer is only capable of sending/receiving in the 2.4 ghz band.
If it is set to 5 GHZ network you may need to change to 2.4 ghz. (rename the 5 ghz or shut it off)
The WPA key setting needs to be on AES to work correctly not TKIP.
Multi casting needs to be turned on.
Firewall on router has to have open ports for printer.
If you have Mac Filtering you need to give printer hardware address from Configuration page.
You might need to contact your router company for further assistance to check those settings.
I would reset the printer first to clear out any previous network settings.
Turn the printer off, hold down the wireless button and cancel (x button) while turning the printer back on and don't release the two buttons until the printer stops making noise.
Print out a configuration report and make sure the SSID and IP address are cleared.
Printing a Configuration Page.
The easiest way to setup the printer back on the wireless network is through a Ethernet connection and then switch over to wireless.
Disconnect the USB cable.
Remove any printer software by following these steps:
Go into Devices and Printers , click file then Server Properties, click on the Drivers tab at the top of print Server Properties window. Choose the printer you want to uninstall and click remove. Choose remove driver and package. Any that say Universal PCL 5 or Universal PCL 6 also remove and the Laserjet CP1525nw.
The next screen will give a warning, letting you know that deleting the driver package will remove it from the system. Click yes to say that you are sure you want to do this. (if the printer isn't listed that is OK)
Right click and delete any entries for the Laserjet in the Devices and Printers Window.
Run the uninstall from the CD.
Press the Windows key and the X key together. and select File Explorer, right click the CD for the
printer and left click open in new window.
Connect the printer to the router with a Ethernet cable.
Wait about 1 minute and the printer should have a valid IP address.
Print the configuration page to get the printer's IP address to configure the Wireless.
Type the IP address in Internet explorer's address bar which should open the printer's embedded web services page.
Setup the wireless through here now.
Click on the networking tab, wireless on the left, fill out the network information and apply the settings.
After the confirmation, then disconnect the Ethernet cable.
Now you should have a blue wireless light on the printer in about 1 minute.
Perform a clean boot on the computer and turn off the Antivirus Software. How to perform a clean boot in Windows.
Run the installation again.
If you are prompted to connect the USB cable during the installation, Then immediately after connecting the USB cable, follow the steps in this document to update the drivers so it doesn't error out. A Fatal Error Displays During Software Installation. Then the installation should continue.
Test the printer.
If there is anything else I can help you with, just let me know.
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Unable to connect netgear DG834G wireless to macbook

Hi
I am unable to connect the Netgear Router DG834G wireless to my Macbook. It works fine through the ethernet cable but when i try and connect wireless it says invalid password?

Hi
Changing your ISP won't fix this problem. There is one last thing that's worth a try....
Creating a new "Location":
System Preferences > Network
Select the AirPort from the left hand side
Click on the Locations combo box and select Edit Locations...
Click on + to add a new location, call it "Home" (or anything else you prefer)
Click on Advanced
Select the AirPort tab and enter your network name
Select TCP/IP tab.
Configure IPv4 Using DHCP
Now click on Renew DHCP Lease. After a few seconds you should get an IP address (probably 192.168.x.x)
Click on Proxies tab.
Select Auto Proxy Discovery and Use Passive FTP
Click on OK and Apply, etc.
If this doesn't fix your problem then I suggest your Airport card is failing and you need to visit an Apple Store.
Bob

Unable to connect to 890L Hotspot

I was attempting to disconnect from the 890L in order to obtain a new ip address so I entered the admin at 192.168.1.1, then went to "Wi-Fi Settings" > "Connected Devices" and selected "Disconnect". I am now unable to connect to the router or the admin area for the router.

Sure, disconnect and reconnect from your computer/device. The new attempt to connect will refresh your IP. Chances are that you will be assigned the same IP address as before so it wont be a "new" IP.
Chances are that if your 890L is dropping your devices that its glitching on something temporary. Try to restore the defaults on the 890L to refresh it. There should be a small reset button underneath the back cover by the battery that can do this for you.

Unable to connect C4780 to router VM DG280

Similar Messages

Maybe you are looking for