1131 access point, broken flash?

I have had two 1131 access points die in the last few weeks, both with the same symptoms. I suspect both have broken flash systems and are due for the bin. If anyone can offer any confirmation or a way to fix it, I would be grateful.
On booting, it gives the following error:
Xmodem file system is available.
flashfs[0]: unable to allocate available block.
The system has been interrupted, or encountered an error
during initializion of the flash filesystem. The following
commands will initialize the flash filesystem, and finish
loading the operating system software:
    flash_init
    ether_init
    tftp_init
    boot
ap:
Trying to wake up the flash:
ap: flash_init
Initializing Flash...
flashfs[0]: unable to allocate available block.
...done Initializing Flash.
ap: dir flash
unable to stat flash/: permission denied
I have tried the standard recovery mode of uploading a new firmware via TFTP, but I can't even set variables:
ap: set IP_ADDR 10.0.0.1
flash:/env_vars.tmp: invalid argument
The filesystem containing the variables may not be initialized yet.

Thanks for the tip, however I should probably have said the access points are autonomous, so the method you suggested will not work.
Yes it does.
You need a two-step method.
Your AP is booting up with either no IOS or a corrupt IOS.
1. In order to efficiently transfer the IOS to an AP that has no IOS you need to use the process I've posted earlier.
2. Once the AP boots up in autonomous mode, it's as easy as giving the BVI1 an IP address and use the command "copy tftp: flash:" to transfer the LWAP/CAPWAP IOS to the AP.

Similar Messages

Document on 1131 Access point

Please provide the documentation to configure 1131 Access Point.
We are getting documentation for 1130 and not for 1131.
Help wouldl be highly apprecited.

Hi Navinder,
It's the same. 1130 is the generic model number while 1131/1132 is a specific model number.

1131 ACCESS POINTS BOUNCING

I have a site with Lightweight 1131 access points, with 5508 WLC's in HA running Code 7.4.110. In 2 areas of one site the access points are bouncing, I have attached the logs from one of the AP's at the site. The switch that the AP's are connected to is a WS-C3750-24P SW VERSION: 12.2(55)SE1. This has only happened in 2 areas on the site, and only 24 Access Points out of 335. HELP!!!!!!

Hi Scott
I have 184.2 Watts remaining on the switch. I have just come back from site having tried the following:
1. Took and AP from another site, this worked.
2. Bounced the Access Points to a controller still running 7.3.101.0 this also worked.
3. Bounced the Ap's back to their local controller, they went back to not functioning correctly.
We upgraded to Code 7.4.110 it was an,assured, tested version from Cisco, to fix other issues we had. Any help would be welcome.

Cisco module controller & 1131 access-point

I'm using a blade as a controller in a cisco router. trouble is it does not see
the 1131 access-points. does see 1020 access points. Any thoughts

If you are using OP 43 to tell the access points where to find the controllers you will need a new entry for the 1130 series of access points.

Cisco 1131 access point status led

Hi
Any one experienced a white light on the status led, its the "ring light" infront of the AP. ive checked on http://www.cisco.com/en/US/docs/wireless/access_point/1130/installation/guide/113h_c4.html where all colours are listed and none point done to white.
ANy ideas?
Thanks

Here's an update on this issue. I have had about a 2% failure rate on my 3502i's due to blue, green, and white light freezing. We sent several unit to Cisco's wireless engineer team in Richfield. They have found the issue and have written a fix and are currently doing testing this weekend. They are sending a senior wireless engineer to my office on Monday morning to apply the fix on the 200 units that we have yet to deploy. This is the bad part: the fix can only be applied through the console port and they won't have this integrated into a controller code until May/June. The good news is they have a fix or will just RMA with no questions. I have a webex with their wireless team to explain exactly what the issue is, but from what I gathered is something to do with the boot loader image and the IBM chip in the unit. I will follow up with you guys on Mon/Tues.
Sent from Cisco Technical Support iPhone App

602-OEAP Access Point broken after WLC upgrade to 7.4.100.0

Hey all,
I have a TAC case open, but it doesn't seem to be making any progress....
I upgraded my 5508 controller from 7.2.111.3 up to 7.4.100.0
Most of my APs are fine. 3500s, 1100s etc.except for 602i APs. The APs associate, they update software etc, but they won't broadcast the WLAN.
An interesting thing, on the 602 AP, in the log, I see this:
*Mar 06 15:08:12.667: SSID remote, WLAN Profile Name: RemoteOEAP, added to the slot[0], disabled
So the AP is definately talking to the WLC and being pushed the correct WLAN profile.
Another thing I noticed:
On the controller, the AP shows the the Admin status of the radios is showing DOWN, but the Admin status on the AP itself shows UP
I've done a factory reset on the APs to no avail. I have a 2504 WLC as well that i'm in the process of implementing in a DMZ specificially for these APs, and for testing purposes, I associated the 602 Ap to that WLC as well. This one is running 7.4.100.0 too, same results. It would appear to be a problem with this version of software?
Anyone else had this problem?

