Unrecognised emulation mode

I have a LPC 229x evaluation board. I wrote a simple application with labview. It sends "Hello world" string to serial port.
When I build the project I get this error message:
Linker error occurred
/opt/ecos/gnutools/arm-elf/bin/arm-elf-ld: unrecognised emulation mode: structure-size-boundary=8
cported emulations: armelf
What's wrong here?
Thanks for your help.

Hi,
LabVIEW Embedded passes this option to the linker: '-mstructure-size-boundary=8'. Apparently, the linker got confused with this option. It would help if we could find out the version you have of arm-elf-gcc (use 'arm-elf-gcc -v' in a console). Also, set a breakpoint in 'LEP_ecos_Phytec_LPC229x_ScriptLinker.vi' and capture the command passed to the linker so we can take a look at it. The command is passed into the Sys Exec Wrap VI as a string.
Michael P
National Instruments

Similar Messages

Changing Emulation Mode

My bank just started offering Mobile Banking but it's not working on my phone. I keep getting an error message and when I talked to the person at the bank, they sent me a troubleshooting guide from the mobile banking provider. It said to enable javascript which I did and says to change the emulation mode from BlackBerry. When I go to Options -> Browser Configuration it shows the emulation mode as BlackBerry, but I can't change it. If I highlight it and scroll left or right, it doesn't change and if I press on the scrollball, it brings up a menu of Call Voice Mail, Restore Defaults, Save Options, Switch Application and Close. Am I missing something to be able to change the emulation mode? Any suggestions would be appreciated.
Thanks.

Hi and Welcome to the Forums!
Websites can be coded to perform better with some browsers rather than others. The BB Browser can appear to websites as several different things...that setting is not where you were looking...rather, from within the Browser App, (BBKey > Options > Browser Configuration > Browser Identification). Changing that to another browser might help your BB interact better with some websites. In combination with all of the other configuration settings, you need to find the combination of all of these settings that works best for the sites you are visiting. Sadly, there is no "best advice" to give as each persons needs are different. But, I typically find that changing the Browser Identification often helps -- most often by changing to FF or IE (if those are available to you...the options vary by carrier).
Good luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Trouble installing Shockwave: Question about Rosetta Emulation Mode

Hi, I just got my macbook a few days ago. I can't access Rosetta Stone (language learning program) due to lack of Shockwave. I tried to install it based on the instructions offered on the Shockwave website, but I was unsuccessful. Here are the instructions they offered me:
Rosetta Emulation Mode
1. Quit out of the browser
2. Go to your Applications folder and control-click on the browser application bundle.
3. In the context menu that appears select Get Info.
4. Under the general heading of the info dialog select "Open Using Rosetta."
5. Close out of the Info dialog box.
Sounds simple, but I can't seem to find the "browser application bundle. A finder search yielded nothing. Please help; I need to finish Ch. 2 by next week (when school starts), haha...

To enable Rosetta in Safari simply open finder, click on Applications, and then find Safari, hold down the ctrl button on your keyboard and then click Safari, a menu will show up, click "Get Info" near the top, a Safari info window appears, check the box that says, "Open using Rosetta." Thats it! Hope this helps!

Rosetta Emulation Mode?

Does anyone know about Rosetta Emulation mode? How do I go to this thing? I have to use this mode for my browser to download and install macromedia shockwave player...but i couldn't locate it....

Kappy wrote:
Your OS X comes with a universal Shockwave plug-in Do not replace it with the PPC version. If you download the most recent universal binary version of Flash it incorporates Shockwave.
Actually, the original poster is correct. Shockwave is still a PowerPC-only plug-in. Take a look at the following link to confirm:
http://kb.adobe.com/selfservice/viewContent.do?externalId=82216d24&sliceId=1
(Flash and Shockwave are similar, to be sure, but there are still some older education and business web apps that require Shockwave.)
That link also includes detailed instructions on how to configure your browser to run in Rosetta. Good luck!

