WRT54GS and MS Outlook connectivity issue

Hello All,
i have just got the WRT54GS wireless router, i have configured it and it is working. however MS Outlook is not able to connect to exchange server (i am using MS Outlook in cached mode and connectivity over HTTP) when i connect directly to the modem it works fine with no problems at all.
also not all the web pages are accessable through the router and not all the time.
i understood that prot triggering should solve my issue along with setting manual MTU. anyone can please help and tell me what are the exact ports i need to trigger ? any idea on the correct MTU?
thanks in advance for help.

thanks for the advise, however this requires knowing the ports working on the exchaneg server, which i dont really know! as they have to be the same in order to allow for the connection.
i was looking for the opposite to open the ports in the router.

Similar Messages

Exchange Server 2013 Service Pack Upgrade - Outlook connectivity issue

Hi,
After upgrading to Exchange Server 2013 service pack 1, we are unable to connect via Outlook 2010 or Outlook 2013. Outlook Web Access is working fine though. We have followed all the instructions, and have applied Outlook upgrades, but the issue remain the
same. Outlook was working fine before the upgrade.
Have we missed out something. I would highly appreciate if someone can help out? I'm not sure if this is the known issue as I can't seem to find anything on the internet.
Already applied the transport fix.
Thanks in advance!

Hi,
According to your description, your Outlook 2010 and Outlook 2013 come across the connectivity issue.
To narrow down the issue, I’d like to recommend the following troubleshooting:
1. Check if the issue happens on all Outlook users
2. Check the Outlook Anywhere connectivity by using ExRCA:
https://testconnectivity.microsoft.com/
Additionally, MAPI over HTTP is only supported when you use Outlook 2013 sp1 and Exchange 2013 sp1 at the same time. Since the issue also happens on Outlook 2010 client, we can firstly try the above troubleshooting.
If you have any question , please feel free to let me know.
Thanks,
Angela Shi
TechNet Community Support

Issue with hostname "localhost" and general CR connectivity issue

Hello,
we installed SAP BOE with the integrated Tomcat 6. We used a Web Tier installation on the same host, but in different paths.
Tomcat was installed under /usr/sap/tomcat/sap_bobj/tomcat and the SAP BOE package under
/usr/sap/XXX/sap-bobj/enterprise_xi40. The host has two IP addresses, a physical address (A) and a logic address (B).
We want to get a setup that uses the logical address whenever possible.
We have issues with Crystal Reports for Enterprise XI4.0.
When CR ist started from the BI launch pad, then CR ist started and tries to connect to "localhost". The hostname "localhost" is communicated from BI launch pad to CR.
For sure, no communication with "localhost" is possible.
When CR is started manually and a connection to the respective Tomcat server is initiated (port 8080, servername B, context /dswsbobje) we get the
error message. please wait, no connection possible at the moment. I already read and applied SAP KB articles 1598906 and 1601997, but the issue is not solved.
1- Where I can make changes so that BI launch pad will communicate hostname B and not "localhost" to start CR?
2- Is there any local log file on the PC to check why CR can not connect, when started manually?
Best regards Bernd

we have installed BO 4.0 and Its working perfectly. we have using webi reports,
As next step recently we have installed Crystal reports for exterprise XI4.0
But we could not connect with BO server. Please guide us on below req..
Server name:
Server Port No :
Server COntext :
System Display Name :
User Name :
Authentication Type :
Thanks
Pari

Activation failure - Requesting I need to activate Photoshop CS5.1 despite having done this previously & used Photoshop. Adobe can't connect to internet to activate, yet program is allowed through Firewall and not having connectivity issues through Browse

Hi,
I currently have Photoshop CS5.1 on Windows 7 (64 bit) and it's now requesting I need to re-activate it, despite having already done this with a serial number when I installed it and even used the program numerous times.
I get a screen saying "Product activation is required" but every time I try to activate it, it says there was a connection issue and asks me to connect to the internet.
I've checked my firewall settings and Adobe is allowed through. No connection issues using my Browser, Skype etc.
Anyone got any solutions?
Thanks,
Westy

