Working with HSRP on a Production Router

I want to setup and test HSRP, but I don't have a testbed or much downtime. Can I setup HSRP and my users still use the assigned addresses on the interfaces.
Ex.
10.10.10.1 is their def. gateway.
Create a HSRP address at 10.10.10.9.
I use the .9 for testing. They use the .1 address and aren't interrupted.

Hi,
Yes, they can.
If you don't want to change the default gateway on the user workstation and then you need use that address as the standby (HSRP) address. Set the priority to something higher than 100 on the active router.
You need a config like this one.
Active Router:
int f0/0
ip address 10.10.10.9 255.255.255.0
standby 1 ip 10.10.10.1
standby 1 priority 110
Standby Router:
int f0/1
ip add 10.10.10.10 255.255.255.0
standby 1 ip 10.10.10.1
HTH
Sundar

Similar Messages

What can I do to work with leadtools and IMAQ products?

I'm a Microsoft Visual Basic Developer and I'm trying to work with IMAQ devices and ActiveX libraries such as LeedTools. My problem is that this ActiveX objects need to work with TWAIN devices and National Instruments doesn't support TWAIN's standard.

Lucas,
NI's IMAQ products do not provide TWAIN support in their drivers, as to be called using the TWAIN protocol. There is a company called Graftek, www.graftek.com that has some LabVIEW TWAIN drivers. They might be able to give you a closer suggestions for solutions. But our boards do not support or are supported under the TWAIN protocol.
Good luck!
Nestor.
Nestor
National Instruments

Working with Standard mappings of product content

Hi,
Let me know any one worked with the (_MDMProductSetMsg,_ProductRelationSetMsg) standard mapping(s) for importing Taxonomy table data in to product repository..
Thanks,
Rupesh K

Tom has step by step here:
http://www.fcpbook.com/Video5.html
The subclips should behave like a regular clip.
If you experience flakey behaviour with FCE, trash the FCE Preferences.
When I view the subclip in the canvas and mark in and out positions
I hope you mean the Viewer where you mark in/out points otherwisw it won't work as expected.
Mark an in/out in the Viewer then drag the Viewer clip onto the Insert Canvas Overlay or Overwrite depending on the type of edit required.
Al

Elements working with Other Slide Show Products

We've had some debates here about slide show products other than the function within Elements. Personally I opted for Proshow Gold, which I've been very pleased with.
However, it lacks in one aspect and that's locating the files you want to put into a show. That's because I rely on the E3 Organiser to make sense of the thousands of folders and meaningless filenames I have. Proshow has an Explorer like interface which means you need to know where the image is actually stored on your hard drive.
So, naturally I thought I'd see if I could get Proshow to work along side the E3 Organiser.....and it does!!!
If you open both programs you can just select images in the Organiser Window an drag them into Proshow. So now I can create a Collection of the images I want in E3 and just drag the whole lot into Proshow.
It also works with Photostory 3 so may there are others that will work as well.
It did trip up once. An image got put into Proshow that wasn't one I'd selected but had the same name. It might have been part of a version set...I haven't figured that out yet.
Colin

Folks....
Back playing again....:-)
If you drop the images from the Elements Collection into the Proshow Light Box it does retain the order in which they appear in the Collection, albeit reversed, irrespective of date.
If you drop them into the Slide Show image collection bar at the bottom of the Proshow window then the order sometimes gets a little scrambled.
I'll disagree with Grant about ordering them in Organiser v Proshow. I find E3 Organiser easier to use. So I create a collection of images for the slideshow from the various folders I want, order them in the collection, select all and drag and drop.
Colin

Working with Projects instead of Production Order

Hi Experts,
In one of our manufacturing companies we are trying to implement SAP B1. The company has MS Access currently. We work with projects and each sales order consists of many projects. Taking it to SAP B1, there is the option of production orders but that works with Item no. for final product with BOM. Our product is not consistent and every time the product can change according to customer requirement. That means if we go with the SAP's production order functionality we will end up creating many (ghost) items everyday, and that (item) would be of no use next day. What can we do to solve our problem with SAP B1? Or SAP B1 can not handle projects? We are ok to work with SDK but not with a big cost.
Please help if possible.
Thank you.
Kind Regards,
IC

