Using USB microphone with LE

I currently use an M-Audio FastTrack Pro and an XLR condenser microphone. But setting is all up to record vocals is time consuming for my young son. I was thinking of getting a USB mic with a desk stand for him to use for recording his vocals. Anyone out there using Logic Express 8 and a USB mic? How do I set it up? Any suggestions for a good mic under $100?
Thanks

Best solution: Teach your son how to use the "right" mic. Sorry, but I would not recommend the USB thing-mic. If it's "just for play", buy any mic. If it's for real recording, stick to pro hardware.
Fox

Similar Messages

Using USB Microphone With GarageBand iPad?

Hi, I have the Samson G-Track USB Microphone and have been using it with GarageBand for iPad (with a powered USB hub) and I was wondering if there is a way to enable "Monitor" so that when I speak into the microphone I can hear myself in the headphones? I have no problem recording with the microphone, I just can't hear myself when I'm recording. There are a few switches on the actual microphone that could control this or it could all be controlled from iPad itself, just looking for anyone who could help with this matter. Thanks!

I'm having the same problem trying to monitor my turntable recording via a USB phono amp connected via a USB hub to the photo connection kit.
Have you had any help with this yet?

Using USB microphone with iBook

I have an iBook G4 and GarageBand 1.1. I recently bought a MicFlex USB microphone, but I can't make it record. I have set the system preferences and I can set the record level for the USB mic there, but GarageBand automatically uses the built-in microphone for recording. How do I change this?

No worries, now you're a little less new. Enjoy --Hang

Using usb mic with logic output stops

using usb mic with logic output stops

Aggregate devices are setup in the Audio/Midi setup of OSX Utilities, (Not in Logic). It gives you a way of having for than one audio i/o device. Once you have set up your aggregated devices in Audio/Midi, when you start Logic you will need to go into Audio preferences and choose the Aggregate device.

Can i use USB headphones with my X-Fi XtremeGamer sound ca

I was wondering if there was a way to use USB headphones with my card? Also if i use my front headphone jack i only get sound out of my left speaker... is this a problem with my card, or with my headphone jack? I'd appriciate any help! Thanks

Thanks for answering about the USB! Still wondering about the front headphone jack tho

Using USB preamp with Garageband

Garageband will not recognize my microphone for some reason. I am using an M-Audio USB Preamp, with a Behringer condensor microphone. I have changed the input/output settings in both the mac settings and the garageband settings to "M-Audio Mobilepre USB." Garageband must recognize the preamp because it has it as an option in the input and output. The computer hears the microphone, because the input level bar in system preferences responds to sound. Garageband works fine with the built in mic, and the microphone volume is maxed, so I know that isn't it. Any help?

How did you figure it out?
I've been trying to plug my Gibson into Garage Band but all i get is feedback. I seemed to have followed all the same steps as you. From researching on-line right now it looks like I might have to get a pre-amp... you know anything about that?
any help would be cool.
thanks!

USB microphone with Mac mini - can it work?

I recently bought a cheap USB camera with built-in mic, and a USB headphone/microphone interface. Neither of these microphones work with my shiny new Mac mini (10.7.2). The headphone USB interface works fine, and it even includes a volume and mute - very cool indeed (Arvel HAMU02BK if you want to look it up). In the Sound Preference pane, it shows up as an input, but the meter doesn't show any response. I plug the same mic and adaptor into a G4 PowerBook (10.5.8) and it works. The camera (Buffalo BSW13K08HBK) also shows up as a mic in the Sound Preference pane, but the meter fails to respond (shows about a 60% continuous input signal, but using it with Skype test, doesn't record anything.
USB2.0 Camera:
Product ID:          0x0103
Vendor ID:          0x1e4e (Etron Technology, Inc.)
Version:          0.02
Speed:          Up to 480 Mb/sec
Manufacturer:          Etron Technology, Inc.
Location ID:          0xfa121110 / 11
Current Available (mA):          500
Current Required (mA):          100
C-Media USB Headphone Set :
Product ID:          0x000c
Vendor ID:          0x0d8c (C-MEDIA ELECTRONICS INC.)
Version:          1.00
Speed:          Up to 12 Mb/sec
Location ID:          0xfa121130 / 12
Current Available (mA):          500
Current Required (mA):          100
Camera itself seems to work nicely, though, and there seems to be enough power off the hub to make things work. Is this a bug? If I want to plug a mic into the Mac itself, can I use any of the "pink" 3-pole 3.5mm computer mics?

