AIR BR1310G Dot11Radio0 reset down
Interface IP-Address OK? Method Status Protocol
BVI1 19.165.30.6 YES NVRAM up up
Dot11Radio0 unassigned YES NVRAM reset down
Dot11Radio0.516 unassigned YES unset reset down
FastEthernet0 unassigned YES NVRAM up up
FastEthernet0.516 unassigned YES unset up up
Cannot get this non root Dot11radio 0 interface to any state other than Reset down---any ideas
halbr004#show controllers dot11Radio0
interface Dot11Radio0
Radio AIR-MP31G, Base Address 003a.9926.aa20, BBlock version 0.00, Software version 5.80.15
Serial number: FOC1439B6P2
Number of supported simultaneous BSSID on Dot11Radio0: 8
Carrier Set: Americas (US )
DFS Required: No
Current Frequency: 2457 MHz Channel 10
Allowed Frequencies: 2412(1) 2417(2) 2422(3) 2427(4) 2432(5) 2437(6) 2442(7) 2447(8) 2452(9) 2457(10) 2462(11)
Current CCK Power: 100 mW
Allowed CCK Power Levels: 1 5 10 20 30 50 100
Current OFDM Power: 30 mW
Allowed OFDM Power Levels: 1 5 10 20 30
ERP settings: short slot time.
Neighbors in non-erp mode:
Current Rates: basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
Active Rates: basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
Allowed Rates: 1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
Best Range Rates: basic-1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
Best Throughput Rates: basic-1.0 basic-2.0 basic-5.5 basic-6.0 basic-9.0 basic-11.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
Default Rates: basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
Channel / Max Power Table
Length of RID = 122
Radio Type = 32
Reg Domain = 0
Freq : Min,Max = 2412 , 2462
Channel Number = 1, OFDM = 15, DSSS = 20
Channel Number = 2, OFDM = 15, DSSS = 20
Channel Number = 3, OFDM = 15, DSSS = 20
Channel Number = 4, OFDM = 15, DSSS = 20
Channel Number = 5, OFDM = 15, DSSS = 20
Channel Number = 6, OFDM = 15, DSSS = 20
Channel Number = 7, OFDM = 15, DSSS = 20
Channel Number = 8, OFDM = 15, DSSS = 20
Channel Number = 9, OFDM = 15, DSSS = 20
Channel Number = 10, OFDM = 15, DSSS = 20
Channel Number = 11, OFDM = 15, DSSS = 20
Pls attach your config & "show version" output from this AP
HTH
Rasika
Similar Messages
-
Dot11Radio0 Interface in reset/down status
Hi,
I have the next problem.
The interface Dot11radio0 is always in reset / down status.
I can't link both AP.
They both are cisco AIR-AP1252AG-E-K9.
This have been working fine for 18 months, but this week suddenly went down.
I updated yesterday one of the APs to a new version, from the 12.4.10b-JDA3(GD) to the c1250-k9w7-tar.124-25d.JA1.tar but the problem was no fixed.
the other AP has 12.4.21a-JY(ED).
I've changes the role of the APs, the one with was root-bridge changed to non root-bridge and the one with was non root-bridge become root bridge.
Doing this, I changed the status of the interfaces, the AP with had interface dot11radio0 up up, become in reset down, and the AP that previously was in reset down, become in up up.
In the show log I see that the problem is:
Dot11Radio0, cannot associate: Authenticating
Interface Dot11Radio0, cannot associate: No Response
I leave the confs here.
Please, help me.Hi Surendra,
I'm getting:
The bug ID CSCtc23789 does not exist. Please verify the bug ID and try again. If you feel you reached this message in error, please send us
feedback
including the bug ID in question. Thank you.
What's the BugID and I can look it up. I will rate your post! -
My Macbook air (late 2010) shuts down randomly!!
Need some help here!! My Macbook air (late 2010) shuts down randomly, sometimes it won't even power on. This happened to me one morning, then at night try turning it back on, it went back to normal, I didnt do anything to it. Today it did it again but it went back to normal few minutes later after hitting the power buttom more than 10 times
Hi Argenisss,
I'm sorry you are having issues with your Macbook Air. Since your post indicates you have the latest version of the operating system, I would suggest resetting the System Management Controller (SMC)
Intel-based Macs: Resetting the System Management Controller (SMC)
Power
The computer doesn't respond to the power button when pressed.
A portable Mac doesn't appear to respond properly when you close or open the lid.
