WAP200 Slow Web Interface
Anyone else experiencing an extremely slow web interface in the WAP200?
Even if I connect the cable side directly to my computer to eliminate our LAN as the problem, it is still painfully slow.
For example: After completing the login box when browsing to the AP, it takes 2-3 minutes to draw the first web page
Using it as an access point with only 1 SSID configured for WPA/PSK/TKIP using FW 1.0.22.
The other day, after the unit had been on for about a week, the "Setup.htm" page took about 2 hours to load into a browser.
Using the Linux "wget" command from another machine as a test showed that the webserver within the unit transmitted 1448 bytes to begin with, and then stopped for 20 minutes, and then sent about another 16K bytes of data.
Since the symptom is present on windows XP IE7 and Windows 2000 IE6, as well as a generic linux command-line command, it tells me that the WAP200 is the problem.
In each case, I tested with the computer connected direct to the WAP200 without any other networking devices between them.
Message Edited by rgagnon on 03-22-2008 04:21 PM
Similar Messages
-
3850 web interface slow to load, especially for webauth
Hi all,
Got a cat 3850 switch acting also as a wireless controller. Running 3.6.0E One thing that I've noticed is that loading the web interface to configure it is terribly slow. Also for guest authentication, it takes a long time for the web page to load. Tried IE and firefox with same results.
Thoughts?Hey thanks for the reply Rasika. Yes, I'm aware that the GUI isn't quite there yet. However for the webauth, I would expect it to be somewhat fast. The webauth file is custom, but small.
Here's the contents of the flash directory and some config:
3850#sh start | inc webauth
aaa authentication login webauth_local local
service-template webauth-global-inactive
parameter-map type webauth global
parameter-map type webauth guest_web
type webauth
custom-page login device flash:/webauth/webauth_login.html
custom-page success device flash:/webauth/webauth_success.html
custom-page failure device flash:/webauth/webauth_failure.html
custom-page login expired device flash:/webauth/webauth_expired.html
security web-auth authentication-list webauth_local
security web-auth authentication-list webauth_local
3850#sh flash:
-#- --length-- ---------date/time--------- path
2 2097152 Oct 24 2014 20:58:23.0000000000 +00:00 nvram_config
3 742912 Oct 20 2014 19:16:56.0000000000 +00:00 webauth.tar
4 4096 Oct 20 2014 19:16:58.0000000000 +00:00 webauth
5 4096 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/css
6 2098 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/css/signin.css
7 96 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/css/starter-template.css
8 4096 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/dist
9 4096 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/dist/css
10 19791 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/dist/css/bootstrap-theme.css
11 17706 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/dist/css/bootstrap-theme.min.css
12 126432 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/dist/css/bootstrap.css
13 102897 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/dist/css/bootstrap.min.css
14 4096 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/dist/fonts
15 20290 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/dist/fonts/glyphicons-halflings-regular.eot
16 62850 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/dist/fonts/glyphicons-halflings-regular.svg
17 41236 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/dist/fonts/glyphicons-halflings-regular.ttf
18 23292 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/dist/fonts/glyphicons-halflings-regular.woff
19 4096 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/dist/js
20 58327 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/dist/js/bootstrap.js
21 27748 Oct 20 2014 19:16:57.0000000000 +00:00 webauth/dist/js/bootstrap.min.js
22 4096 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/img
23 98601 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/img/web_auth_background_blur.jpg
24 174 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/img/web_auth_close.png
25 30325 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/img/web_auth_onloklogo.jpg
26 5768 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/img/web_auth_onlok_logo.png
27 251 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/img/web_auth_open.png
28 4096 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js
29 3861 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js/affix.js
30 2582 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js/alert.js
31 3048 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js/button.js
32 6445 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js/carousel.js
33 5228 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js/collapse.js
34 4484 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js/dropdown.js
35 2636 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js/html5shiv.min.js
36 694 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js/ie10-viewport-bug-workaround.js
37 6975 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js/modal.js
38 3488 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js/popover.js
39 4377 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js/respond.min.js
40 4622 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js/scrollspy.js
41 3413 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js/tab.js