Hi,
There are actually many things which needs to be basically studied before a workable solution can be determined and its applicability can be assessed.
For sure, there are lots of Items involved and each Project(Lets say BOM) has different combination of items which are not standard but frequently change.
Here first it needs to be determined, do we need to keep a track on the items, its value and the left over ones as well, because items would be involved in the combination which would either be purchased or kept in inventory for future purpose.
Secondly, can it be feasible where we can define a standard BOM (project) which has the normal ingredients(items) to make the final product and then based on that some changes can be made when Production Order is created (like changing the child items (excluding some and including some).
And also, can there be some process by which we can add the volume of items in the database using some external tool, like SDK or an add-on.
Actually, there are lots to be thought about and tested. I would prefer if someone who has implemented such scenario/business gives you some guideline about his procedure.
Kind Regards,
Jitin
SAP Business One Forum Team

Does XSAN work with other HW SAN products

Will XSAN work with SANs other than XRAID? I am investigating building an XSAN environment with a Xiotech SAN, a Cisco fabric and XSAN.
James
Xserve Mac OS X (10.3.9) two Fibre Channel Cards

Hi James,
well yes. I have Xsan working with either Xserve RAID and some other FC-enabled RAID systmes. In my case I hooked up two StoreNext FC-RAIDs to our existing Xsan and they worked quite well.
The only problem I came across was, that in the beginning the PM G5 clients were only able to write to the new SAN volume but they couldn't read properly from it when the file size exceeeded 512 MB. Interestingly the PM G4s did not show this behaviour they worked right away with the new hardware.
My guess would be, that it has something to do with the new PCIe FC-cards that you need in the newer G5s.
Anyway, I solved this by reducing the stripe size for the storage pool from 256 to 64 blocks resulting in 256 KB stripes.
From thay change on everythign worked flawlessly and I could not even notice for any speed bumps.
Cheers,
Stephan

Encore's Cancelation & will not work with CC Dynamic Link Products

Adobe has aparently canceled development on Encore. I have just upgraded to thier Creative Cloud and discovered that Encore will not connect with Premiere or AE through Dynamic Link.
I'm in the Video Production business, my clients & I still very much use the DVD & Blu-ray format.
Wedding & Event videographers rely on the DVD/Bluray format to deliver thier products to thier clients.
It's one thing to stop developing the app but to exclude it from the Dynamic link...how tough can it be to hook up hte CS6 version (any developers out there?).
Yes I can read the writing on the wall and DVD days are numbered—however Adobe has prematurly canceled a product that It's loyal customers relay on. Yes I know it still works, but I sure will miss the Dynamic link.

Yes, there is even a subforum devoted to this absurdity. I believe there is more to the story, related to the takeover of Sonic by Rovio, and their abandoning Scenarist.
I assume you have seen these, but if not:
See this link, which includes how to install Encore CS6, how to get the library, and a tutorial on workflow with Premiere CC.
http://helpx.adobe.com/encore/kb/encore-cs6-installed-cc.html
Also, see the Encore CC/CS6 FAQ:
http://www.adobe.com/products/encore/faq.edu.html