The computer sleeps or shuts down unexpectedly.
The battery does not appear to be charging properly.
The MagSafe power adaptor LED doesn't appear to indicate the correct activity.
Shut down the computer.
Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time.
Release all the keys and the power button at the same time.
Press the power button to turn on the computer.
Note: The LED on the MagSafe power adapter may change states or temporarily turn off when you reset the SMC.
Another troubleshooting step would be to reset the PRAM as well:
About NVRAM and PRAM
Resetting NVRAM / PRAM
Shut down your Mac.
Locate the following keys on the keyboard: Command (⌘), Option, P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys.
You can read more details by clicking on the two links above, but these would be two good troubleshooting steps to try.
Hopefully, this information will help ....
- Judy -
Wireless Bridge error with AIR-BR1310G-E-K9,cannot associate: No response
Hi Guys,
I have to do a wireless bridge with 2 AIR-BR1310G-E-K9. I configure 1 AP root bridge and 1 AP non-root bridge, with the same SSID.
But on the AP non-root bridge, the interface dot11 radio don't change it state to up and give this error: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: No Response.
I don't why it doesn't work. Even if i try a configuration which it already work on a site, it doesn't work to.
So I ask to me if there is a problem with internal antenna?
If I configure the 2 AP to access point role with 2 different ssid, I can see the 2 ssid but with a weak signal.
This AP can work without external antennas?
Thanks for your helpHi Jerome,
The 1310 definitely can work with the internal antenna but... is the AP mounted somewhere? Some mounting options imply an external antenna as they position the internal antenna toward the wall... -
Dear All,
is it possible to set AIR-BR1310G-A-K9 AP on dual radio.
i am getting the expected coverage on 2.4 GHz radio when set as AP. in open air its giving hardly 25-30 meters of coverage. my purpose is to distribute internet bandwidth on wireless for hotel customers.
how can i get better coverage area ?
what is other alternative to AIR-BR1310G-A-K9 ?
if i go for external antena which antena shuld i select?
thanks in advanceWith the AIR-BR1310-A-K9 you have no options for external antenna. You would need the AIR-BR1310-A-K9-R to use an external antenna only.
If you are mounting the unit indoors, then I would recommend the 1200 AP.
If you are mouting outside, then the 1300 is the easiest to use outdoors.
Seth -
i want to turn my macbook air off. the shut down button already appeared but the mouse/cursor just hang and won't work. even after pressing the enter button to shut my mac off won't work. what will i do?
This is not a reply. I just want to elaborate on this problem.
My computer freezes occasionally when it is used after being sleep for a while. The spinning ball appears and everything is totally disabled. Nothing on the keyboard works.
The mouse moves, but does not work.
The only solution is to turn the power off and on (losing all data in open applications.)
I kept the System monitor running on the side to find out which program was running when the computer froze. The Monitor as well as all other applications froze, but the data showed:
Firefox 18.4%
Activity Monitor 0.9%
Firefox Plugin 0.2%
This is all the information I have. By the way, I am using iMac with OS 10.6. -
MY macbook Air just started shutting down suddenly
MY 2011 Macbook Air just started shutting down when I watch Hulu and Skype. What is wrong?
It turns back on fine then within 15 mins, it'll shut off completely. So far, it only shuts off when I'm using Skype or watching videos...After it restarted, did you see a dialog box resembling this one:
If so, next time it occurs click Report...
Before you send it to Apple, copy the text of the report. Paste it in a reply. Remove or obscure any personal information, should it appear. -
I have a mac book air. I felt down and I have broken the screen: several white lines on the screen. Do you know if I can only change the screen? Is it expensive?
Welcome to Apple Support Communities
Take your MacBook Air to an Apple Store or reseller to have your display replaced. If you want, you can buy the display yourself and install it, but as you can see, that's expensive > http://www.ifixit.com/MacBook-Parts/MacBook-Air-13-Inch-Mid-2012-Display-Assembl y/IF188-083?utm_source=ifixit_guide&utm_medium=guide_intro&utm_content=required_ items&utm_term=macbook_air_13%22_mid_2012 -
My macbook air will not shut down or restart
my macbook air will not shut down or restart, but it will go to sleep. what can i do to fix this ?
correction its a macbook pro
-
DVI ADAPTOR iPad air crashes and resets after 5 or 30 minutes when i connect dvi adaptor
DVI ADAPTOR iPad air crashes and resets after 5 or 30 minutes when i connect dvi adaptor I don't know the reason Sometimes its ok for more than 30 min and suddenly then crashes and the iPad resets
For those still wondering how to install ios 6.1 on 5th gen iPod, you need to download it off of apples official website and then shift click restore from backup and choose the downloaded ios 6.1
apples one year warrant covers any hardware problems like these right? -
AIR-BR1310G-A-K9R Integrated Antenna
I have a couple of BR1310 with the integrated antenna. I am getting an extremely weak signal out of the antenna about a 70 DB loss sitting 10 feet away from the AP. Is there an IOS command to the enable the integrated antenna, I also opened one of the AP up and I did not see an antenna in the casing. Just curious if anyone has any insight?
