Document on 1131 Access point

Please provide the documentation to configure 1131 Access Point.
We are getting documentation for 1130 and not for 1131.
Help wouldl be highly apprecited.

Hi Navinder,
It's the same. 1130 is the generic model number while 1131/1132 is a specific model number.

Similar Messages

1131 ACCESS POINTS BOUNCING

I have a site with Lightweight 1131 access points, with 5508 WLC's in HA running Code 7.4.110. In 2 areas of one site the access points are bouncing, I have attached the logs from one of the AP's at the site. The switch that the AP's are connected to is a WS-C3750-24P SW VERSION: 12.2(55)SE1. This has only happened in 2 areas on the site, and only 24 Access Points out of 335. HELP!!!!!!

Hi Scott
I have 184.2 Watts remaining on the switch. I have just come back from site having tried the following:
1. Took and AP from another site, this worked.
2. Bounced the Access Points to a controller still running 7.3.101.0 this also worked.
3. Bounced the Ap's back to their local controller, they went back to not functioning correctly.
We upgraded to Code 7.4.110 it was an,assured, tested version from Cisco, to fix other issues we had. Any help would be welcome.

Cisco module controller & 1131 access-point

I'm using a blade as a controller in a cisco router. trouble is it does not see
the 1131 access-points. does see 1020 access points. Any thoughts

If you are using OP 43 to tell the access points where to find the controllers you will need a new entry for the 1130 series of access points.

1131 access point, broken flash?

I have had two 1131 access points die in the last few weeks, both with the same symptoms. I suspect both have broken flash systems and are due for the bin. If anyone can offer any confirmation or a way to fix it, I would be grateful.
On booting, it gives the following error:
Xmodem file system is available.
flashfs[0]: unable to allocate available block.
The system has been interrupted, or encountered an error
during initializion of the flash filesystem. The following
commands will initialize the flash filesystem, and finish
loading the operating system software:
    flash_init
    ether_init
    tftp_init
    boot
ap:
Trying to wake up the flash:
ap: flash_init
Initializing Flash...
flashfs[0]: unable to allocate available block.
...done Initializing Flash.
ap: dir flash
unable to stat flash/: permission denied
I have tried the standard recovery mode of uploading a new firmware via TFTP, but I can't even set variables:
ap: set IP_ADDR 10.0.0.1
flash:/env_vars.tmp: invalid argument
The filesystem containing the variables may not be initialized yet.

Thanks for the tip, however I should probably have said the access points are autonomous, so the method you suggested will not work.
Yes it does.
You need a two-step method.
Your AP is booting up with either no IOS or a corrupt IOS.
1. In order to efficiently transfer the IOS to an AP that has no IOS you need to use the process I've posted earlier.
2. Once the AP boots up in autonomous mode, it's as easy as giving the BVI1 an IP address and use the command "copy tftp: flash:" to transfer the LWAP/CAPWAP IOS to the AP.

Cisco 1131 access point status led

Hi
Any one experienced a white light on the status led, its the "ring light" infront of the AP. ive checked on http://www.cisco.com/en/US/docs/wireless/access_point/1130/installation/guide/113h_c4.html where all colours are listed and none point done to white.
ANy ideas?
Thanks

Here's an update on this issue. I have had about a 2% failure rate on my 3502i's due to blue, green, and white light freezing. We sent several unit to Cisco's wireless engineer team in Richfield. They have found the issue and have written a fix and are currently doing testing this weekend. They are sending a senior wireless engineer to my office on Monday morning to apply the fix on the 200 units that we have yet to deploy. This is the bad part: the fix can only be applied through the console port and they won't have this integrated into a controller code until May/June. The good news is they have a fix or will just RMA with no questions. I have a webex with their wireless team to explain exactly what the issue is, but from what I gathered is something to do with the boot loader image and the IBM chip in the unit. I will follow up with you guys on Mon/Tues.
Sent from Cisco Technical Support iPhone App

