Windows XP and MSI KT4 ULTRA 6590-FISR

Has anyone figured out how to do a clean install of Win XP with this board?
I keep getting a "Device Not Certified error", at which point I elect to IGNORE the error and continue. There is absolutely NO INDICATION of what the problem device is.
However, at exactly 34 minutes left "Installing Windows", the installation routine locks up and I can't go any further.

The 2nd day into this,(I am on day 5) I took out my RAM and replaced it from another machine...same problem.
I then took out my PS and replaced it from another machine...same problem.
Diagnosing/testing all RAM and the PS showed no problems.
I then went through the BIOS and performed a multitude of enabling/disabling system settings. By disabling the following INTEGRATED PERIPHERALS/OnBoard PCI Controller Item:
LAN Controller
I was able to get Windows XP to load.
However, I cannot get XP to boot...not in NORMAL, or SAFE or SAFE with NETWORK, SAFE with PROMPT. But I am making progress.

Similar Messages

Linux and MSI KT4 Ultra : DVD problems

Hi, I own an MSI KT4 Ultra Pure mobo. The vt8235 Southbridge is supported in the lastest version of the Linux Kernel, 2.4.20 . After upgrading the kernel all seems to work fine, but when the system try to initialize my hdc (Secondary master of IDE, a DVD reader DV-5800A from NEC) it locks up with the message :
hdc: device {Busy}
hdc: drive not ready for command
ide1: reset success!!
and start looping with this message.
What can I do to get work my DVD Reader? With my precedent MoBo it works perfectly
Thanks
Bye

Hmmm that error used to happen with an older kernel and an ALI chipset. If you leave it long enough does it give up trying and continue to boot? The ALI did this eventualy.

Need Help for msi kt4 ultra (6590)

Mine Windows XP is not compatible with the promise serial ata driver ;(
The system is much unstable one
I cannot use the controller serial ata
What I can make??
Thanks
Fede

During installation XP it says to me that the driver they have not exceeded the compatibility test.
Windows advises me not to continue.
But I can make to work the raid with a single disc ATA
Thanks
Fede

MSI KT4 Ultra 6590 destroyed "L19"

Hi!
While trying to change the cooling system I pushe my srew driver too much in so I destroyed the Spool (??) L18 near the CPU which is (At least in my opinion) important for the AGP, which means that the Computer boots normally but without image on the screen!
The Question is: how can I change the spool?
Where can I get one to replace it??
which Induction Capacity does it have to have?
mike

Hi,
The answers to your questions I got from MSI for L18:
it can only be done if he has knowledge or experience in soldering
normally, the spare parts can be bought on hardware parts store selling capacitors/resistors etc.
L18,inductor,10n/5%,0603,400mA,RDC=0.26 ohm

KT4 ultra (6590) and Randeon 8500 instability

This is my pc:
Msi Kt4 Ultra (6590)
Athlon Xp 2000+
512 mb ddr pc 2700
Ati Radeon 8500 Ret.
maxtor diamondplus 8 80gb
Pioneer DVD 16x slot-in
Asus ISDN Adapter internal
Skystar 2 DVB sat Adapter
Power Supply Deer 350 W (amd certificaded)---- 5v/35A
3,3/24A
Monitor 19" Philps 109B.
S.O WinXP PRO SP1.
My systems runs great but when i play games sometimes my system crash and (very curios) before about 3-5 min of game play i see small interferences like small white orizzontal jolt similar the interference when a cellular phone ring near the monitor. the problem it persists with any resolution and any monitor refresh rate !!!!!
What i've tested:
I have the lasted KT4 ultra bios, test any Randeon Drivers (include the lasted 779 beta drivers) and lasted via's drivers
Near my monitor there isn't any interference source !!
Monitor is perfect (tested in other system )
it's not Radeon8500 problem because i play games perfectly in other system (a7v266 and same hardware)
KT4 are not damaged because i play game perfectly with another video card (geforce2 Mx400)
It's not a PSU problem because i replaced AMD athlon 2000 + with AMD Athlon 900 (the rest hardware is the same) and the problem it persists.
although i have 5 years experience under PC assemblage , I do not know that what to make!!!
is There an incompatibility with Radeon8500 and KT4 Ultra ??
Please someone can help me ??? ;( ;(

