1532E MAP disassociating - Cause=Radio reset due to configuration change.
Hello,
have a1532E MAP with WLC 2504 and 7.6.100.0 that shows oddly enough "Cause=Radio reset due to configuration change" and the interface resets.
Any idea how this comes about without any changes made.
Relevant log attached.
After updating to 7.6.120 we've noticed that some of our AP's wouldn't come up. After looking in the switch's logs I found this
chassis: Ports PoE usage has exceeded threshold of 80%.
The power drawn is 117w (show power-over-ethernet).
When I use the following command: show power-over-ethernet brief I get this:
PoE | Power Power Alloc Alloc Actual Configured Detection Power Pre-std
Port | Enable Priority By Power Power Type Status Class Detect
----- + ------ -------- ----- ----- ------ ----------- ----------- ----- ------
1 | Yes low lldp 17 W 7.0 W Delivering 3 off
2 | Yes low lldp 17 W 7.0 W Delivering 3 off
3 | Yes low lldp 17 W 6.8 W Delivering 3 off
4 | Yes low lldp 17 W 7.1 W Delivering 3 off
5 | Yes low lldp 17 W 7.0 W Delivering 3 off
6 | Yes low lldp 17 W 6.9 W Delivering 3 off
7 | Yes low lldp 17 W 6.8 W Delivering 3 off
8 | Yes low lldp 17 W 6.7 W Delivering 3 off
9 | Yes low lldp 17 W 6.9 W Delivering 3 off
10 | Yes low usage 17 W 0.0 W Disabled 3 off
Port 10 is where the missing AP is on.
How is it possible that after the update to 7.6.120 the AP won't work anymore?
Similar Messages
-
Collection Segment closed due to configuration change
Hi
Our collection supervisor had created new collection groups and assigned them to the colleciton segment. But when she goes into the UDM_BP_GRP transaction to change the collection group assignment to the BP, she is getting this error message:
UDM_BUPA_MSG002 - Collection Segment closed due to configuration change
But the collection segments are still released, assigned to the collection profile. Nothing has changed except that new collection groups have been added.
Has anyone seen this issue before?
Thanks,
ChaitMark,
Thanks for your reply. The new groups are assigned to the collection segments in the same profile. I tried to change the profile manually in BP thinking that would refresh the segments. But it did not make any difference. Note that it is UDM_BP_GRP that is not working, we can still change the group in the BP directly (UDM_BP).
I never had this issue before and I couldn't find anything on OSS. -
WLC 4400 and LAP 1131 radio reset daily at 2 P.M.
192 Tue Mar 25 14:35:46 2014 AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:00:24:c4:1d:11:10 Cause=Radio interface reset. Status:NA
193 Tue Mar 25 14:35:46 2014 AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:00:24:c4:8f:79:b0 Cause=Radio reset due to Init. Status:NA
194 Tue Mar 25 14:35:46 2014 AP's Interface:1(802.11a) Operation State Up: Base Radio MAC:00:24:c4:8f:82:e0 Cause=Radio reset due to Init. Status:NA
195 Tue Mar 25 14:35:46 2014 AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:00:24:c4:8f:82:e0 Cause=Radio reset due to Init. Status:NA
196 Tue Mar 25 14:35:46 2014 AP 'LAP-2F-2_54f8', MAC: 00:24:c4:8f:7f:40 disassociated previously due to AP Reset. Uptime: 15 days, 12 h 03 m 31 s . Last reset reason: operator changed 11g
==================================================================================================================
*apfReceiveTask: Mar 25 14:35:46.949: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:290 RRM LOG: Airewave Director: Could not find valid channel lists for 802.11bg
*spamReceiveTask: Mar 25 14:35:46.628: %LOG-3-Q_IND: rrmChanUtils.c:290 RRM LOG: Airewave Director: Could not find valid channel lists for 802.11bg
*apfReceiveTask: Mar 25 14:35:46.554: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:290 RRM LOG: Airewave Director: Could not find valid channel lists for 802.11bg
*spamReceiveTask: Mar 25 14:35:46.042: %LOG-3-Q_IND: rrmChanUtils.c:290 RRM LOG: Airewave Director: Could not find valid channel lists for 802.11bg
*apfReceiveTask: Mar 25 14:35:45.971: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:290 RRM LOG: Airewave Director: Could not find valid channel lists for 802.11bg
*apfReceiveTask: Mar 25 14:35:45.321: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:290 RRM LOG: Airewave Director: Could not find valid channel lists for 802.11bgSimilar issue resolved here
https://supportforums.cisco.com/discussion/11015036/ap1141-rebooting-constantly -
Missing AP Multicast Mode IP Causing 3502i AP Radio Resets?
