1131 access point intermittently stops responding
We have an 17 offices with the same basic wireless config. 2 or 3 ap's with the same configuration on them. This one particular office has 2 ap's that intermittently will stop responding to pings and are no longer reachable via telnet or http and users cannot connect through the ap. We are running c1130-k9w7-mx.124-3g.JA1/c1130-k9w7-mx.124-3g.JA1.
I had the site (located in Spain) send me pics of the ap's and noticed that they are not mounted, just laying on ceiling tiles in a plenum ceiling.
Once the ap's are again reachable there is nothing in the log that would suggest there was a problem and the ap does not reboot.
Any ideas?
here is the config...
ap1_spain#sh run
Building configuration...
Current configuration : 6901 bytes
! Last configuration change at 17:23:30 +0200 Tue Sep 14 2010 by dguse
! NVRAM config last updated at 17:23:30 +0200 Tue Sep 14 2010 by dguse
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec localtime show-timezone
service password-encryption
hostname ap1_spain
aaa new-model
aaa authentication login default group tacacs+ none
aaa authentication login no_aaa none
aaa authorization console
aaa authorization exec default group tacacs+ none
aaa authorization exec no_aaa none
aaa authorization commands 15 default group tacacs+ none
aaa authorization commands 15 no_aaa none
aaa accounting exec default start-stop group tacacs+
aaa accounting commands 15 default start-stop group tacacs+
aaa session-id common
resource policy
clock timezone +0200 2
ip subnet-zero
dot11 ssid xxxxxxxxx
authentication open
authentication key-management wpa
wpa-psk ascii 7 03055908555ABA1A1A5F4D071616
dot11 network-map
power inline negotiation injector 0017.0ed7.442f
crypto pki trustpoint TP-self-signed-1171819700
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1171819700
revocation-check none
rsakeypair TP-self-signed-1171819700
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers tkip
ssid linvatec
power local 14
power client 14
station-role root
world-mode dot11d country ES both
no cdp enable
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
encryption mode ciphers tkip
dfs band 3 block
channel dfs
station-role root
no cdp enable
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
speed 100
full-duplex
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 10.x.x.x 255.255.255.0
no ip route-cache
ip default-gateway 10.x.x.x
no ip http server
ip http authentication aaa login-authentication default
ip http authentication aaa exec-authorization default
ip http authentication aaa command-authorization 15 default
ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
snmp-server view dot11view ieee802dot11 included
snmp-server community xxxxxxxxxxxxxx RO
snmp-server location Barcelona
snmp-server chassis-id ap1_spain
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps tty
snmp-server enable traps entity
snmp-server enable traps disassociate
snmp-server enable traps deauthenticate
snmp-server enable traps authenticate-fail
snmp-server enable traps dot11-qos
snmp-server enable traps switch-over
snmp-server enable traps rogue-ap
snmp-server enable traps wlan-wep
snmp-server enable traps config-copy
snmp-server enable traps config
snmp-server enable traps syslog
snmp-server enable traps cpu threshold
snmp-server enable traps aaa_server
tacacs-server host 10.x.x.x
tacacs-server directed-request
tacacs-server key 7 071C244F5B461C1D0D1079282A2D27222D010C
bridge 1 route ip
line con 0
authorization commands 15 no_aaa
authorization exec no_aaa
login authentication no_aaa
line vty 0 4
sntp server 10.x.x.x
sntp broadcast client
end
Hi,
What is the switchport config of the port connected to the AP? The AP is set to be 100/Full, if the switch isn't set as well, you could be going half-duplex and losing connecitvity due to that.
Similar Messages
-
Please provide the documentation to configure 1131 Access Point.
We are getting documentation for 1130 and not for 1131.
Help wouldl be highly apprecited.Hi Navinder,
It's the same. 1130 is the generic model number while 1131/1132 is a specific model number. -
I have a site with Lightweight 1131 access points, with 5508 WLC's in HA running Code 7.4.110. In 2 areas of one site the access points are bouncing, I have attached the logs from one of the AP's at the site. The switch that the AP's are connected to is a WS-C3750-24P SW VERSION: 12.2(55)SE1. This has only happened in 2 areas on the site, and only 24 Access Points out of 335. HELP!!!!!!