SmartForms w/ Printronix SL4M RFID printer in Zebra emulation mode

Trying to get a basic Smartform to print using a new printer. It is a Printronix SL4M RFID printer that emulates several printer modes, including Zebra.
The printer was changed to Zebra mode, device type in SAP is LZEB2. Configuration printout on the printer shows it in Zebra mode and using a 203 dpi printer head. Configuration is all defaults (command prefix, label prefix, etc).
Output generates in SAP. Spool is ok. Print preview is ok. Completes with no errors in SAP. Physical printer is giving intermittent results. Usually, no output at all. One time, we got half a label that actually contained valid data. Sometimes we get "invalid data" messages on the printer. Last test spit out two blank labels.
Unfortunately the printer is in Germany and I am in the US. Going to try to change the printer to "ZGL QUIET". This is supposed to print out the ZPL code as text. Want to see if any control characters are getting changed. Also checking settings that are code page/language specific.
Looking for any suggestions. Thanks.
Norm

Gave up with SmartForms using the Zebra device type LZEB2. It was going to a Printronix printer that emulates a Zebra. Was not sure if it would work and had to move on. Will go back later and attempt.
Also, Printronix provides SAP device types for use through SmartForms. Others have used successfully. We had problems installing at our current release level.
Switched to SAPscript. Had issues with ZPL control characters being substituted in the default European configuration on the physical printer. Made changes and had some success.
Using one of the international character sets seems to be working.
European character set #300 - Latin 2 8859-2.
It does not replace the Zebra control characters for caret and tilda.
It also does not seem to replace the Printronix control characters caret, left and right curly brackets.
Added commands to the SAPscript layout set. Still need to perform some additional testing, but last tests were successful.
ZPL II command
^CI300
Printronix PGL command
^i300^-

Kms is broken on a mac mini (bios emulation mode)

kms shows up scrambled video on 320m nvidia using the open source nouveau drivers. nomodeset fixes this, but makes you use vesa so that breaks a whole other things. i'm using the the hdmi output with a dvi adapter. how can i go about in troubleshooting this?
straight hdmi does the same thing. im typing this from my hmdi tv with kms off
Last edited by garegin (2012-01-01 01:12:12)

Took to Apple Store and they fixed the unit with a new digital audio card. $49. I'm happy.

Anyone having problems using Photoshop CS2 in emulator mode?

I am about to purchase a new iMAC 20 and I'm concerned about being able to use Photoshop on this machine.
Anyone having a good experience with that setup?
Thanks,
Lou

Thanks really appreciate the response. I will be getting mine with an additional 2GB so I'm hoping it runs as fast as possible given that RAM limitation. I'm disappointed that there is a 2GB limit since I was hoping to buy a machine with at least 4GB. But my only other option was a G5 and I couldn't see spending the money for a fully blown G5 when the newer iMAC may serve me just fine. The higher end PCs are just as expensive anyway and I don't want to stay with PCs - need a change!
Most of what I do is photo editing and presentation. I'm a photographer so I need to have lots of good processing software for working on photos and creating slideshows, albums, etc. I have been a little concerned as to the ability of the iMAC for this kind of work. But, so far the people I know who have them really like them.
Thanks,
Lou
iMAC 20 Mac OS X (10.4.6)