Has anyone else experienced AP radio resets when the AP Multicast Mode IP is set 0.0.0.0 under the General Tab?
I rebuilt my lab controller and moved the management interface to a new subnet. Somehow, the AP Multicase Mode IP under the General Settings was removed. Afterwards, my AP's radios would reset every 2-3 minutes. After comparing my lab config to production, I noticed the IP was missing from that field. Setting the Multicast IP to 239.232.78.1 fixed the issue.
Can someone explain this to me?
WLC 2504
AP 3502i
Code Version: 7.3.101.0
Thanks for reading!Well was on a different code and changed the IP on my WLC and the multicast address didn't change. I did encounter it default to all zeros when I upgraded once but don't remember what code it was. The beta code I'm on doesn't allow me to change my multicast address to all zero's or else I would of tested it out.
On the code you are running, can you change it back to all zeros? If so, can you reproduce the issue?
Sent from Cisco Technical Support iPhone App -
LAP 1142N "Radio disabled due to PoE" after upgrade to 7.6.120
Recently, we upgraded our 5508 wireless controllers from 7.4.110.0 to 7.6.120.0.
One AP (AIR-LAP1142N-E-K9) doesn't work now.
Both radios are stuck in state 'reset':
AP#sh int dot11Radio 0 | inc Dot11Radio0
Dot11Radio0 is reset, line protocol is down
It seems to be a PoE issue:
AP#sh controllers dot11Radio 0
Radio disabled due to PoE
This 1142N is connected to a HP switch (model 3800 with 802.3af/802.3at support). It did work on this switch several months before this upgrade and it works if connected to Cisco switch (Cat 6513).
We didn't upgrade the switch firmware or change its configuration.
The PoE status from the switch CLI:
PoE | Power Power Alloc Alloc Actual Config Detection Power Pre-std
Port | Enable Priority By Power Power Type Status Class Detect
------ + ------ -------- ----- ----- ------ -------- ----------- ----- ------
21 | Yes low lldp 33 W 7.8 W Delivering 3 off
Other APs (80 3602 connected to HP8212zl switches) do work without any problem.
Any idea how to solve this?After updating to 7.6.120 we've noticed that some of our AP's wouldn't come up. After looking in the switch's logs I found this
chassis: Ports PoE usage has exceeded threshold of 80%.
The power drawn is 117w (show power-over-ethernet).
When I use the following command: show power-over-ethernet brief I get this:
PoE | Power Power Alloc Alloc Actual Configured Detection Power Pre-std
Port | Enable Priority By Power Power Type Status Class Detect
----- + ------ -------- ----- ----- ------ ----------- ----------- ----- ------
1 | Yes low lldp 17 W 7.0 W Delivering 3 off
2 | Yes low lldp 17 W 7.0 W Delivering 3 off
3 | Yes low lldp 17 W 6.8 W Delivering 3 off
4 | Yes low lldp 17 W 7.1 W Delivering 3 off
5 | Yes low lldp 17 W 7.0 W Delivering 3 off
6 | Yes low lldp 17 W 6.9 W Delivering 3 off
7 | Yes low lldp 17 W 6.8 W Delivering 3 off
8 | Yes low lldp 17 W 6.7 W Delivering 3 off
9 | Yes low lldp 17 W 6.9 W Delivering 3 off
10 | Yes low usage 17 W 0.0 W Disabled 3 off
Port 10 is where the missing AP is on.