42 11908 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js/tooltip.js
43 1964 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/js/transition.js
44 1334 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/webauth_expired.html
45 1618 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/webauth_failure.html
46 1932 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/webauth_login.html
47 1641 Oct 20 2014 19:16:58.0000000000 +00:00 webauth/webauth_success.html
48 10445 Oct 28 2014 19:03:11.0000000000 +00:00 wnweb.tgz
49 82672260 Oct 19 2014 06:29:54.0000000000 +00:00 cat3k_caa-base.SPA.03.06.00E.pkg
50 6601404 Oct 19 2014 06:29:54.0000000000 +00:00 cat3k_caa-drivers.SPA.03.06.00E.pkg
51 1235 Oct 19 2014 06:29:59.0000000000 +00:00 packages.conf
52 1156 Oct 19 2014 06:43:36.0000000000 +00:00 vlan.dat
53 33747948 Oct 19 2014 06:29:54.0000000000 +00:00 cat3k_caa-infra.SPA.03.06.00E.pkg
54 4096 Dec 27 2013 03:17:04.0000000000 +00:00 mnt
55 4096 Dec 27 2013 03:17:04.0000000000 +00:00 mnt/images
56 4096 Dec 27 2013 03:17:09.0000000000 +00:00 mnt/images/ap.bak
57 40 Dec 05 2013 18:36:37.0000000000 +00:00 mnt/images/ap.bak/ap1g2.md5
58 11612160 Dec 05 2013 18:36:37.0000000000 +00:00 mnt/images/ap.bak/ap1g2
59 40 Dec 05 2013 18:36:37.0000000000 +00:00 mnt/images/ap.bak/ap3g1.md5
60 10475520 Dec 05 2013 18:36:38.0000000000 +00:00 mnt/images/ap.bak/ap3g1
61 40 Dec 05 2013 18:36:37.0000000000 +00:00 mnt/images/ap.bak/ap3g2.md5
62 13670400 Dec 05 2013 18:36:37.0000000000 +00:00 mnt/images/ap.bak/ap3g2
63 40 Dec 05 2013 18:36:37.0000000000 +00:00 mnt/images/ap.bak/c1140.md5
64 10321920 Dec 05 2013 18:36:37.0000000000 +00:00 mnt/images/ap.bak/c1140
65 11 Dec 05 2013 18:36:37.0000000000 +00:00 mnt/images/ap.bak/version.info
66 42769724 Oct 19 2014 06:29:54.0000000000 +00:00 cat3k_caa-iosd-universalk9.SPA.152-2.E.pkg
67 4096 Oct 19 2014 06:42:45.0000000000 +00:00 dc_profile_dir
68 169223 Oct 19 2014 06:42:45.0000000000 +00:00 dc_profile_dir/dc_default_profiles.txt
69 169223 Oct 19 2014 06:42:45.0000000000 +00:00 dc_profile_dir/dc_default_profiles.txt.bkp
70 25711500 Oct 19 2014 06:29:54.0000000000 +00:00 cat3k_caa-platform.SPA.03.06.00E.pkg
71 98462528 Oct 19 2014 06:29:55.0000000000 +00:00 cat3k_caa-wcm.SPA.10.2.102.0.pkg
1196404736 bytes available (343171072 bytes used) -
CUCM 8.6, UnityCon 8.6 and Presence 8.6 on ESXi 5 C200 web interface lag
When trying to bring up any web interfaces or even vSphere it is so slow as to also not be usable.. Brand new install on 2 C200 UCS servers.
Before you ask. Yes LRO is disabled according to Cisco's instructions and confirmed. I have CUCM and Presence on one NIC and Unity Con by itself on the other NIC.
Restarting Tomcat does nothing to help..
Even restarting the entire cluster does nothing to help..
All 6 machine Pubs and Subs of each application type were created in ESXi 5 with .ova files and unchanged.
Sent from Cisco Technical Support iPad App
Update!!!!
All lag stops if I turn off the presence subscriber!?!?!?!?!?
What the heck..Hi mate,
What does RTMT or CLI show about CPU memory and process usage?
Probably should not affect GUI but is correct VMware tools installed as well?
Once you verify apps check what VMware says about performance.
What size ovas did you use? Are you over subscribed?
How long have you waited? Is it just cups performing sync and hogging resources for example
Cheers,
Tim
Sent from Cisco Technical Support iPad App -
NMH300 Issues : Indexing, recent files, web interface ...
Hi,
I am presently having A LOT of problems with my NMH.
I tried to reboot, different drives, different settings with drives (raid, linear ...), different firewalls, different IP settings, different route settings, cat5 and cat6 ethernet cables ... And IT IS NOT WORKING !!!
At first, i just tried to use the NMH as a Media Server for my music and video files.
I was trying to stream content with my playstation3 (videos and music files).
It was working well for videos but the music folder was a complete mess (the web interface shows some unreallistic ID3 information) and some files don't appear int the web interface.
(I formerly was using PS3 Media Server on my laptop to share content mith my PS3 and the music folder was NOT a mess, all my files were ok and playing good).
I have to tell that my ID3 tag are quite allright (except some personal files not tagged).
At that time, the main problem was a really slow and unstable access so streaming music was not really good.
I looked for a solution and about 3 months later, I found something out ...
The problem that poped out from forum searchs was a maximum of files allowed by the NMH.
I had to many music files so the indexing was never ending, the acces was very slow, copying a 100Mb video file could take more than 30 mins ...
So I just made a backup of my datas, formatted my Seagate 500Gb drive and then just copied some files (not a lot) in each music, videos and pictures folders. At that time, it was pretty ok (except that I had some issues trying to connect to the web interface but anyway, the ps3 was accessing files quite good)
I was using around 50 files in each media folder.
Then I plugged in my second drive (Western Digital 640Gb) to use it in linear mode (btw, this is what I would like to have in a final time : about 1Tb in linear mode).
At that time, still working quite good.
I added some videos files (about 100Gb), my pics collection (about 15Gb) and some more music files. (8Gb in less than 7000 files in order to keep indexing working good).
