Wifi ad-hoc. WPA doesn't working.

Hi
I want to create encrypted ad-hoc network with wpa_supplicant and i have a trouble. Network has been created, but without any encryption.
Here is my config:
ctrl_interface=/var/run/wpa_supplicant
ctrl_interface_group=wheel
ap_scan=2
network={
ssid="Ad-Hoc z WPA"
mode=1
frequency=2412
proto=WPA
key_mgmt=NONE
pairwise=NONE
group=TKIP
psk="abcdefghijkl"
Here is a command which I've used.
wpa_supplicant -Dwext -iwlan0 -c ad_hoc.conf
I've based it on this page: https://wiki.archlinux.org/index.php/Ad-hoc_networking
My network card is: Intel Corporation Centrino Wireless-N 1000

If you want WPA, then your key_mgmt and pairwise are definitely wrong. I'd say don't set key_mgmt, pairwise and group at all, the defaults are ok.

Similar Messages

My iPod 5th gen connects to wifi but the internet doesn't work.

So we were watching netflix on the ps4 and something happened and now my ipod will connect to the wifi but the internet doesn't work. everything else connects just fine to the internet just not my ipod. I've renew my lease, reset my settings and network, forgot my network and rejoined, turn my ipod completely off and back on, turned my wifi off then back open. The IP address is 192.xxx.x.xx
its the ipod 5th generation 16gb. With the latest update

Does the iOS device connect to other networks? If yes that tend to indicate a problem with your network.
Does the iOS device see the network?
Any error messages?
Do other devices now connect?
Did the iOS device connect before?
Try the following to rule out a software problem:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power off and then back on your router
.- Reset network settings: Settings>General>Reset>Reset Network Settings
- iOS: Troubleshooting Wi-Fi networks and connections
- Wi-Fi: Unable to connect to an 802.11n Wi-Fi network
- iOS: Recommended settings for Wi-Fi routers and access points
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem and it does not connect to any networks make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar

TS1398 The wifi on my iPod doesn't work since upgrading the software to ios 6 therefore when I try to reset to the original settings I can't get my original software back. Can anyone help me with this?

The wifi on my iPod doesn't work since upgrading the software to ios 6 therefore when I try to reset to the original settings I can't get my original software back. Can anyone help me with this?

greeneygreeney wrote:
so you can't ever restore it to the factory settings? that is a big shame.
"It will ALWAYS restore to the lates available software.
You cannot downgrade."

Wifi shows connected but doesn't work

My iPhone 4 shows that it is connected to my home network, but the wifi doesn't work. I know that the router is working because another computer on the network is working fine.

Try following:
Delete the WiFi network from your iPhone.
Disconnect the WiFi router from the power cord, let it be a few minutes, then reconnect.
Reset the iPhone by holding the Power button and the Home button at the same time, keep holding, ingnore everything on the screen, until you see the white Apple logo, then let go and let the iPhone restart. Set the WiFi t on and put in the password.
That should do it.

Got M-Cell that gives 5 bars, got full-strenth wifi, Internet on phone doesn't work, any app that uses internet doesn't work, seems like its started when upgraded to 7.1.1

I have an AT&T M-Cell that gives 5 bars, got full-strenth wifi. Same wi-fi that my computer uses, that my Kindle uses. So not capacity issue. but my Internet on phone drops out continuously and frequently, any app that uses internet doesn't work at all. It seems like it started when I upgraded to 7.1.1 I have connectivity like crazy, so why doesn't the internet work?

Reboot your router by powering it down for 30-60 seconds.

My wifi was disconnected and turned back on. Now my phone either won't connect to the wifi or connects but doesn't work

My wifi was disconnected and turned back on. Now my phone either won't connect to the wifi or connects but doesn't work

Reset network settings.
Settings > General > Reset > Reset Network settings.
Then re-connect to WifI by setting it up again.

Ad hoc connection doesn't work with my 3gs but works with my touch

I setup an ad hoc connection on my laptop following a guide on the internet.
I did this on windows 7 32bit, it worked for my ipod touch but for some reason it won't work with my iphone 3gs (upgraded with the latest updates)
I connect to the wireless network, it shows its connected (with the wifi symbol at the top in the iphone's status bar) but as soon as i try using the internet via safari or any other app, it reverts back to using 3g or edge networks. I've checked and after reverting it still shows wifi is connected but the wifi symbol is no longer in the status bar and judging by the speed of the connection it really isn't connected to wifi.
Any ideas why this is happening?
It's just so odd that it works on my ipod touch but not on my iphone 3gs... Can't be a windows related problem.

Did you ever get this fixed? I'm having the same problem and can't figure out the solution.