How is it possible that after the update to 7.6.120 the AP won't work anymore? -
Getting error in mailing program :Cause: FDPSTP failed due to ORA-29277
in the following program i am submitting a request and sending concurrent program log file (.REQ file)as an attachment but getting
following error,plese tell me where i am wrong
ORACLE error 29277 in FDPSTP
Cause: FDPSTP failed due to ORA-29277: invalid SMTP operation
ORA-06512: at "SYS.UTL_SMTP", line 44
ORA-06512: at "SYS.UTL_SMTP", line 150
ORA-06512: at "SYS.UTL_SMTP", line 383
ORA-06512: at "SYS.UTL_SMTP", line 399
ORA-0651
code:
CREATE OR REPLACE PACKAGE BODY APPS.xx_create_acct
AS
PROCEDURE submit_request(
errbuf OUT VARCHAR2,
retcode OUT VARCHAR2,
Source_Application varchar2,
Application number,
Dummy_Parameter_0 varchar2,
Ledger number,
Process_Category varchar2,
End_Date varchar2,
Create_Accounting_Flag varchar2,
Dummy_Parameter_1 varchar2,
Accounting_Mode varchar2,
Dummy_Parameter_2 varchar2,
Errors_Only_Flag varchar2,
Report varchar2,
Transfer_to_GL_Flag varchar2,
Dummy_Parameter_3 varchar2,
Post_to_GL_Flag varchar2,
GL_Batch_Name varchar2,
Mixed_Currency_Precision Number,
Include_Zero_Amt_Lines_Flag varchar2,
Request_ID varchar2,
Entity_ID Number,
Source_Application_Name varchar2,
Application_Name varchar2,
Ledger_Name varchar2,
Process_Category_Name varchar2,
Create_Accounting varchar2,
Accounting_Mode_Name varchar2,
Errors_Only varchar2,
Report_Level varchar2,
Transfer_to_GL varchar2,
Post_in_GL varchar2,
Include_Zero_Amount_Lines varchar2,
Valuation_Method varchar2,
Security_ID_Integer_1 varchar2,
Security_ID_Integer_2 varchar2,
Security_ID_Integer_3 varchar2,
Security_ID_Char_1 varchar2,
Security_ID_Char_2 varchar2,
Security_ID_Char_3 varchar2,
Concurrent_Request_ID number,
P_INCLUDE_USER_TRX_ID_FLAG varchar2,
P_INCLUDE_USER_TRX_IDENTIFIERS varchar2,
P_DEBUG_FLAG varchar2
IS
l_senderemail VARCHAR2 (2000) := '[email protected]';
l_request_id NUMBER;
errmsg VARCHAR2 (1000);
req_id NUMBER;
phase VARCHAR2 (200);
status VARCHAR2 (200);
dphase VARCHAR2 (200);
dstatus VARCHAR2 (200);
MESSAGE VARCHAR2 (200);
wait_stat BOOLEAN;
l_file_name VARCHAR2 (200);
l_file_path VARCHAR2 (2000);
crlf VARCHAR2 (4) := CHR (13) || CHR (10);
v_set_layout_option BOOLEAN;
dir_name varchar2(100);
/* CURSOR req_status
IS
SELECT SUBSTR (outfile_name, 55, 23) filename,
SUBSTR (outfile_name, 1, 64) outfilepath
FROM applsys.fnd_concurrent_requests
WHERE request_id = l_request_id
AND phase_code = 'C'
AND status_code = 'C';*/
directory_path VARCHAR2 (2000);
lv_subject VARCHAR2 (100);
lv_msg VARCHAR2 (700);
lv_msghdr VARCHAR2 (100);
lv_pdf_filename VARCHAR2 (200);
BEGIN
apps.fnd_global.apps_initialize