THe reason there is no internal antenna is the model number you reference is for an 1310 with the remote antenna option. thats the R at the end.
this is the reference
Antenna Recommendations
â¢AIR-BR1310G-x-K9 has a single integrated antenna and is not configurable for antenna selection (diversity/left/right). The x represents your regulatory region.
â¢AIR-BR1310G-x-K9-R does not ship with an antenna because many different external antennas can be used with this product to cover various environments and applications. You must install one or two external antennas. The x represents your regulatory region. For additional information on antennas and accessories, refer to this URL:
http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a008022b11b.html
-If two diversity antennas are installed, Cisco recommends that you configure Diversity for the antenna receive and antenna transmit settings.
-If only one antenna is installed, Cisco recommends that you connect it to the right RP-TNC antenna connector and that you configure Right (Primary) for the antenna receive and antenna transmit settings.
Here is the link to the document referenced above.
http://www.cisco.com/en/US/docs/wireless/access_point/1300/ios/read_me_first/sheet/ReadMe.html#wp37024
Bill -
Power over ethernet for AIR-BR1310G
Hello
i have AIR-BR1310G that came with its proper power injector AIR-PWRINJ-BLR2 can this power injector be feed using a POE switch or do i have to use the 48v power adapter
regards
ElieELie: no PoE. You can only use power supply to operate the bridge.
HTH
Amjad
Sent from Cisco Technical Support iPad App -
My Mac Air doesn't shut down. It gets stuck on the grey screen!!!
My Mac Air doesn't shut down. It gets stuck on the grey screen!!!
-
Can not get my ipad air 2 to reset or reboot
I have an ipad air 2 that I believe is running IOS 8.1. I jailbroke it using Pangu. After not finding much need for a jailbroken devise I went to reset the ipad to factory settings. I backed up the devise to my macbook and followed the reset procedure going to settings, general, reset, and erase all content and settings. The ipad then restarted and it appeared to be doing it's thing. The ipad rebooted after a while and the apple logo appeared, then After about 2 hours the apple logo was still there and it seemed to be stuck.
I then plugged the ipad into my computer and opened itunes. itunes recognized the ipad and give me the option to set it up as a new devise or restore from back up. I choose to sset up as a new devise. The ipad then just displayed the apple logo for a few more hours, once again it seemed to be stuck. I preformed a hard reset on the ipad by holding the power and home buttons at the same time and reconected it to itunes. Now itunes does not even recognize the ipad when it is plugged into the computer. I reset the devise several times and it still will not get past the apple logo.
I then powered the ipad off and let it sit overnight while I searched online for a solution to this problem. the next day it appears that the battery had been completely drained because I was getting the low battery symbol when I was trying to turn the ipad back on. I then plugged it into my macbook and let the battery recharge for about an hour. I then tried to put the ipad in rocovery more and reset it from itunes, but now it looks like it is not going into recovery more. I have held down the home and power buttons while powering on in an attempt to put it into recovery mode and that does not seem to be working. I tried to do a recovery fix using redsn0w but that did not work either.
I would really like to be able to fix this thing on my own before sending it to apple. If anyone has any ideas or suggestions on how to fix it I am all ears. At this point I just want to reset it to factory settings. I do not care if I am able to recover any of the data that was on it. If anyone can help me get this things working I would be willing to send you some $$$ via Paypal for your time. ThanksJailbreaking violates the Apple warranty and licensing agreement and voids ALL support from Apple. No one on here can help you as doing so is a violation of the Terms of Use of these Communities. If you send the iPad to Apple they will just send it back to you as they are not permitted to work on a machine that has been jailbroken.