Sign in, activation, or connection errors | CS5.5 and later

WLC 4400 (SW ver: 7.0.235.3) and 1242 AP connectivity issue

Hi ALL..,
I got the problem with WLC and APs, APs cannot get IP and can't connect to WLC, it show folloing error,
*Oct 24 14:45:27.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.2.11 peer_port: 5246
*Oct 24 14:45:28.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Oct 24 14:45:29.419: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.2.11 peer_port: 5246
*Oct 24 14:45:29.420: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.2.11
*Oct 24 14:45:29.420: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Oct 24 14:45:29.595: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*Oct 24 14:45:29.602: %DTLS-5-ALERT: Received WARNING : Close notify alert from 192.168.2.11
*Oct 24 14:45:29.602: %DTLS-5-PEER_DISCONNECT: Peer 192.168.2.11 has closed connection.
*Oct 24 14:45:29.602: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.2.11:5246
*Oct 24 14:45:29.661: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 24 14:45:29.661: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 24 14:45:29.756: status of voice_diag_test from WLC is false
My Management Int IP : 192.168.2.50
AP Mangement interface :192.168.2.11
DHCP server Pri : 192.168.2.12 Sec 192.168.2.13
There are reachability betweent SW and WLC. Do you have any idea about my issue?
Thanks and Regards
CSCO11872447

It seems your LAP AP is not getting the iP of the management subnet and LAP is in different subnet than your management IP.
Please try keeping the static IP on the LAP and then try joining it to the controller first and later on keep it on the DHCP.
when AP is plugged into a switch, the switch port needs to be access with the right VLAN allowed

Apple TV and Drop Outs, Connection Issues

I use AppleTV to mirror my ipad 2. it's great. Love it Then I'll try it again and it may work but often the icon disappears. I then clear the password then re-enter it and that will bring it back or if that doesn't work I may have to shut down my ipad 2 at least once.
This happens almost every second or third time I try to use it.
I currently have an iphone 4s, ipad2, ipod touch and as someone has said before, this is the first time I've been deeply disappointed in an Apple product. I expect glitches every now and then but this continual drop out and connection issues I have is beyond the joke.
Does anyone have any solutions. Yes I have done all the updates, yes I am on the same network, yes airplay is turned on, yes home sharing is enabled.
As you can see I am peeved!

I too am having the same problem. I have a MB Pro running OS X 10.9.4 cannot see AirPlay option. Any solutions out there? Tried AirParrot but it is spotty at best.

TS1398 Ever since I upgraded to iOS 7.0.4 my wifi strength is very weak and I have connection issues all of the time.

I upgraded my iPad 3 to 7.0.4 and now I have wifi issues I never had before and apple customer support is no help. Does anybody know how to solve this issue?

Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
Fix WiFi Issue for iOS 7
http://ipadnerds.com/fix-wifi-issue-ios-7/
Fix WiFi Issue for iOS 7
http://ipadnerds.com/fix-wifi-issue-ios-7/
iOS 6 Wifi Problems/Fixes
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Boost Your Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
Troubleshooting a Weak Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
10 Ways to Boost Your Wireless Signal
http://www.pcmag.com/article2/0,2817,2372811,00.asp
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
Some Wi-Fi losses may stem from a problematic interaction between Wi-Fi and cellular data connections. Numerous users have found that turning off Cellular Data in Settings gets their Wi-Fi working again.
You may have many apps open which can possibly cause the slowdown and possibly the loss of wifi. In iOS 4-6 double tap your Home button & at the bottom of the screen you will see the icons of all open apps. Close those you are not using by pressing on an icon until all icons wiggle - then tap the minus sign. For iOS 7 users, there’s an easy way to see which apps are open in order to close them. By double-tapping the home button on your iPhone or iPad, the new multitasking feature in iOS 7 shows full page previews of all your open apps. Simply scroll horizontally to see all your apps, and close the apps with a simple flick towards the top of the screen.
Wi-Fi or Bluetooth settings grayed out or dim
http://support.apple.com/kb/TS1559
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

WRT54GS V4 with Mac - connection issue!