How do I Get My Router to Work With iChat ? FAQ 2

Replaces iCh: FAQ 2 How to get my router to work with iChat?
Getting your router started with iChat.
Appropriate for using iChatAV 2 upwards
Glossary for this FAQ
Routers: Any configurable device that sits between your computer and the internet link you have.
Routers seem to fall into two categories
Those that work straight from the box. See Apple Doc 93333
NOTE
This Doc has not been updated since Jan 04
and those that do not.
This post will deal with what you may need to look at.
First off make sure your device is acting as a DHCP server. (if you are already on the internet you may not have to bother with this.)
Check in the Network Preference Pane, in the "Built in Ethernet" option from the "Show" drop down list.
Make sure the TCP/IP tab is the 'front' one. You should be able to see Configure IPv4 and it most likely reads Using DCHP. Make a note of your IP address. It will start 10.xxx.xxx.xxx or 192.168.xxx.xxx (the 'x' s will stand for any number between 1 and 255).
Your router is most likely to be configurable from your browser. You will need to find the IP address to type into the browser from any Readme or PDF files that came on the install disk or visit the makers website and download a manual.
DMZ Demilitarised Zone
This is a less secure setting that basically opens all ports and points the incoming data to your computer. (not helpful if you have more than one computer on your LAN)
NAT Sometimes called NAPT and related to Port Forwarding (also Virtual Server or Pin Holes)
These settings are usually found in an Advanced setting.
You will need to set an incoming IP address (Usually 0.0.0.0 for any outside server), a port that data will arrive on, the Inside computers IP address (your computer) and the port it will deal with the data on and the protocol it will use.
iChat uses TCP and UDP so some devices will need the settings done twice, once for each protocol.
See Apple Doc 93208 for more information.
Note:
Note 1 should read:
1. All iChat AV traffic is UDP except for ports 5190 and 5298, which need to be open for both TCP and UDP; and 5220, 5222, which need to be open for TCP only.
UPnP Universal Plug n Play.
This is a simple Plug and Play type of setting. iChat can find it's own way through a router if the device has this capability.
Trigger Ports
Some devices offer a security measure that works by a first or trigger port receiving a data packet and then opening further ports when accepted.
The first port for incoming Video or Audio invites is port 5678. When you click on the invite window the process moves to port 5060 (so these will need to be opened by the trigger port) for negotiating the final group of ports from the group of 20 (16384-16403 These will need to open when the trigger says so as well). Therefore port 5678 triggers ports 5678, 5060, 16384-16403. All on UDP. Port 5190 neeeds to trigger port 5190 for both TCP and UDP
Wireless
Here you will have to read around but this Apple Doc 58514 might be a good starting place.
Multiple devices
Make sure only one is acting as a DHCP server. Make sure wireless devices are bridged properly.
Further Help
I have found that this site (ADSLGuide) to be helpful.
It is British based but I have linked you to the Apple Related Discussions Forum.
Eliminating Problems on my Personal web pages.
The ports and their function within iChat. (my pesonal Web pages again)
This is not a step by step approach. You will have to read around the information about your device.
Collected FAQs and Expansions: Index Page
Also http://www.portforward.com/routers.htm for instructions with Pics on Port Forwarding.
Ralph
G4 Dual 1Ghz MDD with extra HDs X3. Mac OS X (10.4.3) Have you read the iChat FAQs ?? They have moved to Users Tips