1131 access point intermittently stops responding

We have an 17 offices with the same basic wireless config. 2 or 3 ap's with the same configuration on them. This one particular office has 2 ap's that intermittently will stop responding to pings and are no longer reachable via telnet or http and users cannot connect through the ap. We are running c1130-k9w7-mx.124-3g.JA1/c1130-k9w7-mx.124-3g.JA1.
I had the site (located in Spain) send me pics of the ap's and noticed that they are not mounted, just laying on ceiling tiles in a plenum ceiling.
Once the ap's are again reachable there is nothing in the log that would suggest there was a problem and the ap does not reboot.
Any ideas?
here is the config...
ap1_spain#sh run
Building configuration...
Current configuration : 6901 bytes
! Last configuration change at 17:23:30 +0200 Tue Sep 14 2010 by dguse
! NVRAM config last updated at 17:23:30 +0200 Tue Sep 14 2010 by dguse
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec localtime show-timezone
service password-encryption
hostname ap1_spain
aaa new-model
aaa authentication login default group tacacs+ none
aaa authentication login no_aaa none
aaa authorization console
aaa authorization exec default group tacacs+ none
aaa authorization exec no_aaa none
aaa authorization commands 15 default group tacacs+ none
aaa authorization commands 15 no_aaa none
aaa accounting exec default start-stop group tacacs+
aaa accounting commands 15 default start-stop group tacacs+
aaa session-id common
resource policy
clock timezone +0200 2
ip subnet-zero
dot11 ssid xxxxxxxxx
   authentication open
   authentication key-management wpa
   wpa-psk ascii 7 03055908555ABA1A1A5F4D071616
dot11 network-map
power inline negotiation injector 0017.0ed7.442f
crypto pki trustpoint TP-self-signed-1171819700
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1171819700
revocation-check none
rsakeypair TP-self-signed-1171819700
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers tkip
ssid linvatec
power local 14
power client 14
station-role root
world-mode dot11d country ES both
no cdp enable
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
encryption mode ciphers tkip
dfs band 3 block
channel dfs
station-role root
no cdp enable
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
speed 100
full-duplex
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 10.x.x.x 255.255.255.0
no ip route-cache
ip default-gateway 10.x.x.x
no ip http server
ip http authentication aaa login-authentication default
ip http authentication aaa exec-authorization default
ip http authentication aaa command-authorization 15 default
ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
snmp-server view dot11view ieee802dot11 included
snmp-server community xxxxxxxxxxxxxx RO
snmp-server location Barcelona
snmp-server chassis-id ap1_spain
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps tty
snmp-server enable traps entity
snmp-server enable traps disassociate
snmp-server enable traps deauthenticate
snmp-server enable traps authenticate-fail
snmp-server enable traps dot11-qos
snmp-server enable traps switch-over
snmp-server enable traps rogue-ap
snmp-server enable traps wlan-wep
snmp-server enable traps config-copy
snmp-server enable traps config
snmp-server enable traps syslog
snmp-server enable traps cpu threshold
snmp-server enable traps aaa_server
tacacs-server host 10.x.x.x
tacacs-server directed-request
tacacs-server key 7 071C244F5B461C1D0D1079282A2D27222D010C
bridge 1 route ip
line con 0
authorization commands 15 no_aaa
authorization exec no_aaa
login authentication no_aaa
line vty 0 4
sntp server 10.x.x.x
sntp broadcast client
end

Hi,
     What is the switchport config of the port connected to the AP? The AP is set to be 100/Full, if the switch isn't set as well, you could be going half-duplex and losing connecitvity due to that.

WLC 5508 and remote site (DMVPN) Access Points

Hi All,
We just purchased a WLC 5508 and would like to know if it will control remote VPN site Access Points. Here are the details:
The 5508 will live at our home office. We have multiple remote sites that are connected via Cisco's DMVPN. Each site has one Cisco 1131 Access Point hanging off of either a Cisco 1841 or a 2811 that is using DMVPN back to the home office 2811. Can the 5508 manage the remote Access Points?
Thanks for your help guys!

Are you are talking about OfficeExtend?
Cisco OfficeExtend
https://www.cisco.com/en/US/solutions/collateral/ns340/ns517/ns430/solution_overview_c22-523307_ns348_Networking_Solution_Solution_Overview.html
OfficeExtend supports 1130 & 1140 as long as you have the Wireless PLUS (WPLUS) Software.
OfficeExtend Access Point
http://www.cisco.com/en/US/docs/wireless/wcs/6.0/configuration/guide/6_0apcfg.html#wp1069890

Access point document

we need to place a access point on floor. For 1 Mbps it works for 450 feet. Now walls are constructed with Mi-one tech.
I need a document from which i can get information about strength of signal or obstacals that might degrade signals
please guide us
pushpak