And here I am now, with my MediaHub half loaded (still have more than 65000 music files waiting for a solution !!!), trying to browse with my PS3:
- videos look good, browsing and streaming both ok
- pictures look good too, I can browse the folders and see my pics without a problem
- music ... well, I cannot browse the folder anymore (in ps3 tree menu "folder" does not appear anymore, only "artist", "album", "playlists" ...) which is really annoying for me (I use a a lot of sample libraries and each have their own "artist" and "album")
But anyway, I decided to give a look at the web interface and I noticed that the recent files that were showing up were files that were not present anymore on the disc !!! It seemed like the only recent files showing were files I added 2 months ago.
I was looking at the "recent files" I was using when I first set up my NMH for the first time ...
By now, I've read some threads about this problem but there no solution.
Some helped resolving the "indexing" issue. I tried to reboot several times, formatted the Seagate then the Western Digital drive to see a difference but nothing.
So my questions:
Is there a way to have a full working NMH concerning music and ID3 information ?
Is there a way to completely clear the NMH music information database to have it ready to be re-filled ?
Did someone managed to have a stable installation ?
And finally, can you browse your music folder and see the original tree (as you see it in windows) ?
Thanks a lot for your help and information.Well ... I tried ... It failed !!!
The TwonkyMedia settings page currently shows :
Content
Music Tracks : 3830
Photos : 251
Videos : 465
Radios stations : 0
My clients are all set up as they should be
(except my isp box which shows "generic media receiver")
I tried different options to see if there were any differences (auto-share media with new clients on/off, ftp enabled/disabled, iTunes library service on/off ...) but there is no way I can see my music thru the web interface.
As a consequence, I cannot reach my music from the outside. (over the web for example).
I even tried to use a blackberry, an iPhone, a HTC Desire and an iPod touch to see if I could access my files thanks to the twonkymedia ( h t t p : / / [ my ip ] : 9000 ) ... The twonkymedia page shows up (I can't access any file (music, video nor photos) because of a gateway timeout.
I just don't get what's wrong with my NMH but I really am fed up with it ...
To sum up, thanks to your links Wilkins377 :
- I now can complete the scanning without any problem.
- My music folder is now browseable by folder (as shown in windows) thru the PS3
- I now can turn off the NMH by pressing the power button during 5 seconds (it used to restart)
But ... (again) ... :
- Hardrives won't stop spinning and both drives are very very hoooooot (can't touch them !!!)
- As a result, the NMH is really noisy and noise isn't stoppipng at all (24/7).
- No recent music files and no music files at all in the NMH web interface.
Please help me !!! Anyone ... I'm desperate ...
PS: I didn't upgrade to 3.8.15 so I still am using the 3.8.14 firmware. Everything was ok at first (I mean when I first installed my NMH) before I tried the 3.8.15 so I'd prefer not to upgrade as I am certain that the NMH CAN work well on my network with the 3.8.14 firmware. -
Really Slow web surfing through ZBF with IOS Content filter
Edited: attached partial output of "sh policy-map type inspect zone-pair urlfilter"
Hey, all
We have a 1921 router with IOS Content filter subscribsion and it is also configured as ZBF running latest IOS v15.1. End-user keep complaining about slow web surfing. I connected to network and tested myself and found intermittent surfing experience.
For example, access to www.ibm.com or www.cnn.com hangs 7 times of 10 attempts and maybe only loads reasonablly quick in 1-2 time of the 3. This also affects the speed of download from websites.
I have the case openned with Cisco TAC and CCIE checked my configure but nothing caught his eyes...
I decide to post the issue here in case we both missed something:
Current configuration : 18977 bytes
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname abc_1921
boot-start-marker
boot system flash:/c1900-universalk9-mz.SPA.151-4.M4.bin
boot-end-marker
aaa new-model
aaa authentication login default local
aaa authentication login NONE_LOGIN none
aaa authorization exec default local
aaa session-id common
clock timezone AST -4 0
clock summer-time ADT recurring 3 Sun Mar 2:00 2 Sun Nov 2:00
no ipv6 cef
ip source-route
ip auth-proxy max-login-attempts 5
ip admission max-login-attempts 5
ip cef
ip dhcp excluded-address 192.168.1.1 192.168.1.9
ip dhcp excluded-address 192.168.1.111 192.168.1.254
ip dhcp pool DHCPPOOL
import all
network 192.168.1.0 255.255.255.0
domain-name abc.local
dns-server 192.168.10.200 192.168.10.202
netbios-name-server 4.2.2.4
default-router 192.168.1.150
option 202 ip 192.168.1.218
lease 8
ip domain name abc.locol
ip name-server 8.8.8.8
ip name-server 4.2.2.2
ip port-map user-port-1 port tcp 5080
ip port-map user-port-2 port tcp 3389
ip inspect log drop-pkt
multilink bundle-name authenticated
parameter-map type inspect global
log dropped-packets enable
parameter-map type urlfpolicy trend cprepdenyregex0
allow-mode on
block-page message "The website you have accessed is blocked as per corporate policy"
parameter-map type urlf-glob cpaddbnwlocparapermit2
pattern www.alc.ca
pattern www.espn.com
pattern www.bestcarriers.com
pattern www.gulfpacificseafood.com
pattern www.lafermeblackriver.ca
pattern 69.156.240.29
pattern www.tyson.com
pattern www.citybrewery.com
pattern www.canadianbusinessdirectory.ca
pattern www.homedepot.ca
pattern ai.fmcsa.dot.gov
pattern www.mtq.gouv.qc.ca
pattern licenseinfo.oregon.gov
pattern www.summitfoods.com
pattern www.marine-atlantic.ca
pattern www.larway.com
pattern www.rtlmotor.ca
pattern *.abc.com
pattern *.kijiji.ca
pattern *.linkedin.com
pattern *.skype.com
pattern toronto.bluejays.mlb.com
pattern *.gstatic.com
parameter-map type urlf-glob cpaddbnwlocparadeny3
pattern www.facebook.com
pattern www.radiofreecolorado.net
pattern facebook.com
pattern worldofwarcraft.com
pattern identityunknown.net
pattern static.break.com
pattern lyris01.media.com
pattern www.saltofreight.com
pattern reality-check.com
pattern reality-check.ca
parameter-map type ooo global
tcp reassembly timeout 5
tcp reassembly queue length 128
tcp reassembly memory limit 8192
parameter-map type trend-global global-param-map
cache-size maximum-memory 5000
crypto pki token default removal timeout 0
crypto pki trustpoint Equifax_Secure_CA
revocation-check none
crypto pki trustpoint NetworkSolutions_CA
revocation-check none
crypto pki trustpoint trps1_server
revocation-check none
crypto pki trustpoint TP-self-signed-3538579429
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3538579429
revocation-check none
rsakeypair TP-self-signed-3538579429
!! CERTIFICATE OMITED !!