Hi,
I have a WRT54GS wireless router of version 4.
It has 3 PCs (one desktop, wired, 2 laptops, wireless), 2 iPhones and one Mac connected to it.
All PCs and iPhones are working fine and get good signal and stable connection.
The one Mac, however, can't seem to make it...
The connection keeps dropping and when I try to conect again I get a connection timeout (-6). After few attempts I, most of the time, are able to connect and get very good signal, until the next time it dropps.
Things I already tried so far:
I updated the firmware to the latest one, from the Linksys support site.
I resterted the router few times as well as the Mac.
I changed the channel (from 6 to 9).
Help... Please...
Thanks,
Message Edited by Radzi on 10-27-2008 01:36 PM

DIdn't help...
Tried changing to WEP, removing security completely, all kinds of tricks, including, now, chnging the MTU from 1500 to 1350.
No luck.
The odd part is that I sometimes get a signal and then it is very strong and fast. Few minutes (best case) later it starts losing the connection quality to complete drop.
I, then, get on the Mac "connection timed out" message.
I start getting very tired of this. Look slike I will give up soon and buy something else.

OutlookProvider EXCH/EXPR questions for 2007/2013 CoExistence, Outlook connectivity issue

Hi Everyone-
Can anyone give me advice on how to configure my Outlook providers for my environment?
Single 2007 Server in coexistence with separate CAS/MBX 2013 Sp1.
It currently looks like this:
I changed the EXPR CertPrincipleName after coexistence due to a cert pop-up that was occurring in Outlook (2010) while connected to a 2007 mailbox.
All connectivity and mail flow is working fine, EXCEPT, connecting Outlook to a 2013 mailbox. It finds the user/mb but fails at login.
Thank you for your time!

Hi Andrew
There is nothing much complicated to think if we use Exchange Server Deployment assistant as it an perfect guide.
http://technet.microsoft.com/en-US/exdeploy2013/Checklist?state=2419-W-EgBEAgAAQAAAAQECAQAAAAg%7e
To allow your Exchange 2013 Client Access server to redirect connections to your Exchange 2007 servers, you must enable and configure Outlook Anywhere on all of the Exchange 2007 servers in your organization.
Users with mailboxes still on 2007 will be connecting to CAS 2013 and then will be proxied to CAS 2007
Exchange 2013 will coexist easily with 2007 mailboxes by using ActiveSync. As soon as the DNS entry for 2007 CAS points to the 2013 Client Access Server, 2007 mailboxes that use ActiveSync will be able to sync through the 2013 Client Access server without
any configuration changes. This is assuming that if the 2007 CAS Servers are using a default configuration such as SSL (443) with basic authentication. Integrated authentication by default should remain enabled on the Proxy folder that is located beneath
the Microsoft-Server-ActiveSync Folder.
During coexistence the 2013 OAB will be the default OAB.Run below command to check
get-mailboxdatabase | fl identity,*offline*
Run below command to change Activesync virtual directory
Get- ActiveSyncVirtualDirectory –Server “Exchange 2013 ServerName” | Set-ActiveSyncVirtualDirectory -InternalUrl "https://abc.com/Microsoft-Server-ActiveSync" –ExternalUrl "https://abc.com/Microsoft-Server-ActiveSync"
Run below command to change the autodiscover url
Get-ClientAccessServer –Identity “2013 Server name” | Set-ClientAccessServer –AutodiscoverServiceInternalUri “https://abc.com/autodiscover/autodiscover.xml”
Remember to mark as helpful if you find my contribution useful or as an answer if it does answer your question.That will encourage me - and others - to take time out to help you

Contribute 3 and Dreamweaver 8 Connection Issues

Hello,
I'm having issues finalizing my site definition at the
"Contribute" stage in Dreamweaver.
When I test the connection from Dreamweaver's "Remote Info"
stage, Dreamweaver successfully connects to the main directory: "
http://domain.edu" (domain.edu), where
I upload files to the main site (not connected to Contribute), but
I want to connect contribute to a mini site in a subdirectory of
the main site - "
http://domain.edu/folder/folder".
I'm stuck at the point where I click "Administer Site in
Contribute" in the "Site Definition" dialog box. This is the first
time I've set up a site in Dreamweaver with Contribute
compatibility and a remote connection, so I have not run into this
before.
Everything was going fine until the "Contribute" panel.
The Site root URL in the dialog box originally pointed to the
index file of the existing mini site sitting on the server: "
http://domain.edu/folder/folder/index.htm".
When I click the "Test" button, I keep getting the error
message:
"Dreamweaver could not connect to the remote server... Please
fix the remote connection before continuing"
So, I changed the Site root URL to point to the root folder
of the mini site:"
http://domain.edu/folder/folder/index.htm"
Then I got this error message:
"Dreamweaver could not find a page at the specified site root
URL"
I changed it back to the original URL and went back to the
"Remote Info" dialog. I thought that maybe the problem was that I
was supposed to change the host directory to "domain/folder/folder"
(from "domain") to reflect the exact folder that the mini site was
stored in, but when I did, I got an access denied error.
I am at a complete loss, please help...
I am using:
Dreamweaver 8
Contribute 3
Windows XP
Has anyone gotten an answer to this problem? I have seen many
threads in both the Dreamweaver and Contribute forums, but nothing
looked like a solution or explanation of why this occurs. Please
Help. I would like to use this tool throughout our college
campuses, but I am loosing faith in this product. I know that If
I'm having trouble, novice users will completely reject this
technology...
-Ena