Error in invoking target install of makefile: Oracle8.1.6 on RHLinux7.1

Hello,
How are you?
I am facing some problem to install Oracle 8.1.6 on my own pc on
os Linux 7.1.
I can start installer.Its installing but after 72% installation
complited than its gives following errors.
error in invoking target install of makefile
/u01/app/oracle/product/8.1.6/sqlplus/lib/ins_sqlplus.mk
error in invoking target install of makefile
/u01/app/oracle/product/8.1.6/network/lib/ins_net_client.mk
error in invoking target install of makefile
/u01/app/oracle/product/8.1.6/precomp/lib/ins_precomp.mk
error in invoking target install of makefile
/u01/app/oracle/product/8.1.6/ldap/lib/ins_ldap.mk
error in invoking target install of makefile
/u01/app/oracle/product/8.1.6/network/lib/ins_net_server.mk
error in invoking target install of makefile
/u01/app/oracle/product/8.1.6/network/lib/ins_oemagent.mk
error in invoking target install of makefile
/u01/app/oracle/product/8.1.6/odg/lib/ins_odg.mk
error in invoking target install of makefile
/u01/app/oracle/product/8.1.6/otrace/lib/ins_otrace.mk
error in invoking target install of makefile
/u01/app/oracle/product/8.1.6/plsql/lib/ins_plsql.mk
error in invoking target install of makefile
/u01/app/oracle/product/8.1.6/rdbms/lib/ins_rdbms.mk
error in invoking target install of makefile
/u01/app/oracle/product/8.1.6/rdbms/lib/ins_rdbms.mk
error in invoking target install of makefile
/u01/app/oracle/product/8.1.6/ctx/lib/ins_ctx.mk
After that it shows INSTALLATION COMPLETE SUCCESSFULLY.And
Network Configuration Assistant
has start. Its hang the computer
In log shows error this
Error loading native library libnjni8.so
java.lang unsatisfied ink error:jniGetOracleHome
I stop the same.Than Database Assistant and Creation of database
start.It is complete without
any error.
But when I tried to start svrmgrl its show following error
svrmgrl:error while loading shared libraries:libwtc8.so;cann't
load shared object
Please sir,
Lets give me right direction for these difficulties.I am so much
interested to install same on
my pc.Please do needful.If you are interested to give me direct
answer than my mailid is
[email protected]
Thanking you in advance
Yours truly,
Gitesh Trivedi.
Title : re:Installation of Oracle 8.1.6 on RedHat Linux 7.1
[New] O/S : Linux
Author : Akshay Salkar [mailto:[email protected]]
Type : Statement
Date : Nov 11, 2001 23:50 PT
POST :REPLY (W/QUOTE)
Hi Gitesh,
I face exactly the same problems as you face....
no whatsoever difference...and i am completely stuck as i dont
know what to do...
i have heard from some people (on the oracle discussion groups)
that they have successfully installed oracle8.1.6
how i dont know... but very much eager if any of you all could
help me out.
if you do find a way out and solve the problem ...do plz. let me
know....
akshay.

Just make sure when you type : $ ld
it doesn't give you an error like below
[oracle8i@ns1 oracle8i]$ ld
ld: unrecognised emulation mode: elf_i386_glibc21
Supported emulations: elf_i386 i386linux
If so, in order to workaround with it, don't include
. /usr/i386-glibc21-linux/bin/i386-glibc21-linux-env.sh
in your env. setting. but make sure you include
export LD_ASSUME_KERNEL=2.2.5
After disabling that command, I can install oracle 8.1.7.0.1 on
RH 7.2 without any errors.
I hope this helps ! Let me know if you succeed
k3Nn

IE 11 Enterprise Mode Sites List - Must Force IE 8 Emulation to Default or Disaster

I've gone through about 100 postings thus far and not sure what I'm missing.
I have a scenario where 98% of the sites internal are IE8 compatible and in some cases IE7. I was hoping their was an option to default IE 11 to IE 8 Emulation mode but I cannot get it working. I'm having to add each site manually and set it
to IE 8 mode when in fact I have 1000 sites that are IE 8 and 3 that need IE 11. There is no common domain suffix.
Am I just missing something simple? I have the latest Site Configuration Tool, I've edited manually but by default if you add nothing it defaults to Edge Mode or IE 11. I have to add the site manually as an exclude.
I've been reading up on XML, looking for a code solution or hack. All workstations and Citrix must be upgraded to IE 11 and Enterprise Mode is the only option.
Is there any possible way to force IE 11 to emulate IE 8 mode by default. Something I can set in the XML file that reverses the default. So, in other words I don't want to add 1000 sites of IE 8 mode but 3 to use IE 11.
I just cannot wrap my head around there not being this option.
Example: The two sites below run in IE 8 mode. I want everything to run in IE 8 mode and not have to add but only add for any other exclusion. Otherwise, this is going to be a disaster of a project.
<rules version="2">
<emie>
<domain exclude="false">www.thewindowsclub.com</domain>
<domain exclude="false">www.howtogeek.com</domain>
</emie>
</rules>