Ipad2, AppleTV2, WiFi. The mix doesn't work

Hi
When I try to connect my iPad2 to an Apple TV2, the wifi connection breaks down. Everytime. Sometimes it works only with the app "Immage" but never with Video or other else.
I've a MacBook Pro 15 (OS 10.6.8) but it works great with AppleTV2 and AIrPlay. The problem appears only when I try to use AirPlay between Ipad2 and AppleTV2.
AppleTv 2 - OS 4.4.2
IPad - OS 5.0.1
WiFi connection in "G" mode.
Thanks

I thought about it but it's a telephone company's router. And It doesn't explain why the system works between MacBook pro and AppleTV2.
Thanks

Intel WiFi/WiMAX 5150: HOTKEY doesn't work without Access Connections

Our company has several T410i 2522-P38 notebooks with Intel 5150 WiFi/WiMAX cards, all still running XP. Recently I had to reinstall OS on one machine. There was a minor problem that Lenovo support site download page for this machine offers Intel WiMAX 6205 instead of 5150, but I have driver package stored. However, after installing OS, drivers and Lenovo packages I've found that in Fn+F5 window I see only Bluetooth adapter, WiFi and WiMAX don't appear, yet they are correctly shown in Device Manager and WiFi works (couldn't check WiMAX).
This is not first time I face such problem, so I tried to solve it in usual way: uninstalled and reinstalled Hotkey package and drivers (Power Management driver and WiFi), tried several different versions of drivers and Hotkey - all to no success. Whatever I was doing, only BT was seen in Fn+F5.
Finally I ended up reverse-engineering Hotkey, and got quite unexpected result: it simply doesn't know WiFi driver present on the notebook. Hotkey package (namely, TpFnF5.exe file which creates Fn+F5 window) has a hard-coded list of known adpater Hardware IDs. Intel WiFi Link 5150 present on the notebook has ID VEN_8086&DEV_423D&SUBSYS_13168086, while closest match in the list was VEN_8086&DEV_423D&SUBSYS_13118086. As an experiment, I've patched TpFnF5.exe to replace "13118086" with "13168086", and voila - WiFi appears in Fn+F5, and can be switched on and off! I've checked TpFnF5.exe from several different versions of Hotkey package, and Hardware ID of our adapter wasn't present anywhere.
Ok, the reason is found, but how all other identical machines work?! I checked another notebook, and found the difference: it had Access Connections installed, while the troubled machine had only Hotkey but not AC. It turns out that Access Connections has it's own executable for Fn+F5 dialog, AcFnF5.exe. When you press Fn+F5 with AC installed, AcFnF5.exe is launched instead of TpFnF5.exe which is called when you have only Hotkey. And AcFnF5.exe knows how to handle our adapter. I've installed AC on troubled notebook, and Fn+F5 window immediately showed all three adapters.
Also, regarding WiMAX, it looks to me like this functionality was simply intentionally blocked in Hotkey. But I didn't dig further in that direction.

Ah, that's OK then.
Open Network Utility in Applications>Utilities, Traceroute tab & enter Apple.com, how far does it get?
Traceroute has started ...
traceroute: Warning: apple.com has multiple addresses; using 17.142.160.59
traceroute to apple.com (17.142.160.59), 64 hops max, 40 byte packets
1 clearmodem (192.168.15.1) 1.958 ms 0.749 ms 0.699 ms
2 * * *
3 10.41.164.213 (10.41.164.213) 58.679 ms 53.170 ms 65.443 ms
4 64.13.115.205 (64.13.115.205) 74.614 ms 55.570 ms 94.975 ms
5 64-13-49-226.war.clearwire-dns.net (64.13.49.226) 80.057 ms 85.445 ms 59.745 ms
6 xe-10-3-0.edge1.Seattle3.Level3.net (4.59.232.9) 119.813 ms 54.932 ms 55.217 ms
7 GOOGLE-INC.edge1.Seattle3.Level3.net (4.59.232.22) 94.901 ms 95.297 ms 89.508 ms
8 17.0.134.80 (17.0.134.80) 85.456 ms 17.0.134.70 (17.0.134.70) 60.254 ms 85.788 ms
9 17.0.132.98 (17.0.132.98) 69.673 ms 90.807 ms 17.0.132.96 (17.0.132.96) 99.968 ms
10 * * *
11 * * *
12 * * *
13 * * *
14 * * *
15 *
We want to see if it's getting past your Modem or Router.

I am trying to connect an airport extreme to extend my wifi coverage and it doesn't work

I hope someone can help me.
I have an Apple Airport extreme gen 5. I have a BT router/modem that I connect to my broadband and its signal is OK but not great. I have multiple apple devices, a windows PC, and a Panasonic smart TV.
I also use Belkin poweline adaptors to attach the TV and apple TV to my network - its flaky.
I was trying to attach the airport extreme to a powline adaptor in the lounge to extend my wireless network - it was green for a while but then flashed orange and stopped working.
I have now reattached it directly to my router in the same room with an Ethernet cable and still get the orange light and the airport utility keeps asking to attach to the WAN port but then nothing works - I can still acccess the internet through my existing bt modem/router.
Any ideas please?