Hey, thanks for taking a look at this. Unfortenately, that's not the issue in this case. The AP is set to "United States" and the WLC is only configured for US. Just so I'm looking in the correct place:
On the AP in the WLC, it's under the "Advanced" tab
On the WLC, its under Wireless -> Country correct?
The frustrating part is that the 600 really doesn't have anything that can be configured on it, which means troubleshooting is also limited.

1131 access point intermittently stops responding

We have an 17 offices with the same basic wireless config. 2 or 3 ap's with the same configuration on them. This one particular office has 2 ap's that intermittently will stop responding to pings and are no longer reachable via telnet or http and users cannot connect through the ap. We are running c1130-k9w7-mx.124-3g.JA1/c1130-k9w7-mx.124-3g.JA1.
I had the site (located in Spain) send me pics of the ap's and noticed that they are not mounted, just laying on ceiling tiles in a plenum ceiling.
Once the ap's are again reachable there is nothing in the log that would suggest there was a problem and the ap does not reboot.
Any ideas?
here is the config...
ap1_spain#sh run
Building configuration...
Current configuration : 6901 bytes
! Last configuration change at 17:23:30 +0200 Tue Sep 14 2010 by dguse
! NVRAM config last updated at 17:23:30 +0200 Tue Sep 14 2010 by dguse
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec localtime show-timezone
service password-encryption
hostname ap1_spain
aaa new-model
aaa authentication login default group tacacs+ none
aaa authentication login no_aaa none
aaa authorization console
aaa authorization exec default group tacacs+ none
aaa authorization exec no_aaa none
aaa authorization commands 15 default group tacacs+ none
aaa authorization commands 15 no_aaa none
aaa accounting exec default start-stop group tacacs+
aaa accounting commands 15 default start-stop group tacacs+
aaa session-id common
resource policy
clock timezone +0200 2
ip subnet-zero
dot11 ssid xxxxxxxxx
   authentication open
   authentication key-management wpa
   wpa-psk ascii 7 03055908555ABA1A1A5F4D071616
dot11 network-map
power inline negotiation injector 0017.0ed7.442f
crypto pki trustpoint TP-self-signed-1171819700
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1171819700
revocation-check none
rsakeypair TP-self-signed-1171819700
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers tkip
ssid linvatec
power local 14
power client 14
station-role root
world-mode dot11d country ES both
no cdp enable
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
encryption mode ciphers tkip
dfs band 3 block
channel dfs
station-role root
no cdp enable
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
speed 100
full-duplex
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 10.x.x.x 255.255.255.0
no ip route-cache
ip default-gateway 10.x.x.x
no ip http server
ip http authentication aaa login-authentication default
ip http authentication aaa exec-authorization default
ip http authentication aaa command-authorization 15 default
ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
snmp-server view dot11view ieee802dot11 included
snmp-server community xxxxxxxxxxxxxx RO
snmp-server location Barcelona
snmp-server chassis-id ap1_spain
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps tty
snmp-server enable traps entity
snmp-server enable traps disassociate
snmp-server enable traps deauthenticate
snmp-server enable traps authenticate-fail
snmp-server enable traps dot11-qos
snmp-server enable traps switch-over
snmp-server enable traps rogue-ap
snmp-server enable traps wlan-wep
snmp-server enable traps config-copy
snmp-server enable traps config
snmp-server enable traps syslog
snmp-server enable traps cpu threshold
snmp-server enable traps aaa_server
tacacs-server host 10.x.x.x
tacacs-server directed-request
tacacs-server key 7 071C244F5B461C1D0D1079282A2D27222D010C
bridge 1 route ip
line con 0
authorization commands 15 no_aaa
authorization exec no_aaa
login authentication no_aaa
line vty 0 4
sntp server 10.x.x.x
sntp broadcast client
end

Hi,
     What is the switchport config of the port connected to the AP? The AP is set to be 100/Full, if the switch isn't set as well, you could be going half-duplex and losing connecitvity due to that.