Hi Brian,
Perhaps I have misunderstood you.....
you should be only adding intranet or trusted sites domains to the EM List. The rendering/compatibility of public websites is maintained by developers or they have asked MS to put their sites into compatibility mode until they have updated their websites
to not use modern techniques...
for internet domains
the site may already be in the MSCVL (MS Compatibility View List)... Tools>Compatibility View Lists, check "Include updated website lists from MS".
If you see an internet site that does not render correctly in the edge mode of the browser consumers can report it to MS from the Tools>Report Problem Websites.
If you are using EM for internet zone sites (publicly accessible), then you are using it for the wrong purpose....(or you have not checked "Include updated website lists from MS".)
for intranet and trusted sites domains, ie. where on corporate networks you want a business partners domain (eg. Bloomberg.com) to be able to link to or host content from your intranet domain. eg. you may have a portfolio management system (web based)
that uses Bloomberg data feeds or content from one of their services, like asset valuation)....
The system administrators are bound to have a listing of their intranet assets which you can either import or manually add to the EMList (or using the EMList Manager).
Rob^_^

Internet Explorer 11 - Emulation Document Mode and User Agent String Drop Down Menu Blank

Hey
I have a user who has a problem with Internet Explorer 11 where when you go to emulation mode using F12, the Document Mode and User Agent String Drop Down Menu are both blank. On our internal website its works correctly but on all other external websites
they are both blank.
I have had a look at the link below but this did not help as it would not recreate some of the registry keys.
http://answers.microsoft.com/en-us/ie/forum/ie11-iewindows8_1/document-mode-and-user-agent-string-dropdowns/cd34d5f8-7839-4083-af55-05d49ba85190?rtAction=1387560713451
Charlie

Hi,
Please include links to any websites that you are having issues with your questions.
There are some known reasons why the documentMode dropdown appears blank...
not all websites though should have the conditions for this.
f12>Console tab, refresh the page to show suppressed error messages and warnings... (documentMode x-ua toggling is listed)...
IE11 includes improvements for XSS... to link to internet sites from your intranets you need to add those sites (If you really, really trust them) to the Trusted Sites list.
the developer console will list blocked xss requests.
by default IE11 runs in EPM.... in the Internet Zone, while it is not switched on for the intranet zone....
EPM only allows 64 bit Addons and ActiveX controls to run in the context of an IE tab...
so its highly likely that one of your Addons is causing the issue.
the first step in troubleshooting IE issues is to test in noAddons mode.
Regards.
Rob^_^

Cannot start compute emulator through command line in c# /devfabric

Hello,
I have been trying to get the compute emulator to start through c# and had no success.
I am calling /devfabric as my argument
my process is csrun.exe and I include the username and password for my computer and the verb "runas"
I also have the app.manifest <requestedExecutionLevel level="highestAvailable" uiAccess="false" />
I also tried making my process cmd.exe with all the above admin options and call the csmonitor.exe to try to make it start as admin so I can use /devfabric later
But no luck I get this error message:
The Compute Emulator had an error: Compute Emulator needs to be launched with administrator privileges in order to run in full emulation mode. Please restart the emulator with correct privileges
I have no problem with starting the storage emulator with /devstore and I can start the compute emulator manually but I need a way to start it through code.
I am using:
Windows Azure 2.2
Windows 8
Visual Studio 2012 ultimate
Thank you.

It felt like I had to add a password and username to the process before starting it since I need admin rights. but removing that part was what fixed it
What was causing it to ask me for admin rights when I put in the name/password?