It might be the AGP driving value problem. Set it to EA in BIOS. It works for most people with components like yours. If that does not help, switch to AGP 2x and see if the problem went away. If it did, look for other DGP Driving values and turn off some AGP related features (sideband, fastwrite etc)
If that did not help,
See this post and try to draw come conclusions. Sometimes the Power Supply is at fault not because of being underpowered (which you checked with Athlon 900) but because of the incorrectunstable voltages and other similar crap. With 266Mhz fsb and 333Mhz memory interface the boards now are too sensitive to cheep power supplies.
Good Luck
KT3 Ultra2
Athlon 1800+
PowerColor Radeon8500 128mb
No-name 512 memory
No-name 400W power supply

PROBLEMS AGAIN, MSI KT4 ULTRA GIVE POOR STABILITY IN MY SYSTEM!!!

Hi, i get problems when overclock (fsb) my cpu with 133 fsb to 136 ONLY!!! , only support the overclock my cpu 1800(1533mhz)--to(1580mhz), high fsb 137 or high freeze , restart my system when run games or aplication with geforce 3 ddr 64mb, i modify vol agp to 1.8 , but get error again.
HELP ME!!!
I NEED NEW BIOS THAT STABILIZE MY SYSTEM!!!
System:
MSI KT4-ULTRA 6590-SR
CPU XP 1800+
256 DDR SANSUMG
T.VIDEO GEFORCE 3 DDR 64 detonator 41.09 agp4x
WINDOWS XP PRO SPK1
POWER 350 WATTS CODEGEN

Thanks for you help, but my power 350 watts codegen work a:
20A---3.3v
30a---5v
However i read guide revision 12-12-02 about psu and all configuration is correct !!!!!!
My powersupply not is problem
I NEED THAT MSI MAKE NEW BIOS FOR KT4-ULTRA!!
Thanks

MSI KT4 Ultra-SR (MS-6590) And IDE3

Rig is As Follows:
MSI KT4 Ultra-SR (MS-6590)
AMD Athlon 1000Mhz :(
512MB DDR333 (PC2700) x1 stick
MSI GeoForce 4 Ti4200 8)
IDE1: Western Digital 40Gb 5400rpm (win xp pr) as master & Maxtor 80Gb 7200rpm as slave
IDE2: Liteon 52x24x52 CD-RW ) as master & Samsung 12x DVD as slave.
Soundblaster 5.1 Live PCI
350w Power Supply
MSI D-Bracket 2 & S-Breackets Fitted Also.
I have Three Questions.
>My CPU has a FSB of 200, but the bios (version that came with board) shows it as 100 FSB. See here for athlon bus speeds
Is it ok to increase the bus speed without damaging the processor.
>The two brackets that i have fitted (s and d brackets) do not work. Why?
>What are the optimal and settings for my ram (PC2700 512MB DDR) and GFX Card (MSI GF4 TI4200).
>Oh yeah, my CPU is now operating at a higher temp than before (using old K7VZA ECS Mobo) @ 50-55. Is this normal??
Sorry for the n00b questions, it's just that this is the first time iv ever taken my PC to pieces and re-configured it myself :P
Thanks in advance. -RjA

I can help a little 1000MHZ AMD chip=200FSB XP CPUs=266FSB this is CPU speed . AMD 1000MHZ CPU needs to run @100FSB where a XP CPU can run @133FSB This is MEMORY speed . Trying to crank that poor old chip up to anything other than 100 will do you NO good. You need to buy a bigger cpu of the XP kind. A lot of the older XPs can be had for a low price. 50c isn't not super hot. My KT4 runs in the 40s. You might want to think about a bigger cpu cooler to bring the temps down a bit. Most of your settings should be left at system default, since you only have a 1000MHZ CPU. When you go up to an XP then you can make a few changes. Regards BIGDADDY51 :D :D

Upgrading to a MSI kt4-ultra FISR board.....

Currently I've got a gigabyte motherboard and I want to upgrade to an: MSI kt4-ultra FISR board. Can I just pull my old board out and install the MSI board with all my old hardware, O/S already on harddrive - and do a start up, or will I run into errors and problems when I try this? Currently my system looks like this:
1) Case: "Xaser SC5000BWII" 400watt mid-tower case
2) Motherboard: Gigabyte GA-7DXR DDR+Raid
3) CPU Chip: AMD Athon XP 1800 1.6Ghz
4) Memory: 512 of PC2100 DDR266 Memory
5) AudioCard: Creative SoundBlaster Audigy MP3 card
6) VideoCard: ATI RADEON 9000pro, 128 DDR
7) Hard Drive: Maxtor 80GB 7200RPM ATA-133 "D740X" Mdl:6L080J4
8) Operating System: Ms Windows XP Pro
Thanks for the help........ seboyd ?( :D 8)