Replaces iCh: FAQ 2 How to get my router to work with iChat?
Getting your router started with iChat.
Appropriate for using iChatAV 2 upwards
Glossary for this FAQ
Routers: Any configurable device that sits between your computer and the internet link you have.
Routers seem to fall into two categories
Those that work straight from the box. See Apple Doc 93333
NOTE :This Doc has not been updated since Jan 04
and those that do not.
This post will deal with what you may need to look at.
First off make sure your device is acting as a DHCP server. (if you are already on the internet you may not have to bother with this.)
Check in the Network Preference Pane, in the "Built in Ethernet" option from the "Show" drop down list.
Make sure the TCP/IP tab is the 'front' one. You should be able to see Configure IPv4 and it most likely reads Using DCHP. Make a note of your IP address. It will start 10.xxx.xxx.xxx or 192.168.xxx.xxx (the 'x' s will stand for any number between 1 and 255). The range 172.16.xxx.xxx is also a possible value at this point. Rarely used, but it is part of the RFC for Address Allocation for Private Internets.
Your router is most likely to be configurable from your browser. You will need to find the IP address to type into the browser from any Readme or PDF files that came on the install disk or visit the makers website and download a manual.
DMZ Demilitarised Zone
This is a less secure setting that basically opens all ports and points the incoming data to your computer. (not helpful if you have more than one computer on your LAN)
NAT Sometimes called NAPT and related to Port Forwarding (also Virtual Server or Pin Holes)
These settings are usually found in an Advanced setting.
You will need to set an incoming IP address (Usually 0.0.0.0 for any outside server), a port that data will arrive on, the Inside computers IP address (your computer) and the port it will deal with the data on and the protocol it will use.
iChat uses TCP and UDP so some devices will need the settings done twice, once for each protocol.
See Apple Doc 93208 for more information.
Note:
Note 1 should read:
1. All iChat AV traffic is UDP except for ports 5190 and 5298, which need to be open for both TCP and UDP; and 5220, 5222, which need to be open for TCP only.
UPnP Universal Plug n Play.
This is a simple Plug and Play type of setting. iChat can find it's own way through a router if the device has this capability.
Trigger Ports
Some devices offer a security measure that works by a first or trigger port receiving a data packet and then opening further ports when accepted.
The first port for incoming Video or Audio invites is port 5678. When you click on the invite window the process moves to port 5060 (so these will need to be opened by the trigger port) for negotiating the final group of ports from the group of 20 (16384-16403 These will need to open when the trigger says so as well). Therefore port 5678 triggers ports 5678, 5060, 16384-16403. All on UDP. Port 5190 neeeds to trigger port 5190 for both TCP and UDP
Wireless
Here you will have to read around but this Apple Doc 58514 might be a good starting place.
Multiple devices
Make sure only one is acting as a DHCP server. Make sure wireless devices are bridged properly.
Further Help
I have found that this site (ADSLGuide) to be helpful.
It is British based but I have linked you to the Apple Related Discussions Forum.
Eliminating Problems on my Personal web pages.
The ports and their function within iChat. (my pesonal Web pages again)
This is not a step by step approach. You will have to read around the information about your device.
Collected FAQs and Expansions: Index Page
Also http://www.portforward.com/routers.htm for instructions with Pics on Port Forwarding.
With thanks to Macmuse.
Ralph
G4 Dual 1Ghz MDD with extra HDs X3. Mac OS X (10.4.3) Have you read the iChat FAQs ?? They have moved to Users Tips<</a>/span>

Will aiport express work with osx v 10.6.6

Will airport express work with an old netcomm NB6 router modem using osx v 10.6? Or do I need to buy a better modem first?

My airport express is quite old. Model A1088.
This model was discontinued about 7-8 years ago, so the product is at least that old, probably older than that. On average, the Express will last about 5 years.
I can't seem to get my airport utility to find this. Airport utility is the latest version.
Not sure what you mean by latest version of AirPort Utility. That would be a 6.x version, which does not support the older model of the Express that you have.
Or, did you mean to say that you have the latest version of AirPort Utility 5.6.1.....which would be the correct version for the Mac running (10.6.6)?
Please clarify.

Crop a background image (movie) - working with a template

I'm working with the template "Promo > Product Shot". The image block with the bike is what I want to replace with my own video clip.
I can't figure out how to replace it, so I took the video clip and "placed" it. That's all fine, but now I want the size of the video clip to match the size of the bike block. I can scale it down to get close but then I'd have to crop the sides to get the vertical block shape.
Can't figure out how to do this either. Is it even possible?
Thank you very much,
Eric P

Thank you for the speedy reply.
I played with that tab a little but didn't understand exactly what it was so I never followed through with it.
I did follow your steps, but nothing happened. Perhaps there is something I have to do after selecting the movie?
Thank you,
Eric

RV082 UPnP not working with Back To My Mac

I have several Mac based applications that are not working with UPnP on my RV082 router. It's not listed as a compatible router on Apple's MobileMe Back To My Mac hardware compatibility list. Is there a way to manually configure port forwarding for this application?
Another application that requires UPnP that is not working is El Gato EyeTV.
UPnP is on, and some applications on some computers are clearly able to open ports via UPnP.
I have firmware version 1.3.98-tm.

You will need to contact the vendor/manufacturer of the specific non-Cisco applications (Back to My Mac & El Gato EyeTV) for those application instructions, we don't support them on here. if the RV082 is working with other devices/applications, then I'd believe that it's specific to those non-Cisco apps that you would need to troubleshoot with the specfic vendors on.
Best Regards,
Glenn

WRT600N not working with Mac OS X - Please help

I previously had a WRT54G and it was working fine (until it died) with my MacBook Pro laptop. I just replaced it with a WRT600N and the MacBook Pro is no longer seeing either of the two wireless networks being transmitted by that new router. However, when I boot the MacBook Pro in Windows Vista through BootCamp it sees the networks with no problem. Is the WRT600N incompatible with Mac OS? If so, is there or will there be a patch soon (and where can I find it)? I also have a WRT300N running and it is being seen just fine by both the Mac and WIndows sides of the MacBook Pro. The problem is only with the WRT600N and the Mac OS. Any ideas or suggestions would be appreciated.
Thanks.