WLC 5508 and remote site (DMVPN) Access Points

Hi All,
We just purchased a WLC 5508 and would like to know if it will control remote VPN site Access Points. Here are the details:
The 5508 will live at our home office. We have multiple remote sites that are connected via Cisco's DMVPN. Each site has one Cisco 1131 Access Point hanging off of either a Cisco 1841 or a 2811 that is using DMVPN back to the home office 2811. Can the 5508 manage the remote Access Points?
Thanks for your help guys!

Are you are talking about OfficeExtend?
Cisco OfficeExtend
https://www.cisco.com/en/US/solutions/collateral/ns340/ns517/ns430/solution_overview_c22-523307_ns348_Networking_Solution_Solution_Overview.html
OfficeExtend supports 1130 & 1140 as long as you have the Wireless PLUS (WPLUS) Software.
OfficeExtend Access Point
http://www.cisco.com/en/US/docs/wireless/wcs/6.0/configuration/guide/6_0apcfg.html#wp1069890

The connection between your access point, router, or cable modem and the Internet is broken.

At random points throughout my laptop usage, I randomly disconnect from the internet and receive these 2 messages:
1. The connection between your access point, router, or cable modem and the Internet is broken.
2. The default gateway is not available.
It fixes the issue for a short period of time, but constantly happens. This is really starting to annoy me. I have no problems on any other internet, and other people i live with are connected with no issues to the internet. I have tried a number of solutions
online that has "worked" for others to no success such as resetting the router, fooling around with command prompt, and changing the performance settings to not drop internet when low on power. Does anyone have a solution for my technical problems?
I am running Windows 8.1 on a Lenovo ideapad that is less than a year old. I will be honest I am not a very knowledgeable person when it comes to computers, so please use simplified explanations.

Checked this ?
http://answers.microsoft.com/en-us/windows/forum/windows_7-networking/window-networking-troubleshoot-error-the/c130ede9-757e-4224-9ae8-3cceb82eeb74
Arnav Sharma | http://arnavsharma.net/ Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading
the thread.

Bridging with 1131 Ag series access point.

Hi,
I want to use 1131 AG series access point for bridging between two buildings which are 20 metres apart from each other.
Is it possible and what are the limitation for this design?
Please help.
thanks in advance.
Pulkit Sharma

Hi Pulkit,
The autonomous 1130AG series access point supports these operating wireless modes:
? Root access point?Connected to a wired LAN and supports wireless clients.
? Repeater access point?Not connected to a wired LAN, associates to a root access point, and supports wireless clients
? Workgroup bridge?Not connected to a wired LAN, associates to a root access point or bridge, and supports wired network devices.
As this unit was not designed to be use outdoors, having a clean RF line of sight is really difficult. To be honest I do not think this unit was designed to connect two remote buildings even if the units are indoors. I would look for APs with detachable antennas like the 1242AG or the 1200 modular series so you can use external antennas and bridging roles.
Hope it helps,
Roger Carpio.

Access point are not coming up after upgrade image of WLC

Hi,
I have AIR-WLC4402-50-K9 WLC i that current IOS is 7.0.98.218 and i upgraded with 7.0.116.0 IOS but after upgrading and reboot the WLC from 15 access point 3 access point are not coming up and 12 are coing up and working fine (4 1142 and 11 1131 series access point) 3 which are not coimg is 1131 series access point. when i login with console to 3 access point its rebooting 2 times and coming on ap: prompt.
In between that i reloaded the WLC one more time because from 15 acess point only 4 aceess point are came up and i also cleck the show boot on wlc its output is
7.0.116.0 (default)
7.0.98.218 (active)
so i reload the wlc and checked out of 15 acess point now 12 acess point are up and still 3 are not. And i also checked the output of show boot command its
7.0.116.0 (default)(active)
7.0.98.218
So i things its because of when 2nd time i reload the wlc the remaining 3 access point are getting image from wlc but because of reload its connection should be loss and error loading flash error are coming on acess point.
After that i recover the IOS for access point and convert into autonomus and from autonomus convert into Leightweight Access point. I also attached the procedure for recover the ios of access poing
But my question is why this 3 access point are not coming up is this happen's after upgrading wlc can any one please send me Step by Step WLC S/W Upgrade' process and if this this happens some time please send me any doccument related to this.