A clean install will give you 30 days to reactivate and it only takes a 5 minute call to get the new #s. Pretty simple and much easier than trying to straighten out all the error codes from old O S. I did however move an XP harddrive from a Turbo2 to a KT4 without a new install but they were both MSI boards. A clean install also gets rid of all the junk that accumulates. Just enter bios and make the CD rom 1 st boot . BIGDADDY51 CT. USA :D 8) :D

MSI KT4 ULTRA MS-6590

I have this motherboard: MSI KT4 ULTRA MS-6590 sempron and I have already bought the new CPU SEMPRON (AMD Sempron 2400+). I want to know if my motherboard is compatible with new CPU.
Thank you
Sorry for my English, but I'm Italian.

Hi
Not according to http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_cpu_support_detail.php?UID=356&kind=1

MSI KT4 Ultra-FISR

Recent upgrade problem
Old: MSI kt266 pro-2, allied 300w atx psu, ati radeon ve 32m
New: MSI kt4 ultra-fisr, allied 400w atx psu, MSI geforce4 mx440-vtp, western digital 80g hdd
Unchanged: 256m pc2700 ddr, top-g 24-10-40x cdrw, maxtor 45g hdd, sblive platinum
Problem: After upgrading I have difficulty installing software by cd. Errors are spomething like (bad cab file)
occasional but random reboots
moving files on hdd causes reboots
can someone help? I've contacted MSI about it and really hope I won't have to send the board in as defective if it really isn't.. thanks

Hi,
I have the same issues with my KT4 Ultra (pure version).
Running GF4 Ti4400, Athlon XP2400+ etc, 450W power etc. There are quite many posts of similar issues all over the Via Arena forums and some here as well. KT4 Ultra's and KT4V's seem to be the boards affected.
Installing the Via USB Filter Patch helped with narrowing down the number of crashes and some of the errors.
(note: disable automatic restart from 'Startup and Recovery settings' to see the driver that crashes)
Link to Via Arena FTP site
I had a K7T266pro2-RU board before this which worked 100% stable. I've tested all my components which are fine. Tested different power supplies, memory. Still, continuous random errors after many times of reinstalling Win2K by the book and with default bios settings.
Sometimes the setup works fine for a week and then starts to mess around again.
Looks like setting the cpu fsb down to 128 MHz from 133 MHz solves the issues, so try that and report back.
Also check the filter patch.
I'm personally waiting for the next bios release to fix these issues - if not, I'm showing this board RMA and go to nForce2 chipset.
I also tested the 1.25 beta bios, which gave me lots of crashes during Win2K boot -> flashed back to v1.10 and booting works again.
- Tom

MSI KT4 ultra and AMD ATHLON 2600+ and Corsair 512Mb 3200

Hello,
i've bought a: MSI KT4 ULTRA and a AMD ATHLON 2600+
Today, i've updated the bios to the version 1.3! So: no problem to reboot after the process complete.
BUT, now i can't set the CPU at 2.16Ghz (280Mhz clock) because if i set the clock up to 100Mhz it doesn't reboot anymore! the motherboard detect the frequency @ 1250 Mhz :(((
Please: HELP ME
(sorry for the grammar and / the english) but i'm a french guy.

Hi,
I had the same issues, see the thread:
http://www.msi.com.tw/program/e_service/forum/viewindex.php?threadid=11717&boardid=13&styleid=1
Essentially I had to set (in the BIOS) the FSB to 166 and left the Multiplier on auto. This ment the processor was reported properly as 2600+, but the memory will only run at 333 MHz... Yeah I think I wasted the money on getting the latest and greatest memory too....
Had me worried for a while, I though my supplier had palmed a bad chip off on me.... It just that the board can't do the highest speed chips and the highest speed memory at the same time (it states that that is unsupported in the manual...)
hope the helps...

MSI KT4 Ultra and AMD XP3200+

Hi,
Is it possible to run an AMD Athlon XP 3200+ on the MSI KT4 Ultra Motherboard?
I know the motherboard supports FSB200/266/333, but will the cpu work if I manually set it to FSB400 in the bios?
Thanks for you help.