Followup - I'm getting:
kernel: 0        0 AppleUSBCDC: start - initDevice failed
on the Console every time one of these beasts gets connected. What to do about this?

FaceTime won't use USB microphone

I recently purchased a Samson Go Mic from Amazon. Yesterday, I received the product and connected it to my laptop, a MacBook Pro 2012 13". After changing the audio input to the microphone, I was able to use Quicktime X to record a video using the microphone. Later, when I called my dad through FaceTime, the computer no longer recognized my Go mic, and only recognized my EarPods. When I unplugged the EarPods, the audio switched to the built-in microphone of my computer, and not the Go Mic. How can I use the superior Go Mic with FaceTime?

Hello Suzanne,
Welcome to Adobe Forums.
Do you have SP1 installed for Windows 7?
Is that a laptop or Desktop ?
What is the name of the manufacturer for your USB Webcam ?
What is the name of the manufacturer for your computer ?
Make sure you have Presenter 9.0.2 update installed. (http://www.adobe.com/support/downloads/detail.jsp?ftpID=5690)
Thanks,
Vikram
Adobe Support

Can I use USB 3 with my 2.8Ghz Quad-core

I have an early 2008, 2.8 GHz Quad-Core Intel Xeon Mac Pro, can I use USB3 Devices with it?

Yes, they are all backward-compatible.
If you wnat USB-3 speed, you would need a PCIe card.

How can I use USB camera with NI cRIO 9022, please see my strange problem.

Hi,
I would like to use a USB camera with NI cRIO 9022. I used the same USB camera with NI USB 6216 DAQ device and developed a VI(within a PROJECT and outside it). So, It is working fine with NI USB 6216 device when I use the Vision Assistant Express VI and gets detected in its Initialization Window. Please see JPEG File 3 where I get NO ERROR.
I am facing a problem when I want to use it with NI cRIO 9022. What exactly I am doing in this case is:
1) Create a NEW PROJECT
2) Add Targets and Devices(NI cRIO 9022)
3) Use the Scan Interface mode
4) Create a NEW VI under the cRIO 9022 device
5) Use a Timed Loop(Synchronized with Scan Engine) for continuous Data Acquisition and Sending from the Analog I/O modules.
6) Use the Vision Assistant available through the NI Vision Acquisition 2010 Module(I get STUCK HERE! The Express VI opens the Initialization Window, but I don't see the USB camera like in JPEG File 3)
I am facing difficulties with this HOST COMPUTER, cRIO implementation differences. On my host computer I have the software packages as shown in JPEG File 1, and on my cRIO 9022 as shown in JPEG File 2.
Can someone guide me how to overcome this and get the USB camera detected when I am using NI cRIO 9022?
NOTE: If this is a problem with software mismatches on HOST and NI cRIO 9022 device, please see JPEG Files 1 and 2 for available software and Host and cRIO 9022.
Thanks.
Amar.
Attachments:
Host Computer Image or Vision Acquisition Software Installed.JPG ‏91 KB
IMAQ and dx Modules Installed on my NI cRIO 9022 hardware(No NI Vision Acquisition 2010 SP1).JPG ‏82 KB
NI Vision Acquisition Express NO Error for NI cRIO 9022.JPG ‏48 KB

When you select My Computer, you are running the program on the PC. In this case, the camera works because it is connected to the PC. The scan engine doesn't work because it needs to run on the cRIO, not the PC.
When you create the program on the cRIO, you can use the scan engine because the program is on the cRIO. You can't use the camera because it is back on the PC, and can't be found on the cRIO.
The project is a wonderful tool, but it may be making the programming seem too simple. It may not be clear to you that by moving a program to a different location (PC or cRIO), it is running in an entirely different environment on a totally different machine, even though it is just a little further down in the project. You can't easily access the hardware on one machine while running the program on the other.
So the summary is: The camera is attached to the PC. The scan engine runs on the cRIO. Never the twain shall meet.
Bruce
Bruce Ammons
Ammons Engineering

Can I use USB 6008 with LabVIEW 6.1 RT?

Hi there,
I've been using LabVIEW 6.1 RT for my applications and so far I haven't felt the need to upgrade.
However, I decided to try the USB 6008 and I'm learning the hard way that this device will only work with NI-DAQmx and apparently not with the latest NI-DAQ 7.4.2 (legacy) In fact, I can't see the device in MAX 4.1
Is there any way I can use the USB 6008 with my 6.1 RT version of LabVIEW ? or should I send the thing back to NI ?
I will appreciate your guidance on this issue.
Thanks a lot,
at

Hi at -
Allisso is right. There is no way to use the USB-6008 with LV 6.1, because neither of its drivers (DAQmx and DAQmxBase) support that version of LV. You'll have to either upgrade to a current version of LV or work with another device. I recommend contacting your sales rep at NI for help.
David Staab, CLA
Staff Systems Engineer
National Instruments

USB Microphone With Garageband & Skype?