Hi Scott
I have 184.2 Watts remaining on the switch. I have just come back from site having tried the following:
1. Took and AP from another site, this worked.
2. Bounced the Access Points to a controller still running 7.3.101.0 this also worked.
3. Bounced the Ap's back to their local controller, they went back to not functioning correctly.
We upgraded to Code 7.4.110 it was an,assured, tested version from Cisco, to fix other issues we had. Any help would be welcome. -
Cisco module controller & 1131 access-point
I'm using a blade as a controller in a cisco router. trouble is it does not see
the 1131 access-points. does see 1020 access points. Any thoughtsIf you are using OP 43 to tell the access points where to find the controllers you will need a new entry for the 1130 series of access points.
-
1131 access point, broken flash?
I have had two 1131 access points die in the last few weeks, both with the same symptoms. I suspect both have broken flash systems and are due for the bin. If anyone can offer any confirmation or a way to fix it, I would be grateful.
On booting, it gives the following error:
Xmodem file system is available.
flashfs[0]: unable to allocate available block.
The system has been interrupted, or encountered an error
during initializion of the flash filesystem. The following
commands will initialize the flash filesystem, and finish
loading the operating system software:
flash_init
ether_init
tftp_init
boot
ap:
Trying to wake up the flash:
ap: flash_init
Initializing Flash...
flashfs[0]: unable to allocate available block.
...done Initializing Flash.
ap: dir flash
unable to stat flash/: permission denied
I have tried the standard recovery mode of uploading a new firmware via TFTP, but I can't even set variables:
ap: set IP_ADDR 10.0.0.1
flash:/env_vars.tmp: invalid argument
The filesystem containing the variables may not be initialized yet.Thanks for the tip, however I should probably have said the access points are autonomous, so the method you suggested will not work.
Yes it does.
You need a two-step method.
Your AP is booting up with either no IOS or a corrupt IOS.
1. In order to efficiently transfer the IOS to an AP that has no IOS you need to use the process I've posted earlier.
2. Once the AP boots up in autonomous mode, it's as easy as giving the BVI1 an IP address and use the command "copy tftp: flash:" to transfer the LWAP/CAPWAP IOS to the AP. -
Satellite P840 Win8 - touchpad intermittently stop responding
Hi, I've had my new laptop for 24 hours, and I've experienced twice a situation whereby the touchpad stops responding permanently, requiring the machine to be reboot (which "resolves" the problem). In addition to that, I've been experiencing intermittent freezes in response for about 3-4 seconds, then it starts responding again.
It's brand spanking new, so this is pretty disappointing. Has this happened to anyone else and if so, is there a fix that doesn't involve returning the unit?
Cheers,
PeteHi
Did you notice the same using a connected USB mouse?
Im asking this because from my point of view the touchpad or the system could freezes for some seconds because of stressed CPU.
In many cases the system doesnt response because some processes running in the background stresses the CPU and this leads to such system freezing.
I would not be worry about that check if the system is up to date and if all updates are installed.
In case this issue would not be related to the mentioned background process, try to update the touchpad driver.