(user_id => apps.fnd_global.user_id,
resp_id =>apps.fnd_global.resp_id,
resp_appl_id => apps.fnd_global.resp_appl_id
l_request_id :=
apps.fnd_request.submit_request
( 'BOM',
'CSTCRACCRCV',
NULL,
NULL,
FALSE,
Source_Application,
Application ,
Dummy_Parameter_0,
Ledger ,
Process_Category,
End_Date ,
Create_Accounting_Flag,
Dummy_Parameter_1 ,
Accounting_Mode ,
Dummy_Parameter_2,
Errors_Only_Flag,
Report ,
Transfer_to_GL_Flag,
Dummy_Parameter_3,
Post_to_GL_Flag ,
GL_Batch_Name ,
Mixed_Currency_Precision,
Include_Zero_Amt_Lines_Flag,
Request_ID ,
Entity_ID,
Source_Application_Name,
Application_Name,
Ledger_Name ,
Process_Category_Name,
Create_Accounting ,
Accounting_Mode_Name,
Errors_Only ,
Report_Level,
Transfer_to_GL,
Post_in_GL ,
Include_Zero_Amount_Lines,
Valuation_Method ,
Security_ID_Integer_1,
Security_ID_Integer_2,
Security_ID_Integer_3,
Security_ID_Char_1 ,
Security_ID_Char_2 ,
Security_ID_Char_3 ,
Concurrent_Request_ID,
P_INCLUDE_USER_TRX_ID_FLAG,
P_INCLUDE_USER_TRX_IDENTIFIERS,
P_DEBUG_FLAG
COMMIT;
IF (l_request_id <= 0)
THEN
errmsg := apps.fnd_message.get ();
ELSE
wait_stat :=
apps.fnd_concurrent.wait_for_request (l_request_id,
10,
360,
phase,
status,
dphase,
dstatus,
MESSAGE
IF dphase = 'COMPLETE'
THEN
dir_name :='XX_CREATE_ACCT_LOG';
l_file_name := 'l' || l_request_id || '.REQ';
lv_subject := NULL;
lv_msg := NULL;
lv_msghdr := NULL;
lv_pdf_filename := NULL;
lv_subject := 'testing mail :Request for Create Accounting not completed';
lv_msg :=
'Please find attachement here with the Status Of Create Accounting Reciving from cost management'
|| crlf;
lv_msghdr := 'Dear Sir' ;
lv_pdf_filename := l_file_name;
send_mail (l_senderemail,
'[email protected]',
lv_subject,
lv_msghdr,
lv_msg,
lv_pdf_filename,
'text/application',
dir_name
END IF;
END IF;
END submit_request;
PROCEDURE send_mail (
p_sender IN VARCHAR2,
p_recipient IN VARCHAR2,
p_subject IN VARCHAR2,
p_mailbodyhdr IN VARCHAR2,
p_mailbody IN VARCHAR2,
p_filename IN VARCHAR2,
p_filetype IN VARCHAR2,
dir_name in VARCHAR2
AS
v_msg VARCHAR2 (32000);
src_file BFILE;
i INTEGER := 1;
v_raw RAW (500);
v_length INTEGER := 0;
v_buffer_size INTEGER := 57;
v_mailconn UTL_SMTP.connection;
gc_crlf VARCHAR2 (4) := CHR (13)
|| CHR (10);
gc_lf VARCHAR2 (4) := CHR (10);
crlf VARCHAR2 (2) := CHR (13)
|| CHR (10);
gc_mailhost VARCHAR2 (255) := '172.16.11.2';
-- gc_maildomain VARCHAR2 (255) := 'pune.com';
msg VARCHAR2 (32767);
boundary CONSTANT VARCHAR2 (256)
:= '-----7D81B75CCC90D2974F7A1CBD';
first_boundary CONSTANT VARCHAR2 (256)
:= '--' || boundary || UTL_TCP.crlf;
last_boundary CONSTANT VARCHAR2 (256)
:= '--' || boundary || '--' || UTL_TCP.crlf;
-- A MIME type that denotes multi-part email (MIME) messages.