OK, Now I'm REALLY confused
I gave up on trying to connect Contribute to my website
through Dreamweaver. I figured I'd go back to Contribute and see if
I could get the connection directly from Contribute. Somehow, It
worked. I think I went to Edit > My Connections > Create...
> and entered my FTP information and it worked! I still cannot
connect through DW however.
So far, this has allowed me to continue with setting up this
site with Contribute. I'm still really confused as to what the
problem is with Dreamweaver and Contribute working together.
I'm going to go back and make sure that I can repeat whatever
I did to get it working. The only thing worse than not being able
to get something to work is stumbling upon the solution and not
knowing how you did it
-Ena

Exchange 2010 not 13 and outlook connection issue

We have 2 Exchange servers in DAG w/o DAC in different sites and while creating a profile in Outlook client it is only able to see one or the other site. So I cannot have a profile for site P(rimary) and another for site S(econdary).
So, prior to moving the mailbox affected between MailboxDB it would only allow the Outlook client to connect to site S, after moving it now it works only for site P
OWA works fine but if I try to add one profile for user A pointing to mail1.domain.local and in the control panel > mail > mail setup > Profiles > Show Profiles I click on add, create a new profile > name it mail1 > choose manual setup >
and microsoft Exchange server > in server Settings I add mail1.domain.local click on check name and it maps the account to mail2.domain.local on a remote site.
I may have failed to explain this issue, if so please feel free to request more info.
I have a feeling the issue might not even be with Exchange but AD.
Thanks for any input.

Hi,
Based on your description, the server change automatically when you try to configure different Outlook profile.
Is it always changed to mail2.domain.local when you input mail1.domain.local?
Did this appear every time you create Outlook profile?
Please check if the server name you set is in the site where the active database resides.
Best regards,
Belinda Ma
TechNet Community Support

IPhone 6 and Bluetooth phone connectivity issues with my vehicle: this is how I fixed it.

With so many threads on this topic, I wanted to detail the steps I took to fix my iPhone 6 Bluetooth issues regarding connectivity to my vehicle and handsfree calling. My phone was pairing with my vehicle without a problem and syncing my contacts and call history but when I attempted to make a call (from either the phone or the vehicle screen) the audio went out and I could not hear the call either through the vehicle speakers or on the phone. The call was going through but I was unable to see it on my vehicle screen and/or hear it either the phone or the vehicle screen.
Based on my research and what I have learned so far, the people having problems are those who restored their new iPhone 6 from an iCloud backup from a previous phone, rather than setting up their iPhone 6 as a new phone. I did an iCloud restore from my previous 5s running iOS 8.
First, I am a Verizon customer and I enabled Advanced Calling on my line. After I requested that this feature be added to my line, under “Cellular” settings on my iPhone, I enabled LTE voice & data.
Next steps:
1) Unpair/remove iPhone from the vehicle;
2) Forget/remove the vehicle from the phone Bluetooth settings;
3) Soft reset the iPhone;
4) Reset network settings on the iPhone; and
5) Pair the phone to the vehicle again and attempt to make a call.
If that does not work…
6) Perform a factory reset, erasing EVERYTHING from your phone and set it up as a new iPhone rather than restoring from a backup.
Resetting the network settings seems to be working for some people. It did not work for me. I tried it a few times with no result. I did the dreaded factory reset, paired the phone with my vehicle and had all of my Bluetooth functionality back and was able to use the handsfree phone with zero issues.
I was on the phone yesterday multiple times with Apple, Toyota Entune, Verizon and my Toyota dealer. Verizon blamed Toyota Entune, Toyota Entune blamed Verizon and my Toyota dealer blamed Apple. Nobody had a clue how to fix this issue or what was causing it. I don’t know the exact reason why the previous iCloud backups are killing the Bluetooth connections, I just know what worked for me and I thought it was worth sharing.
Good luck.

