Wireless AP will not connect and Radios stay down

Question

Hi,
I have recently configured a Wireless AP for our network. It is running flash:/c1140-k9w7-mx.124-21a.JA1/c1140-k9w7-mx.124-21a.JA1" .
I have configured the SSID's VLANS, subinterfaces BVI's etc. I have connected it to our switch infrastructure but i cannot seem to connect to it and the Radio interface is staying down.
Wireless AP Config:
dot11 ssid IMC-Wireless-Data
   vlan 10
   authentication open
   authentication network-eap AUTHVPN
dot11 ssid IMC-Wireless-Voice
   vlan 14
   authentication open
   authentication network-eap AUTHVPN
interface Dot11Radio0
no ip address
no ip route-cache
shutdown
antenna gain 0
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
antenna gain 0
no dfs band block
channel dfs
station-role root
interface Dot11Radio1.10
encapsulation dot1Q 10 native
no ip route-cache
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
bridge-group 10 spanning-disabled
interface Dot11Radio1.14
encapsulation dot1Q 14
no ip route-cache
bridge-group 14
bridge-group 14 subscriber-loop-control
bridge-group 14 block-unknown-source
no bridge-group 14 source-learning
no bridge-group 14 unicast-flooding
bridge-group 14 spanning-disabled
interface GigabitEthernet0
description IMC-Wireless-Data
no ip address
no ip route-cache
duplex auto
speed auto
no keepalive
interface GigabitEthernet0.10
description IMC-Wireless-Data
encapsulation dot1Q 10 native
no ip route-cache
bridge-group 10
no bridge-group 10 source-learning
bridge-group 10 spanning-disabled
interface GigabitEthernet0.14
description IMC-Wireless-Voice
encapsulation dot1Q 14
no ip route-cache
bridge-group 14
no bridge-group 14 source-learning
bridge-group 14 spanning-disabled
interface BVI1
description IMC-Wireless-Data
no ip address
no ip route-cache
interface BVI10
description IMC-Wireless-Data
ip address 10.10.0.245 255.255.255.0
no ip route-cache
interface BVI14
description IMC-Wireless-Voice
ip address 10.10.14.251 255.255.255.0
no ip route-cache
ip default-gateway 10.10.0.254
SwitchPort Config:
================
interface GigabitEthernet0/2
description IMC-SYD-AP01
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 10,14
switchport mode trunk
mls qos trust dscp
no mdix auto
spanning-tree portfast
Core Switch Vlan configuration:
interface Vlan10
description IMC-Switch1 - Data VLAN
ip address 10.10.0.252 255.255.255.0
standby 10 ip 10.10.0.254
standby 10 priority 110
standby 10 preempt
end
interface Vlan14
description IMC-Wireless-Voice
ip address 10.10.14.252 255.255.255.0
standby 14 ip 10.10.14.254
standby 14 priority 110
standby 14 preempt
The Logs in the AP come up as :
000022: *Mar  1 11:15:05.211 AEDT: %DOT11-4-NO_SSID_VLAN: No SSID with VLAN configured. Dot11Radio1 not started.
000023: *Mar  1 11:15:05.212 AEDT: %DOT11-4-NO_SSID_VLAN: No SSID with VLAN configured. Dot11Radio1 not started.
If anyone has any idea why this is an issue it would be greatly appreciated.
Thanks

Answer 1

Hi,
Pleas do the below changes..
en
conf t
int dot11 1
ssid IMC-Wireless-Data
ssid IMC-Wireless-Voice
no shut
end
en
conf t
int dot11 1.10
encap dot1q native 10
bridge-group 1
end
en
conf t
int gig 0.10
encap dot1q native 10
bridge-group 1
end
On the Switch
===========
interface GigabitEthernet0/2
description IMC-SYD-AP01
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 10,14
switchport trunk native vlan 10
switchport mode trunk
mls qos trust dscp
no mdix auto
spanning-tree portfast
lemme know if this helps and please dont forget to rate the usefull posts!!
Regards
Surendra