multipart_mime_type CONSTANT VARCHAR2 (256)
:= 'multipart/mixed; boundary="' || boundary || '"';
BEGIN
DBMS_OUTPUT.ENABLE (100000);
--fnd_file.put_line (fnd_file.output, '------------------------------------------------------' );
v_mailconn := UTL_SMTP.open_connection (gc_mailhost, 26);
UTL_SMTP.helo (v_mailconn, gc_mailhost);
UTL_SMTP.mail (v_mailconn, p_sender);
UTL_SMTP.rcpt (v_mailconn, p_recipient);
UTL_SMTP.open_data (v_mailconn);
msg :=
'Date: '
|| TO_CHAR (SYSDATE, 'Dy, DD Mon YYYY hh24:mi:ss')
|| crlf
|| 'From:[email protected] '
-- || p_sender
|| crlf
|| 'Subject: '
|| p_subject
|| crlf
|| 'To: [email protected]'
-- || p_recipient
|| crlf
|| 'MIME-Version: 3.1'
|| crlf
|| -- Use MIME mail standard
'Content-Type: multipart/mixed;'
|| crlf
|| ' boundary="-----SECBOUND"'
|| crlf
|| crlf
|| '-------SECBOUND'
|| crlf
|| 'Content-Type: text/plain;'
|| crlf
|| 'Content-Transfer_Encoding: 7bit'
|| crlf
|| crlf
|| p_mailbodyhdr
|| crlf
|| crlf
|| p_mailbody
|| crlf
|| crlf
|| crlf
|| crlf
|| -- Message body
'Regards'
|| crlf
|| 'HR and Payroll Team'
|| crlf
|| crlf
|| ' Note- Please ignore the leave status and number of days.'
|| crlf
|| crlf
|| '-------SECBOUND'
|| crlf
|| 'Content-Type'
|| ': '
|| p_filetype
|| crlf
|| 'Content-Disposition: attachment; filename="'
-- || 'Create Accounting'
-- || '.REQ'
||p_filename -- p_filename
|| '"'
|| crlf
|| 'Content-Transfer-Encoding: base64'
|| crlf
|| crlf;
UTL_SMTP.write_data (v_mailconn, msg);
src_file := BFILENAME (dir_name, p_filename);
DBMS_LOB.fileopen (src_file, DBMS_LOB.file_readonly);
v_length := DBMS_LOB.getlength (src_file);
WHILE i < v_length
LOOP
DBMS_LOB.READ (src_file, v_buffer_size, i, v_raw);
UTL_SMTP.write_raw_data (v_mailconn,
UTL_ENCODE.base64_encode (v_raw)
UTL_SMTP.write_data (v_mailconn, UTL_TCP.crlf);
i := i + v_buffer_size;
END LOOP while_loop;
UTL_SMTP.write_data (v_mailconn, last_boundary);
UTL_SMTP.write_data (v_mailconn, UTL_TCP.crlf);
DBMS_LOB.fileclose (src_file);
UTL_SMTP.close_data (v_mailconn);
UTL_SMTP.quit (v_mailconn);
EXCEPTION
WHEN OTHERS
THEN
UTL_SMTP.quit (v_mailconn);
DBMS_OUTPUT.put_line (SQLCODE || SQLERRM);
-- FND_FILE.PUT_LINE (FND_FILE.LOG,'error while fetching values from CO_CODE'|| SQLERRM );
END send_mail;
END xx_create_acct;Edited by: BluShadow on 18-Apr-2011 09:49
added {noformat}{noformat} tags. Please see the [url=SQL and PL/SQL FAQ and PL/SQL FAQ[/url] for info on how to post on the forumsI didn't get the information, What I want. Anyway, in the BLOB writing portion you have to create a temporary LOB and load your file into that temporary LOB and the write it into chunks.
Something like
DBMS_LOB.OPEN(v_src_loc, DBMS_LOB.LOB_READONLY); --Read the file
DBMS_LOB.CREATETEMPORARY(l_blob, TRUE); --Create temporary LOB to store the file.
v_amount := DBMS_LOB.GETLENGTH(v_src_loc); --Amount to store.