Sunil,
When you rebooted the controller did you do it from the Web GUI, the CLI, or did you physically reboot the controller? I believe and maybe incorrect but if your getting the ap: < prompt > that means that there is no firmware on the unit. If you have restored these to functioning autonomous unit and then re-converted them to Lightweight and it's still happening then we need to look at a debug output of what is happening when those AP's attempt to join the controller.
The capture you attached shows that it appears to join the controller and get a config, but are you saying that when it reboots again it stops working?? the other thing I would reccomend is clear out the flash memory since your capture shows the possibility that there are several copies stored there.
Hope this helps.

Access Point 1231

Good evening,
I am contacting you for consultation, at our facilities are mounted Access Point Model 1231 and Model 1242, which are connected to omni-directional antennas, these antennas might suffer vandalism or theft, as I learned that I have broken this antenna, there is some kind of log or alarm to tell me to my Access point that has no antenna, I put the case for both Access Point Access Point centralized and autonomous.
Thank you very much

My other one shown:
NAME: "AP1210", DESCR: "Cisco Aironet 1200 Series Access Point"
PID: AIR-AP1231G-E-K9    , VID: B0 , SN: FCZ0906Z0AK
cisco AIR-AP1231G-E-K9     (PowerPC405GP) processor (revision B0) with 15138K/1236K bytes of memory.
Processor board ID FOC09030GAC
PowerPC405GP CPU at 196Mhz, revision number 0x0145
Last reset from power-on
1 FastEthernet interface
1 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:13:1A:22:B7:9F
Part Number                          : 73-8704-08
PCA Assembly Number                  : 800-23211-09
PCA Revision Number                  : A0
PCB Serial Number                    : FOC09030GAC
Top Assembly Part Number             : 800-23304-08
Top Assembly Serial Number           : FCZ0906Z0AK
Top Revision Number                  : A0
Product/Model Number                 : AIR-AP1231G-E-K9
Configuration register is 0xF
Can Fix this, to correct use?
thanks
R. Kuhn

Aironet 350 Access Point needs security

I have been asked to help a fledgling school lock down their wireless network. The network is currently setup as 3 Aironet 350 Access Points with operating on the same subnet distributed around the school.
These have NOT been updated or touched since the day they were installed, by all acounts. I think they are running VXworks. My issue is that most support links that might prove helpful seem to be broken.
A few simple questions:
Can the Aironet 350 be secured and then used with a simple shared key? This link seems to say no, that you must have Cisco software on the user computer as well. that certainly can't be right, can it?
I'm clearly out of my comfort zone with these, but they just don't have anyone to do this for them. It looks like they need to be flashed to IOS and then able to use WPA but not WPA2? I'm having trouble finding a firmware lik for the 350 as well because it's EOL.
Basically, any help or information is welcome! I'm ready to just pull the plug on them and call them secure!

350 APs (not bridges) can be converted to IOS. Then they can do WPA-PSK TKIP. Downside is they only have 802.11b radios. The latest IOS they can run is old but could probably be setup with WDS using an internal RADIUS server on one.
The upgrade tool and image are still available for download. I'm attaching a .pdf of instructions.
You need these files:
Aironet-AP-Cisco-IOS-Conversion-Tool-v2.1.exe
AP350-Cisco-IOS-Upgrade-Image-v2.img