redundancy
ip ssh version 2
class-map type inspect match-any INCOMING_VPN_TRAFFIC_MAP
match access-group name REMOTE_SITE_SUBNET
class-map type inspect match-all PPTP_GRE_INSPECT_MAP
match access-group name ALLOW_GRE
class-map type inspect match-all INSPECT_SKINNY_MAP
match protocol skinny
class-map type inspect match-all INVALID_SOURCE_MAP
match access-group name INVALID_SOURCE
class-map type inspect match-all ALLOW_PING_MAP
match protocol icmp
class-map type urlfilter match-any cpaddbnwlocclasspermit2
match server-domain urlf-glob cpaddbnwlocparapermit2
class-map type urlfilter match-any cpaddbnwlocclassdeny3
match server-domain urlf-glob cpaddbnwlocparadeny3
class-map type urlfilter trend match-any cpcatdenyclass2
class-map type inspect match-all cpinspectclass1
match protocol http
class-map type inspect match-any CUSTOMIZED_PROTOCOL_216
match protocol citriximaclient
match protocol ica
match protocol http
match protocol https
class-map type inspect match-any INSPECT_SIP_MAP
match protocol sip
class-map type urlfilter trend match-any cptrendclasscatdeny1
match url category Abortion
match url category Activist-Groups
match url category Adult-Mature-Content
match url category Chat-Instant-Messaging
match url category Cult-Occult
match url category Cultural-Institutions
match url category Gambling
match url category Games
match url category Illegal-Drugs
match url category Illegal-Questionable
match url category Internet-Radio-and-TV
match url category Joke-Programs
match url category Military
match url category Nudity
match url category Pay-to-surf
match url category Peer-to-Peer
match url category Personals-Dating
match url category Pornography
match url category Proxy-Avoidance
match url category Sex-education
match url category Social-Networking
match url category Spam
match url category Tasteless
match url category Violence-hate-racism
class-map type inspect match-any INSPECT_PROTOCOLS_MAP
match protocol pptp
match protocol dns
match protocol ftp
match protocol https
match protocol imap
match protocol pop3
match protocol netshow
match protocol shell
match protocol realmedia
match protocol rtsp
match protocol smtp
match protocol sql-net
match protocol streamworks
match protocol tftp
match protocol vdolive
match protocol tcp
match protocol udp
match protocol icmp
class-map type urlfilter trend match-any cptrendclassrepdeny1
match url reputation ADWARE
match url reputation DIALER
match url reputation DISEASE-VECTOR
match url reputation HACKING
match url reputation PASSWORD-CRACKING-APPLICATIONS
match url reputation PHISHING
match url reputation POTENTIALLY-MALICIOUS-SOFTWARE
match url reputation SPYWARE
match url reputation VIRUS-ACCOMPLICE
class-map type inspect match-all CUSTOMIZED_NAT_MAP_1
match access-group name CUSTOMIZED_NAT_1
match protocol user-port-1
class-map type inspect match-all CUSTOMIZED_NAT_MAP_2
match access-group name CUSTOMIZED_NAT_2
match protocol user-port-2
class-map type inspect match-any INSPECT_H323_MAP
match protocol h323
match protocol h323-nxg
match protocol h323-annexe
class-map type inspect match-all INSPECT_H225_MAP
match protocol h225ras
class-map type inspect match-all CUSTOMIZED_216_MAP
match class-map CUSTOMIZED_PROTOCOL_216
match access-group name CUSTOMIZED_NAT_216
policy-map type inspect OUT-IN-INSPECT-POLICY
class type inspect INCOMING_VPN_TRAFFIC_MAP
inspect
class type inspect PPTP_GRE_INSPECT_MAP
pass
class type inspect CUSTOMIZED_NAT_MAP_1
inspect
class type inspect CUSTOMIZED_NAT_MAP_2
inspect
class type inspect CUSTOMIZED_216_MAP
inspect
class class-default
drop
policy-map type inspect urlfilter cppolicymap-1
description Default abc Policy Filter
parameter type urlfpolicy trend cprepdenyregex0
class type urlfilter cpaddbnwlocclasspermit2
allow
class type urlfilter cpaddbnwlocclassdeny3
reset
log
class type urlfilter trend cptrendclasscatdeny1
reset
log
class type urlfilter trend cptrendclassrepdeny1
reset
log
policy-map type inspect IN-OUT-INSPECT-POLICY
class type inspect cpinspectclass1
inspect
service-policy urlfilter cppolicymap-1
class type inspect INSPECT_PROTOCOLS_MAP
inspect
class type inspect INVALID_SOURCE_MAP
inspect
class type inspect INSPECT_SIP_MAP