Check the Toshiba EU driver page in order to get the latest touchpad driver or visit the Synaptics driver page in order to get the driver directly from touchpad manufacturer page. -
Cisco 1142 Wireless access point intermittently will not authenticate
Hi all,
We have a Cisco 1142 standalone access point, and from time to time I will come into the office and it will not authenticate any users to either our guest or corporate networks. I then have to go in and reboot the access point. After that, it begins to work. Any advice? Here's my configuration below:
Current configuration : 6450 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname cisco-chiap01
logging monitor errors
enable secret 5 $1$fsD8$CU42/3/Up5AAlL4hQWvvg0
aaa new-model
aaa group server radius rad_eap
server 172.17.16.12 auth-port 1645 acct-port 1646
server 172.17.21.10 auth-port 1812 acct-port 1813
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
server 172.17.21.10 auth-port 1812 acct-port 1813
aaa group server radius rad_eap2
server 172.17.16.12 auth-port 1645 acct-port 1646
server 172.17.21.10 auth-port 1812 acct-port 1813
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authentication login eap_methods2 group rad_eap2
aaa authorization exec default local
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
login on-failure log
login on-success log
dot11 syslog
dot11 vlan-name Admin vlan 100
dot11 vlan-name DevNetwork vlan 20
dot11 vlan-name Guest vlan 150
dot11 vlan-name Network vlan 16
dot11 ssid DevNetwork
vlan 20
authentication open eap eap_methods2
authentication network-eap eap_methods2
authentication key-management wpa version 2
dot11 ssid Guest
vlan 150
authentication open
authentication key-management wpa version 2
guest-mode
mbssid guest-mode
wpa-psk ascii 7 142407060101380B013A3A2670435642
information-element ssidl advertisement
dot11 ssid Network
vlan 16
authentication open eap eap_methods2
authentication network-eap eap_methods2
authentication key-management wpa version 2
username monkeyman privilege 15 secret 5 $1$ZZ7C$rqimu2FNONdfeacMNGAD/.
bridge irb
interface Dot11Radio0
no ip address
ip helper-address 172.17.19.10
no ip route-cache
encryption mode ciphers aes-ccm
encryption vlan 16 mode ciphers aes-ccm
encryption vlan 150 mode ciphers aes-ccm
encryption vlan 20 mode ciphers aes-ccm
ssid DevNetwork
ssid Guest
ssid Network
antenna gain 0
parent timeout 120
speed 5.5 11.0 basic-6.0 9.0 12.0 36.0 48.0 54.0
packet retries 128 drop-packet
channel 2462
station-role root
rts threshold 512
rts retries 128
interface Dot11Radio0.11
encapsulation dot1Q 11
no ip route-cache
interface Dot11Radio0.16
encapsulation dot1Q 16 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio0.20
encapsulation dot1Q 20
no ip route-cache
bridge-group 20
bridge-group 20 subscriber-loop-control
bridge-group 20 block-unknown-source
no bridge-group 20 source-learning
no bridge-group 20 unicast-flooding
bridge-group 20 spanning-disabled
interface Dot11Radio0.150
encapsulation dot1Q 150
no ip route-cache
bridge-group 150
bridge-group 150 subscriber-loop-control
bridge-group 150 block-unknown-source
no bridge-group 150 source-learning
no bridge-group 150 unicast-flooding
bridge-group 150 spanning-disabled
interface Dot11Radio1
no ip address
ip helper-address 172.17.19.10
no ip route-cache
encryption vlan 16 mode ciphers aes-ccm
encryption vlan 150 mode ciphers aes-ccm
encryption vlan 20 mode ciphers aes-ccm
ssid DevNetwork
ssid Guest
ssid Network
antenna gain 0
traffic-metrics aggregate-report
dfs band 3 block
mbssid
parent timeout 120
speed 6.0 12.0 basic-24.0 36.0 48.0 54.0
channel width 40-above
channel dfs
station-role root access-point
interface Dot11Radio1.11
encapsulation dot1Q 11
no ip route-cache
interface Dot11Radio1.16
encapsulation dot1Q 16 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1.20
encapsulation dot1Q 20
no ip route-cache
bridge-group 20
bridge-group 20 subscriber-loop-control
bridge-group 20 block-unknown-source
no bridge-group 20 source-learning
no bridge-group 20 unicast-flooding
bridge-group 20 spanning-disabled
interface Dot11Radio1.150
encapsulation dot1Q 150
no ip route-cache
bridge-group 150
bridge-group 150 subscriber-loop-control
bridge-group 150 block-unknown-source
no bridge-group 150 source-learning
no bridge-group 150 unicast-flooding
bridge-group 150 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
no keepalive
interface GigabitEthernet0.11
encapsulation dot1Q 11
no ip route-cache
interface GigabitEthernet0.16