DBMS_LOB.LOADFROMFILE(l_blob, v_src_loc, v_amount); -- Loading from file into temporary LOB
/* Writing the BLOL in chunks */
WHILE l_pos < l_blob_len LOOP
DBMS_LOB.READ(l_blob, l_amount, l_pos, l_buffer);
UTL_SMTP.write_raw_data(v_connection_handle,
UTL_ENCODE.BASE64_ENCODE(l_buffer));
UTL_SMTP.WRITE_DATA(v_connection_handle, UTL_TCP.CRLF);
l_buffer := NULL;
l_pos := l_pos + l_amount;
END LOOP;For more example see these posts:
Re: Sending UTL_SMTP mail with single jpg attachment issue
Re: getting junk letters instead of photo in an email. -
Revision: 14812
Revision: 14812
Author: [email protected]
Date: 2010-03-17 09:02:11 -0700 (Wed, 17 Mar 2010)
Log Message:
Fix bug where setting a resource a second time on a VideoElement caused an RTE due to the loadStateChange event listener being unregistered too soon.
Modified Paths:
osmf/trunk/framework/OSMF/org/osmf/media/LoadableElementBase.asRevision: 14812
Revision: 14812
Author: [email protected]
Date: 2010-03-17 09:02:11 -0700 (Wed, 17 Mar 2010)
Log Message:
Fix bug where setting a resource a second time on a VideoElement caused an RTE due to the loadStateChange event listener being unregistered too soon.
Modified Paths:
osmf/trunk/framework/OSMF/org/osmf/media/LoadableElementBase.as -
ITunes 9.2 Causing Continual Reset after 5 minutes of Sync
iTunes 9.2 causing continual reset after 5 minutes of syncing. This never happened with earlier versions. The iPhone basically reboots and takes a very long time to execute that reboot.
I am having the same issue, itunes is 'stuck' syncing with my Apple TV for hours and hours, no new content is viewable or playable, yet the previously synced items are still available, as well as my music library and photos.
I've tried rebooting the Apple TV, as well as my Mac, the network is working just great in all other aspects. (airport extreme base station router)
It seems that every time I update to the latest Apple software, I experience problems.
Updated to the latest Safari and my entire network went completely 'screwy' for days then just magically started working fine again. (this happened last time Apple released a new version of Safari)
Now I have the latest itunes, and suddenly this strange sync problem with my Apple TV.
Very frustrating, and equally mysterious how these problems just seem to 'fix themselves' after a few days (sometimes weeks) after updating Apple software. -
Flash Player update causes radio on-line not to function
I have Windows 8 and use Firefox as browser. The recent Flash Player update has caused radio on-line not to function. I have tried uninstalling and re-installing Flash but the programme won't install. It downloads and then sticks, I've tried about 10 times! I overcame this by re-installing an older version and then my radio on-line works but when Flash automatically updated the programme the same thing occurred and radio no longer worked. I contacted Know How but they couldn't find out what the problem is either. Please can you advise me how to fix this.
Ken,
Same problem here. I use
http://www.webaudioplus.com/
as well and started experiencing the same problem after the latest
upgrade. Like you I didn't hear any clicks and pops at various
pitches until after the upgrade and have been making .swf files Web
Audio Plus for about a year.
Interestingly enough, when I play the file directly by
dbl/clicking on it, and just play via the Web Audio Plus media
buttons, the file plays just fine.
And the problem does not seem to be germane only to my PC as
though it was a sound card related issue because the same thing
happens when I play web files I have done in the past on my
assistants PC that were fine but since the latest Flash upgrade now
they have the same issues as my PC when playing the files embedded
on a web page.
I had not tried restoring (I'm on XPpro) but obviously that
only solves the problem for me. I'm starting to get complaints in
our Support Desk about this.
I appreciate your post. It's the only one I could find on the
subject.
I certainly hate to think this is something Macromedia is
going to blame on Web Audio Plus.
If I find anything in my research I'll be sure to post it
here.
Mike C. -
Revision: 3966
Author: [email protected]
Date: 2008-10-30 06:40:39 -0700 (Thu, 30 Oct 2008)
Log Message:
Fix incremental compile which broke at some point since Flex 3 due to compiler changes.