I don't think the cpu is unlocked, it is an original 3200+.
I thought you need an unlocked cpu if you want to overclock the cpu.
I just want to leave the multiplier on auto and set the frequency to 200MHz (its original setting).
The reason I need to know is that I stupidly bought the cpu without checking my motherboard FSB support and I cant return the cpu.
I have not received it yet and wanted to know if it was possible to get my computer up and running even if the KT4 Ultra does not officially support FSB400.
Would there be any harm in trying the cpu in my motherboard.
If anyone has managed to run an AMD XP3200+ cpu on a MSI KT4 Ultra, please let me know.
Thank You.

MSI KT4 Ultra and AGP 8X mode

Hello,
I have a MSI KT4 Ultra Motherboard but I can't set the AGP mode manually! It is set on AUTO!
I want to set it on AGP 8X!
I have a Radeon 9700 pro VGA card so it must be possibble to set it on AGP 8X
Please help me.......
Maurice Schreuder

It's at 8x already.
More info read the top KT4 Unofficial FAQ.

Problem with my MSI KT4 Ultra

Hi all!
I have a BIG problem, I have tried to look at this board, but there is many different answers out there ;(
I have KT4 Ultra with Athlon XP 2600+
I have set FSB to 166, and when I startup BIOS says Athlon XP 2600+.
But in windows system, it only says:
AMD Athlon XP2600+
2.09Ghz !!!!
768Mb RAM
Why is windows only says 2.09Ghz??
AND, I think my system is very slow. I used to have AMD 1200Mhz. And this sytem is almost like my last computer.
My System:
MSI KT4 Ultra ( MS-6590 ) with BIOS
CPU AMD Athlon XP 2600+
768MB DDR 400 RAM
GeForce 4 TI4200AGP 8x
80 Gb Seagate 7200 Harddrive

Quote
Originally posted by swedecom
Ok, I use these settings in my BIOS, are they right for my system??
MY SYSTEM:
MSI KT4 Ultra ( MS-6590 ) with BIOS
CPU AMD Athlon XP 2600+
768MB DDR 400 RAM
GeForce 4 TI4200AGP 8x
80 Gb Seagate 7200 Harddrive
MY SETTINGS IN BOIS:
Spread Spectrum = +- 0.25%
CPU FSB Clock = 166Mhz
CPU Ratio = Auto
CPU Vcore = (V) Auto
DDR Voltage (V) = Auto
Termination Vol (V) = Auto
AGP Voltage (V) = Auto
Hope someone can help me out

No optical-out sound on MSI KT4-Ultra!!

Hi, I have recently set up a system based on the MSI KT4-Ultra board. I'm using an Athlon XP 1700+, a Radeon 9000 video card, and I've installed Windows 98.
Although all the drivers and audio applications which MSI provided installed fine, and 2-channel audio from the on-board sound chip works great both for music and for the 3-4 games I've installed so far, I can't seem to get the optical SPDIF port to work! I bought a cable and connected the computer to my Sony MD-player and attempted to copy my CDs onto MD. I go into the MSI control panel and check the box to enable SPDIF-out, removing the speaker cable from the analog line-out just for good measure. When I plug the optical cable into my MD it recognises digital input and prepares for recording. I press record on the MD and play on the computer's CD-player app, but the MD LED shows "no signal". I'm pretty sure both the MD recorder and cable are OK since I've used them to copy CDs from a Kenwood portable CD-player quite recently, so it must be the MB that's giving me problems. Indeed, when I've stopped playback in the CD-player app and went back into the audio control panel, I found that the SPDIF box had been unchecked of its own accord. I've tried this several times, and I've unplugged the S-bracket and reinstalled it all over again just to make sure it was plugged in properly, and I still get the same problem. All audio works fine except optical out! Haven't got a coaxial cable or recorder so I can't check if the coaxial port is equally buggered or if it's just the optical, but I'm getting really annoyed here: this was the one feature I liked best about this board and the only one which isn't working! Any ideas, anyone?

dude, i think i can get u ur signal, but currently i can only get silent recordings, u may have better luck.
on the minidisc, there should be a switch or button that will toggle synchronised recording on and off, turning it off should get u a signal, but it wont be in sync wiv the cd, ie u cant trust it to form track gaps.
hope that helps, done flame me if it dont, if i manage to get substance to my recording, i will send u the info just in case.
take it easy

Windows XP and MSI KT4 ULTRA 6590-FISR

Similar Messages

Maybe you are looking for