encapsulation dot1Q 16 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface GigabitEthernet0.20
encapsulation dot1Q 20
no ip route-cache
bridge-group 20
no bridge-group 20 source-learning
bridge-group 20 spanning-disabled
interface GigabitEthernet0.100
encapsulation dot1Q 100
ip address 192.168.100.3 255.255.255.0
no ip route-cache
bridge-group 100
no bridge-group 100 source-learning
bridge-group 100 spanning-disabled
interface GigabitEthernet0.150
encapsulation dot1Q 150
no ip route-cache
bridge-group 150
no bridge-group 150 source-learning
bridge-group 150 spanning-disabled
interface BVI1
ip address 172.17.16.251 255.255.255.0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface GigabitEthernet0
access-list 1 permit 172.17.16.1
access-list 1 remark Admin network access
access-list 1 permit 192.168.100.0 0.0.0.255
radius-server attribute 32 include-in-access-req format %h
radius-server host 172.17.21.10 auth-port 1812 acct-port 1813 key 7 047958071C3561410D4A44
radius-server host 172.17.16.12 auth-port 1645 acct-port 1646 key 7 08045E471A48574446
radius-server host 172.17.21.10 auth-port 1645 acct-port 1646 key 7 1320051B185D56797F
radius-server timeout 15
radius-server vsa send accounting
bridge 1 route ip
line con 0
line vty 0 4
access-class 1 in
endWhen the issue occurs does that affect both 2.4GHz & 5GHz devices ? I would see which band operating devices affected.
I noticed you have set CH11 under Radio 0 statically. I would prefer to configure it as below so AP can change the channel depend on the environment.
int d0
channel least-congested
HTH
Rasika
**** Pls rate all useful responses **** -
WRT54G as Access Point & Intermittent Connectivity
So I followed the advice found here
http://forums.linksys.com/linksys/board/message?board.id=Wireless_Routers&message.id=26177
Hooking up a wired router to my WRT54G Router, which I am trying to use as an access point. I've set my LAN IP to 192.168.1.2, disabled DHCP, cables plugged into LAN ports, not the WAN port.I also changed it to Router Mode instead of gateway mode.
The problem is my wired router is my landlord's, and I don't have access to it. Anyway, I can usually connect, but sometimes it disconnects repeatedly, and it seems like i can't keep a connection for more than 5 minutes.
The problem doesn't seem to nearly as bad when I'm plugged directly into the wall (but there have been a couple times when I've gotten disconnected).
My theory is that I may be getting something mixed up with regards to my assigned IP address. When I'm plugged in i'm 192.168.1.108, but when I connect to the wireless, i'm almost always 192.168.1.100, even though there's only one DHCP server on the network. (this is just a guess, though)
Any advice you can give would be greatly appreciated. THANKS!I've updated the router's firmware I forgot to mention that in the original post. Are you sure regarding the "gateway mode", the little help blurb on the routers settings says that gateway should only be used when the router is the part of the network that deals directly with the wider internet. I am pretty sure I've tried it in both modes and was having this problem, because it was definately Gateway
-
WRT610N - Both laptops lose connection to access point intermittently
I've tried searching the forums a little but don't see my exact issue.
I have a WRT610N and two laptops (one Windows7 connected over N 5ghz and the other XP connecting over A 5ghz). From time to time, but at least twice a day, especially when doing a heavy download or streaming media, the laptop connection to the access point will be dropped. I have to disconnect from the wireless network and reconnect.
I verified that I was running the latest firmware. I never had to upgrade, was shipped with 2.00.00.05. THe 5ghz network uses WPA2 security and I tried switching from AES only to TKIP and AES. I also tried changing the key renewal interval. One laptop has a DHCP reservation and the other is allowed to get whatever IP. 20 or 40 Mhtz channel width is set to auto.
If anyone has any ideas of things to try before I go return the thing I would appreciate it.
Message Edited by jonredraider on 12-03-2009 11:42 PMOpen the setup page and Under Wireless tab..Click on Advanced Wireless Settings...Change the Beacon Interval to 75,Change the Fragmentation Threshold to 2304,Change the RTS Threshold to 2307 >>Click on "Save Settings"...
-
Open Directory intermittently stops responding
I'm trying to figure out how to get OD working reliably.