Will I be able to record a Skype conversation using a USB Microphone? Currently, I record using my laptop's internal mic but it picks up the laptop's fan noise.

Get This skype recorder by ecamm http://ecamm.com/mac/callrecorder/ its only $14.95 and works amazing! I also use a Blue Snowflake USB mic which you can pick up on amazon for $50 and I use for both skype and my audio products I created. Then all you need is your apple earphones so you dont pick up and echo and make sure to have the mic close to your mouth so it gets better audio and no computer noise. This is what I use for my radio show and podcasts.

USB microphone with adobe flash player on chromebook

I am using fash player to record a youtube video on my samsung chromebook. I am trying to use a USB microphone to do the recording. My chromebook recognizes the USB microphone when I plug it in and I select it in my chromebooks taskbar and select it as the audio input source. When i go to record my video on flashplayer and select the microhpone in flash player icon the only option I have is default. Does this mean I cant use my USB microphone or does default refer to whatever microphone i have selected in my chromebooks preference as the audio input.

What are microphone settings?
Microphone settings allow you to select a microphone, adjust its sensitivity, and reduce the echo that may be coming from your speakers.
What happens if I do nothing?
Adobe Flash Player automatically detects any default microphone or other audio recorder on your computer, and sets microphone sensitivity to a medium value.
Note that Flash Player asks your permission before allowing an application to access your camera or microphone. See Privacy pop-up question.
What can I change here?
You can select a different microphone, adjust microphone sensitivity, and reduce echo. The settings you select here apply immediately to the active Flash application. To change the default microphone, select another microphone from the pop-up menu.
To test your microphone, speak in a normal tone of voice and watch the indicator on the left. When the indicator shows yellow, your microphone is sensitive enough for Flash Player to pick up sound. To increase or decrease your microphone's sensitivity, move the slider to the right or the left, respectively.
If you are using speakers instead of headphones, select Reduce Echo. Reducing echo has the effect of reducing the noise coming from your microphone through your speakers.
What if Flash Player doesn't find a microphone?
If Flash Player cannot locate a microphone or other audio device on your computer, the player displays the warning "No microphone detected." Read the documentation for your computer and your microphone to make sure your microphone is installed correctly.
How do I test my speakers?
Click Test Speaker in the application shown below to hear a sample sound. Adjust your speakers or headset so the sound is at a comfortable level.
How can I display this panel again?
You may want to display this panel again if, for example, you want Flash Player to use a different microphone. To display the Microphone panel:
Right-click (Windows) or Control-click (Macintosh) the application image while it is playing.
From the context menu, select Settings, and then click the Microphone tab.
I don't see the Microphone tab, so I can't display this panel.
If your computer or device doesn't support audio recording using Flash Player, you cannot select a microphone to use, and this panel doesn't appear.

How do I use a USB microphone with logic?

Logic recognizes the samson meteor microphone, but how do I get sound from it when using it for a track? Do I select an audio, software instr, or midi track? I also use an audiobox midi for my keyboard. For that, I select software instrument and then I have sound. I tried creating an aggregate device but still no sound. Thanks so much for any help possible..

The headphones port outputs audio signal from Logic. Plug the mixer into the lin-in port.
JG

How to use a microphone with my iMac?

Hi,
I recently purchased a headset to use in Ventrilo for communicating with my clients. I've plugged it into the line in and line out ports on the back. I can hear audio play just fine but when I select "Line In" as the input source in System Preferences, no sound is picked up.
From searching through Google, I'm lead to believe that the input port on the back of the iMac is expecting a stronger signal, such as the one generating by the output of most audio generating devices and the microphone's signal is too faint. Is that correct?
I see various $80+ Mac-compatible USB headsets out there but I just can't justify spending that much money on this project. If a regular headset won't work with the line in port, can anyone out there recommend a cheap headset that will work with my iMac? I'm not looking for fantastic sound, just legible voice communication.

You're correct: the line in jack needs to be fed from a mixer or hi-fi equipment: the output from a microphone is much too low. You have two easy options: one is simply to use the built-in microphone - the quality is usually quite clear and good enough for this sort of use. Or you could get a USB headset such as this one.

Using USB microphone with LE

Similar Messages

Maybe you are looking for