inspect
class type inspect ALLOW_PING_MAP
inspect
class type inspect INSPECT_SKINNY_MAP
inspect
class type inspect INSPECT_H225_MAP
inspect
class type inspect INSPECT_H323_MAP
inspect
class class-default
drop
zone security inside
description INTERNAL_NETWORK
zone security outside
description PUBLIC_NETWORK
zone-pair security INSIDE_2_OUTSIDE source inside destination outside
service-policy type inspect IN-OUT-INSPECT-POLICY
zone-pair security OUTSIDE_2_INSIDE source outside destination inside
service-policy type inspect OUT-IN-INSPECT-POLICY
crypto isakmp policy 10
encr 3des
authentication pre-share
group 2
crypto isakmp key password address 11.22.3.1
crypto ipsec security-association lifetime seconds 28800
crypto ipsec transform-set TunnelToCold esp-3des
crypto map TunnelsToRemoteSites 10 ipsec-isakmp
set peer 11.22.3.1
set transform-set TunnelToCold
match address TUNNEL_TRAFFIC2Cold
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
description OUTSIDE_INTERFACE
ip address 1.1.1.186 255.255.255.248
ip nat outside
ip virtual-reassembly in
zone-member security outside
duplex full
speed 1000
crypto map TunnelsToRemoteSites
crypto ipsec df-bit clear
interface GigabitEthernet0/1
description INSIDE_INTERFACE
ip address 192.168.1.150 255.255.255.0
ip nat inside
ip virtual-reassembly in
zone-member security inside
duplex full
speed 1000
ip forward-protocol nd
ip http server
ip http access-class 10
ip http authentication local
ip http secure-server
ip nat inside source static tcp 192.168.1.217 5080 interface GigabitEthernet0/0 5080
ip nat inside source route-map NAT_MAP interface GigabitEthernet0/0 overload
ip nat inside source static tcp 192.168.1.216 80 1.1.1.187 80 extendable
ip nat inside source static tcp 192.168.1.216 443 1.1.1.187 443 extendable
ip nat inside source static tcp 192.168.1.216 1494 1.1.1.187 1494 extendable
ip nat inside source static tcp 192.168.1.216 2598 1.1.1.187 2598 extendable
ip nat inside source static tcp 192.168.1.213 3389 1.1.1.187 3390 extendable
ip nat inside source static tcp 192.168.1.216 5080 1.1.1.187 5080 extendable
ip route 0.0.0.0 0.0.0.0 1.1.1.185
ip access-list standard LINE_ACCESS_CONTROL
permit 192.168.1.0 0.0.0.255
ip access-list extended ALLOW_ESP_AH
permit esp any any
permit ahp any any
ip access-list extended ALLOW_GRE
permit gre any any
ip access-list extended CUSTOMIZED_NAT_1
permit ip any host 192.168.1.217
permit ip any host 192.168.1.216
ip access-list extended CUSTOMIZED_NAT_2
permit ip any host 192.168.1.216
permit ip any host 192.168.1.212
permit ip any host 192.168.1.213
ip access-list extended CUSTOMIZED_NAT_216
permit ip any host 192.168.1.216
ip access-list extended INVALID_SOURCE
permit ip host 255.255.255.255 any
permit ip 127.0.0.0 0.255.255.255 any
ip access-list extended NAT_RULES
deny ip 192.168.1.0 0.0.0.255 192.168.2.0 0.0.0.255
deny ip 192.168.1.0 0.0.0.255 192.168.3.0 0.0.0.255
deny ip 192.168.1.0 0.0.0.255 192.168.4.0 0.0.0.255
deny ip 192.168.1.0 0.0.0.255 192.168.5.0 0.0.0.255
deny ip 192.168.1.0 0.0.0.255 192.168.6.0 0.0.0.255
deny ip 192.168.1.0 0.0.0.255 192.168.7.0 0.0.0.255
deny ip 192.168.1.0 0.0.0.255 192.168.8.0 0.0.0.255
deny ip 192.168.1.0 0.0.0.255 192.168.9.0 0.0.0.255
deny ip 192.168.1.0 0.0.0.255 192.168.10.0 0.0.0.255
permit ip 192.168.1.0 0.0.0.255 any
ip access-list extended REMOTE_SITE_SUBNET
permit ip 192.168.2.0 0.0.0.255 192.168.1.0 0.0.0.255
permit ip 192.168.3.0 0.0.0.255 192.168.1.0 0.0.0.255
permit ip 192.168.4.0 0.0.0.255 192.168.1.0 0.0.0.255
permit ip 192.168.5.0 0.0.0.255 192.168.1.0 0.0.0.255
permit ip 192.168.6.0 0.0.0.255 192.168.1.0 0.0.0.255
permit ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255
permit ip 192.168.8.0 0.0.0.255 192.168.1.0 0.0.0.255
permit ip 192.168.9.0 0.0.0.255 192.168.1.0 0.0.0.255
permit ip 192.168.10.0 0.0.0.255 192.168.1.0 0.0.0.255
ip access-list extended TUNNEL_TRAFFIC2ABM
permit ip 192.168.1.0 0.0.0.255 192.168.10.0 0.0.0.255
ip access-list extended TUNNEL_TRAFFIC2Bridgewater
permit ip 192.168.1.0 0.0.0.255 192.168.8.0 0.0.0.255
ip access-list extended TUNNEL_TRAFFIC2ColdbrookDispatch
permit ip 192.168.1.0 0.0.0.255 192.168.2.0 0.0.0.255