I've had a mac mini running OD and file services as primary authentication adn user managemetn.
I'm now running AD for user auth, and a standalone OD mac mini (10.9.x) with no other purpose in life but to be the OD master, on a new - ish Mac mini that hasn't evinced drive errors.
Nevertheless, OD simply gives up on an intermittent basis. I usually figure this out when I load system preferences and I cant get a list of replicas. Or when binding a new computer and it throws an error.
Rebooting clears the problem - for a little while. I can bind, the Server.app behaves properly, etc.
I also make sure to not leave a user session or server.app running, but log all the way back out.
Now - is there any way to verify the integrity of the db (and fix it)? Or to export/reimport the db without losing all my bindings and management settings in workgroup manager, but get a cleaner running copy?1. The OD master must have a static IP address on the local network, not a dynamic address.
Check
2. You must have a working DNS service, and the server's hostname must match its fully-qualified domain name. To confirm, select the server by name in the sidebar of the Server application window, then select the Overview tab. Click the Edit button on the Host Name line. On the Accessing your Server sheet, Domain Name should be selected. Change the Host Name, if necessary. The server must have at least a three-level name (e.g. "server.yourdomain.com"), and the name must not be in the ".local" top-level domain, which is reserved for Bonjour.
Check
3. The primary DNS server used by the server must be 127.0.0.1 (that is, itself) unless you're using another server for internal DNS. The only DNS server set on the clients should be the internal one, which they should get from DHCP if applicable.
Using active directory, but valid DNS all the way around
4. Follow these instructions to rebuild the Kerberos configuration on the master.
5. If you use authenticated binding, check the validity of the master's certificate. The common name must match the hostname and domain name. Deselecting and then reselecting the certificate in Server.app has been reported to have an effect in some cases. Otherwise delete all certificates and create new ones.
6. Unbind and then rebind the clients in the Users & Groups preference pane. Use the fully-qualified domain name of the master.
I'll look into the above, but I'm really trying to avoid rebinding 60+ machines yet again.
7. Reboot the master and the clients.
It works for a while and then just gives up. As stated - rebooting clears it - for a while.
Is there a way - I have not yet looked at the kerberos instructions - to validate the validity of the database and repair it without rebinding/losing everything?
8. Don't log in to the server with a network user's account.
Local admin all the way....
9. Disable any internal firewalls in use, including third-party "security" software.
none in effect or on.
10. If you've created any replica servers, delete them.
Done this, and back. Can try it again....
11. As a last resort, export all OD users. In the Open Directory pane of Server, delete the OD server. Then recreate it and import the users. Ensure that the UID's are in the 1001+ range. -
Cisco 1131 access point status led
Hi
Any one experienced a white light on the status led, its the "ring light" infront of the AP. ive checked on http://www.cisco.com/en/US/docs/wireless/access_point/1130/installation/guide/113h_c4.html where all colours are listed and none point done to white.
ANy ideas?
ThanksHere's an update on this issue. I have had about a 2% failure rate on my 3502i's due to blue, green, and white light freezing. We sent several unit to Cisco's wireless engineer team in Richfield. They have found the issue and have written a fix and are currently doing testing this weekend. They are sending a senior wireless engineer to my office on Monday morning to apply the fix on the 200 units that we have yet to deploy. This is the bad part: the fix can only be applied through the console port and they won't have this integrated into a controller code until May/June. The good news is they have a fix or will just RMA with no questions. I have a webex with their wireless team to explain exactly what the issue is, but from what I gathered is something to do with the boot loader image and the IBM chip in the unit. I will follow up with you guys on Mon/Tues.
Sent from Cisco Technical Support iPhone App -
WLC 5508 and remote site (DMVPN) Access Points
Hi All,
We just purchased a WLC 5508 and would like to know if it will control remote VPN site Access Points. Here are the details:
The 5508 will live at our home office. We have multiple remote sites that are connected via Cisco's DMVPN. Each site has one Cisco 1131 Access Point hanging off of either a Cisco 1841 or a 2811 that is using DMVPN back to the home office 2811. Can the 5508 manage the remote Access Points?