The new 8.0.2 update DID NOT FIX THIS ISSUE AT ALL. After you power off and on with the phone, same issue as the 8.0, all 3 of my cars lost Bluetooth connection and shows no signal at all. Good job Apple, what a lousy update you guys did.
2011 Lexus ES350
2011 Subaru STI
2012 Mercedes E350.

UML295 and Lenovo X1 connectivity issues

I have a UML295 and I'm attempting to use it with Lenovo's X1 Carbon (Model 20A) and I'm having some serious issues. Well, my end user is. After a restart, card is inserted and works perfectly. I don't need to open up the MBB software, anything. If I disconnect or just remove the device and wait a few minutes to plug it back in, it doesn't' work. Indicator light turns green, flickers, etc. No internet. I open up the MBB software and shows I'm connected but doesn't go anywhere, or the software doesn't recognize that the card has been inserted. It displays this behavior on multiple X1 Carbon machines that I have here. I've tested it on an older T530 Thinkpad and it works as intended. No need to install the MBB software neither. As soon as the indicator light turns green, I'm good to go on internet access.
Is there a firmware update or a known issue between these cards and the X1 Carbon? It's frustrating to our reporters that they can't use their new laptops out in the field.
Thank you

USB modem devices need both drivers and connection software to facilitate a connection to the VZW network. I suggest going out and downloading the latest of both from VZW and retesting on your machine.
UML295 download:
http://www.verizonwireless.com/support/knowledge-base-72600/
Otherwise the problem that you mentioned here is specifically resolved by use of a Jetpack. No drivers, no software. All users need is normal WiFi and they will be able to access the internet just like at any other hotspot. This was a big advantage for us in addition to the reduced hardware costs of broken USB ports on laptops and USB modems.

Have you been getting timeouts and other weird connection issues lately?

Internet connection has become a bit wonky as of late, have you been experiencing some or all of the following symptons?
1) Most internet speed test sites just stop before completing as if they have timed out (i.e. speedtest.net).
2) Sites will start loading quickly but then sometimes randomly stop and have to be manually refreshed.
3) Downloads will randomly stop downloading for some moments before resuming (particularly from Steam)
4) Tracert to some websites that were causing issues show timeouts on peering with Alter.net servers.
Looks like there are some issues between Verizon and Alter.net (formerly MCI, now Verizon owned) in NY.... Any word on when we can expect a resolution? This is quite frustrating as it affects a good amount of traffic.

I'm a little further east than you out here on Long Island, Touyats, but I've seen none of the issues you or the Original Poster here are experiencing.
Assuming you're having the problems on a device connected to your router by Ethernet cable (WiFi opens up an entire range of other possible problems) you might try getting your router assigned a new WAN IP address.
If you want to give that a try, see this post for the steps involved:
http://forums.verizon.com/t5/FiOS-Internet/How-am-I-able-to-change-my-ip-address/m-p/703336#M47733

I bought the iPhone 6 yesterday and am having connectivity issues

I bought the iPhone 6 yesterday and over the course of the last 26 hours, I've had issues with my phone connecting to data coverage. I can make phone calls and send texts but my most used apps (Gmail, Facebook, Twitter, even the App Store) won't load because they can't connect. Shutting down and restarting the phone has resolved the issue but I don't think that's a suitable resolution long-term. The phone does display that I have 3 bars (or dots in the case of the iPhone 6) and shows "LTE" but the phone doesn't actually connect. Any suggestions/help? Thanks.

Krallas,
That is very strange behavior for this new phone to have, but don't worry, ok? We'll help you get it fixed. Please go ahead and turn the phone all the way off. Then remove the SIM card for at least 30 seconds, replace it, and turn the phone back on. That may just do it for you!
SarahO_VZW
Follow us on Twitter @VZWSupport

WRT54GS and MS Outlook connectivity issue

Similar Messages

Maybe you are looking for