ip access-list extended TUNNEL_TRAFFIC2ColdbrookETL
permit ip 192.168.1.0 0.0.0.255 192.168.7.0 0.0.0.255
ip access-list extended TUNNEL_TRAFFIC2ColdbrookTrailershop
permit ip 192.168.1.0 0.0.0.255 192.168.3.0 0.0.0.255
ip access-list extended TUNNEL_TRAFFIC2Moncton
permit ip 192.168.1.0 0.0.0.255 192.168.6.0 0.0.0.255
ip access-list extended TUNNEL_TRAFFIC2MountPearl
permit ip 192.168.1.0 0.0.0.255 192.168.4.0 0.0.0.255
ip access-list extended TUNNEL_TRAFFIC2Ontoria
permit ip 192.168.1.0 0.0.0.255 192.168.5.0 0.0.0.255
ip access-list extended WEB_TRAFFIC
permit tcp 192.168.1.0 0.0.0.255 any eq www
access-list 10 permit 192.168.1.0 0.0.0.255
route-map NAT_MAP permit 10
match ip address NAT_RULES
snmp-server community 1publicl RO
control-plane
line con 0
logging synchronous
login authentication NONE_LOGIN
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
access-class LINE_ACCESS_CONTROL in
exec-timeout 30 0
logging synchronous
transport input all
scheduler allocate 20000 1000
ntp server 0.ca.pool.ntp.org prefer
ntp server 1.ca.pool.ntp.org
endHi,
I know this is for a different platform but have a look at this link:
https://supportforums.cisco.com/thread/2089462
Read through it to get some idea of the similarity, but in particular note the last entry almost a year after the original post.
I too am having trouble with http inspection, if I do layers 3 & 4 inspection there is no issue whatsoever, but as soon as I enable layer 7 inspection then I have intermittent browsing issues.
The easy solution here is to leave it at layers 3 & 4, which doesn't give you the flixibility to do cool things like blocking websites, IM, regex expression matching etc... but in my opinion I just don't think these routers can handle it.
It appears to be a hit and miss affair, and going on the last post from the above link, you might be better off in having the unit replaced under warranty.
The alternative is wasting a lot of time and effort and impacting your users to get something up and running that in the end is so flaky that you have no confidence in the solution and you are then in a situation where ALL future issues users are facing MIGHT be because of this layer 7 inspection bug/hardware issue etc?
I would recommend you use the router as a frontline firewall with inbound/outbound acl's (no inspection), and then invest a few $ in getting an ASA dedicated firewall (but that's just me ) -
Problems access to a web application (Web Interface or Web report)
Hi,
We found problems with the access to web application. Some users have problems with direct links to the web applications(Web Interface or Web reporting), when they click on the link an error message appears, the message displays the following text:
"Cannot open file Bex?sap-language=ENbsplanguge=ENcmd=idoc_TE.."
Clicking in details the message is "No Access to specified file"
For this users the access to excel reporting is correct, the message appears when they click on the direct web links through the browser or directly in BW system, but if they type the URL they can access. Other users can use the direct web link without problems.
I highly appreciate any help or idea about how to solve this issue.
Thanks in advance.HI,
please ask to your basis that check the language of every single user on su01 tx.
This is the problem i think.
Natalia. -
Unable to capture trace, when user logs in throuigh Web Interface
The Trace shows 'No Records Found', when user logs in through Web Interface of CRM. But there is Trace found, when the same user logs in through logon pad and carries out normal actvities.
sufficient auth. is provided.
Is there any setting in ST01, through which i can get trace , when user logs in through Web Interface
RegardsST10 traces 1 instance only.
Your CRM web interface could use another instance than your backend. Go to transaction SM21, choose the appropriate server and run ST10 again.
Succes!
Kind regards,
Lodewijk Borsboom -
LIST OF VALUES not Populating in BPS WEB INTERFACE ( LAYOUTS )
Hi BI Guru's
I have created a WEB interface for BPS in BI ( version 7.0) . But when i execute this in internet explorer, I do not get the LIST OF VALUES for Material.