ResourceManager.fetch() assumes a local file and uses java.io.File to check if the file exists. Files within swcs such as framework.swc$Assets.swf and framework.swc$default.css will never exist so they triggered a recompile. For now, put the dependency on the swcArchive file itself since that does exist in the file system.
The dependency checking is still weak and could use some more work but at least now it doesn't recompile every time when there are no changes.
QE Notes: None
Doc Notes: None
Bugs: - SDK-17715
Reviewer: Paul
Ticket Links:
http://bugs.adobe.com/jira/browse/SDK-17715
Modified Paths:
flex/sdk/trunk/modules/webtier/j2ee/servlet/src/java/flex/webtier/server/j2ee/BaseCompile Filter.javaI enabled the settings in the labview.ini
I found some text files that looked like logs "LabVIEW_8.5_Matt_cur.txt" "LabVIEW_8.5_Matt_log.txt". Which contained some error logs and call after I tried to compile. I attached some logs from my attempts to compile. For the errors that referenced a vi and a statechart guard, I remade the vi and the referenced guard. The others all have
..... /drawmgr.cpp(3570) : DAbort: Couldn't create 24 pen Error ==0
in common and some had a
....../image.cpp(13927) : DWarn: could not get hdc error = 0
warning. I'm guesing these are related to the graphical problem I'm getting with explorer. But since I can't decode the call stack I'm not sure what the source is (assuming the cause is within the call stack).
It looks like LV 8.6 Beta is going to open soon. Does anyone know if Vision will work with it? And Is there any kind of obligation to use the beta regularly? Since if it doesn't help much, I'd probably just end up removing it.
Matt W
Attachments:
errors.zip 7 KB -
Hi All,
Due to attribute change run (SID's is missing) process chain is failed.kindly suggest me how we can rectify for this issue.
Thanks
Ragavif master data is loading at same time while the attr/hier change run is occuring,it cause the change run to fail.
Usually u get error message like..user ALEREMOTE has locked the MD tables..
Wait for some time and then try attr change run manually by going to rsa1->tools->apply hier/attr change..
if it still shows locked..try to see in rsmo if a MD load has got stuck..
else..see in sm12 to find lock is on which tables..
last resort..delete lock forcefully from sm12..
first option is wait for some time and give a try again..
cheers,
Vishvesh -
I can not sync my IPhone to My Imac. I have the latest version of ITunes on my Imac. I have tried reseting my phone (3), changing ports. Nothing works. I was thinking maybe my phone has the earlier version of ITunes but I can't update it.
Did you already have a look at this article?
iPhone, iPad, iPod touch: Device not recognized in iTunes for Mac OS X -
The synchronisation of iphone 4S to windows 7/64 bit does no longer work; kalender, individual ringtones and contacts get not sychronized in both directions. I tried reset on working configuration, deinstallation of itunes - nothing worked - what can be done to solve?
Couple of things to check:
You are using Outlook 2003, 2007 or 2010
You have selected to sync Calendars and Contacts with Outlook on the Info tab of your iTunes sync settings
You have selected your Outlook calendar as the default claendar on your iPhone (in Settings>Mail,Contacts,Calendars>Default Calendar)
If all that is correct and iTunes still won't sync correctly, you might have to try reinstalling Outlook. Another option is to enable iCloud syncing with Outlook (see http://www.apple.com/icloud/setup/). This requires Outlook 2007 or 2010. If you decide to sync using iCloud but sure to disable contacts and calendar syncing in iTunes on the Info tab of your sync settings. Do not try to sync with both Outlook and iCloud or you will end up with duplicates in your contacts and calendar.
For syncing Ringtones confirm that:
The file is really a ringtone (right-click the file in iTunes, select Get Info, on the Summary tab it should say "Kind: Ringtone".
You have checked each of the ringtones you want to sync
You have checked "Sync only checked songs and videos" on the Summary tab of your iTunes sync settings
You have checked Sync Tones on the Tones tab of your iTunes sync settings -
I have backed up my MAC to Time Capsule with Time Machine, erased HDD and clean installed OX Yosemite. After installation I have to reconfigure Wi Fi, so I reset my Time Capsule changed password. Now I cannot see my previous back up on reinstalled MAC. Neither on TM nor on the Manual search. In finder appeared new disk. I am pretty sure that old files are still there. Can anybody suggest how to retrieve them.