Prompt never appears in a 2602i access point

Hello:
Today I converted an AIR-CAP2602I-A-K9 access point to autonomous using the mode button/tftp method, but no matter what IOS I install (I tried 2 different IOS and also tried entering to Rommon - I am able to change IOS because the procedure I used does not need any command), i never get to see the prompt so that I can introduce commands to configure the AP. It's like it hangs after "succesfully" initializing
The only thing I can see all the time are "normal" console messages, and It shows no error message at all. It happened even before the downgrade.
This is where the AP stops, but it is not really hung because console messages could keep showing up. It just never gets to the promt so I can enter some commands. Would not even acept Enter.
Cisco IOS Software, C2600 Software (AP3G2-K9W7-M), Version 15.2(4)JA1, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Tue 30-Jul-13 23:12 by prod_rel_team
Initializing flashfs...
flashfs[3]: 200 files, 7 directories
flashfs[3]: 0 orphaned files, 0 orphaned directories
flashfs[3]: Total bytes: 31739904
flashfs[3]: Bytes used: 14286848
flashfs[3]: Bytes available: 17453056
flashfs[3]: flashfs fsck took 9 seconds.
flashfs[3]: Initialization complete.
flashfs[4]: 0 files, 1 directories
flashfs[4]: 0 orphaned files, 0 orphaned directories
flashfs[4]: Total bytes: 11999232
flashfs[4]: Bytes used: 1024
flashfs[4]: Bytes available: 11998208
flashfs[4]: flashfs fsck took 0 seconds.
flashfs[4]: Initialization complete.
Copying radio files from flash: to ram:
Copy in progress...CCCCC
Copy in progress...CCC
Copy in progress...CCCC
Copy in progress...CCCC
Copy in progress...CC
Uncompressing radio files...
...done Initializing flashfs.
Radio0 present 8764 8000 0 A8000000 A8010000 0
Rate table has 244 entries (64 SGI/104 BF variants)
Radio1 present 8764 8000 0 88000000 88010000 4
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-SAP2602I-A-K9 (PowerPC) processor (revision A0) with 180214K/81920K bytes of memory.
Processor board ID FGL1716S0Q6
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: BC:16:65:95:A7:C3
Part Number                          : 73-14588-02
PCA Assembly Number                  : 800-37899-01
PCA Revision Number                  : A0
PCB Serial Number                    : FOC17151DSW
Top Assembly Part Number             : 800-38356-01
Top Assembly Serial Number           : FGL1716S0Q6
Top Revision Number                  : A0
Product/Model Number                 : AIR-CAP2602I-A-K9
Press RETURN to get started!
*Mar 1 00:00:11.819: %IFMGR-7-NO_IFINDEX_FILE: Unable to open nvram:/ifIndex-table No such file or directory
*Mar 1 00:00:11.935: FIPS IOS test Image Checksum successful
*Mar 1 00:00:11.935: FIPS IOS test Crypto RNG DEK Key Test successful
*Mar 1 00:00:11.939: FIPS IOS test SHA-1 successful
*Mar 1 00:00:11.939: FIPS IOS test HMAC-SHA1 successful
*Mar 1 00:00:11.939: FIPS IOS test AES CBC 128-bit Encrypt successful
*Mar 1 00:00:11.939: FIPS IOS test AES CBC 128-bit Decrypt successful
*Mar 1 00:00:11.939: FIPS IOS test IOS AES CMAC Encrypt successful
*Mar 1 00:00:11.939: FIPS IOS test IOS CCM Encrypt successful
*Mar 1 00:00:11.939: FIPS IOS test IOS CCM Decrypt successful
*Mar 1 00:00:11.939: FIPS IOS test RSA Signature Generation successful
*Mar 1 00:00:11.939: FIPS IOS test RSA Signature Verification successful
*Mar 1 00:00:11.939: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:18.863: FIPS RADIO test AES 128-bit encrypt for TX on Dot11Radio 0 successful
*Mar 1 00:00:18.863: FIPS RADIO test AES 128-bit CCM encrypt on Dot11Radio 0 successful
*Mar 1 00:00:18.863: FIPS RADIO test AES 128-bit CCM decrypt on Dot11Radio 0 successful
*Mar 1 00:00:18.863: FIPS RADIO test AMAC AES 128-bit CMAC encrypt on Dot11Radio 0 successful
*Mar 1 00:00:18.863: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:24.991: FIPS RADIO test AES 128-bit encrypt for TX on Dot11Radio 1 successful
*Mar 1 00:00:24.991: FIPS RADIO test AES 128-bit CCM encrypt on Dot11Radio 1 successful
*Mar 1 00:00:24.991: FIPS RADIO test AES 128-bit CCM decrypt on Dot11Radio 1 successful
*Mar 1 00:00:24.991: FIPS RADIO test AMAC AES 128-bit CMAC encrypt on Dot11Radio 1 successful
*Mar 1 00:00:24.991: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar 1 00:00:25.007: initializing dot11 onplus
*Mar 1 00:00:25.259: not a autoconfig enabled device!!!
*Mar 1 00:00:27.039: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:28.039: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Mar 1 00:01:13.383: Starting Ethernet promiscuous mode
*Apr 12 07:12:42.000: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Apr 12 07:12:42.000: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Apr 12 07:12:42.003: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
*Apr 12 07:12:42.011: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2600 Software (AP3G2-K9W7-M), Version 15.2(4)JA1, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Tue 30-Jul-13 23:12 by prod_rel_team
*Apr 12 07:12:42.011: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a cold start
*Apr 12 07:12:42.991: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Apr 12 07:12:42.999: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Apr 12 07:12:42.999: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Apr 12 07:12:44.651: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed
*Apr 12 07:12:44.651: DPAA Initialization Complete
*Apr 12 07:12:44.651: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Apr 12 07:12:44.971: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up <--- CURSOR STOPS HERE AND WON'T ACCEPT ENTER OR ANY OTHER KEYBOARD ACTION
Any thoughts?
Best regards and thanks in advance