Try using WPA2 Personal - AES encryption, that is the only config that worked with my older WRTG54? router and a new macbook.

Linksys WRT54G router--Why doesn't it work with my Macbook?

I have a perfectly functional Apple MacBook (Unibody, late 2008) running Leopard 10.5.6. I have used it to connect to public Wi-Fi but it is unable to connect to my home Linksys WRT54G router. I called Apple Tech Support, and they suggested that I change the wireless channel and/or temporarily remove the WPA encryption. I did both, the computer still could not connect. In System Preferences on the MacBook, it tells me that "AirPort does not have an IP address and cannot connect to the internet." The tech support guy tried to help, but in the end basically told me that the router just plain might not be compatible with Apple products. (My iPod Touch cannot connect either.)
I can buy a new router, but this one works perfectly for the rest of the computers in the house (PCs) and they're expensive--and there's no guarantee that those will work either.
So: Does anyone know any solutions short of buying a new router that would make my Linksys compatible with my Macbook AND our home PCs? Or, failing that, a good, WPA-encrypted router that WILL work with both?
I have a Snow Leopard disk (I just received the computer on Thursday). Would upgrading to Snow Leopard be of any help? I'm planning on doing it anyway one of these days.
Many thanks in advance,
Sola Gratia

You are in the wrong forum but I'll try and help anyway. That model of Linksys router has a long history of not getting along with Apple products. That is not to say it will never work, but it does require that you download and install the latest firmware for the exact model of router that you have. There are multiple sub-models of that router so make sure that you get the right one.
Once you have done the firmware update, restart your router and try it again. WPA-psk should work but for troubleshooting purposes, turn off encryption and see if you can get your MacBook and touch working. You might want to use WPA2-psk instead of WPA.
I would hold off on Snow Leopard until you get WiFi working. Nothing like changing to too many things at one time to really mess things up.

Policy Based Routing is not working with slb configured

I have a 7609 with a slb firewallfarm configured. It is running IOS 12.2(18)SXE3 with sup720. The firewallfarm is configured with default settings with no access parameter, only real servers configured.
All the traffic is coming from a single vlan (it's not possible to implement another layer 2 way to make the traffic pass through) and I would like to make a single flow to exit from another interface and not pass to the real servers configured on FWfarm. I wrote the following PBR statements:
!!!!!!! Begin !!!!!!!
access-list 110 permit ip host XX.XX.XX.XX any
!where XX.XX.XX.XX is an omitted IP address
route-map NEW-ROUTEMAP permit 10
match ip address 110
set ip next-hop 192.168.253.3
interface Vlan55
!vlan 55 is the interface from where the selected flows comes
ip route-cache policy
ip policy route-map NEW-ROUTEMAP
!!!!! END !!!!!!!
The route-map seems working, in fact I can see matched ACL and route-map.
The problem is the SLB seems to take all the traffic in charge, also the one I would like to route to another interface, in fact if I put my desidered output interface in monitor I can see no traffic passing through.
SLB creates the sticky entry anyway, in fact as far as I know, the SLB has the priority to static routing and route-maps.
Any idea for a workaround? Is there a way to make PBR works with SLB?
Thanks in advance.
Ric

It's possible to make pbr work with slb for further details refere to the link ,
http://www.cisco.com/en/US/customer/products/sw/iosswrel/ps1835/products_configuration_guide_chapter09186a00800ca75d.html

Does The Airport Express Work with Any Router?

Hi Forum,
i have an old Linksys router G Wifi speeds, does the Airport Express work with this?

The AirPort Express or other Apple routers will not wirelessly extend the signal from your Linksys router, if that is what you are asking here.
If yes, use another Linksys product to insure compatibility between devices.

Working with HSRP on a Production Router

Similar Messages

Maybe you are looking for