This sounds like classic Yosemite.
What you did is fine.. there is no way to delete the backups via the reset button.
What I would suggest is a new clean setup of the TC again.. use a full factory reset.
Factory reset universal
Power off the TC.. ie pull the power cord or power off at the wall.. wait 10sec.. hold in the reset button.. be gentle.. power on again still holding in reset.. and keep holding it in for another 10sec. You may need some help as it is hard to both hold in reset and apply power. It will show success by rapidly blinking the front led. Release the reset.. and wait a couple of min for the TC to reset and come back with factory settings. If the front LED doesn’t blink rapidly you missed it and simply try again. The reset is fairly fragile in these.. press it so you feel it just click and no more.. I have seen people bend the lever or even break it. I use a toothpick as tool.
N.B. None of your files on the hard disk of the TC are deleted.. this simply clears out the router settings of the TC.
Redo the setup from the airport utility in the Yosemite computer..
Do not use the recommend names.. use really short names.. no spaces and pure alphanumeric.
eg TCgenx and TCwifi for basestation and wireless names.
You can also setup wireless password as before but I strongly recommend 8-20 character pure alphanumeric mixed case and numbers.. no characters outside of that.
Then mount the TC manually in finder.
Go, Connect to server.
Type in the TC IP address if at all possible.. it is more likely to be reliable than using name.
SMB://10.0.1.1 (replace with your IP but it should be static.. that is default)
Or
SMB://TCgenx.local (use whatever name you have given it.. plus the domain which is always local)
when asked for the disk password supply it and save in the keychain. Then open the disk in finder and you should see your sparsebundle in there.. from migrate assistant you should now be able to see your backup. -
Rebate Agreement - No correction due to value change
Dear Friends,
I am facing a problem in Rebates. When I am opening the Rebates Agreement, the system prompts the following message "The sales volume for agreement _________ is not current." I have tried using the T-Code VBOF but the system prompts for the following error -
9202507314 (Billing Doc No) No correction due to value change
9202507363 (Billing Doc No) No correction due to value change
I have checked both the billing Document and checked for changes but there is not changes that was made to the billing Document.
Kindly suggest a solution.
Reagrds
Vineet JainDear Vineet,
I have the same problem while running VBOF few billing documents are showing as not updated with the message "No correction due to value change".
But I have found that those documents are belongs to other agreements of the same customer number.
Can you please help me, which sap note should apply to over come this error message.
Thanks in advance.
Anjan Kumar.
Maybe you are looking for
-
Error message when opening iTunes after updating Windows 8.1
I recently updated my windows software to 8.1. Now I am getting a message that iTunes stopped responding and must close. I tried to uninstall and reinstall iTunes but that has not fixed the problem. I cannot get iTunes to open. There is no error
-
Hello, I created a data text variable user exit. everyting works fine, but, 1) Selection options: Year: 2010 Month: 1 to 11 The query and text variable return right values Year 2010 Month: Jan to Nov but, if i want to make new selection 2) Year : 201
-
No sms after updating to iOS 6.1.2
Hi everyone, I can't send text messages from my good old 3GS after installing iOS 6.1.2. Of course I tried the simcard in another cellphone, works like a charm. I also tried another simcard in my 3GS (from another carrier, since it's an unlocked iPho
-
IPhoto 2 recognizes camera but not pictures that are on it
I just purchased a Casio Exilim S-600 digital camera. It came with its own PhotoLoader software and it recognizes the camera but does not recognize the photos. The PhotoLoader also works with OS 9 so I would prefer to use iPhoto. When I plug the came
-
Hi, After upgrading to iOS7, I was asked by the system to set an passcode. When i try to swipe from the notification area, it navigates me to the passcode lock screen which is expected but the same behaviour is not shown for a call - when i swipe fro