-
857 Router Dot11Radio0 reset - problem
Hi all
I have just upgraded the IOS in a 857 Router to this:
ROUTER#sh version
Cisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T7, RELEASE SOFTWARE (fc3)
but now I can't get the dot11radio 0 interface to come up. I just get a message saying the interface is reset and line protocol is down. I get this error message when I remove and re-insert the SSID -
ROUTER(config)#int dot11radio 0
ROUTER(config-if)#no ssid SSID
*Mar 1 04:04:24.655: %DOT11-4-NO_SSID: No SSID configured. Dot11Radio0 not started.
ROUTER(config-if)#ssid SSID
ROUTER(config-if)#
*Mar 1 04:04:24.655: %DOT11-4-NO_SSID: No SSID configured. Dot11Radio0 not started.
'Show run' shows the ssid is configured on the interface but the error message is saying that it doesn't have an ssid, even after a 'copy run start' and a 'reload'
I have spent hours on this and I can't find the problem. I have done numerous 'write erase' and 'reload' as well as re-installing the IOS twice.
Any advice would be very appreciated.
--- show output ---
ROUTER# sh ip int dot11Radio 0
Dot11Radio0 is reset, line protocol is down
Internet protocol processing disabled
ROUTER#sh int dot
ROUTER#sh int dot11Radio 0
Dot11Radio0 is reset, line protocol is down
Hardware is 802.11G Radio, address is xxxx.xxxx.xxxx (bia xxxx.xxxx.xxxx)
Description: WLAN
MTU 1500 bytes, BW 54000 Kbit/sec, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/30 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
ROUTER#
--- show run summary ---
dot11 syslog
dot11 ssid SSID
vlan 1
authentication open
authentication key-management wpa
wpa-psk ascii 0 ppppppppppp
bridge irb
interface ATM0
no ip address
no atm ilmi-keepalive
dsl operating-mode auto
interface ATM0.1 point-to-point
pvc 8/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
interface Dot11Radio0
description WLAN
no ip address
encryption vlan 1 mode ciphers tkip
ssid SSID
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
infrastructure-client
no cdp enable
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Vlan1
description Bridged LAN and WLAN
no ip address
ip virtual-reassembly
ip tcp adjust-mss 1452
bridge-group 1
bridge-group 1 spanning-disabled
interface Dialer1
description $OUTSIDE$
ip address negotiated
no ip redirects
no ip unreachables
ip nat outside
ip virtual-reassembly
encapsulation ppp
no ip route-cache cef
no ip route-cache
ip tcp adjust-mss 1242
no ip mroute-cache
dialer pool 1
dialer-group 1
no cdp enable
ppp authentication pap ppppppp
ppp chap refuse
ppp pap sent-username uuuuuuuuu password 0 ppppppp
interface BVI1
ip address xxx.xxx.xxx.xxx 255.255.255.0
ip nat inside
ip virtual-reassemblyNot to worry everyone. I have figured it out. I replaced the dot11radio 0 intface with this config
interface Dot11Radio0
description WLAN
no ip address
encryption vlan 1 mode ciphers tkip
ssid SSID
no cdp enable
no ip address
no shutdown
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
infrastructure-client
and added in this config for the sub interface which was missing:
interface Dot11Radio0.1
encapsulation dot1Q 1 native
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
Thanks anyway.
Maybe you are looking for
-
Can anyone explain what I need to do. I am buying a new computer, need to de-authorise my old computer and then put the library on a new windows computer. I have my library backed up to the cloud for which I pay extra. I am not at all technical so
-
Include ZXM06U02 in EXIT_SAPLEINM_002
Hi gurus, i've tried to add my z-segment ZE1EDP01 into int_edidd like it is described in the following link: http://help.sap.com/saphelp_dimp50/helpdata/DE/dc/6b7d7c43d711d1893e0000e8323c4f/content.htm The z-segment will be added, but the idoc went t
-
This Grandma needs help choosing an Intel computer. My PB4 is a very good friend, but I need easy access to PC CDs for my obession, family history. I have an extra monitor, SyncMaster 192 mp, and wireless keyboard and mouse. Would the new mini 80G be
-
Authentication Problem for WebService
Dear All, I have some existing interface which are SOAP to RFC synchronous.In this I am genreting WSDL and providing this WSDL to sender side and it is working fine. But when I have used same WSDL and Provide to some other application people and when
-
Dynamic file name for report export to csv
If "Enable CSV output" = "YES" for a report region titled "Invoices", the default file name is "Invoices.csv". If I have a parameter, Pn_MONTH, for the month (e.g. Jan 2010, Feb 2010, etc.) and the report only shows data for that month, I would like