Hi Pushpak,
Signal attenuation or signal loss occurs even as the signal passes through air. The loss of signal strength is more pronounced as the signal passes through different objects. A transmit power of 20 mW is equivalent to 13 dBm. Therefore, if the transmitted power at the entry point of a plasterboard wall is at 13 dBm, the signal strength will be reduced to 10 dBm when exiting that wall.Here some examples;
Plasterboard wall Signal Attenuation 3 dB
Glass wall with metal frame Signal Attenuation 6 dB
Cinder block wall Signal Attenuation 4 dB
Office window Signal Attenuation 3 dB
Metal door Signal Attenuation 6 dB
Metal door in brick wall Signal Attenuation 12 dB
Human body Signal Attenuation 3 dB
From this good site survey doc;
http://www.cisco.com/en/US/products/hw/phones/ps379/products_implementation_design_guide_chapter09186a00802a09e0.html
Hope this helps!
Rob

Bridging with 1131 Ag series access point.

Hi,
I want to use 1131 AG series access point for bridging between two buildings which are 20 metres apart from each other.
Is it possible and what are the limitation for this design?
Please help.
thanks in advance.
Pulkit Sharma

Hi Pulkit,
The autonomous 1130AG series access point supports these operating wireless modes:
? Root access point?Connected to a wired LAN and supports wireless clients.
? Repeater access point?Not connected to a wired LAN, associates to a root access point, and supports wireless clients
? Workgroup bridge?Not connected to a wired LAN, associates to a root access point or bridge, and supports wired network devices.
As this unit was not designed to be use outdoors, having a clean RF line of sight is really difficult. To be honest I do not think this unit was designed to connect two remote buildings even if the units are indoors. I would look for APs with detachable antennas like the 1242AG or the 1200 modular series so you can use external antennas and bridging roles.
Hope it helps,
Roger Carpio.

Guest use of a Aironet 1131AG Access Point

I have 2 WLAN's using (mostly) D-Link products - one is for staff only and the other is for guests, and is totally separate from our LAN.
I'm disappointed with D-Link and want to change-over to all-Cisco AP's. I'm fairly satisfied with the 1131 and wish to build on it.
The manual mentions a guest SSID, but I have reservations about network security. (I am thinking of using a single WLAN with multiple SSID's to handle the staff and guests.) What is the opinion on this forum on this issue? (I'm very new to Cisco and classify myself as little more than a beginner with wireless in general.)
Mike Webb
1-man IT shop for a conservation non-profit in central Nebraska

Here's an overview of Cisco's "Granular Guest Access Management and Provisioning" (http://www.cisco.com/en/US/prod/collateral/wireless/ps5678/ps6973/ps8382/prod_brochure0900aecd806b8a72_ps6087_Product_Solution_Overview.html).
Here's is a document on how to configure Guest Access on an Autonomous AP:
VLANs on Aironet Access Points Configuration Example
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a0080665ceb.shtml

Can't HP Officejet pro 8100 do wifi access point?

Yesterday my HP Officejet pro 8100 arrived and I try to connect via wifi. I thinked that It need a infrastructure access point to print via wifi.
When I powered on the printer I osserved that It create an access point autonomously with SSID: HP-Setup-7A-Officejet Pro, with IPv4 address server, etc...
I was very happy and I printed a page with my smartphone samsung s4 connected directly with printer access point (not wifi direct but standard wifi).
Today no changed occurred but I can't use printer with its own access point, but only with an external wifi access point.
Someone can help me, please? It could be an hardware problem?
Thanks,
Luca
P.S. in web server I checked that "access point connectivity" (Punto di accesso wireless connettività in Italian) is checked.
This question was solved.
View Solution.