GBF en mode frequence list

J'essai de générer un signal sinusoidal variant en fréquence.
pour cela j'utilise l'exemple de national Instrument : NIFgen_sweep_generator.vi
J'entre 1kHz pour la fréquence de départ et 1MHz pour la fréquence finale, pour les frequency steps j'entre 300 et pour la durée par step en seconde j'entre 1s.
Donc l'execution de ce vi devrait me prendre au minimum 300s. Mais ca ne me prend que 600ms. je ne comprends pas le pb?
Merci pour vos réponses
Nathalie

No. You have to enable that as well. You used the registry but it is easier just to update your ADMX files and GPMC and use GPO. There is a second setting to enable users to manually use F12.
Anyone figure out yet how to force the alternate reality? I thought there was a way to implement IE 11 and default to IE 8 Emulation Mode where you have 1000 sites that are IE 8 and pending update but only 3 sites that need IE 11. I really don't
want to have to identify 1000 websites, interview everyone, figure out what sites were IE7 but in IE 8 use compatibility mode when IE 8 emulation mode works for both. I have the latest updates, the latest site configuration. I've been looking at
XML itself, for some type of tag to force IE 8 but by default you have to add the exclusion and it then shows up as IE 8 mode. Is there no possible way to make it emulate IE 8 Mode and the exemption process be IE 11 when 98% of the websites internal
have no lifecycle process?
I think I've read every post and blog at this point. I'm hoping anyone can provide an answer.
Maybe I'm the only one but if you have 2000 websites and no developers update their code then you are forced to implement IE 11 across Citrix and Workstation then you own the problem.
Has no one addressed this? What do you do when 2000 sites use IE 8 and 4 use IE 11. You must upgrade to IE 11 and add the 2000 sites manually? Honestly?
I cannot find anything stating to do this or set this in the sites.xml file to force IE 8 by default and create exemptions for IE 11.
If you even try to google the iesitesxml.xsd file all you get is a bunch of virus warnings.
I've read over 100 links, blogs, forums, and cannot understand how this has never come up.

VMotion in VM-FEX Hypervisor Bypass Mode

Hello,
I know that when vMotion a virtual machine in a VM-FEX with Hyperv Bypass, the environment gets temporarily switched to Emulated Mode...
Question is: ¿is this switch to Emulated Mode and switch back to Hyperv Bypass automatically done? Or rather it needs human intervention?
Thanks,

No, VM-FEX is managed by the fabric Interconnect cluster. For this reason you can't use VM-FEX to migrate between separate UCS clusters.
Regards,
Robert

VT100 Terminal Emulation

I am searching for a VI that supports a VT100 Terminal Emulation Mode
on a PC. I need it to communicate online via PC COM1 to my target system
during the
LabView application is running.

Hi Dennis,
Thanks for your response.
On "haWaitForPrompt" i am receiving -2 which means bad parameter.
the function only works if i let the optionals value empty. But
a default timeout of 100(000) (milli)seconds is to long for me.
Just five seconds are enough for my task.
It is the same bad behaviour if you enter the values in the step module settings
or if you are using a TS numeric variable.
greetings
juergen
=s=i=g=n=a=t=u=r=e= Click on the Star and see what happens :-) =s=i=g=n=a=t=u=r=e=

Rosetta stone via rosetta emulator

I am trying to run rosetta stone (the language program) online version and i get the error.
rosettastone.com/online/code/current_version/Local/ENGlui.cct
I even found the file to try and force it to run in rosetta emulator but when I go to "get info" there is not option for me to force it to go through rosetta emulator.
I checked their FAQ pages and it seems that with the dual core intel it should not be a problem because rosetta would run automatically and decipher rosetta stone program.
Any help would be great!!!
Grant Parkis

I had a similar problem trying to get the web version of Rosetta to run on the MBP. My work around is simple...
I am using the firefox browser and forcing the emulator mode. Then logged in to Rosetta and performed the necessary installation. I found this to be the only way to make it work for me. I hope this helps you.
MBP Mac OS X (10.4.7)

Unrecognised emulation mode

Similar Messages

Maybe you are looking for