When I click on "input help" the system open a new window for "Value selection". When I specify the material code, it gives me blank LIST OF VALUES.
But it is working for other fields like Customer, UOM in the same layout.
Please suggest some solution.
Thanks,
Nilesh Labdehi,
Thanks for the reply.
Master data is avaliable for the Material Code. The problem is in Internet Explorer and not in SAP GUI .
If i run Planning folder for the same layou in SAP GUI it is working fine. -
ASA 5505 configured for WebVPN connecting to Citrix Web Interface
ASA 5505 configured for WebVPN connecting to Citrix Web Interface.
i have a ASA 5505 that I am attempting to configure for WebVPN with passthrough into Web Interface . The user authenticates into WebVPN OK and gets the option to click on the Citrix Link (which is i add bookmark citrix server http:// 172.30.40.5.) i enter the citrix and then for example i want to open to outlook it can not open. (when i want to open some application no application is open)).there is no alarm at asa. how i solve this issue?
thanks.Teymur,
Can you confim that after disabling the ssl/tls on the Citrix server (secure connectivity) that you are getting exactly the same error. It is possible that it is generating a different error.
The bug where we have see the existing error was CSCtf06303 but that has been fixed in 8.4.1. Can you confirm the exact version of code you are running on the ASA.
If you have confirmed the above two notes it may be adventageous to open a TAC case as we may need to do some live additional troubleshooting.
Thanks
-Jay -
Distortion in Save For Web interface
I am still having problems with my Save For Web interface. Attached is a screen where you can see that with just the Optimized view showing (in this case 72%), the picture looks as expected. But if I go to 2-up or 4-up views, the 2nd image (which was the 72% Optimized) is now all pixelated as if it were a GIF.
OMG! How many years have I been using this program and I have never noticed this until now?!?
Sorry for the brain fart and thanks for pointing that out!!!
I am really having a good laugh at myself about this one!
Jules -
Cisco AP 1131AG Web Interface Problem
Hello,
I purchased two Cisco access points (model AIR-AP1131AG-A-K9) from a seller on eBay. The Access Points power up fine and are able to get an IP address (I can see the AP's MAC address on my router), but it won't let me connect to the web interface to manage it. I have tried using different browsers, but they all say something along the lines of "The page could not be found" when I enter the IP address into my browser. No login screen, no nothing: just a time-out error.
When the Access Points are powered on, the Ethernet and Radio lights start out green, but then the Ethernet light stays green and the radio light flashes amber and the two alternate being lit. The status light on the outside of the Access Point goes from green to orange to red and back again, looping infinitely.
Any ideas what could be wrong? Thanks for any and all help in advance! (Please let me know if you need more information; I don't ahve the AP's with me, but I will be home in a few hours and can respond then.)do a show cdp neighbor detail on the port the AP is connected to. Take a look at the software that is running, IOS will show k9w7, and lightweight will show k9w8.
if it''s k9w8, you'll need to convert them back to IOS
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918
HTH,
Steve
Please remember to rate useful posts, and mark questions as answered -
Displaying a BW query in web interface
Hello People ,
I am trying to see a BW query in a web interface . I will tell you how am I doing it . I run the transaction RRMX which opens an excel sheet and gives me a tol bar from which I open a query . Then I choose info areas from the next window and it shows me a tree structure with two nodes
1) Financial
2) Industry sectors
I expand industry sectors > retail > staff works
This takes me to two nodes
1) operational
2) sales infocube
I expand sales infocube and this takes me to a couple of nodes
1) Key business driver
2) Manager forcasted sales
3) Productivity data source
4) .
5) .etc
I select key business driver and choose the CHANGE icon from the toolbar . This opens the query designer . There I have an icon in the toolbar which says display quey on web . I click that and it attempts to display the query in internet explorer .
Now the problem is the the message that appears on the browser is
Warning sign : variable OFPER for characterstic fiscal year/period has been converted to required entry .
Error sign : Error when generating data provider .
Now my question is what does this message mean ?Does this mean that the required content that I am trying to access has not been activated or there is some configurational issue ?
Regards
Deepak SinghHi Deepak,
It means that there is a selection screen for Fiscal period in which you have to enter the Fiscal Period. Only for the Fiscal period for which you entered the data would be displayed.
But the best way to create teh web report is to goto Web Application Designer -> Drag and drop the "Table" webitem on the right hand side -> Assign the Query to the web item. Now execute it in browser from the Web Application designer. Copy the link and use it whenver you want it.
Bye
Dinesh -
BPS_WB-Can i add a query to a Web interface tabpage?
Dear experts,
In a BPS web interface application, i have already a tab page which allows users to input their data. Now i would like to add a second tabpage which allows to display the existing data.
Is that possible to link a BEX query to a Tabpage BPS web interface application? I would like that the query is launched and the result is displayed each time an user click on this tabpage.
Thanks in advance.Include your query in a web template and follow the approach given in the link http://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/a861d590-0201-0010-248a-fc70d8d29f26
Edited by: Deepti Maru on Nov 30, 2010 10:24 AM -
Executing the planning function while opening the web interface
hello all,
I have created a planning area based on multiprovider.This multiprovider is based on two transactional cube ie,COPA cube and Cost Center cube.