Thanks for your help guys!Are you are talking about OfficeExtend?
Cisco OfficeExtend
https://www.cisco.com/en/US/solutions/collateral/ns340/ns517/ns430/solution_overview_c22-523307_ns348_Networking_Solution_Solution_Overview.html
OfficeExtend supports 1130 & 1140 as long as you have the Wireless PLUS (WPLUS) Software.
OfficeExtend Access Point
http://www.cisco.com/en/US/docs/wireless/wcs/6.0/configuration/guide/6_0apcfg.html#wp1069890 -
Unable to stop the event logs on access point console
Hi team,
I have an AIR-LAP1131AG-E-K9 access point having ios c1130-k9w8-mx.124-21a.JHB1.
When I am trying to take the console of it there are many logs generated like LWAPP ...Go join the controller, Discover controller etc. and the ap is unable to register to the controller(2112 with ios version 6.0.199.4). I'm trying to enter the command but there are many event msg generated....How do i stop this event log. I tried entering the command no debug all. but still there are many logs...
I want to enter the the following commands
#lwapp ap ip address <ip addr>.
#lwapp a pip default-gateway <gateway ip addr>
#lwapp ap controller ip addr <controller ip>
#wr me
Revert me back on urgent basis
Thanks in advance..Thanks Rashika,
Now the access point got registered to the controller..This happened becuse of country Code..
I have changed the country code to UK, Belgium it started working fine.
Initially when it was IN the access point was not getting register..
But now the problem which arised is that the user is unable to get authenticated to the radius server.
Radius server is reachable and we have done every changes required for radius server authentication.
Users are getting rejected.
Customer is saying that the radius server is in IN domain and the WLC/access point is in UK,BE and hence the users are unable to connect..
Is it so??
Rply
Thanks in advance... -
Am not able to use facebook on my Iphone 4, softwareversion:iOS7.1, also tried to access through safari and chrome that i have installed it gives an error message saying: "safari could not open the page because server stopped responding", i tried network reset, reset the whole device, rebooting , changing airplane mode rebooting nothing fix the issue, but i can access other sites and google , am using Vodafone as my carrier with 2g network, when at home able to access facebook.com through wifi in safari requesting assistance thank you
If you can access Facebook while on Wifi at home, but you are unable to access it while away running on your carrier's 2G network, I could phone your carrier. You have already completed the Cellular Data troubleshooting for the iPhone, so any limitations keeping your from connecting to Facebook over cellular will have to be answered by your carrier.
-
I cannot acces Safari (for the past three days) A message shows 'Safari could not open the page because the server stopped responding. How can I rectify this?
Well, you are accessing Safari. It's just that there's a page it's trying to access on the web, one that you last used, and that website is not available. When looking at the dead page in Safari, tap the lower right icon to shrink down the page and then tap the "x" to get rid of it. You can then try going to another site.
Maybe you are looking for
-
How do I sync my email so that what is on my PC reflects on my iphone
How do I sync my email so that what is on mu PC reflects on my phone. Currently if I delete an email it remains on my phone. Is there a way to fix this?
-
Out of memory errors shortly after saving Adobe LiveCycle Designer
Stuck in a loop. I am being forced to give up on a pdf that I put hours of work in. I can open the document and work in it for a while, but one large text box will instantly crash the program if I select it. The name of the text box is very long. T
-
In BizTalk Send port, we have an option to enable service window but it works if we need to make a call with in a specific period. My requirement is, For instance to make a call at 9:00 AM, 11:00 AM, 02:00 PM, 04:00 PM like that. Is there a way to im
-
Policy Agent 2.2 /SJSAS 9.1 EE: security works sporadically
Hi, Ive been having some trouble getting SSO working between my Sun Portal Server 7.1/Access Manager 7.1 running on my Solaris x86 machine and the Sun Application Server 9.1 EE with a Sun AM Policy Agent 2.2 on it. I'm deploying an Java EE app that u
-
Custom Authority Check across system
Hi all I have got an authority check requirement I need help with. I have to restrict certain users --which have a specified role- to not be able to access certain profit/cost centers in any reporting activity. When these users run any report transac