Click the Wireless tab just below the row of icons
Make sure that the setting for Wireless Mode is set to Create a wireless network
The Wireless Network name would be the same name as the BT network
The Wireless Security would be the same setting that the BT router is using....should be WPA2 Personal or WPA/WPA Personal
The Wireless Password would be the same password as the BT network
Verify Password
Click the Internet icon
Click the Internet Connection tab just below the icon
The setting for Connect Using should be Ethernet
The setting for Connection Sharing should be Off (Bridge Mode)
Click the Update button at lower right of the window and allow a full minute for the AirPort to restart
Power off both the BT modem/router and the AirPort
Wait a minute
Power up the BT device first for a few minutes
Then, power up the AirPort
Everything above is a "quick fix". If that does not work, we will have to start all over again from scratch.

My wifi is connected but doesn't work

The download speeds on my iPhone 4 via wifi dropped from 18+ Meg's to .23 Meg's
The upload speeds are good at about 7.8 Meg's and holding.
My phone always shows signal and connection and doesn't
Disconnect at all. I have had this phone for a year and this issue started the
Beginning of dec. Is there a seperate transmit and receive antena?
Any ideas would be great.
Thanks

The wifi is connected I've verified this by enabling airplane mode.
The icon for wifi is on and I can pass limited traffic.
(see former post). Turned off cellular data and 3G too.
I get .23 on the download and 7.9 on the upload.
So I'm pretty sure I'm connected to the wifi access point.
I'm showing the phones Mac address in the routers arp table too.
4 laptops, 2 other iPhones and 2 iPod touches all connect to this same
Access point with speed test results from 10-18 Mbps On the download.
3-8 Mbps on the upload.

The wifi on my iPhone doesn't work

How can i fix the problem with m'y phone?

Hi Auroraamelia,
If you are having issues with the WiFi on your iPhone, you may find the following article helpful:
iOS: Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/TS1398
Regards,
- Brenden

Paring Z3 via WiFi with Pc companion doesn't work

Keep trying again and again with Sony's original USB cable without success
Windows 8.1 with latest Pc companion software

Sorry to hear that you have issues connecting with your PC.
Have you tried the suggestions in this thread: http://talk.sonymobile.com/t5/Xperia-Z3-Compact/Wireless-Media-Transfer-Pairing-done-but-connection-...?
- Official Sony Xperia Support Staff
If you're new to our forums make sure that you have read our Discussion guidelines.
If you want to get in touch with the local support team for your country please visit our contact page.

Wireless adapter Z-Com XG-703A doesn't work with WPA after reboot

Hello everybody,
Arch doesn't load kernel module arc4 during boot with usb wireless adapter Z-Com XG-703A. So WPA doesn't work and It can connect to only opened access points.
I found two work arounds but I don't know how to fix the issue completely.
1. Remove usb adapter and plug it in again (it causes arc4 module to load), then restart networking.
2. rmmod p54usb, rmmod p54common, modprobe arc4, modprobe p54usb and after that restart networking.
Could anybody help to fix the problem generally?
$ lsusb
0cde:0008 Z-Com XG-703A 802.11g Wireless Adapter [Intersil ISL3887]
$ uname -a
Linux arch 3.1.9-2-ARCH #1 SMP PREEMPT Sat Jan 14 08:11:41 UTC 2012 i686 Intel(R) Core(TM)2 Duo CPU E6850 @ 3.00GHz GenuineIntel GNU/Linux
Stas

Does the p54common get loaded again as well when you do modprobep54usb?
If not, you might just put that into modprobe.conf blacklist.
If it does get loaded as well, there might be another wireless module getting loaded that perhaps does cause problems. You can check that with
mkinitcpio -v
now, or with lsmod after a reboot before your workaround.

Synchronisation of photos from Aperture doesn't work with iPad4 and Apple TV

IPad4 with IOS 7.1.1
ITunes 11.1.5
Doesn't work with Aperture!
I couldn't synchronise my albums after upgrading Aperture to the latest software version, both for Apple TV and iPad2/iPad4.
Recovery of Aperture Mediathek doesn't help.

Could there be a relationship with the fact tha wifi syncing with itunes doesn't work too?
Also: I installed vlc remote last week which also gave connection problems. After manual input of ip adress and port it worked fine. Still I don't understand why. I have just a regular home network. Moreover apple remote combined with itunes just doesn't work still.
Any hints?

Wifi ad-hoc. WPA doesn't working.

Similar Messages

Maybe you are looking for