This planning area is meant for enabling integrated planning.One plans in COPA cube and other plans in Cost Center cube the income statement gets planned based on this two.
I selected planning items in multiprovider layout to display the income statement.The layout is as follows:
<b>PlanningItem</b> <b>Amount</b>
Net Sales<b>:</b> 9.000,00 INR (This comes from COPA)
Sales Overheads<b>:</b> 200,00 INR (This comes from Cost Center)
Depreciation<b>:</b> 200,00 INR (This comes from Cost Center)
Other Expenses<b>:</b> 300,00 INR (This comes from Cost Center)
EBIT<b>:</b> 0,00 INR
Interest Income<b>:</b> 0,00 INR
Interest Expense<b>:</b> 0,00 INR
Operating Income<b>:</b> 0,00 INR
Taxes<b>:</b> 0,00 INR
Now EBIT planning item is to be calculated from the planning items as follows:
EBIT = Net Sales-Sales Overheads-Depriciation-Other Expenses
For this i have created a planning function which calculates EBIT.This function works properly,there are no issues in it.
My problem is that i want this function to be executed as soon as i open the web interface for my planning application and the result should be as follows:
<b>PlanningItem</b> <b>Amount</b>
Net Sales<b>:</b> 9.000,00 INR (This comes from COPA)
Sales Overheads<b>:</b> 200,00 INR (This comes from Cost Center)
Depreciation<b>:</b> 200,00 INR (This comes from Cost Center)
Other Expenses<b>:</b> 300,00 INR (This comes from Cost Center)
EBIT<b>:</b> 8.300,00 INR
Interest Income<b>:</b> 0,00 INR
Interest Expense<b>:</b> 0,00 INR
Operating Income<b>:</b> 0,00 INR
Taxes<b>:</b> 0,00 INR
Can anybody suggest how to go about this problem?
Thanks in advance.
regards,
YogeshHi Yogesh,
as far as i know, there is no standard functionality for that purpose, but there are workaround for it.
1. Modify the BSP Application.
Go to SE80 --> Repository Browser --> BSP Application --> your WI name --> page with flow logic --> double click on page1.htm --> Event handler tabstrip --> on the drop down selection press F1 --> add a function module that call you BPS function in specific event (e.g: OnInitialization).
2. Use WI-Exit Class / WI-Extention (ABAP OO).
Here you need to create sub class from Class: CL_UPWB_BSP_APPL, and assign the class to your WI. You can then add a function module that call you BPS function in method:
2.1. Load --> performed only once on intial execution of WI.
2.2. Initialisation --> called once for each server response.
2.3. Dispatch --> called at each action and also for each WI component.
You can see further information in SAP how to paper:
How to Validate manual input in WEB planning application, New BPS-Features delivered with SAP BW 3.5, etc.
You can call your BPS function with BPS API FM (See F.Group: UPC_API)
But there is also more easier way to realize your ebit calculation. If you define your EBIT calc. manually in layout (define with manually defined Lead column). With this way, You will always get your EBIT analog with inputed values.
Then you add your EBIT calc.function to Layout Component in WI in property: 'Function After Data Change'.
Best Regards,
Suan Liono -
P&L report (using web interface builder)???
Hi all,
Can someone explain BPS report concept for me?
For example,
In my P&L report, I will have fixed cost, variable cost, and revenue...etc.
I created fixed cost layout, variable cost layout, and revenue layout...etc.
My question is <b>how those layouts generate a P&L report on the web interface??? If</b> I enter planning data in the fixed cost layout and the values should be in the P&L report as well. <b>How can I create P&L report in the web interface after I finished all layouts???</b>Thank you for sharing
J.Hi
You should create a BEX Web Query and integrate it in the upper level of WEB Layout.
Check this link for a step by step guide about this topic
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/library/how-to%20guides%20-%20rig%20official/bi/nw04/how%20to%20integrate%20bex%20web%20applications%20into%20bps%20web%20interfaces.doc
Ciao
Andr
Maybe you are looking for
-
An error on purchasing an app in Applestore
I have recently bought an iPad for my daughter so quite new to using apple products. I have tried to purchase an app through the Apple store but it does seem to have worked successfully. The app appears in my purchases but nowhere on my home pages. I
-
How to clear invalid item value?
Hi, All. I have two items: selectOneChoice and inputComboboxListOfValues. The second item list of values depends on the first item selected value. When the value of the first item is changed, the second item should be reset. I do this by calling se
-
hi i need help on how to install properly symbian belle on my c7... the update was availbale on nokia suite 3.3(latest) (1)the 300mb download was a success, (2) the backing up was a success, (3) now i have a problem with the 3rd step which was the in
-
BURSTING - separate output file to individual
I have a report that generates a batch of documents, in one request each separated by one ID. How can I have this file split to have one document for each Page, instead of one document? The example below shows my XML Data Output and how it hold all t
-
Hello Experts I'am facing a peculiar problem pertaining to Infoset query ( Tran SQ01,SQ02, SQ03) . The requirement is to create a query based on table GLPCA and CATSDB. I've created the query as required, However when i execute the same the output is