Leo, I'm usign SecureCrt, so I disabled XON/XOFF and DTR/DSR as usual, but was not disabling RTS/CTS, so I did and now it is working. Thank you very much!

Apple TV 2G (Airplay and Homesharing) can only stream from devices on the same wireless access point range??

connection:
40 Mbps Fiber Broadband connection using:
Devices:
1. Main Modem/router (AP1): Huawei HG8245 (provided by ISP) - Wireless enabled.
2. Remote Access point (AP2): Linksys/Cisco E3200 Wireless gigabyte router flashed with DD-WRT v24-sp2 (06/14/11) mini (Cascaded -wired- LAN to LAN from main modem).
3. Wireless Repeater to cover a dead spot (AP3): Linksys/Cisco E1000 wireless repeater.
4. Apple Tv (AT2G) with home sharing/airplay enabled.
5.( Ipad) with home sharing on itunes enabled.
6. Win7 (PC) using iTunes with Home sharing enabled.
all devices are updated to their latest firmware.
In order to cover a large 3 story house with Wifi. I had (AP1) is located on the first floor, while (AP2) is located in the basement floor directly wired by LAN to LAN with (AP1). (AP3) is located on the Ground floor away from the living room to repeat wireless network into the back yard. While (AT2G) is located in the living room on the ground floor right in the middle of both (AP1) + (AP2) while connected via Wifi.
Network SSID, security, passphrase and wireless settings of (AP2) are identical to (AP1) to create a single big LAN/WLAN roaming network where all devices connected to both wireless access points can find/share the others. As understood, it's refered to as bridging.
I have noticed that my iphone/ipad does not show the airplay button anywhere within the wireless network. it seems that the apple TV randomly choses to connect to the AP with stronger signal, or switch to the other in case of a reboot to one of them.
to elaborate further, if i was sitting in the living room (groundfloor), trying to airplay some you tube contents via Wifi to my Apple TV, i may not find the airplay button available all the time, i found out the reason is while i'm wirelessly connected to AP1, the Apple TV was connected to AP2 and both deviced cannot detect each others to enable my purpose. that goes the same for Home Sharing. only if my Ipad/PC and Apple Tv are on the same wireless AP. they would detect each others immediately.
although, the second AP (AP2) is suppose to extend my wireless network of the same subnet in which any device connected can be found.
After all sorts of trial and error tweaking my router/access point, I thought the problem would be due to the Linksys 3200 capability of bridging WLAN and lacks few protocols that enables my purpose. i have flashed the firmware to a DD-WRT, but again, problem was not solved.
I have not tried having my Apple Tv wired to either router/AP, but i assume it may work well if i do so. i still need to solve this wireless connection issue though.
Am i the only one with this problem, would there be something wrong with my setup?
Your feedback is highly appreciated.

You may or may not already have your network set up correctly, it's just that I can't tell from what you have said.
I have a main router provided by my ISP, I have several other Airport Extremes and Airport expresses connected by Ethernet, all set up to bridge the network created by the main router.
Each maker has their own settings, but bridging should be reasonably obvious. In simple terms my main router distributes IP addresses to all devices, the Airports bridge that network by passing these addresses to the devices from the main router. A base station that isn't in bridging mode will distribute its own addresses to the devices connected to it.
I don't really follow your next point.
instruction for configuration vary from manufacturer to manufacturer, the best course of action here is to refer to the manual. If everything is set up properly the addresses of everything on your network will have identical sets of numbers for the first 3 of 4 groups of numbers that make up an address, the last set must always be different. I think the part you are referring to with your DD-WRT is the option to have Ethernet and wifi bridged or not.
Some routers may be easier to configure than others, but generally speaking they should all work with the Apple TV. 5Ghz is less likely to suffer interference but it is much more likely to be blocked by solid objects, it may or may not be an advantage.

1131 access point, broken flash?

Similar Messages

Maybe you are looking for