Hello lucait
To print via WiFi you need to have a wireless router setup. Once you have the wireless router setup correctly you will have a SSID and Wepkey that will enable you to add devices to your network. The network will allow all your devices to communicate not just with each other but with the internet. At the moment your printer was not put in a network so instead of broadcasting on a network it is broadcasting on it's own network called HP-Setup-7A-Officejet Pro which is only good for a short period of time to allow you to setup your wireless. I am going to assume you have a wireless network and you are just needing assistance getting the printer setup on that network.
To set your printer up on a network you will need to reset your network defaults so your printer begins to broadcast that HP-Setup-7A-Officejet Pro network again. You can do this buy following the steps on the HP Support document Resetting the Network Settings. Once you have done this you can begin to install the software that came with your printer on your computer. You want to set the printer up wirelessly when the option arrives. The software should configure your printers wireless for you and put it on the network. Once completed you should be able to access your printer from all your devices as long as they are on the network.
I hope this helps resolve your wireless issue. Thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

Access points

Hello
At my workplace we have this printer, HP LaserJet Pro 200 color MFP M276n. And it has been connected to the wireless network since we bought it, until today.
The direct feedback from the printer is that the "WEP password was not recogniced". The network has a wpa2 encryption, and if that is a problem I don't know how it worked in the first place.
While trying to lookup what up (yea....), I print out the wireless report. It says that the network it's trying to connect to has multiple access points.
The network has a wpa2 encryption, and if that is a problem I don't know how it worked in the first place. We do have two different networks, but while looking for it from the printer I't cant find it.
All other devices workes, but alas not this printer.

Hi @SpikeSent , and welcome to the HP Forums.
I see you're having access issues. I would love to try and help you, but I do need a little information first. I am linking a few HP Support documents below that will show you how to find your product number. Also, please include which operating system you are using. Also, if you're using Windows, please include whether your operating system is 32-bit or 64-bit. With this information and the product number we can provide you with accurate information.
How Do I Find My Model Number or Product Number?
Mac OS X: How Do I Find Which Mac OS X Version Is on My Computer?
Which Windows operating system am I running?
Is the Windows Version on My Computer 32-bit or 64-bit?
Please let em know what you find. Thanks for posting on the HP Forums.
Please click “Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks" for helping!
Jamieson
I work on behalf of HP
"Remember, I'm pulling for you, we're all in this together!" - Red Green.

Access points wont accept clients on 2.4 GhZ

Hi
We are having some Issue with some Access Points are dropping clients on 2.4 GhZ radio, the radio is if you SSH to the Access Point "Dot11Radio0 is up, line protocol is up".
Our setup is 2 x Wism2 controller (7.5), a CPI (1.4), and around 750 Access points of various types (1121, 1131, 1142, 2602).
If we reset the Access Point from CPI it comes up and it will again accept clients on 2.4 GhZ for a random time period, sometimes it works for some hours, sometimes for a couple of days, total random.
The once we have seen the problem on is as I know 1142:
Software Version
7.5.102.0
Boot Version
12.4.23.0
AP Model
AIR-LAP1142N-E-K9
IOS Version
15.2(4)JA1$
Hope to get help finding a solution.
Best regards
Jørgen

If you have a high density deployment, you might want to look at your RRM. What is the power set to on the AP's. If the power is set too low, that can cause clients not to see or be able to join an access point. If this is the case, you need to set the min tx power level for the 2.4ghz radio which is under the wireless tab in the 802.11bgn TPC.
If you have an issue with a certain AP model, it might be a bug, but you didn't mention what model AP is was happening to.
Sent from Cisco Technical Support iPhone App

Wireless bridging is not working in 1552 outdoor access point and 2602e indoor access point.

Hi,
I am have been tested wireless bridging with 2 indoor Cisco 2602 access point by following the attached document and its working fine without any issue.
After then I made one Cisco 1552 EU-M-K9 outdoor access point as RAP, then connect to this RAP with one 2602 mesh access point. But its not working, mesh access point is just start scan the signal to get associate with RAP, but not getting established. Is there any specific configuration required to connect between outdoor and indoor access point. Kindly find the attachment and advise.
regards,
Jubair.S

Hi Team,
Any suggestion??
Regards,
Jubair.S

Capturing MAC Addresses from an Access Point AP1131 with SNMP

Hi!
I'm trying to use SNMP to track information as to whats connected to
our access points. The purpose is basic security and auditing in case
of a problem ( virus, technical problem, etc ). We're already able to
capture what wired devices are connected, but not the MAC addresses of
the wireless clients.
We're employing Cisco Aironet APs 1131, and looking around the MIBs, I found
one object that has what I want, but it's not accessible.
cDot11ClientAddress OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The MAC address of the client."
::= { cDot11ClientConfigInfoEntry 1 }
Does any one know another way to get this information via SNMP?
Thanks U by advance!
Khay

Up...anybody?... :(

Document on 1131 Access point

Similar Messages

Maybe you are looking for